Search Documents

By M I. Pownceby, S Hapugoda, V Nunna

Deposits of low-grade iron ores containing abundant goethite are distributed across the world. A common difficulty associated with beneficiating goethitic-rich ores is the poor liberation characteristics of the iron-bearing minerals which often contain finely disseminated gangue minerals such as kaolinite, gibbsite and quartz. Microwave-assisted heating has been proposed as an effective way of inducing dehydroxylation and associated mineral transformations in order to beneficiate low-grade goethitic ores. In this research, the mineral transformations occurring in a low-grade goethite-rich sample using microwave radiation was studied. Roasting conditions (up to 1000°C and under various CO/CO2 gas atmospheres) were designed to generate a magnetic product from a goethite-rich, reject waste stream sample sourced from an iron ore processing site in the Pilbara, Western Australia. Conditions (T, pO2) for transforming the raw material from hydrated goethite to hematite and eventually to magnetite are presented. Chemical and mineralogical characterisation of the raw material and roast products were conducted using X-ray fluorescence, X-ray diffraction, optical microscopy and scanning electron microscopy techniques to identify the mineralogical and chemical changes occurring during the heat treatment. Further steps are suggested to optimise the microwave-assisted magnetising roasting and correlate it with the application of magnetic separation techniques to maximise the efficiency of upgrading the iron content in low-grade iron ores.CITATION:Nunna, V, Hapugoda, S and Pownceby, M I, 2017. Study of microwave-assisted magnetising roasting and mineral transformation of low-grade goethite iron ores, in Proceedings Iron Ore 2017, pp 575–582 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 24, 2017

By J Samosir, L Snyman

Northparkes was the first mine in Australia to use block cave mining method which relies on gravity and natural rock stresses to fragment and recover the ore. It was also the first hard rock mine to use hydraulic fracturing, in conjunction with CSIRO, to promote caving of E26 Lift 1. The technique was later used on E26 Lift 2 wedge and E48 prior to undercutting.Northparkes production is currently sourced from the E48 Lift 1 block cave mine and E26SLC. The E48 block cave contains economic ore to the north and south of the current cave footprint. To recover this ore the footprint has been extended on the north and south with two extraction drives and one extraction drive, respectively. Modelling of cavability above the additional drives indicated that the cave would not readily propagate to a sufficient height of draw to mobilise the ore and tended to arch over into the existing cave. To address the modelling results and to reduce the risk of the project, rock mass preconditioning was adopted.This fracturing campaign was performed from surface drill holes adjacent the subsidence zone angled to intersect the higher grade and higher elevation ore zones.Optical televiewer surveys, run prior to fracturing, picked intervals and fault zones to be avoided. Holes were resurveyed post-fracturing to detect newly created fractures and as a measure of success of the program.During fracturing operations water and gel fractures were run at varying depths and pumping pressure was logged for each fracture. The mine seismic system monitored significant events and dye in the fluids utilised for tracking water inflow locations during underground inspections.Towards the end of the project, guar fibres from gel were detected within the mill circuit and required treatment to resume optimum processing.CITATION:Webster, S, Snyman, L and Samosir, J, 2016. Preconditioning E48 cave extension adjacent to an active cave, in Proceedings Seventh International Conference and Exhibition on Mass Mining (MassMin 2016), pp 471–478 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 9, 2016

