Search Documents

By G R. Hancock, M J. Saynor, J B. C Lowry, K G. Evans, M Narayan

Tools such as landform evolution models (LEMs) provide a means of predicting how a landform may evolve over extended periods of time. Here, we utilise the CAESAR-Lisflood LEM to assess a proposed rehabilitated landform of the Ranger Uranium Mine in the Northern Territory of Australia (Figure 1). The environmental requirements for the closure of the mine state that the final landform must be able to physically isolate tailings material from the environment for a period of at least 10,000 years (Australian Government, 1999). However, uncertainty exists as to the reliability of model predictions representing thousands of years.In this study, we use model predictions from an undisturbed pre-mine landform to calibrate the parameters used in model simulations of a post-mining rehabilitated landform over a simulated period of 1,000 years. Specifically, we vary environmental conditions such as rainfall, presence/absence of vegetation and surface particle size characteristics in a series of model simulations to determine their impact on the respective landforms, to revise model input parameters as required. A simulated period of 1,000 years was used as it represents a period in which long term landform evolution patterns and trends may be established and identified. CITATION:Lowry, J B C, Narayan, M, Evans, K G, Saynor, M J and Hancock, G R, 2018. Using an undisturbed landform to calibrate long-term predictions of the evolution of a rehabilitated landform, in Proceedings Life-of-Mine 2018, pp 133–137 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 25, 2018

By Lawson F

Chrome chemicals are commercially produced by the alkali roasting of chromite ores with sodium carbonate. Results of tests conducted in a laboratory furnace indicated that the sodium carbonate reacted rapidly with part of the gangue material to form a metastable intermediate that later reacted further with the chromite. For the conditions used, the recovery of water-soluble sodium chromate was able to be described empirically as yield % = a tn with a = 0.24 T - 241.3; n = 3.90 - 3.12 × 10-3 T and t is the reaction time in hours.The major rate limiting step in the overall reaction sequence appears to be the rate at which oxygen can get to the reaction sites across the liquid film coating the solid reactants.Sodium sulfate alone was found to be an unsatisfactory source of alkali for reaction with chromite. However when limestone also was added in quantities sufficient to allow the reaction CaCO3 + Na2SO4 + H20 ? Ca SO4 + 2NaOH + CO2 to take place, the results obtained were comparable to those found when sodium car-bonate was used.For chromite particles in the size range -124 + 105 µm, the use of stoichiometric excess of sodium carbonate did not appear to increase the yield or the reaction rate significantly. However, with smaller sized particles, - 53 µm, increased yields of water-soluble chromate were obtained when roasted with more than the theoretical quantity of sodium carbonate.

Jan 1, 1984

By C Harrison, A Bowskill

The Ambuklao hydroelectric dam was originally constructed in the 1950s in the remote and mountainous region of the northern Philippines. Following its construction the dam has suffered heavily due to siltation and a partial collapse of the intake structure due to a 7.8 magnitude earthquake that struck the region in 1990. Between the years 1990 and 1999 the power station progressively lost its capacity to generate power. In 1999 the owner took the power station out of commission. The power station remained idle over the next 12 years. In 2008 the power station was sold to a new owner who commissioned the rehabilitation works.The rehabilitation project restored the operating status of the power station in June 2011 and increased its capacity from 75 MW to 105 MW. The civil contract of the rehabilitation project required the construction of a new intake structure behind an in situ rock coffer dam on the edge of the existing reservoir, new 6.2?m diameter × 124?m deep blind sunk shaft behind the intake structure, which connects to a new 6.8?m horseshoe profile headrace tunnel that ultimately connected onto the existing vertical penstocks which feed three No 35 MW Horizontal Turbines rated at 155?m head.The unique challenge in rehabilitating this existing hydropower station involved finding solutions that would conclusively deal with the challenging geological and hydrogeological conditions associated with excavating new tunnels and a drop shaft beneath a live dam.McConnell Dowell was awarded the civil works package for the rehabilitation works in August 2008. The Ambuklao rehabilitation program took 33 months to complete.Over 600?m of tunnels were excavated in highly weathered and often challenging geotechnical conditions via drill and blast with the extensive use of high-pressure fissure grouting to control groundwater ingress that was surcharged by the dam.This paper focuses on the use of high-pressure fissure grouting that took place to enable the excavation of the new waterway system and intake structure.CITATION:Bowskill, A and Harrison, C, 2014. High-pressure fissure grouting for drill and blast tunnelling, Ambuklao, Philippines, in Proceedings 15th Australasian Tunnelling Conference 2014 , pp 141–152 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 17, 2014

