Search Documents

By Murphy A. S, Budod A

The Philex concentrator represents the first time Jameson Cells have been used in a cleaner scavenger application or in large scale flotation in roughing and scavenging. This necessitated a major change in Jameson cell design as well as a chan

Jan 1, 1997

By Leach B. G

A geostatistical study was made of diamond drill hole intersections within 18CC stope block at the C.S.A. Mine, Cobar, N.S.W. The stope block is located in 18CC orebody which is a massive sulphide - multiple vein, Copper-Zinc type, lacking clear definition on gangue mineralogy, base-metal assays and total sulphide considerations. Of the variograms constructed for inter- section width and copper, lead and zinc grades and accumulations, only zinc displayed behaviour amenable to model fitting and kriging procedures. Zinc grades were calcu- lated for sub-blocks comprising the total stope block and comparison with equivalent grades determined by traditional methods showed them to be generally less extreme in the highest and lowest grade sub-blocks. The total-block grades derived by the two methods were almost the same. It is suggested that the failure of copper to show variogram continuity might reflect the difficulty in defining the actual 18CC orebody, a proposition which is supported by the poor continuity in the variogram of horizontal width. In the case of lead the poor continuity may be due to the frequent manner of occurrence of galena as coarse grained patches of limited extent. The results of the study, did not provide a convincing reason to depart from the traditi- onal methods of grade estimation at the C.S.A. Mine.

Jan 1, 1979

By Rath M. C, Das R. P

Studies were carried out on dissolution and oxidation of iron powder in ammonia-ammonium carbonate solution using oxygen over pressures. Cobalt and nickel losses during iron oxidation under different conditions were investigated. Regression equations were derived for percent cobalt loss and percent iron oxidation using ammonia, ammonium carbonate and oxygen partial pressure as the variables. The equations were tested for adequacy using Fisher's test. Cobalt losses increased with the increase of initial cobalt concentration and about 400 mg/l of cobalt was lost from a solution containing 500 mg/l cobalt. A maximum of about 80 mg/l nickel was lost from 1 g/l nickel containing solution, and this loss remained the same even when the nickel concentration was increased to 7.5 g/l.

Jan 1, 1992

By Amusin BZ

The concept of rigid or yielding bolts is discussed based upon support requirements for excavations of equivalent geomechanical behaviour. The concept of equivalent geomechanical behaviour is introduced for comparison purpose where the rock mass properties are varied for a given depth (stress) so that the deformation of the roof without any support remains constant = 300mm. A simple experimental theoretical analysis for a uniform stress field acting on an axi-symmetric excavation is conducted to establish roof bolt requirements under different conditions such as width of a given excavation, time of setting of support etc. Results are presented in graphical forms.

Jan 1, 1992

Proposals for engineering works in the River Dement in recent years have been made in the context of very little geological informat- ion. Breakage of the Tasman Bridge, forced a complete re-appraisal and collection of inform- ation in order to select a new site and predict problems. Seismic, magnetic and gravity methods foll- owed by drilling have allowed an assessment of the nature, thickness and distribution of mater- ials underlying the river bed. Key discoveries included recognition of low seismic velocity silts (1100 m/s) and a separate channel for the river since the Late Tertiary.

Jan 1, 1977

By Tobin GJ

Testwork carried out in the cooling water circuit at the Yabulu treatment plant of the Greenvale Joint Venturers (Metals Exploration Queensland Pty. Ltd. and Freeport Queensland Nickel Incorporated) since 1980 has resulted in significant improvements to both fouling and corrosion control. At the same time corrosion inhibitor costs have been reduced.Acrylate-type silt dispersants were identified as the most effective means of sediment control in the circuit. An increase in the cathodic component of the corrosion inhibitor coupled with a relatively minor adjustment to water pH has yielded a two to three fold reduction in corrosion rate. It has been established that these lower corrosion rates can be sustained in the face of a 20% reduction in corrosion inhibitor addition rate. Further improvements are indicated with a change of raw water algicide.

Jan 1, 1985

Geostatistical analysis, resource estimation and three-dimensional modelling of the gold grade distribution was undertaken using exploration drillhole data taken from the Mt Leyshon gold mine. The main aims of the project were to provide an independent estimate of the primary gold resource and to improve the estimate by better understanding the statistical distribution of gold and the establishment of more robust variograms. These criteria have been achieved by the removal of low grade sub-populations, increased sample size and access to data from the most recent drilling program. The outcome of this statistical study has led to a lowering of the sill and nugget variance of the variograms used. Distinct geometric anisotropy was identified in all the resource estimation zones and was used to model gold grade distribution.Two independent resource estimates were established from the primary gold resource, one based on a geostatistical estimator (kriging) and the other on a traditional estimator (inverse distance weighting). Both methods were compared with a contemporary kriged estimate by Mt Leyshon Gold Mines Ltd.

