Search Documents

By J. E. JR. Johnson

AT the Cleveland meeting of the Institute in October, 1912, I had the honor to present a paper outlining the conditions surrounding the charcoal iron industry, and giving some of the results of an investigation started about three years ago for the purpose of determining the reason for the poor reputation of the Lake Superior charcoal irons as compared with the Southern and Eastern irons. In that paper I explained the effect of high carbon on quality, and tried to make clear that that paper was a preliminary one, as we felt convinced that we should eventually discover other factors affecting quality. The progress of the investigation has brought out facts that seem to us of the utmost importance practically and theoretically, and the purpose of the present paper is to present these facts with the proofs which seem to us to establish them. The closing year of the nineteenth century saw the publication of the first definite and connected statement of the relationship between the cast irons and the steels.' The metallurgical world was ready to accept the fundamental unity of these two series, acceptance being greatly hastened by Professor Howe's classic paper, The Constitution of Cast Iron, presented at the Richmond meeting of the Institute, February, 1901.

Jan 1, 1914

By Rodolfo V. de la Cruz

The in situ deformability of rock masses is determined by relating the applied load to the radial displacements of points on the borehole wall that are outside of the loaded surfaces. The external displacement method includes the steps in which: a) radial displacement sensors are installed to measure the change in length of a diameter of a borehole; b) unidirectional self- equilibrating pair of forces perpendicular to the direction of radial displacement measurements are applied on opposite sectors of the borehole wall, and; c) using elastic theory, the in-situ deformability of the rock mass can be related with the applied loads and measured radial displacements. The displacements outside the loaded surfaces are comparatively smaller in magnitude than displacements inside the loaded surfaces. These displacements, however, are sufficiently large and can be measured precisely by commercially available linear displacement sensors. Loads are applied by a conventional borehole jack. Existing methods for measuring the in situ deformability of rock masses yields unreliable results due to complex boundary stresses, small and varying contact areas, and the existence of fractures. It was shown that in the external displacement method, the effect of boundary pressure distribution and contact area are negligible. Also, since the displacements measured in the external displacement method were due to materials that are deeper inside the rock mass, borehole fractures have less influence on the calculated deformation modulus.

Jan 1, 1982

By AIME AIME

AT A meeting of the Boston Local Section of the Institute, on Oct. 3, approval was voted to the work done by its representatives on the Committee opposing the passage of a bill by the, Massachusetts Legislature to license engineers. The report is as follows: The Joint Committee on Licensing of Engineers, which included a Committee of the Boston Society of Civil Engineers and representatives of seven other societies,* submitted to the members of the respective societies, on Jan. 8, 1921, a report in which it was stated that on Jan. 4, 1921, a petition was filed in the Legislature of Massachusetts by the Boston Chapter of the American Association of Engineers accompanied by a bill to provide for the registration of professional engineers and land surveyors. This report also stated that at a meeting of this committee, held on Jan. 7, 1921, it was voted:

Jan 1, 1921

By Ralph Hayden

PAGE I. IntRoduction........239 II. Definition of Anaconda SLime....240 III. The Source of Slime......240 Remodeled Flow Sheet......240 Old Plow Sheet,.......242 IV. ConStitution of Slimes......243 Chemical........243 Physical.........243 V. The Slime Problem.......247 VI. THe Experimental Slime Plant....248 VII. Slime Thickeners. ETc .......249 Slime Ponds........249 Tanks.........249 Comparative Efficiency of Open and Baffle Tanks .260 Callow Tanks........252 Kuchs-Laist Centrifugal Separator....253 Garred Filter........256 Dorr Continuous Thickener.....256 VIII. Concentrators........257 Round Table........558 Peck Centrifugal Concentrator....259 Competitive Tests.......260 Twenty-Deck Round Table..... 260 Slime Feed Distributor......261 IX. ConcluSion.........262 I. Introduction. In the wet concentration of ores there is always a certain amount of very fine material with which to contend. and which invariably carries such quantities of value that the treatment of it is worth while. commercially. This fine material usually contains that portion of the ore which hinders the separation of the mineral values: namely. the colloidal material resulting from the decomposition of certain constituents of the ore. The object of this paper is to show what efforts have been made to solve the slime problem as it occurs in the concentrator of the Washoe