By D Lozada, A Salazar

Geometallurgy is a tool that, for more than a century, has been present in the implicit operations of mineral beneficiation. There’s a need to understand the characteristics of the material to be processed. This has led metallurgists to ask geologists what type of rock and mineralogy is entering the Beneficiation Plant and vice versa. The geologist needs to understand the beneficiation process in order to be able to carry out the production programming. The paradigm is whether geometallurgy can be applied to small-scale mining or if it is only aimed at large companies that invest millions of dollars to conduct studies. With this work, we provide an example of how geometallurgy can help improve the processes of a small mining company located in Ecuador (South America). We performed characterizations of geological and mineralogical and metallurgical tests in universities and the National Research Institute of Geological Metallurgical Mining. The origin of the theme is based on the fact that gold has been detected in the final tailings. The flotation concentrates meet the standards in terms of the content of economically profitable metals, but this isn’t the case with regards to the percentage of arsenic, which has hindered sales. The hypothesis is: conducting technical and scientific research will optimize the metallurgical process for the recovery of gold and concentrates. The referential framework is the mining geology of the Bella Rica District, current status of the Beneficiation Plant. In the theoretical framework there are parameters of the veins, comminution operations, gravimetric concentration, flotation, and cyanidation. The methodological framework contemplates the characterization of the gold ore, the chemical, mineralogical, textural, metallurgical analysis and the interpretation of the results. Thus, the design of a geometallurgy model of the deposit, with its main characteristics, is a conclusion that serves as a basis for the proposal of the optimization of the metallurgical process.CITATION:Lozada, D and Salazar, A, 2018. Geometallurgy applied to small-scale mining: a case study, in Proceedings 14th AusIMM Mill Operators' Conference 2018, pp 153–162 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 29, 2018

Longhole open stoping was introduced in the zinc-rich 'B' lode at New Broken Hill Consolidated Limited (NBHC) during 1968. Since then one longitud- inal and a series of transverse longhole open stopes have been developed. The longholes are drilled using Gardner Denver airtrac drilling jumbos and the broken ore is loaded from drawpoints and transported to chutes using Wagner ST5 scoop- trams. The holes were drilled from sill stopes 160 ft apart. The width of an emptied transverse longhole stope was successfully widened by blasting rings of blastholes drilled parallel to the stope wall. Proposed stope and pillar designs for a series of transverse longhole open stopes were assessed using a method of finite element analysis, applied to a longitudinal section through the area. Blastholes have been surveyed for dip and bearing using an Eastman borehole survey camera. The data produced has provided the basis of a study of blast- hole deviation. Deviation of boreholes is considered to be the major cause of the formation of benches in longhole stopes.

Jan 1, 1971

By L C. P J Fonteneau, B Godel, E R. Ramanaidou

The Hamersley Province in Western Australia hosts large iron ore deposits. Each deposit displays various iron ore types that were defined on their metallurgical properties, especially in terms of porosity and mineralogy. Conventional porosity and mineralogy information on iron ore types are provided on 2D thin sections using automated image analysis with scanning electron microscopy (SEM)-based techniques combined with chemical analyses. However these techniques cannot accurately quantify the 3D porosity. High-resolution X-ray computed tomography (HRXCT) is a non-destructive technique providing a 3D image of the sample with a resolution close to 0.5 - 0.7 ¦m for samples size of up to few centimetres in length. 3D image analysis using customised algorithms now provide accurate quantitative porosity and mineralogy of iron ore types.CITATION:Fonteneau, L C P J, Godel, B and Ramanaidou, E R, 2013. Application of high-resolution x-ray computed tomography to iron ore characterisation, in Proceedings Iron Ore 2013 , pp 243-250 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 12, 2013

