Search Documents

Since the 1950's drilling has been rapidly mechanised. First from hand held drills with air legs to pneumatic jumbos, then to more effective hydraulic jumbos. Development of underground drilling equipment naturally could not have stopped here. Hydraulic drilling saw an improvement in drilling capacity and efficiency after the introduction of second generation drifters in the early 1980's. Also in the early 1980's a few equipment suppliers started to study how to improve the efficiency in operating the rigs. The first computerised rigs for tunnelling were delivered to work sites in mid 1980's. At the same time a few computerised longhole drills started drilling in mines.

Jan 1, 1988

The Mt Leyshon Volcanic Complex lies 24 kilometres south-west of Charters Towers and is part of a major continental volcano-plutonic province of Permo-Carboniferous age in north-east Queensland.The volcanic complex is located on the contact between Cape River Beds of Cambrian age and the Ordovician Ravenswood Granodiorite Complex. The emplacement of the complex appears to have been structurally controlled and is at the intersection of major north-east and minor north-west trending lineaments. The gold mineralisation occurs in the form of cavity coatings, matrix replacement, disseminations, and vein and fracture fillings containing quartz, chlorite, carbonate, pyrite, sphalerite, chalcopyrite and galena in various volcanic breccias and rhyolitic intrusives. The current published mineable ore reserves, calculated by Noranda Australia Limited, are 6.3 million tonnes of 1.8 grams per tonne gold and 4.8 grams per tonne silver. The orebody is open at depth, and in all directions except north where it abuts the granodiorite.

Jan 1, 1986

By Esaki M, Nishimura K

This paper describes the results of the field application tests at Miike Colliery on the integrated automatization of the longwall mining system for medium thick coal seam. The purpose of the research is to develop an automatic longwall mining system which can be controlled accurately from outside of the face, and the ultimate goal is an eliminate of men from the face. Presently, the field test is being conducted in Yotsuyama mine following to a success in the performance test on surface. Remote Batch Control System for shield supports has been adapted to operate all supports from the control panel located at the entrance of the face. Remote monitoring and control system of the drum shearer has also been tested. The system makes it possible to operate the shearer either at the main gate or full automatic. Productivity and safety will be substantially improved as those systems enable to eliminate all workers from the face under the severe working conditions with high ground pressure and hot and humid atmosphere due to increasing mining depth. So far, we have been satisfied with the results of the field test and those system will be an effective countermeasure to operate the face with a high risk of rock-burst.

Jan 1, 1987

By J T. Sharp, M A. Styler, D McGowan, P W. Mayne

Static liquefaction is a geotechnical hazard in mine tailings facilities. Soils that are contractive in shear are susceptible to static liquefaction. Tailings facilities are dynamic structures, typically growing in height each year. Dilative tailings may become contractive under increased effective stress. In this paper we show that Cone Penetration Test (CPT) data can be used to estimate the future state of in-place tailings under changes in effective stress. Susceptibility to static liquefaction is typically evaluated with the CPT by using a clean-sand equivalent normalized cone tip resistance (Qtn,cs) or by estimating the state parameter (?). An alternative approach is to evaluate the soil-state using the yield-stress-ratio (YSR = ?’y/?’v0). If the YSR equals one it is on the normal consolidation line and the soil-state is contractive. YSR values greater than three are typically dense of the critical state line (CSL) and the soil-state is dilative. In this paper we review how to calculate Qtn,cs, ?, and ?’y; and how the YSR can be used to screen for contractive soil behaviour. Unlike Qtn,cs and ?, it is very simple to estimate how the YSR will change due to an increase in overburden stress. This YSR approach was evaluated at three locations that saw increases in overburden of 10 m, 20 m, and 25 m. We show that the ?’y calculations are consistent and the increase in effective stress moves the soil state towards looser soil states. CITATION:Styler, M A, Mayne, P W, McGowan, D and Sharp, J T, 2018. Predicting changes in static liquefaction susceptibility using cone penetration test results, in Proceedings Mine Waste and Tailings Stewardship Conference 2018, pp 317–332 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 23, 2018