Jan 1, 1914

By Joseph G. Debanné

Foreword The three case histories and the liquid fuels planning scenario presented in this paper span a twenty year period, from the pioneering days of computers in the petroleum producing industry during the mid-fifties, to the energy crisis era of the seventies. Inasmuch as two of the main actors, Ian McKinnon and I, are featured in all three case histories, while I am currently involved in the fossil fuels scenario, this paper provides four related and personal spot readings along an evolutionary path: from the one dimensional technical domain to the multi-dimensional techno-socio-economic domain of computer applications in the petroleum industry. Coincident with this evolution in the direction of increasingly comprehensive and powerful computer applications, the evolution in hardware/software capability and in analytical power are also kept in perspective. The three case histories are: 1. The Bonnie Glen-Wizard Lake Case (Calgary, Alberta, 1955-1957); 2. The TransCanada-Great Lakes Gas Transmission Case (Ottawa-Washington, 1966); 3. The Westcoast Transmission - El Paso Pipelines Gas Export/ Import Case (Ottawa-Vancouver-Washington, 1966-1967). The liquid fuels planning scenario is a demonstration exercise rather than a case history; however, it represents an important point on the evolutionary curve and, provides a concrete example of tech-

Jan 1, 1977

The total number of applications brought before the Committee during the year 1916 was 962; the total number, of persons who were elected, and became members of the Institute during the wane period was 750. The total membership of the Institute on. Dec. 31, 1916, was. 5,781, consisting of 19 Honorary Members, 5,246 Members, 215 Associate Members, and 301 Junior Members. The changes in membership during the year are shown on the accompanying schedule:

Jan 2, 1917

By B. B. Gottsberger

HAVE given considerable thought during the past year to the subject of licensing of engineers and par-ticularly to the position which the mining engineer should take on this question. I have found, however, that it is not a subject which yields much result for the thought expended on it. So far as any published record will show, mining engineers have been either ignorant of the extent to which the movement for the licensing of engineers has progressed or else indifferent to it. It is true that the Mining and Metallurgical Society of America, by a questionnaire sent out to its member-ship, did a great deal in calling this matter to the atten-tion of the mining profession, and so far as I know, the report of its committee, which analyzed the replies received, is the only published statement of the feelings and opinions of our branch of the engineering profes-sion. It is to be hoped that the conclusions shown by that report, namely, that mining engineers are almost unanimously opposed to the principle of licensing and consequently any legislation dealing with it, has received serious thought and that we are ready for an even more thorough consideration of the subject.

Jan 3, 1922

By C. F. Tolman

Discussion of the paper of C. F. TOLMAN, JR., presented at the New York meeting, February, 1916, and printed in Bulletin No. 110, February, 1916, pp. 401 to 433. Louis C. GRATON, Cambridge, Mass.-Of particular interest at this time is any paper that deals with chalcocite, the characteristic product of secondary enrichment and the copper mineral of greatest commercial importance, and that seeks to aid in the distinction between primary and secondary chalcocite-a distinction of much scientific and practical importance but one which thus far it has proved difficult to draw. The present paper on this subject by Professor Tolman, like the ,many preceding it which he and his colleagues at Stanford have published in the last couple of years, contains much of interest and suggestiveness. Without endeavoring at this time to review or comment upon Professor Tolman's conclusions in detail, I may say that many of them are in accord with the findings that my associates and I have been accumulating in the course of studying secondary enrichment in many of the copper deposits of the country. On the other hand, it goes without saying that in this comparatively new field of research or, at least, a field in which