By R Dunne, G Lane, S Ha, D Dreisinger

The paper outlines the 17 Mt/a Telfer Project plant process design from sample selection to feasibility study design. The 366 Mt Telfer mine reserve consists of a diverse range of copper and gold mineralisation, from massive sulfide reef ores to stockwork ore, oxide copper minerals to chalcopyrite, siltstone to competent quartzite, all with relatively high levels of gravity recoverable gold. The complexity of the orebody demanded a flexible plant that could recover copper and gold values by a combination of gravity recovery, flotation and concentrate leaching. The demands of treating ore from a high grade underground mine and a variable grade open pit (that includes underground old mine workings) necessitated a dual train approach from primary crushing to concentrate production in order to minimise the requirement for campaigning of different ore types. An extensive sampling, testwork and technical evaluation program was undertaken to identify processing characteristics and the optimum process route for each ore type. The design experience included: the development of robust primary stockpiling and pebble crushing concepts; detailed review of scale-up of SAG and ball mill pilot plant data to plant scale; the selection of two 15 MW SAG mills and two 13 MW ball mills for the grinding circuit; and detailed modelling of the pyrite concentrate carbon-in-leach (CIL)/sulfidisation acidification recovery thickening (SART)/acidification volatilisation recovery (AVR) process to optimise design for copper and cyanide recovery from leach liquors. The Telfer plant design also measures the development of process design based on experiences at the Cadia Hill Cu/Au concentrator, commissioned in 1998. The differences between the two plants are compared and contrasted.

Jan 1, 2003

By A Horn

Mineral processing is characterised by a constant adaptation to changing raw materials and market conditions. It is the link between the mined raw material and a marketable product. As a lot of high-grade reserves are exploited, a steady deterioration of raw material quality can be observed. At the same time, the customer’s requirement for product purity and consistent quality increases.Over recent years beneficiation techniques for iron ore fines have become more important in order to achieve a maximised utilisation of ore resources and to produce competitive products according to international standards.Many high capacity iron ore beneficiation plants that target the production of fines focus on gravity separation processes using fluidised bed classifiers and spirals or wet high intensity magnetic separators as an alternative. This paper demonstrates the suitability of utilising the allflux® two-stage fluidised bed classifiers to treat iron ore particles up to 2 mm in size as well as showing how the high capacity gaustec® wet high intensity magnetic separation (WHIMS) technology offers several advantages compared to other WHIMS technology.The combination of the allflux® and gaustec® technologies offer the following benefits:The two-stage fluidised bed classification extracts a significant amount of concentrate from the feed. This in turn reduces the feed capacity required for the gaustec® WHIMS located downstream.The second classification stage produces a -0.5 + 0.1 mm product and a -0.1 mm product. The efficiency of the magnetic separation on these classifi ed products is high due to optimised settings for each size fraction.

Jul 11, 2011

By T Kilpatrick

Managing heat stress on Australian mine sites is a complex and enduring challenge due to the combined and variable contribution of environmental conditions, physical activities, and protective equipment. Inappropriately managed, heat stress can place significant physical strain on workers, leading to serious and chronic health issues. Additionally, excessive heat stress can dramatically reduce productivity, with 30 per cent of workers reporting a loss of productivity due to occupational heat strain. In Australia, due to increased absenteeism and reduced work performance, heat strain is estimated to have an annual economic burden of over $8 billion.

May 5, 2022

By E Bouchard March, F Lavoie, B Legare, K Bourassa

Quebec Iron Ore (QIO), a subsidiary of Champion Iron Limited (Champion), completed the restart of the Bloom Lake iron ore mine located in the heart of the Labrador Trough region of Northern Quebec, Canada in February 2018. Prior to its restart, the concentrator flow sheet underwent major upgrades which brought the iron recovery to the highest of all Labrador Trough operations. After two profitable years of production, QIO, supported by Soutex, started to look at technologies to improve its current performance and integrate into its expansion project flow sheet. From the lessons learned while optimising Phase 1, the addition of a scavenger-cleaner processing stage was identified as an improvement opportunity to increase recovery, produce a higher-grade product, and further improve the stability of concentrate quality. In 2019, the NI-43101 feasibility study for the Phase 2 expansion, aiming to double the production of high-grade iron ore concentrate, was published. Based on the metallurgical test work, the hydraulic classifier was selected to perform the scavenger-cleaning duty for its well-established performance and known behaviour at the cleaning step in the Phase 1 plant. To validate laboratory results, a pilot scavenger-cleaning hydraulic classifier was installed in Phase 1. Although the hydraulic classifier was selected for the feasibility study, metallurgical test work performed with the REFLUX® classifier showed interesting potential. It was thus decided to also install a pilot RC300 Reflux classifier at the scavenger-cleaning stage in Phase 1. Despite their apparent great similarities, the metallurgical performance was significantly different, and many dozens of sampling campaigns highlighted the different performance of both pieces of equipment considering the feed material particle size. This article presents the pilot plant results in terms of recovery, selectivity and stability for both the Reflux classifier and the hydraulic classifier operated in a scavenger-cleaner stage at the Bloom Lake iron ore concentrator.