Jan 1, 1993

By D J. D'Astoli, M D. Goodz

In 1993 a detailed review of drill sample yuuluy was rouxluard through twin and triplet drill holes using open hole, crossover suhreverse circulation (RC) and diamond drill methods. Advances in face-sampling RC methods demanded a further review of the validity and reproducibility of drill sample data. A program was undertaken to drill three RC holes using the latest technology (new face- sampling bits, dust suppressers, cyclones and compressors). Volumetric and mass studies were undertaken to review sample recoveries. Modal analyses on indicator minerals were logged to interpret the relative degree of mineralisation. Ambiguities in the results were immediately apparent and the consensus was for follow-up twin diamond holes using HQ3 coring tubes. The most mineralised RC hole was selected for the first twin diamond hole. This RC hole (MS 313) encountered one intersection of >0.47 g/t; in contrast the diamond hole (MS 342) had nine intersections at > I g/t. Results at hand show definitively that face-sampling RC drilling is not acceptable as a method of exploration for gold deposits of the Woods Point type. Furthermore it is demonstrated that RC drilling should not be used for any type of exploration of high-grade gold vein deposits related to highly fractured or porous hostrock, or areas of previous mining activity. Methods are proposed for reviewing of rates of sample recovery, distribution and cross-contamination. Comparisons also show that in limited metreage reconnaissance drill programs, diamond drilling is more similar to percussion in per metre costs, than it is credited with, and always provides more bang for the Buck.

Jan 1, 1997

The Bau Goldfield lies in the southwestern corner of Sarawak in East Malaysia. Evidence of past mining in the form of open pits and adits can be found over an area of 250 sq kin, centred on the township of Bau. Chinese were mining gold in the district as early as 1820. The Bau Goldfield so far has produced approximately two million ounces of gold, from alluvial deposits and over 50 hard rock mines. The largest single producer was the Tai Parit mine (700 000 oz) which was operated by the Borneo Company from 1898 to 1921 and by a local Malaysian family from 1991 to early-1997. Over the past ten years, gold resources totalling around one nullion ounces have been delineated through systematic exploration using modern techniques, with the bulk of the resource hosted in two deposits (Jugan and Pejiru).Triassic to Jurassic andesitic volcanics and coeval intrusives are the oldest rocks that crop out in the Bau Goldfield. These igneous basement rocks are unconformably overlain by 500 m of late Jurassic, massive, micritic limestone which in turn is overlain by a 1500 in thick flysch sequence, composed mainly of shale. Basement rocks and limestone are exposed along the hinge of a ENE-striking anticline that passes through the Bau district (Bau Anticline). A NNE-striking belt of Miocene granodiorite porphyry stocks and dykes also passes through the Bau Goldfield. All of the known gold deposits lie within 5 km of this zone of intnisives, with a concentration of deposits at the intersection of the intrusive hell with the Rau Anticline.

Jan 1, 1997

The Iron Prince orebody occurs within the Lower Middleback Jaspilite Horizon of the Middleback Group and consists of hematite within host rocks of jaspilites and schists. The ore was probably the product of leaching of silica from jaspilites and replacement by iron, concentrations occurring in suitable structural traps. The narrowness and the presence of extensive dolerite amphibolite dykes within the orebody make it essential to operate a grade control programme in advance of the faces. Information from drilling is drawn up on bench plans, step plans and impurity overlays, and these serve both in day to day production planning and in long term planning. Mining is done selectively by open-pit methods and blending conducted by keeping at least three faces of different grades of ore open at any one time. No stock piles of ore are kept for blending, but contact ore, contaminated ore and enriched material are dumped for later beneficiation.

Jan 1, 1971

When lying over 200-250m depth, many seams and surrounding strata are gassy enough to create mining difficulties , particularly in highly productive longwalls as well as in their development headings. In addition to the gassiness of seams or stra- ta in the outgassing volume around working, the shape expansion and limits of this one influences much the intensity of gas emission. These charac- teristics of outgassing volume differ very much ac- cording to the permeabilities of the seams and strata encountered by their fracturation due to mi- ning. Moreover, the shape of the outgassing volume is very much modified by the rate of advance of the face. In nearly impermeable deposits, gas flows from a limited outgassing volume. When the rates of advance of a face are medium or low, the shape and dimensions of this volume do not change very much and outgassing volume is translated progressi- vely with the face advance. This explains why, in the past, it was observed that there was for each seam an average steady specific emission of gas, round which the volume of gas evolved per mined ton or per mined unit area, calculated over a cer- tain time, was oscillating. Combined with a statisti- cal irregularity coefficient, this allowed prediction gas of emission and thus to take decisions for air ventilation, drainage, and eventually production.