By N F. Fraser

Seafield ResourcesÆ offshore placer gold project covers c.10 000 km2 of the Westland continental shelf between Karamea and Jacksons Head, from the low-water mark out to the 120 m isobath (Figure 1). De Beers Marine (DBM), the marine diamond subsidiary of the De Beers Group, will carry out the project with geological input from Placer Solutions (PSL). DBM bring a wealth of expertise and advanced technology to the project, developed during their 20 years of exploration and mining of diamond placers on the Atlantic shelf of southern Africa, where they have also maintained a strong environmental record.   Glaciers and high-energy rivers emanating from the Southern Alps have transported substantial quantities of gold bearing sediment onto the Westland continental shelf during Pleistocene glacial periods, when fluvial gradients are steeper, sea level is c.120 m lower and most of the shelf is exposed. These deposits have been extensively reworked by the advancing shoreline and marine processes during interglacial marine transgressions, and most are now buried beneath a variable thickness of post-glacial marine sand, silt and mud. DBM will use side-scan sonar, swath bathymetry, Chirp sub-bottom profiling and a magnetometer to map the sea floor and sediments beneath it, guided by PSLÆs predictive geological model for gold distribution on the shelf. Cactus grab and vibro-core samples will be used to ground-truth the geophysics and provide stratigraphic, sedimentological and gold distribution data for incorporation into the geological model. Areas of interest identified by the geophysical and sampling data will be investigated in more detail, with closer-spaced geophysics and Mega-drill sampling to a maximum sediment depth of 20 m beneath the sea floor. These samples will be raised to the ship with air-lift suction technology, processed onboard for mineralogical and grade information, then returned to the sea floor. Environmental baseline data will be gathered from Van Veen grab samples of seabed sediment taken throughout the area during the prospecting programme.

Jan 1, 2005

An Investigation into the Flotation Behaviour of Pyrrhotite Present in the Merensky Orebody

Sep 13, 2010

Surface subsidence caused by coal mining operations was the subject of a very successful symposium organised by the Illawarra Branch of The Australasian Institute of Mining and Metallurgy in February, 1973. This symposium dealt with the principles of subsidence and overseas experiences arising out of underground mining. Since that time the New South Wales Department of Mineral Resources and Development (formerly the Department of Mines) has incorporated in the approval for pillar extraction certain conditions related to the monitoring of surface movement. Surveys and plans are required to be kept at mines where total or partial extraction of coal takes place. This paper traces the monitoring of surface movement in the Northern Coalfields of New South Wales over the past ten years. Reference is made to the National Coal Board's Subsidence Engineers' Handbook (1975) and how the guidelines expressed therein have been beneficial. Mining engineers in Australia are able to plan underground workings where minimum subsidence is allowable and are in a position to foreshadow the surface effects where total pillar extraction is carried out. In certain cases such surface effects can be minimised by structural design in buildings or pipelines.

Jan 1, 1980

By A Goldstone, T Maton

The Golden Cross Mine is located on the North Island of New Zealand, at the base of the Coromandel Peninsula, approximately 8 km northwest of Waihi. The project is operated as a Joint Venture with Coeur Gold New Zealand holding 800/0 and Viking Mining Limited with a 20% interest. The past open-pit and underground gold and silver producer has been in the reclamation phase of the operation for approximately 2.5 years and is now nearing completion. Although rehabilitation of the site is a regulatory requirement, the Closure Plan has been enhanced by the ongoing commitment of the Joint Venture to establish a sustainable land use for the site by commissioning engineered facilities designed to last for perpetuity. The Joint Venture identified six significant design features that were key to successful rehabilitation. These were the controlled placement of acid generating waste rock into engineered disposal sites; the design and placement of sealing layers over the waste rock disposal sites; the design and construction of diversion drains; the establishment and management of vegetation to protect the oxygen diffusion layer; a partial capping of the tailings to accelerate consolidation adjacent to the tailings dam embankment, and the implementation of a cyanide recovery circuit to recycle cyanide from the tailings prior to disposal. Another key to success for the project involved genuine consultation with all parties participating in the planning, evaluation, and consenting of the closure process at Golden Cross. The local and regulatory community has been widely represented in the Joint Venture's operating and closure plans throughout the history of the mine. Participants include: Regional and District Councillors and staff members, professional peer reviewers, environmental groups, local residents of the valley, and Iwi. This overall commitment to the project has resulted in a world-class rehabilitation program for the first modern metal-mine closure in New Zealand and we believe that collectively, the work done at Golden Cross is helping to set a standard for the success of future programs within the extractive industry.