Nov 8, 2021

By J Zhang, O Ostrovski, C Zhang D Cai, Q Wang

The conventional CaO-SiO2-based mould fluxes are not suitable for high-Al steel casting because of the strong reaction between silica in the flux and aluminium in the steel strand. In the process of casting of high-Al steel, flux composition changes; with the decrease of the silica concentration and increase of alumina. Knowledge and understanding of the effect of the Al2O3/SiO2 ratio on flux structure and properties are useful for flux design for the high Al-steel continuous casting. This paper investigated the effect of the Al2O3/SiO2 ratio on structure, viscosity, phase composition of fluxes quenched at different temperatures and heat transfer of CaO-Al2O3-SiO2-B2O3-Na2O-Li2OMgO- F fluxes. It was found that flux melting temperature increased with the increase in Al2O3/SiO2 ratio. Viscosity of the flux melts increased significantly with the increase of the Al2O3/SiO2 ratio from 0.7 to 1.2, reaching the maximum value, and then decreased with further increase of the Al2O3/SiO2 ratio. Raman spectroscopy analysis revealed that the change of the Al2O3/SiO2 ratio led to the change of aluminate and silicate structural units. The turning point for viscosity was attributed to the change in the degree of flux polymerisation. X-ray diffraction (XRD) analysis showed that increasing Al2O3/SiO2 ratio increased crystallisation tendency of the fluxes. Heat transfer measurement by infrared emitter technique (IET) revealed that increasing Al2O3/SiO2 ratio led to the decrease in heat flux which is correlated well with the increased crystallinity of the flux. The results suggested that the flux with Al2O3/SiO2 ratio 4.3 is the best candidate among the studied CaO-Al2O3-based mould fluxes for casting of high-Al steel.

Aug 21, 2024

By S L. Barbour

Measurement of the net percolation from the base of a cover system into the underlying waste material is a key component of a cover system monitoring program. The units of measure (ie a percentage of precipitation or rainfall) are simple to understand for all stakeholders, which increases the importance of obtaining representative net percolation values. In general, lysimeters are used to measure net percolation across the cover material-waste material interface; however, the design of lysimeters for cover system monitoring programs in the mining industry have typically not considered fundamental aspects of lysimeter design. Lysimeter design is typically thought of as being conceptually simple, when in reality the design, installation, and operation of lysimeters is often counter-intuitive, due to the complexities of flow through unsaturated soil systems. This paper puts forward a methodology for lysimeter design while also presenting the fundamental design variables that should be considered. Lysimeter design for differing climates, cover materials, and waste materials is discussed. Finally, the performance of lysimeter designs previously installed in the field at sites in Australia, Canada, and the United States are subjected to numerical modelling to determine whether net percolation is being measured properly.

Jan 1, 2003

By J E. Wajon

This paper discusses the background, requirements, need and content of plans for management of drinking water self-supplied to mining-related operations, including construction camps, especially in remote areas of Western Australia. The paper discusses the importance of cooperation between regulators, the mine site operator and the consultant in preparing a plan fully compliant with the Australian Drinking Water Guidelines to protect the quality and safety of drinking water supplied to mine sites. The paper outlines some of the issues that need to be addressed in preparing a drinking water quality management plan, such as hazard identification, risk assessment, the multiple-barrier approach and the concept of critical control points. Data requirements, monitoring, incident management, training and reporting are also covered.CITATION:Wajon, J E, 2013. Drinking water quality management for mining operations in Western Australia, in Proceedings Water in Mining 2013 , pp 321-328 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 26, 2013

By R K. A Taylor

The growth in production of beneficiated ilmenite products has been one of the most significant trends in the titanium feedstock industry over the past 30 years. In this period, the production of titanium slag and synthetic rutile has grown five-fold to the point where these products represented 56 per cent of total feedstock production in 2000. Additional production capacity is being proposed as the core component of new feedstock supply projects presently under consideration. A high proportion of these products is based on technologies for which the inherent quality of the is an essential factor. Location specific factors also play a large part in determining the cost of production. As the demand for such products grows, and the availability of favourably located sources of ilmenite of suitable quality declines, it can be expected that existing beneficiation technologies will become increasingly constrained. Existing beneficiation technologies, and those which have been developed, but are not yet commercially applied, are reviewed. Future issues which are likely to impact on the cost effectiveness of these technologies, or the quality of final products, are identified. These factors suggest directions for development of ilmenite beneficiation technologies to achieve economic production of the quality of feedstocks which will be demanded by the TiO2 pigment industry in the future.