Jan 1, 1988

This paper describes several sources of external dilution affecting the stope walls during underground sub-level and bench stoping. Factors which control ground behaviour such as the geometry of the openings, the influence of geological discontinuities, stress re-distribution and blasting practices are discussed. Crown stope instability due to stress concentrations induced by changes in the excavation geometry, is discussed and the most efficient ways to sequence blasting within a stope are analysed. Effects of undercutting by blasting, blast damage in the near field and cut-off slot blast designs are analysed. The influence of dynamic loading on the exposed walls as well as the practice of blasting fill passes within stope crowns are discussed.

Jan 1, 1995

By Quinlan M. J, Ratcliffe J. S

Chemical kinetics is a dependent process which usually correlates the rate at which a reaction proceeds with the mechanism descriptive of the manner by which reactive particles interact. Given the latter, the object gen- erally is to find the reaction rate dependency in terms of an intensive property of the system - number of reactive particles present, and of the energetics of the system - usually temperature. Chemical kinetics depend on a dem- onstration that reaction considerations alone control the phenomenological process under study. For these rea- sons, chemical kinetics are usually involved in homogeneous gaseous systems. Even in liquid homogeneous sys- tems earliness or lateness of reactant mixing rather than chemical kinetics may be controlling. Considerations of transport phenomena are involved in heterogeneous systems and often control the observable rate:an additional problem in such systems is to apportion the rate due to mass transfer - usually a linear process - and that due to reaction which may be linear or non-linear. Experimentally, conditions are often chosen so that only one consideration controls but this becomes more difficult where solid phases are involved. Kinetic modelling involves considerations of chemical kinetics, transport phenomena, and factors attributable to the physical environment in which the process takes place. The latter two considerations may be quite different as between experiment and plant. The kinetic model may be a mathematical representation of a conceptual mech- anistic model of the reaction. Alternatively, it may be an empirical relationship resulting from, for example, some curve fitting procedure applied to experimental data. The latter approach may be necessary where the system is particularly complicated.

Jan 1, 1975

By Pratt V, Davis K

Challenges facing middle management in the 1980's and beyond are not confined to business matters such as industrial relations, government and legal constraints, corporate takeovers, and commodity marketing. More particularly they deal with people issues and the interrelationship of corporate/ family relationships. There is a need for corporations to acknowledge the growing conflict between corporate/family roles being brought about by such matters as equal opportunity, double professional marriage partnerships, personal mobility and the increasing stress faced by managers as a result of current demands and expectations being placed on them. While the main responsibility for managing professional life as well as the relationship between professional and private life rests with the individual executive, corporations nevertheless have a major responsibility to assist these executives in this management process. Corporations in Australia are taking steps to address this situation but much more needs to be done. This was highlighted in the March 1985 "Middle Management" course with its associated Spouses Programme presented jointly by Australian Mineral Foundation and The Australian Administrative Staff College. Effective communication is at the heart of the matter but no amount of training on this subject will bear fruit unless there is an associated commitment by executives to improve the effectiveness of their communi- cation process both in their corporate and family roles.

Jan 1, 1986

By D Obeng, D Alexander

Over the past five years, commodity prices have been high and the focus of many plants has been æthe more metal the better, at whatever costÆ. In the recent economic crisis, the focus has shifted more to reducing the cost of production and operating at higher efficiency. Since 2002, JKTech has partnered with the Century mine in north-west Queensland to transfer technology and understanding through the good, bad and ugly economic environments, using methodology and techniques arising from research at the Julius Kruttschnitt Mineral Research Centre (JKMRC) and other research institutions around the world as part of the AMIRA International P9 Project. The JKTech studies were concentrated around the primary zinc circuit. During this period, Century expanded the primary zinc regrind capacity, installed additional scavenging capacity, installed and commissioned a Jameson cell for concentrate cleaning in the carbon preflotation circuit, and installed additional primary grinding capacity. Flotation circuit models were developed for each of the survey campaigns and enabled opportunities for further improvement to be identified, implemented and tested in the subsequent campaign.