By M Graham, R Brunning, C Andringa-Bate, S Westergren

In 2010, Rio Tinto Iron Ore’s operations commenced the planning and design of a sampling and analysis system for the new 50 Mt/a Cape Lambert Port B (CLB) facility. Current sampling systems at the ports consist of automated robotic, mass-based sampling protocols employed at Dampier, and semi-automated, time-based sampling systems operating at Cape Lambert Port A.The new sampling system at CLB has brought together a fully automated sampling and analysis system utilising time-based sampling, with the capacity to sample ore products of medium quality variation as defined in ISO 3082 (ISO, 2009). The CLB system is required to sample at shiploading rates from 6000 t/h to 13 440 t/h and provide full load-port analysis. The sampling approach is to proportionally extend primary increments (of varying mass relative to shiploading rate) to a standard length using variable speed aero-belt conveyor systems. This enables a fixed number of secondary cuts to be achieved for all primary increment masses and to be delivered to the automated cell. The cell is required to be capable of concurrently processing four individual shipments, each containing multiple cargoes.Achieving the target sampling precision for all export cargo sizes has culminated in the planning, design and construction of the largest automated iron ore port laboratory in the world. The CLB sampling and analysis cell was commissioned in Q3 and Q4 2013. This paper discusses the sampling philosophy and commissioning outcomes.CITATION:Brunning, R, Andringa-Bate, C, Graham, M and Westergren, S, 2014. Cape Lambert Port B shiploading, sampling and analysis, in Proceedings Sampling 2014 , pp 79–90 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 29, 2014

By M Chen, Q D. Gao, Y G. Hu, P Yan, W B. Lu

The safety and stability of construction structures are often affected by blast-induced waves. Investigating the generation mechanism of shear wave (S-wave) during blasting is important, because it has a strong effect in blasting damage. In this paper the generation mechanism and verification of S-wave was studied analytically and numerically. Under the finite velocity of detonation (VOD) of cylindrical charge or the compression wave (P-wave) communicating with the interface of different media during the propagation, the generation mechanism of S-wave was analysed. Propagation of blasting wave in cylindrical charge was simulated with the elastic model, and the generation of S-wave induced by finite VOD was proved. To compare with different numerical methods in simulating the generation of S-wave, the blasting process of instantaneous detonation was simulated by using the elastic model, elastic-plastic model and smoothed particle hydrodynamics and finite element method (SPH-FEM) coupled model. Results demonstrate that the S-wave could not be found in middle section of the charge if the elastic model is employed. But when using elastic-plastic model and SPH-FEM coupled model, the generation of S-wave could be verified. Under the SPH-FEM condition, the amplitude of S-wave is larger and the arrival time difference between P-wave and S-wave is closer to theoretical results.CITATION:Gao, Q D, Lu, W B, Hu, Y G, Chen, M and Yan, P, 2015. Comparison of the generation of shear wave with different simulation approaches, in Proceedings 11th International Symposium on Rock Fragmentation by Blasting, pp 79–88 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 24, 2015

By Oda Y, Hashiuchi M

In the smelting section, flexible fuels such as coal or coke are used in place of heavy fuel oil in order to utilize energy sources more efficiently. Heat recovered from the off gas of the furnace has been converted by the waste heat boiler into steam, which is used for self power generation and for heating or maintaining various temperatures. The amount of the recovered steam in the smelter is currently increasing due to maximum utilization of powdered cokes. The heat source required to maintain the temperature of the electrolyte in the tank house is electric power and steam. However until recent year this steam was provided by its own heavy oil combustion type boiler in the tank house since the amount of steam consumed in heating the electrolyte is large. Though experimental work over the last few years has shown the advantages of reducing steam in the tank house by fully covering the cell, the implementation of the full cover can lead to other operating problems. However various improvements, mainly the covering of the cell with a simple device, have led to greatly reduced steam consumption. As a result, steam for the tank house is now provided by the waste heat boiler only bringing more efficient energy usage.