Jan 1, 2001

By I Grewal, M Lundt

Dense medium separation (DMS) is one of several preconcentration methods used for early waste rejection from run-of-mine ores at relatively coarse particle sizes prior to additional milling and beneficiation. DMS has been used extensively in the coal, diamonds, mineral sands, base metals and iron ore industries to produce either a final product or as a preconcentration step. Laboratory scale and pilot test work at the Met-Solve laboratory in Canada has demonstrated successful separation and upgrading of other minerals such as lead, zinc, copper and lithium based ores using DMS.This paper reviews historical dense media systems, results from the pilot-scale multi-stage DMS Separator “Condor” system, as well as production plants and associated laboratory heavy liquid separation (HLS) test work on various minerals. The mineral systems tested included a lithium bearing ore and a fluorspar ore. Other minerals were tested but are not reported in this paper.Pilot plant test work on a fluorspar ore showed that 41.6% of the mass could be rejected to the tailings stream while 95.3% of the CaF2 was recoverable to the product stream. On a spodumene sample that was tested, it was possible to reject 55% of the mass to tailings while recovering over 90% of the lithium.In recent market conditions and with the decreasing grades in existing ores, preconcentration should be a consideration to maximise the value of certain operations.CITATION:Lundt, M and Grewal, I, 2017. Dense media separation – a valuable process for preconcentration, in Proceedings MetPlant 2017, pp 122–130 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 11, 2017

By J Northfield, L Neesham

The GRE46 Underground Project lies beneath the environmentally unique and culturally endowed shore of Lake Cowal. The ore body is open both along strike and at depth and is currently defined to a strike length of 1.5km and depth of 800m. The Warraga exploration decline commenced in March 2019 and represents the first stage of the Project, which is expected to underpin production at Cowal Gold Operations (CGO) for a period exceeding 10 years. Mining operations at Cowal commenced in 2005, following a period of over 20 years of exploration and permitting. In 2015 Evolution Mining (Cowal) Pty Limited (Evolution) acquired the operation from Barrick Gold Ltd (“Barrick”). Barrick had a life of mine plan that anticipated a cessation of operations in 2024 at a processing rate not exceeding 7.5 Mtpa. Evolution have grown the regional endowment considerably and have a currently approved mine life out to 2032 with a currently approved maximum processing rate of 9.8 Mtpa. This paper examines the history, current status and future path of one part of that plan, the GRE-46 Underground Project. Topics for discussion include discovery, Mineral Resource growth under different ownership philosophies, planning, permitting and commissioning of an exploration decline and bulk sampling project, and integration with the possible future mine. Environmental sensitivities affecting regulatory approvals, timeframes, technical challenges, opportunities and solutions are discussed, along with the path required to fast-track production from the existing 14Mt, 1.4Moz Mineral Resource while complying with the requirements of modern, responsible project development stewardship.

Mar 15, 2021

By D Yates, C C(te, M Rodgerson

This paper describes how specific technical and regulatory issues related to water management have been dealt with at Anglo AmericanÆs Moranbah North mine. It compiles the collection of practices that have been implemented since 2010 in response to climatic and regulatory drivers. Operations must continually evolve as they face emerging challenges. For Moranbah North mine, one key challenge is the integration of its mine water system to that of its new neighbouring mine Grosvenor. The commitment to ongoing improvement has placed the mine in a good position to face this particular challenge.Water-related risks were identified then mitigated by technical practices, which have focused on improving underground water management, increasing storage capacity and installing a state-of-the-art control system for the management of water on-site and for releases of mine-affected water to the environment. These practices are supported by an extensive monitoring and audit system that provides confidence in the reporting of activities and outcomes. The strategy has helped the operation with its continual attempts to minimise reliance on high-quality third-party water and improving its interaction with the surrounding environment and community.CITATION:Rodgerson, M, Yates, D and C(te, C, 2013. Leading practice water management at Moranbah North Underground Mine, in Proceedings Water in Mining 2013 , pp 301-310 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 26, 2013