Jan 1, 2000

By J Gresham, A Turichshev

Ore from Henderson’s 7700 Southwest panel cave is transported between the production and truck haulage levels through a series of orepasses. A typical orepass complex consolidates dump points from four production drifts into two long bored raises feeding into a single truckloading chute. The system typically covers a vertical extent of 200 m and a lateral extent of 90 m. In the process of commissioning several initial orepass complexes, challenges with preferential draw in the long bored raises were observed. Preferential draw occurs when one long orepass mobilises much sooner and/or flows significantly faster than the other orepass. This has negative implications for orepass availability in the production drifts. As future mining at Henderson relies on the construction and use of such orepass systems, the development of appropriate design criteria and practical solutions to existing flow problems was necessary.A series of PFC3D numerical models were developed to assist in identifying the factors influencing preferential draw and possible corrective measures. The models helped to identify two primary factors that caused the preferential effect: the relative elevation of the brow at the bottom of each long bored raise, and the location of the bin used to funnel fragmented rock from both raises into the chute. This paper covers the initial design of the orepass complexes at Henderson, results of the numerical models, mitigation work done to date on existing orepass complexes, and design criteria for future construction.CITATION:Gresham, J and Turichshev, A, 2016. Correcting preferential flow problems in long orepass systems at Henderson Mine, in Proceedings Seventh International Conference and Exhibition on Mass Mining (MassMin 2016), pp 549–554 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 9, 2016

By K Niiranen

Luossavaara-Kiirunavaara AB (LKAB) operates one iron ore mine, three concentration plants and three pelletising plants in Kiruna, Sweden. The current methods of separation at the beneficiation plants are low intensity magnetic separation (LIMS) and reverse apatite flotation, where the wet LIMS stage is regarded as the crucial part of silica separation from the ore. Because future silica levels are expected to increase in the incoming material to the beneficiation plants, geometallurgy has become an important area of development and research.A laboratory-scale methodology was developed for the systematic characterisation of the ore for mineral processing, with the focus on the high silica ore type B2 and newly discovered subtypes. This methodology combines mineralogical, geochemical and process mineralogical characteristics. Automated mineralogy (QEMSCAN®) is used to study the modal mineralogy, the distribution of silicate minerals in different particle size classes after comminution, the deportment of silicon (Si) between various silicates and the degree of liberation and intergrowth of magnetite and silicates. An essential stage in the systematic characterisation of the ore deposit for mineral processing is the estimation and simulation of different parameters from the laboratory scale to the full scale at the concentration plants. This is achieved by using empirical models based on the data collected at the mineral processing plants. As the first step to implement the geometallurgical information, the current geological model is reconstructed with the mineralogy and the two, newly defined subtypes of high silica ore type B2 are separated into different domains.To study the reduction of the SiO2 content in the magnetite concentrate, a large-scale reverse cationic silicate flotation laboratory test program was initiated in early spring 2016. This program investigated potential silicate flotation in the beneficiation plants at the Kiirunavaara site. The second target is to implant mineral processing parameters into the block model based on the new geological model. This information provides a good basis for making a prognosis for mine planning and a quality prognosis regarding the crude ore for mineral processing.CITATION:Niiranen, K, 2017. A geometallurgical perspective on a high-grade iron ore deposit at Kiirunavaara, northern Sweden, in Proceedings Iron Ore 2017, pp 309–318 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 24, 2017