Jan 1, 1987

By Falbo A, Barbaro M, Esposito MA, Passariello B

Acidic reductive leaching is one of the best known and most widely employed chemical processes for beneficiating minerals of industrial interest. Conventional acidic leaching with sodium dithionite (Na2S2O4), employed to bleach industrial minerals used in the production of ceramics, glassware, paper etc, does not always allow products of high quality to be obtained. In the work reported here two reducing agents, ascorbic acid and oxalic acid, have been employed in a medium acidified by means of sulphuric acid. Continuous systematic tests have been performed on a kaolin sample containing 0.8 per cent Fe2O3, adopting various operating parameters such as, leaching time, temperature and reagent concentration. In each case the total quantity of bi- and trivalent iron dissolved was ascertained. Removal of 80 per cent and 100 per cent of iron with ascorbic and oxalic acid respectively was obtained, while less than one per cent of iron was dissolved in the presence of sulphuric acid only. Products having a very good degree of whiteness (92 - 94 per cent) were obtained, whereas with sodium dithionite the degree of whiteness was in the 85 to 88 per cent range. The best conditions identified were applied to a sample of quartz for the removal of ferric impurities.

Jan 1, 1993

By C Li, K McDonald an, T Nicholson, C Brown

The relative reactivities of chars prepared from different coal samples at temperatures in the range 500 to 1150¦C were determined by measuring the rates of metallisation of a standard ilmenite concentrate. The results have been interpreted in relation to different measured physical and chemical properties of the chars. Char reactivities were found to correlate with the maximum specific surface area (SSA) of the chars, obtained from plots of SSA versus temperature. Weathering of coal samples gave higher reactivities which correlated with higher SSAs. Experiments using recycled chars showed that the high internal SSAs developed during earlier reduction reactions provide no benefit in terms of increased metallisations. The important role of char hydrogen contents in controlling low temperature metallisation rates was demonstrated. Chars prepared from different rank coals had the same hydrogen content when prepared at the same temperature. Ilmenite metallisation rates had a linear dependence on the hydrogen content of the chars. Large differences in the slopes of the metallisation versus H2 content curves for different chars were interpreted in terms of SSA variations and catalysis of the gas reactions by dispersed metallic iron particles in the chars. A simple test based on magnetic separation of the char was shown to give an indication of enhanced reactivity due to contained metallic iron.

Jan 1, 2001

The Kalgoorlie Golden Mile is proposed as an Archaean volcanogenic-type deposit, modified and redistributed along later-developed structures. Rich pyritctelluride and Green Leader gold mineralization is associated with the end phase of basic volcanism and, in a general sense, is confined to a broad interface zone between the products of marine basic volcanism and later acid volcanism. There is virtualIy no ore associated with the main body of acid volcanics.Green Leader is the local name of a type of ore that occurs at some igneous rock contacts in association with graphitic sediments and layered acidic tuffs. It is characteristicalIy green, of various shades, and commonly yields very high gold assays, the reasons for which are not apparent in hand specimen.Carbonates, carbonaceous shales, tuffites, rich gold ores, and acid and intermediate dykes, alI indicating a common heritage, are features common to the main ore hosts, viz. the Paringa Basalt (Calc Schist) and theGolden Mile Dolerite ("Quartz Dolerite Greenstone").Several probably related fracture systems have reconstituted most, but not all, of the original deposits into a large number of steep tabular lodes.Includes two sets of discussions and comments from later Proceedings volumes.