Jan 5, 1916

By Paul F. Gnirk

INTRODUCTION The notion of permanent disposal of high-level radioactive waste in natural salt formations was formally proposed in 1957 by the Committee on Waste Disposal of the National Academy of Sciences- National Research Council. This proposal was the result of the Committee's deliberations in response to a request from the U.S. Atomic Energy Commission (AEC) in 1955 to assess the viability of geologic formations for such disposal. The research investigations for waste disposal in salt were initiated at the Oak Ridge National Laboratory (ORNL) in the late 1950's and continued through the 1960's and early 1970's at a relatively modest level of funding. During the period of transfer of Federal Administrative authority from the AEC to the Energy Research and Development Administration (ERDA) to the Department of Energy (DOE) during the latter part of the 197O’s, financial support for the research program was enhanced substantially. The program at OWL was regrouped under the Office of Waste Isolation (OWI) and later transferred to the Office of Nuclear Waste Isolation (ONWI) at Battelle Memorial Institute. With this enhancement in the research program, consideration of basalt, granite, shale, and tuff as repository host media was initiated. In February, 1980 the President of the United States established officially a comprehensive waste management program which called for the selection of the first repository site in 1985 from a suite of four or five potentially suitable sites, and initiation of a repository operation at that site in the mid-1990's. The current disposal system concept involves the emplacement of radioactive waste packages in mined disposal rooms at depth in suitable geologic formations, with closure of the facility effected

Jan 1, 1983

By Emil Gathmann

INTRODUCTION. IN presenting this paper I will attempt to answer certain questions proposed at this meeting and describe and illustrate methods of producing sound steel in an economical and hence commercial manner, which are adaptable to the production of practically all steel manufacturers, by readily effected rational changes in the methods of casting, cooling, and subsequent handling of the ingots. In some of the high-grade mills of America, where it is essential to obtain perfectly sound billets or blooms, it is the practice to discard from 35 to 40 per cent. of the crop- or pipe-end, and even with this excessive discard, secondary pipe or shrinkage-cavities are frequently discovered during subsequent working of the blooms and billets into their various manufactured products. The usual discard of from 10 to 20 per cent. from the crop-end of the ingot, which is made by the present generally employed methods of form and solidifying of the castings, certainly does not give the slightest assurance of the saleable product being physically sound or chemically homogeneous. I am aware that in the past there has been and at the present time there still is a decided difference of expert opinion as to what constitutes physically sound steel.

Jan 4, 1913

By Luther Wagoner

For a number of years I have, at odd times, tried to perfect a method of assay sufficiently delicate to find and estimate minute quantities of gold and silver. The object in view was to examine rocks remote from veins or mineral areas, in order to test the probability of the lateral-secretion theory. Having succeeded in measuring approximately the amount of gold and silver contained in one cubic centimeter of sea-water, I present a detailed account of the method employed, with some of the results obtained. General Method of Assay. The use of purified lead without other flux, blowpipe methods, extraction by cyanide, and measurement of the beads by the microscope. Purged Lead. The method of testing is by cupellation. On a properly prepared cupel, it is easy to cupel and find a bead of 0.002 mm. diameter. Such a bead of silver weighs about 1 part of a milligramme. A bead 0.02 mm. in diameter weighs about 1/24,000 mg., and a close approximation can be made to its weight. It is desirable that the lead used in the assay should be low in silver so as to avoid large correction, but as the parted

Jan 1, 1902

By James F. Howe

EveRy engineer and user of wire rope is desirous of information that will enable him to determine whether the performance of any particular piece of rope is satisfactory, and what conditions can be changed so as to increase the life of a rope. In most cases, it is far from easy to analyze the conditions of service and tell which is the greatest factor in determining the life of wire rope. If we start on a layout for an entirely new rope system, the task of making conditions satisfactory is simplified so far as the engineering details are concerned; but if the plant requiring wire rope is in operation, any change is likely to involve the expenditure of considerable money to replace and change over machinery that must be kept in constant operation, because a large monetary loss will result from a shutdown for even a few days. Often wire rope is kept operating under bad conditions, as the user thinks that it is cheaper and quicker to replace the rope than to make alterations in the hoisting machinery. A typical case is a metal mine operating in what is now almost the center of a large mining city, where it owns a few acres of mineral rights. It was expected that the shaft would go to a depth of 1000 ft. (305 m.), so a moderate-sized rope, about 1 1/4in. (31.7 mm.), was used on a 6-ft. drum with a 7-ft. head-frame sheave and rather short lead from drum to head sheave. This mine has gone deeper each year until it is now 2500 ft. deep and the rope speed has been increased from 1500 ft. per min. to over 3000 ft. The original rope just filled the drum in one layer, now it overwinds three layers. The original ropes were probably 6 X 19 crucible steel and lasted from 12 to 18 mo.; now, the highest grade plow steel is used, yet the average service is only about 6 mo. The cause is not hard to find. If the engineers had known at the outset what would be done with this hoist, the design would have been very different. Conditions at this mine, from a wire-rope standpoint, have gradually become worse and it is difficult to see how rope service on this hoist can be compared with the service of previous years with any fairness to the wire-