Separation of Nickel and Cobalt from Manganese, Magnesium and Calcium by Synergistic Solvent Extraction - From Batch Tests to Pilot Plant Operation The synergistic solvent extraction system consisting of Versatic 10/LIX63/TBP was used for the separation and purification of nickel and cobalt from synthetic laterite leach solution after iron removal. Very encouraging results were obtained for separating nickel and cobalt from manganese, magnesium and calcium. In batch tests, the organic composition of the synergistic system was optimised and very large synergistic shifts for nickel and cobalt were observed. The ?pH50(Mn-Co) and ?pH50(Mn-Ni) values were as large as 1.65 and 2.40, respectively. The extraction and stripping kinetics of nickel and cobalt was fast. Semi continuous extraction tests were conducted with a pH profile of 5.5/6.1/6.5 in three stages at 40¦C. The nickel and cobalt extractions reached 99.9 per cent with only 5 mg/L Ni and <1 mg/L Co left in the raffinate. With two stages of scrubbing, only 2 mg/L Mn and less than 1 mg/L Mg and Ca were left in the scrubbed organic solution. With two stripping stages, the stripping efficiencies of Ni and Co reached over 95 per cent. A fully continuous pilot plant operation was conducted successfully for 280 hours. With an O/A ratio of about 2 and a pH profile of 5.5/5.8/6.0/6.3 for the four stages EX1/EX2/Ex3/EX4, both nickel and cobalt were almost completely extracted. Using a pH profile of 5.4/5.0 for SC1/SC2, the manganese scrubbing efficiency was over 96 per cent. Using three strip stages, over 98 per cent Ni and 99 per cent Co were stripped with only 64 mg/L Ni in the stripped organic solution. The nickel concentration in the loaded strip liquor reached 83 g/L, resulting in a ?Ni of over 28 g/L. The chemical stability of the system was also assessed over 12 weeks under proposed industrial operating conditions. Operation exclusively under strip conditions at 50¦C and 40¦C resulted in LIX63 oxime half lives of 1.1 and 2.1 years, respectively. Operation exclusively under extract conditions at 50¦C and 40¦C resulted in oxime half lives of 0.26 and 0.82 years, respectively. Losses of Versatic 10 were less than four per cent.

Sep 13, 2010

By K Gordon, A Black

Two remediation strategies have been considered to reduce the levels of acidity and dissolved metals in acid mine drainage discharging from Sullivan Mine, West Coast, New Zealand. The oxidising strategy involves adding alkalinity and dissolved oxygen (DO) resulting in the precipitation of metallic oxides and decreased acidity. The reducing strategy involves removing DO, resulting in the precipitation of metallic sulfides, followed by addition of alkalinity to decrease acidity. Field remediation trials indicate a reducing system may be more effective for this site than an oxidising system. A residence time of only two hours in the limestone layer of a successive alkalinity producing system (SAPS) is sufficient to reduce acidity by 100 per cent, iron by 71 per cent, aluminium by 59 per cent, nickel by 38 per cent and manganese by 26 per cent. The proposed remediation plan will likely include a series of SAPS, followed by an anoxic limestone drain, and settling ponds to capture any remaining precipitates.

Jan 1, 2003

By H Lemos, E Nunes, D Jacobson, R Costa, L Ono, A Alves, H Delboni Jr

Oversize rock breaking and metal tramp removal are key issues for reducing primary crusher downtime, as well as improving the safety associated with its operation. Remote operation of such tasks would thus not only increase productivity, but also reduce the risks related to work in confined spaces, fall risks, and overhead hazards. These issues are particularly relevant in high-capacity operations such as iron ore mining, where large machines are in continuous operation. This article describes the architecture, construction and advanced testing of a novel remotely operated robotic mechanism for assessment and removal of metal tramp from primary crusher chambers. The system essentially includes a robotic-arm equipped with a hydraulic clamp tool for handling oversize material, as well as an oxy-flame module for cutting metal pieces entrapped within the primary crusher cavity. The first industrial unit was delivered to a large iron ore mine in Brazil, where the installation and testing is scheduled within the coming months.

Nov 8, 2021

Economic Sustainable Power for Mineral Processing

Sep 13, 2010

The pressure of low commodity prices forced the design process for the second lift of Northparkes E26 Mine to adopt a continuous improvement philosophy. The emphasis was to minimise capital expenditure while still maintaining the excellent low operating costs achieved on Lift 1. Although the first block cave lift at Northparkes is the most productive underground mine in the world and is held up as a benchmark for the use of technology in mining, areas for improvement were identified. Every area was critically assessed and investigated for the possible application of new techniques and technologies. Key learnings from the construction and production phases of Lift 1 were captured, documented and used as the starting point for the Lift 2 design. This paper shows how and why the design parameters initially used onLift 1 were changed to become the current E26 Lift 2 developmentproposal. The main differences between the two block caves arehighlighted. The alternative techniques and equipment that wereconsidered are also discussed. * Originally published in the Proceedings of MassMin 2000,published by The AusIMM.