Jan 1, 1974

By G B. Douglas

Lime-based neutralisation has long been the remediation treatment of choice for acidic mine pit waters. While suited to the attenuation of acidity, lime-based neutralisation may be difficult to implement efficiently due to variation in quality and the partial loss of neutralisation efficiency due to armouring. Large volumes of gypsum-bearing sludge may also require mechanical dewatering and transfer to final voids prior to resumption of in-pit mining or closure. Thus, operational costs may be substantially higher than primary neutralisation alone. Lime production also results in large greenhouse gas (CO2) emissions.Hydrotalcites (HT) are a class of Mg-Al layered double hydroxide minerals with the composition Mg6Al2(CO3 )(OH)16.4H2O. A range of other divalent and trivalent cations may also readily substitute for Mg (eg Cu, Ni, Pb, Zn), Al (eg Fe, La, Ce) and metalloids/oxyanions (SeO42-, AsO43 -/CrO42 -, MnO4-) for CO3 into the hydrotalcite structure. A common feature of acid mine pit waters, often overlooked in assessment of potential remediation options, is the frequent predominance of divalent and trivalent cations as a consequence of partial decomposition of both ore and gangue minerals during in-pit wall rock leaching. Thus, given the presence of substantial divalent and trivalent cations in acidic mine pit waters, an opportunity exists to exploit and in effect work harmoniously with the prevailing pit water composition to form a polymetallic hydrotalcite.The utility of hydrotalcites in the remediation of acidic mine pit waters lies in their ability to incorporate a wide range of contaminants; instantaneous formation, often in a single step; simple post-treatment solute composition; rapid settling; low sludge volume; and the potential to form ore-grade precipitates potentially amendable to reprocessing to (partially) recover remediation costs. Examples of hydrotalcite formation as a method to remediate contaminated acidic mine pit waters at laboratory-scale to full-scale will be presented.CITATION:Douglas, G B, 2015. Whither lime? In situ hydrotalcite precipitation as a method of remediation for acidic mine lakes, in Proceedings Tailings and Mine Waste Management for the 21st Century , pp 97–104 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 27, 2015

By M I. Pownceby, M A. Rhamdhani, S Purohit, G Brooks

The current practice of magnetite ore agglomeration involves high temperature oxidation roasting (typically at 1200–1350°C) of magnetite to hematite phase in order to improve the strength and reducibility of pellets. The requirement to pre-oxidise the magnetite before introduction to an ironmaking plant increases the CO2 emissions generated during the ironmaking process. In our previous papers, a novel, alternative agglomeration route for magnetite ores was presented where magnetite was converted to a reducible CaFe3O5 (CWF) phase through the addition of lime to produce a Lime-Magnetite Pellet (LMP) feedstock that can be directly charged to ironmaking units. The LMP process eliminates the magnetite oxidation stage, thereby reducing the CO2 emission during ironmaking. The concept was tested by thermodynamic calculations, high temperature experiments and scaled-down pilot scale test work. In this paper, larger scale synthesis of halfstoichiometric LMPs (1 mole of Fe3O4 and ½ mole of CaCO3) were prepared using a balling drum, followed by overnight drying at 110°C and induration at 1050°C for two hours. The LMPs were analysed using X-Ray Diffraction and Scanning Electron Microscope techniques for phase and microstructure characterisation. The LMPs were found to have 14–15 wt. per cent of CWF phase when indurated under a CO2/CO ratio of 8.5:1. Pilot scale testing of the LMPs was conducted following ISO standard test procedures. The test results indicated the LMP’s had a Reducibility Index (RI) of over 91 per cent, a Tumbler Index (TI) of 87 per cent and a Reduction Degradation Index (RDI) of 4.6 per cent. The results indicate LMPs may be useful as an alternative feedstock to ironmaking processes that would result in lower overall CO2 emissions.

Nov 8, 2021

By Ramani R. V

There are many important physical phenomena in mine ventilation which involve transient mass and heat transfer processes. These processes have been modeled using differential equations often solved with close form solution. Within the last two decades, many numerical schemes have been devised to solve these mass-transfer problems. Much of this effort has focused on variants of the finite element and finite difference methods. In this paper, the solution of mass transfer models in mine ventilation by finite difference technique is discussed. Specifically, the computational effort and the accuracy of the solution are presented.