Jan 1, 1923

By James F. Howe

EveRy engineer and user of wire rope is desirous of information that will enable him to determine whether the performance of any particular piece of rope is satisfactory, and what conditions can be changed so as to increase the life of a rope. In most cases, it is far from easy to analyze the conditions of service and tell which is the greatest factor in determining the life of wire rope. If we start on a layout for an entirely new rope system, the task of making conditions satisfactory is simplified so far as the engineering details are concerned; but if the plant requiring wire rope is in operation, any change is likely to involve the expenditure of considerable money to replace and change over machinery that must be kept in constant operation, because a large monetary loss will result from a shutdown for even a few days. Often wire rope is kept operating under bad conditions, as the user thinks that it is cheaper and quicker to replace the rope than to make alterations in the hoisting machinery. A typical case is a metal mine operating in what is now almost the center of a large mining city, where it owns a few acres of mineral rights. It was expected that the shaft would go to a depth of 1000 ft. (305 m.), so a moderate-sized rope, about 1 1/4in. (31.7 mm.), was used on a 6-ft. drum with a 7-ft. head-frame sheave and rather short lead from drum to head sheave. This mine has gone deeper each year until it is now 2500 ft. deep and the rope speed has been increased from 1500 ft. per min. to over 3000 ft. The original rope just filled the drum in one layer, now it overwinds three layers. The original ropes were probably 6 X 19 crucible steel and lasted from 12 to 18 mo.; now, the highest grade plow steel is used, yet the average service is only about 6 mo. The cause is not hard to find. If the engineers had known at the outset what would be done with this hoist, the design would have been very different. Conditions at this mine, from a wire-rope standpoint, have gradually become worse and it is difficult to see how rope service on this hoist can be compared with the service of previous years with any fairness to the wire-

Jan 1, 1923

By J. Fred Johnson

COROMANT is the trade name of the alloy-steel drill rod tipped with a chisel-type tungsten-carbide bit manufactured by Sandvik Steel Works Co., Ltd. Other names, such as Swedish or air-leg method of drilling, are used in various localities. Coromant drilling in Sweden was the natural sequence of the adaptation of tungsten-carbide inserts to the already established routine of drilling. By the middle thirties the percussion drill had reached practically its highest attainable efficiency as a drilling machine. Since then improvement has been in metallurgy of component parts to increase life or lessen weight, in the development of pneumatic and automatic feeds, in the use of jumbos to more quickly and easily handle machines, and in changes in drill rods and bits. By 1937, drilling in the United States and Canada was done by relatively heavy mounted drifters with positive hand or automatic feeds. In Sweden, on the other hand, emphasis had been placed on light equipment and drifting was done with pneumatic bars and reverse-feed stopers. In 1938, one of the most prominent American drill manufacturers developed an air-leg for successfully drilling the extremely variable but relatively soft iron ores of some of the northern Michigan mines. Also in 1938, a comparative Swedish test, also in soft iron ore, of a 50-lb jackhammer mounted on an air-leg, against a 100-lb reverse-feed drifter on a pneumatic bar, showed the net drilling time was increased by the air-leg set-up from 51 to 71 pct, in drilling 6-ft rounds in a 6 1/2x6 1/2 ft drift. Miners were becoming scarce in Sweden even at that time and, since the lighter equipment made the work easier and more attractive, the airleg was then made use of in some types of soft rock. In 1940, for instance, a large tunnel for a hydroelectric plant was driven with this equipment. By 1943, when tungsten-carbide inserts came into the picture in Sweden, a great many of the kinks in percussion drilling with this hard-metal had been worked out in Germany under the stress of war conditions. However, only 10 pct of the drilling machines manufactured in Sweden were jackhammers for use on air-legs and only the one manufacturer made air-legs in the United States. American practice had largely supplanted integral forging of drill bits by the detachable steel bit. Canada and South Africa were using the one-pass throwaway bit but Sweden was still using the same old integral forged bit. After a long study of the trend toward simplicity