Jan 1, 2009

By D Feng, G C. Lukey, J S. J, R R. Dagastine

An ongoing challenge in the coal industry is pyrite removal using the flotation method for fine particles. The use of a æseparation in frothÆ (SIF) technique to recover coarse particles of up to a few millimetres in size has presented a potential solution. However the commercial success of SIF is still limited due to the poor understanding of the separation mechanism. The particle floatability in SIF is determined by the constructive or destructive stresses resulting from the forces exerted by the particle on the bubble films. Hence, the surfactant properties and the mineral characteristics (eg hydrophobicity, shape, etc) are the key factors that control the interaction between the particle and froth. In the present work, the interaction forces between different particles (ie crushed glass, pyrite and coal) and a single air bubble are measured in a non-ionic surfactant solution (pentaethylene glycol mono n-dodecyl ether, C12E5) using an atomic force microscope (AFM). Experimental results show that the interaction is primarily dependent on the contact angle (ie the degree of hydrophobicity of the minerals). For crushed glass, the transition from repulsion to attraction was observed as the contact angle increased. As the concentration of C12E5 increased, the adhesion force was suppressed due to wrapping effect. For coal and pyrite with much higher hydrophobicity, long-range attraction was observed. The effect of shape factor was only visible at high surfactant coverage where sign of destabilisation became noticeable on the retracting force curve. These results provide a fundamental understanding of the direct interaction forces of a complex real system between an irregular particle of either crushed glass, pyrite or coal and a single air bubble. Theories developed for interpretation and modelling are thus far based upon the study of ideal systems of glass or polystyrene spheres and an air bubble and were incapable of explaining the interactions in complex real systems. The presented measurements were a first approach to the problem of real mineral-bubble interaction in flotation systems. Thus, the results can only best be interpreted semi-quantitatively.

Jan 1, 2005

By Greenhalgh L. P H

The opportunities offered by an increasingly volatile world invite the international consultant or engineering services contractor to broaden attitudes, diversify interests, expand capabilities, retain and develop specialist skills and base judgements upon sound principles and solid experience. The wide-ranging scope of this review reflects such a change but the topics of discussion are not intended to be exhaustive or to detract from many other current developments.The subject of environmental protection, effluent control and pollution prevention is a primary consideration in the application of many mineral processing technologies but is not covered here. There is an array of developments relating to noxious gas emissions and toxic wastes and the paramount importance of this matter justifies comprehensive conferences dedicated solely to the application of suitable measures. This review concentrates therefore on the main stream processing techniques for the primary recovery of values.

Jan 1, 1993

By Roddick F

From its mining lease at the northern end of Cohens Reef at Walhalla in the North Gipps- land mountains, the Long Tunnel Extended Gold Mining Company produced 13,695kg of gold, which at 1982 prices represents a value of about $140 million. In the period 1885 to 1908 the mine was one of Australia's principal reef gold producers, being top Victorian producer in six of these twenty-four years. Prior and subse- quent occupants of the lease produced an addit- ional 160kg of gold. The Extended and the other mines on Cohens Reef whilst contributing importantly to the financial resource of Victoria, were the sole important support for the substantial town of Walhalla that had grown up around them. When the mines closed, Walhalla gradually reduced from a bustling developed town to the present attractive mountain village so favoured by tourists.

Jan 1, 1982

By Floyd JM, Bultitude-Paul J

The development of a process for the extraction of antimony from materials produced by Greenbushes Tin Limited has been carried out based on theoretical and laboratory studies. The materials treated have included concentrates of tantalite and cassiterite containing antimony at levels ranging from 0.3% to 2%. Roasting under controlled atmospheres is required to stabilise Sb203 rather than the low vapour pressure metal or higher oxide. Sulphidising additives such as pyrite, pyrrhotite or sulphur give enhanced antimony removal from tantalite and cassiterite at roasting temperatures of 900¦ to 1100¦C. Substantial elimination of antimony to levels of 0.1% or less was Achieved.

Jan 1, 1986

By Gonzalez-Dominguez J. A, Dreisinger D. B

At Cominco's Zinc Refinery at Trail, British Columbia impurities are removed from zinc sulphate electrolyte by a two-stage purification process using zinc dust. Copper, cadmium and thallium are removed in the first stage whereas cobalt is removed in the second stage. Cobalt removal kinetics are affected by soluble antimony and copper additions to the electrolyte. This study was focused on the kinetics of cobalt removal by zinc powder cementation. Experimental variables included copper and antimony concentrations, pH and temperature. Common organic additives employed in zinc plants were studied to determine potential interactions with the cobalt removal process. Cementation products obtained from laboratory experiments and plant practice were studied using SEM. A number of significant results were obtained: 1. Copper and antimony ions were sustantially removed from solution during the early stages of the cementation reaction (within the first 15 minutes). Cobalt cementation kinetics are slow and follow a first order kinetic regime. 2. A drop in the cobalt removal rates can be correlated with a rise in the Eh of the slurry. 3. Ligninsulphonate, Percol 351 and animal glue at levels of 2 mg/L significantly impede cobalt cementation.

Jan 1, 1993