Jan 1, 1988

Polish coal mines are well equipped with methane monitoring systems,nevertheless the worsening conditions force a continuous impro- vement in the field of environmental monitoring. Application of modern electronic components make it possible to design the new modular telemonitoring system incorporating the best features of the older systems,widely employed in Polish collieries, eliminating their weak points. Several new sensors and portable instru- ments for methane monitoring and early fire detection have been developed and tested in mining conditions.

Jan 1, 1988

By A D. Pradana, D R. Pradana, Y H. Putra, Z Zulhan, T Hidayat

The high temperature processing of nickel laterite ore is currently dominated by the Rotary Kiln- Electric Furnace (RKEF) technology. The ratio of SiO2/MgO (S/M) in the ore is one of the critical parameters that determines the success of the RKEF process. Incompatible S/M ratios in the ore can cause aggressive chemical interaction between the slag and MgO refractory. The slag-refractory interaction at conditions relevant to nickel laterite ore smelting was investigated in the present study. Synthetic mixtures representing the slag compositions of nickel laterite ore smelting were prepared by mixing MgO, SiO2, Al2O3, CaO, Fe2O3, and Fe and heating the mixtures in steel containers at 1300°C under an argon atmosphere for 3 hrs. Pure MgO crucible were used as containment material in the melting process of the mixtures to represent the MgO refractory. The kinetics of the slagrefractory reaction were investigated using samples with selected initial S/M ratios of 2.0 and 3.0 (wt/wt) (with constant CaO = 3 wt per cent, Al2O3 = 5 wt per cent, FeO = 10 wt per cent) by performing melting at 1500°C in MgO crucibles for 5, 30, and 120 mins under an argon atmosphere. The effect of the S/M ratio in slag on the slag-refractory interaction was also investigated by performing melting of mixtures with different initial S/M ratios of 1.75, 2.0, 2.5, and 3.0 (wt/wt) in MgO crucibles at 1500°C for 120 mins under an argon atmosphere. After the melting process, each sample was quenched in water, mounted in resin, ground, polished, and coated. The interaction between the slags and MgO refractory was then evaluated by analysing the polished samples using a scanning electron microscope equipped with an energy dispersive spectroscopy (SEM-EDS). Thermodynamic simulations using FactSage™ 8.0 thermochemical software were performed based on the experimental slag compositions, refractory, and conditions to support the evaluation process. The results show that a higher S/M ratio in slag leads to a higher tendency for the refractory component to dissolve into the slag. A higher S/M ratio in slag also leads to an increasing extent of solid-state diffusion of iron oxide into the remaining refractory grains. The dissolution of MgO into the slag is rapid; the MgO concentration in the final slag increased by 2.4 wt per cent and 5.7 wt per cent at initial S/M ratios of 2.0 and 3.0 wt/wt, respectively, within 5 and 30 mins of the melting process.