Jan 1, 2001

By D Craw, S Clearwater, S Hammit, C Smith

Prior to rehabilitation, plant cover on quartz gravel overburden at Wangaloa coal mine was highly patchy. Stabilisation techniques have since considerably altered the condition of the main overburden yet deposits in the east and west remain largely intact. On the eastern overburden, three distinct zones of revegetation have naturally developed: Zone 1 represents a dense plant cover, Zone 2 a patchy cover and Zone 3 a sparse cover of isolated plants. Aerial photographs show much of the eastern overburden was deposited between 1940 and 1960s. Yet we found that the temporal scale of deposition did not wholly account for the differences observed in vegetation development. To investigate other influential factors, we set up 12 study plots using four replicates in each vegetation zone. The diversity and density of plants in each plot were measured to quantify the degree of vegetation development. Samples from the substrate in each plot were collected using soil cores to a depth of 10 cm. Cores were analysed for indicators of nutrient availability, metal content and physical composition. We found that substrate chemistry varied between individual study plots, but showed little difference overall along the vegetation gradient. Substrate physical differences were much greater. The ratio of coarse quartz pebbles: fines was considerably higher in Zone 3 than other zones, and within zones where plants were not growing. Bulk density also increased successively from Zone 1 - 3. We found clear evidence for the reversed stratigraphy of excavation superimposed over the time scale of deposition, and the corresponding nature of fine particles. The rate of revegetation was therefore highly dependent upon the substrate composition of the last surface deposit from the dumping truck. Our data suggests an optimum ratio exists between inert coarse material and a fine matrix for progressive natural vegetation development on mine substrates.

Jan 1, 2004

By J Guo, K Williams, S Caldwell, W Chen

Mining is increasingly occurring near or below the water table. This has led to a higher rate of handling problems associated with increased moisture and increased adhesion, which lead to a higher rate of blockage events within the materials handling chain. Typically, these ores and minerals are known as ‘wet and sticky materials’.Currently there is very limited knowledge and/or methodologies for effective design of efficient materials handling systems when it comes to handling wet and sticky materials. However, there is one major parameter that significantly affects handleability of a wet and sticky ore; namely, its moisture content. Flow property testing has shown that when moisture is reduced, the adhesive properties of the ore are also significantly reduced, thereby increasing ore flowability.The research embodied in this paper investigates the moisture reduction rate through a loose packed bed of iron ore using dry, ambient temperature airflow. A comparison of the predictive capabilities of a proposed drying model to data obtained from on-site experiments using iron ore fines is made. Building on an assumption made by Hukill (1954), a second term has been proposed to account for rewetting effects in the drying process. From this research, identification of improved moisture reduction approaches is envisaged.CITATION:Caldwell, S, Williams, K, Guo, J and Chen, W, 2017 Aeration induced moisture reduction of iron ore, in Proceedings Iron Ore 2017, pp 455–460 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 24, 2017

The formation and distribution of gold placers in active collisional mountain belts are directly related to the tectonic, topographic, climatic and erosional constraints prevailing on either side of the orogen at the time of placer formation. In the absence of pre-existing placer deposits, these factors combine to concentrate placer development on the side of the orogen facing the prevailing winds, where most of the erosion and uplift occurs. Drainage network changes and glaciation can significantly alter placer distribution with respect to source areas within the orogen. After collision stops, placer formation will proceed on both sides of the orogen as exhumation of the mountain belt ensues. Incorporation of pre-existing placers formed on ancient mountain belts into younger placers in subsequent orogens, may be recognised by anomalous placer distribution compared to the above model. Most of the relatively young giant placers such as those inNew Zealand, Chile, Bolivia and Columbia, exhibit these general patterns. Their character and mode of formation have important implications for the formation and distribution of much older placers, such as those in South Africa's Witwatersrand Basin.