By P Christen

The Ernest Henry Copper gold mine situated in North West Queensland, Australia, is owned and operated by Xstrata Copper. Currently the open pit produces 11 Mtpa of ore. With open pit mining ceasing in mid 2011 development has begun on an underground sublevel cave mine to extend the life of the operation by another 12 years. When completed the open pit will be 530 m deep and 1.5 km in diameter. The orebody dips at approximately 45° and has been outlined a further 450 m below the base of the pit. This provides some challenges for the Ernest Henry underground mine which is designed to initially truck development and production ore from the end of the pit until a hoisting shaft is commissioned in 2013. Production will then increase to 5.0 Mtpa on its way to an ultimate rate of 6.0 Mtpa in 2016.This paper will focus on the capital development and infrastructure requirements for the underground mine. Areas covered include mine accesses, ore handling system, accommodations for the dip of the orebody, primary ventilation design, dewatering systems and selection of an underground workshop over surface only maintenance.Discussions include the complications arising due to the mine being located directly below a large open pit and the combination of first principle cost analysis and risk assessment which has been used to safely optimise the feasibility study designs.

Mar 21, 2011

Gravity gold recovery has been practiced for thousands of years, making it one of the oldest forms of mineral processing. Gold is 19 times heavier than water although the barren rock is generally only 2.7 times heavier. Any potential gold ore needs to be characterised to assess its amenability to a gravity recoverable gold (GRG) process based on well planned and executed test work. Scale up considerations need to be considered in designing a gravity circuit. The economic impact of a gravity circuit should be justified based on the installed cost and likely benefits. Maximising gravity gold recovery results in a faster cash flow, lower operating cost per ounce and higher overall gold recoveries compared to the several weeks required to recover gold adsorbed onto carbon. The advent of centrifugal concentrators such as the Knelson and Falcon, coupled with intensive leaching of concentrates (ILR), has revolutionised gravity gold circuit designs. Considerations associated with the sizing of the centrifugal machines and the percentage of the circulating load (bleed) that should be processed is discussed in this paper. The trends with gravity circuit layout, engineering, as well as optimum dumping cycles, are important areas which require close consideration. Key aspects of these are presented in this paper. There are a number of circuit configurations to be considered, including the integration of different gravity concentrators. Other gravity process design considerations such as fewer modules, the effect of equipment size and enhancement of process efficiency using preconcentration, together with factors that affect OPEX and CAPEX are addressed. Practical considerations of maintenance, security from theft, minimisation of risk and water balance considerations are discussed using different equipment and circuit configurations. The trend towards using gravity recovery in flotation plants is also reviewed. A number of examples are cited and good design aspects highlighted.

Aug 1, 2010

By P Gomez, R Baumgartner, G Escobar

"The Cerro Corona mine consists of a Cu-Au porphyry deposit located in the Andes of northern Peru. The deposit comprises a typical Cu-Au multiphase porphyry mineralisation that has been overprinted by an epithermal event. This has generated a complex pattern of argillic alteration facies, which was accompanied by a locally structural-controlled Au-Cu mineralisation with the presence of gold and limited Cu sulfides and sulfosalts. These features, along with the porphyry-style mineralisation, produced a multifaceted occurrence of gold.Since the beginning of operations at Cerro Corona in 2008 there has been a continuous improvement of the geological and mineralogical knowledge. All mineralogical studies have mainly focused on host rock types and, to a lesser extent, alteration minerals, but little work has been done on the mineralisation itself. As a consequence, limited mineralogical information was available for use in the process optimisation initiatives.In the last two years, a series of mineralogical characterisation studies were undertaken with two main goals. First, to gain an understanding of the mineralisation genesis and second, to obtain a detailed characterisation of copper and gold minerals to support ongoing process optimisation. The first goal was achieved by conventional optical microscopy while the second required electronic microscopy and other microanalyses due to the necessity of quantifying several minerals of interest for the processing.The results were used to refine pre-existing geometallurgical domains, explain copper and gold losses in the flotation process and to some extent, improve copper and gold recoveries. The mineralogical characterisation is an ongoing work. Mineralogy provides the basis for any optimisation exercise since it looks in detail at the material to be treated and therefore, should be part of all geometallurgical programs.CITATION:Baumgartner, R, Gomez, P and Escobar, G, 2016. Comprehensive Mineralogical Characterisation at the Cerro Corona Cu-Au Porphyry Mine – the Fundamental Key for Geometallurgical Applications, in Proceedings The Third AusIMM International Geometallurgy Conference (GeoMet) 2016, pp 221–230 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Jun 15, 2016