Aug 21, 2024

By M Ind, B Usher

Environmental regulators are increasingly adopting risk-based approaches to protect aquatic ecosystems. The Australian and New Zealand Environment and Conservation Council (ANZECC) and the Agriculture and Resource Management Council of Australia and New Zealand (ARMCANZ) (2000) introduced a risk-based approach to water quality guidelines that use decision frameworks to adapt water quality guidelines to local environmental conditions. Environmental quality objectives are no longer a simple ‘pass or fail’ number such as restricting total suspended solids (TSS) concentration to a specified limit for a particular rainfall event. This approach ignores spatial and temporal variability and the complexity of aquatic ecosystems. The risk-based approach establishes levels where adverse effects may occur. If these objectives are not met, further risk-based investigation is undertaken to assess the potential impact to the ecosystem. Klohn Crippen Berger (KCB) developed a dynamic simulation to predict the variability of sediment discharges, which is applicable for risk-based impact assessment of aquatic ecosystems. The application of the methodology over the life of a mine site is illustrated using a proposed South Pacific mine.The site location is in extremely rugged terrain with a high annual rainfall of approximately 4.7 m. There were two major sediment ponds proposed to reduce sediment discharges. A sediment and hydrology model was developed in Goldsim to provide daily estimates of run-off flows and sediment concentrations. A modified algorithm based on the Australian water balance model was created and incorporated into the Goldsim model and calibrated using recorded field data.The sediment module was developed based on a Revised Universal Soil Loss Equation (RUSLE) assessment, an annual prediction of soil loss over a catchment. A land-use type erosion vector was developed for different land-use types and for each of the subcatchments, a subcatchment erodibility vector was calculated. This vector and the daily rainfall erosivity factor were used to estimate the daily soil loss. The estimated soil loss and the modelled run-off yielded predictions of daily sediment concentrations. Finally, a sediment settling module was used to predict the daily efficiency of the sediment ponds and hence discharged sediment concentrations.The results of this modelling form the first part of a quantitative risk-based assessment into suspended solids impacts. The second part is the assessment of the effects of these predicted TSS concentrations on aquatic ecology. As part of the feedback-loop required in a risk management framework, if the environmental quality objectives are not met then further management decisions and actions may be required to reduce the risks presented by suspended solids. This may include modifications to: the mine-development plan; construction techniques and scheduling; processing techniques; rehabilitation strategies; or hard-engineering solutions such as sediment basins or flocculation.The Goldsim water-balance model provides a quick and efficient method of testing potential remedial actions on predicted sediment loads and concentrations. In combination with a cost-benefit assessment, options for reducing sediment releases from the mine site can be effectively and quantitatively compared thereby providing mine operators with a basis for decision-making. Regulators can also be satisfied that potential impacts to aquatic ecology have been comprehensively assessed and the necessary management decisions have been initiated to limit risk to the environment.CITATION:Ind, M and Usher, B, ?2014. A dynamic sediment simulation to predict the variability of suspended solids concentrations over life-of-mine for application to a risk-based environmental assessment, in Proceedings Life-of-Mine 2014 , pp 191–204 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 16, 2014

By E M. Gama, L Resende

The tailings are waste from mineral processing operations. The type of tailings of iron ore processing are classified into sandy tailings and mud. Already the overburden are showing significant levels of useful mineral. Both iron ore`s waste have in your composition phyllosilicates/clay that indicates the potential for use in niche markets as paving and cement. According to several studies, there are various technologies in bench and pilot levels that could be used on a large scale but there is not an economic environment, tax, regulatory and tax set. Many of these technologies are associated with the reuse of tailings and overburden in construction. All these factors influence for that so many initiatives remain in search formats and cannot advance to the new business format. There is no way to set goals of reuse of this waste, as already occurs in China, if there is not a fiscal, tax and economic structure to support such measures. The way to foster and ensure that reuse of tailings and overburden is an incentive for promoting a culture of circular economy that would allow the emergence of an ecosystem between the private, public and Government sectors with the objective of accelerating and subsidize the entire network of reuse of this waste. The closure of the mine could be the tool used to ensure and boost this ecosystem of reutilization to align it with the vocation of the area of the mining law. Following this model, the end of the mining activity could provide a financial return to the local population, a more effective environmental compensation and a reduction in costs related to the closure of the mine. In this study are shown how the Vale is working in the reuse of tailings and overburden.CITATION:Resende, L and Gama, E M, 2018. The challenges of the reuse of tailings and overburden, in Proceedings Mine Waste and Tailings Stewardship Conference 2018, pp 117–125 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 23, 2018

By J Zhang, L Klemettinen, A Jokilaakso, J Biswas, J Partinen, H O’Brien, A Klemettinen