Jan 1, 1952

By Clarence Thom

This chapter presents, in summarized form, standard procedures for making separations of minerals from their ores by the froth flotation process to produce marketable concentrates. These are typical mineral separations which are being made commercially with the reagents and conditions generally used in the mining industry. Typical separations are presented for 17 metallic and 11 nonmetallic ores. The review of each includes a brief description of the mineral and the particular problem presented, general market specifications for its concentrates, an outline of treatment method, and kinds and quantities of reagents usually employed. This chapter does not include de- tails about ore preparation (crushing, grinding, and classification), elements of ore and pulp transportation (conveying and pumping), or concentrate preparation for market (thickening, filtering, and drying). In each presentation it is assumed, if not detailed further, that the ore is ground to the economical point of liberation of the minerals to be separated. Specific information, such as ratio of concentration and recovery, that depends upon the grade of ore being treated is considered beyond the scope of this chapter. Effective flotation separations that produce marketable concentrates may produce widely varying results in terms of percent recovery and still be economically profitable operations. Details of plant practice on specific ores are presented in Chapters 16 and 17. In this chapter the chemical names of the reagents are given. The extent to which different reagents are used in flotation plants in the U. S. is presented in Chapter 4. A compilation of the various flotation reagents, their trade names, manufacturers, and use has been prepared by H. T. Spedden. ANTIMONY The principal ore mineral of antimony, stibnite (Sb2 S3), is generally found in the U. S. in ore bodies in association with other valuable minerals such as galena (Pbs), sphalerite (ZnS), chalcopyrite (CuFeS2), or tetrahedrite (3Cu2 S – Sb2 S3), The sulfo-salt minerals of antimony, such as tetrahedrite or pyrargyrite, are often associated with high silver values, so that the presence of antimony may indicate economic importance even though the actual antimony content is low. Antimony is also significant to the mineral economy because of its occurrence in some ores where lead, gold, and silver are the

Jan 1, 1962

By D. Torrey

CONSIDERING the two great interests of to-day, in iron upon the one hand and steel upon the other, and recognizing with measurable distinctness the peculiar fitness of each for special services to which they are applied, the proposition to unite the two metals in combination, to bring into simultaneous use the peculiar advantages which each offers, has great attractions. The limited success which has been attained by trying to bring about such combinations of the two metals through the use of fluxes in welding, has led to the general adoption of the opinion that an effective union of the two metals is impracticable, or to the view that if practicable it would have but limited commercial value. Such opinions are, I think, premature and erroneous, and having gained some knowledge of the character and value of the "Wheeler process" for welding iron and steel without the use of fluxes, I submit the following observations and opinions of the matter for your information, with the hope of eliciting such a discussion of the subject as it may require. The principle of the invention is to bring the two metals simultaneously to a welding heat in one pile, and then to manipulate it.

Jan 1, 1879

By Richard Moldenke

In crowding the recent mass of work on the physics of cast-iron into the compass of a short review, I cannot do better than to follow the lines of Mr. W. R. Webster's suggestion, made at the Florida meeting of the Institute, March, 1895.' The classification of the properties of the metal, and the influences to which it is subjected during the various processes it undergoes, is quite complete; and as Mr. Webster gives it again in full in another paper at the present meeting, a simple reference to it now will be sufficient. I. Correspondence Between Chemical Composition, and Melting-Point, Fluidity, Shrinkage, Fracture,Chill, Micro-Structure, and Other Physical Properties. Melting-Point.—The melting-point of cast-iron had long been a subject of controversy among foundrymen. They knew that a hard iron melted faster than a soft one, but this effect was occasionally disputed, and the reasons given were unsatisfactory; but could not be well controverted. It was my good fortune to take the actual melting-temperatures of some 70 pig-irons and castings; the Le Chatelier pyrometer, suitably protected, being introduced into the interior, and the iron melted off in a specially-constructed cupola. The irons had been previously analyzed by taking the borings at the point of the intro-