Jan 1, 1996

By D Craw, L Cox, R J. Norris

The Rise and Shine Shear Zone is a mineralised low-angle deformation zone traceable for at least 7 km through biotite zone schist of the Dunstan Range, central Otago. The zone is commonly believed to be similar to the actively mined Macraes deposit. The Rise and Shine Shear Zone occurs in the immediate footwall of the Thomsons Gorge Fault, a regional scale Cretaceous normal fault that juxtaposes chlorite zone schist against biotite zone schist. Most mineralised rocks are deformed and record a progression from early stages of semiductile deformation to more brittle cataclasis. Folds in mineralised rocks trend northwards. The mineralised schist is hydrothermally altered with variable silicification, sericitisation, chloritisation, replacement of titanite by rutile and carbonate alteration. Gold is associated with pyrite and arsenopyrite and occurs in both ductile and brittle microstructures. Sheared and mineralised schist is cut by north-striking fault zones which host mineralised quartz veins. Veins in the shear zone contain hydrothermal albite. Trace element analyses show enrichment in As, U, Th and rare earth elements. Many of the above features are similar to Macraes deposit, but there are important differences. In particular, the Macraes deposit is hosted in lower grade rocks and truncated beneath by a normal fault, Macraes has no U or Th enrichment, Macraes veins have no albite and folds at Macraes trend NW-W. Rise and Shine mineralised rocks have no Cr enrichment and no hydrothermal graphite.

Jan 1, 2005

Remote sensing, in general, is the recording of light and heat from a planet's surface within a certain range of the electromagnetic spectrum. For the Earth, systems capable of this recording are the MultiSpectral Scanner (MSS) and SLAR. The former is the recording system used in satellite and will be discussed in the next section. SLAR stands for Side Looking Airborne Radar. This device sends invisible radar waves which illuminate the Earth's surface. The reflected waves are subsequently recorded as images. The system can operate through darkness and dense cloud cover, and is particularly suited for the study of geological structures at both large and small scale (Wayland 1976). Remote sensing techniques are now widely being made use of in mineral exploration, especially for those last remote 'sanctuaries' where geological data are meagre or non-existent. For places like Borneo, West Irian, the Amazon Basin etc. remote sensing, in the form of both satellite imagery and SLAR, is of considerable help, in fact more often than not the only help, to delineate geological provinces, geotectonic domains and meaningful lineaments. In the case of New Zealand, well made geological maps at scale 1:250 000 by the Geological Survey are available to the public and these provide useful preliminary grounds for the selection of target areas. However, even in this case LANDSAT imagery can be of aid as will be shown later.

Jan 1, 1977

By S R. La Brooy, T Giraudo, I C. Ritchie

The treatment plant at the Macraes Gold Project in New Zealand processes a carbonaceous, refractory sulphide gold ore. Since its commissioning in 1990, there has been a programme of continuous improvement of the plant, leading to higher recovery, increased throughput and low operating costs. During this time, a number of processes for treating both, or either, the preg-robbing carbonaceous fraction of the ore and the refractory sulfide fraction have been evaluated, trialed and utilised. The latest phase involves the installation by Minproc of plant utilising Newmont Gold's Pressure Oxidation Technology, a process which is anticipated to mitigate both problem factors when commissioned in 1999.

Jan 1, 1998

By P Grieve, J L. Mauk

The Central Maratoto Valley in the Coromandel Peninsula contains a sequence of veins in pervasively altered dacite + andesites of the Waipupu Formation. We recognise at least eight different vein types: (1) pyrite stringers, (2) quartz + carbonate veins, (3) crystalline quartz veins, (4) carbonate veins, (5) chlorite + carbonate veins, (6) siderite veinlets, (7) siderite + carbonate veins and (8) carbonate + pyrite veins. The overall temporal trend of the veins is from early pyrite to quartz and then to late carbonate veins. Carbonate veins and pyrite stringers both form planar and irregular veins, whereas some carbonate veins have diffuse contacts with the wall rock. Gold and base metal sulphides are associated with some of the quartz + carbonate veins. Textures within the veins reflect open space filling and multi-phase reopening. A partial record of hydrothermal activity has been preserved by vein crosscutting relationships, hydrothermal alteration minerals and fluid inclusions. Hydrothermal alteration minerals display zonation from south to north. The alteration increases from unaltered to weak propylitic alteration of andesite in the south (MVRCDC1), to sericitic alteration of andesite and dacite in the north (MVRCDC3). The alteration assemblage is dominantly sericitic, with no adularia present, drawing parallels to the Thames region where there is no adularia.

Jan 1, 1999