Waste lithium-ion batteries (LIBs) are important secondary sources of many valuable materials, including Critical Raw Materials (CRMs) defined by the European Union (EU): lithium, cobalt, manganese, and graphite. Additionally, LIBs typically contain nickel and copper, which are classified as Strategic Raw Materials for EU since 2023. In recent years, great effort has been made to develop efficient recycling processes for waste LIBs. Pyrometallurgical processes have been essential in industrial production of metals for many decades. These technologies are relatively mature, with high adaptability for different raw materials. Pyrometallurgical treatment in LIB recycling typically involves the use of smelting processes, in which waste batteries are heated above their melting points and metals are separated through a reduction reaction in the liquid phase. Through this recycling route, cobalt, copper, and nickel can be efficiently recovered in the form of a metal alloy, whereas lithium and manganese are lost in the slag phase. The goal of this work was to increase the recoveries of valuable battery metals through a combination of hydro- and pyrometallurgical unit operations. First, industrial Li-ion battery scrap underwent a selective sulfation roasting stage, where the aim was to transform LiCoO2 and Mn-oxides into Li, Co and Mn sulfates. After roasting, the battery scrap was leached in distilled water with a solid to liquid ratio of 100 g/L at 60°C and recovered 95 per cent of Li, 61 per cent of Mn and 35 per cent of Co. After leaching, the solid leach residue was mixed with industrial Ni-slag and biochar, followed by reduction at 1350°C in argon atmosphere. The high-temperature smelting experiments were conducted as a function of time (5–60 mins) to investigate the reduction behaviour of battery metals. The results show that Co and Ni from the slag and leach residue can be efficiently recovered in the slag cleaning stage.

Jun 19, 2024

In seeking to improve the economic performance of mines, the management or human aspects are usually seen to be quite seperate from, and more significant than, the technical aspects. There are obvious aspects of industrial relations, man-management, skills training and supervision that are currently the focus of efforts to improve the productivity and quality of the mining process. However technology also has a lot to offer. Analysis of the costs involved suggests that innovations leading to improvement in the productivity of the excavation and transport of overburden and the recovery of coal (both in the mine and preperation plant) can lead to improvements in the economic performance of a mine that may outstrip the obvious non-technical or management opportunities for improvement. While there are some innovations currently being investigated within the industry that relate to the design of mining equipment, the type of machinery being used in open cut mines has not changed dramatically over the last twenty five years. It is also likely that mining equipment will remain essentially of the same form in the forseeable future. If significant improvements to mining performance are to be achieved other than by futher increases in the scale of machinery, then we need to seek ways to operate these same types of machines in a more productive and controlled manner. This paper discusses the identification of mining processes the improvement of which is likely to have a significant effect on mining costs and performance. Some areas of current research are discussed and potentially fruitful areas for future development are identified.

Jan 1, 1991

By Alexander RB, Hollis AJ

The magnitude of the payloads carried by mine haul trucks can have a strong influence on the mine production rates and costs. Consequently control of truck payloads is highly desirable, but in many mines the unavailability of means for measuring payloads reliably, accurately and easily has resulted in a low level of control over truck payloads. Consideration is given to two techniques which are applicable to the measurement of payloads carried by mine haul trucks, namely truck weighing and direct measurement of payloads with truck based systems. Accuracy assessments for two types of truck weighing platforms and two prototype truck based direct payload measurement systems are provided. Results show that weighing platforms based on hydraulic components have proved inadequate, while strain gauge type weighing platforms can estimate payloads to within 2% of true payload when installed, maintained and used correctly. The assessment of the two prototype truck based direct payload measurement systems shows that a high proportion of payloads were estimated to within 5% of the payloads derived from accurate weighing platforms and that these systems appear to have the potential to provide convenient and accurate measurement of payloads. This should enable payloads to be much better controlled than has been possible to date. Predictions of the effect of payloads on production rates and some components of truck haulage costs are possible and some typical results are presented. Accurate prediction of the effect of payloads are not yet possible for some major components of truck haulage costs.

Jan 1, 1986