Jan 1, 1905

By W. H. Adams

During the years when Americans were most active in investigations of the many substances containing nitrogen or ammonia, viz.: 1869 to 1875, my connection with certain chemical industries led me to experiments in the direction of the recovery of wastes from coal-gases. I take from my notes such memoranda as I think will be of interest, in the hope that some benefit may be derived therefrom by engineers at present attempting to utilize the waste products from coke-oven and blast-furnace gases. An examination of the conditions governing the manufacture of gas along the Atlantic seaboard, and an intimate knowledge of the mine-products used by the different large works, naturally led me at first to consider the well-known foreign methods of concentrating the available soluble salts in a modicum of water. The result was sufficiently promising to warrant a full line of experiments. At that time, no attention seemed to have been paid to the values of " gas-liquors." Nearly every gas-works in the United States wasted its wash-water in the sewers. The nitrogen in bituminous coals varies in quantity from 0.75 to 1.50 per cent. of the total weight. In the process of distillation in

Jan 1, 1887

The Reconstruction and Research Division of the United States Council of National Defense has, up to date, prepared two reviews on the above subjects: one covers foreign countries and the other covers the activities in the States. These reviews contain information appearing in various Governmental and public periodicals. While the information on foreign countries is necessarily incomplete and fragmentary, its summation is perhaps the most complete work of this kind so far accomplished. The information from the states consists mainly of bills and ordinances introduced in the state legislature, municipal councils, legislature committee reports, programs suggested by governors, and other state and local officials and local organizations It is realized that a good deal of this information will be useful to engineers studying conditions in the various states, and especially to those who want an insight into the general condition in all the states. For instance, the reconstruction problem in each state involving highway, reclamation, buildings, etc., are covered in detail.

Jan 8, 1919

By P. K. Koh

With identical annealing heal treatment the development of major annealed texture component seems to depend primarily upon the degree of cold reduction. Cube texture was evident on annealing- 1/2-, 1,/4- , and 1/8-mil tapes at 760°C, but it dissap-)eared on 927°C annealing of 1/8-mil tape cold reduced 96.9 pct. Some cube texturee remained as tile strongest 927 °C annealed texture component in 1/4- and 1/2-mil tapes cold reduced 93.8 and 87.5 pet, respectively. The switching coefficient increases and the squareness ratio of the hysteresis loop decreases proportionally with increasing cube pole concentration. PREVIOUS studies 1,2 on the 1/8-mil ultra-thin molybdenum permalloy tape established cold rolled and annealed textures and their magnetic performance for switch-core and coincident-current memory applications, The major cold-rolled texture was found to be of {110}<335> which is quite similar to the cold-rolled texture of silver and 70-30 cartridge brass. The major annealed texture components were found to be of {120)-- <001> and {113)<785>. Although the direction for easy magnetization for this type of alloy by the single-crystal technique is not avaliable, knowledge from related studies indicated [Ill] as the easy magnetization direction, similar to that of nickel.&apos; Therefore, a cube orientation, if present in the tape core, would be most detrimental to its magnetic performance.3 In its cold-rolled state the tape had < 111 > directions in the rolling plane 14.5 deg from the rolling direction.&apos; But the coercive force of the tape in such condition will be excessive due to large amounts of internal stresses, and therefore makes its use impossible for memory applications due to long switching time. In lower nickel alloys, suchas 50-50 nickel-iron and 65 pct Ni-Fe sheets, previous investigators4"7 found the presence of cube texture on annealing at 900° to 1000°C. Although no cube texture was found in annealed 1/8-mil tape,"&apos; its presence in some annealed 1,/4-mil tape cores was firmly established a year ago as verified by significant differences in magnetic properties. The present investigation is devoted to the orientation study and related magnetic measurements on three thicknesses of the ultra-thin tape, namely, 1/8 mil, 1/4 mil, and 1/2 mil, cold rolled directly from annealed 4-mil stock in the cold-rolled state as well as after they were annealed at 760°C (1400° F) and 927°C (1700°F). The results obtained might serve to elucidate the development of annealed texture as well as to establish clearly the importance of preferred orientation on the magnetic performance of such memory tape core despite its well-known low magnetic anisotropy exchange energy. EXPERIMENTAL PROCEDURE Samples were taken from one production heat (0.010 wt pct C, 0.004 P. 0.016 S, 0.80 Mn. 0.29 Si. 79.69 Ni. 4.42 Mo. 0.054 Co, 0.002 Ti, 0.12 Al, 0.04 Mg, 14.56 Fe). Annealed 4-mil sheets were cold re-

Jan 1, 1962