Search Documents

By Pilkington T, Noy A

The Yallourn North Extension (YNX) open cut mine ceased mining operations in early 1989. YNX may be used again for coal supply at the discretion of the Coal Corporation Of Victoria (CCV); this has resulted in the need for interim rehabilitation of the site which may last many years, or indeed, permanently.The site has suffered substantial surface erosion over the years with large areas of bare clay and coal batters remaining exposed. The first priority is to reduce the quantity and improve the quality of stormwater runoff from the site. This is best achieved by appropriate revegetation and the use of existing landform depressions as silt trap/wetland areas. Proposed rehabilitation needed to take into account the sensitive fire safety of the open cut and the option to re-open the mine if CCV deems appropriate.The authors detail the factors involved in the rehabilitation proposal and the multi-disciplinary approach to planning including engineers, scientists, a forester, landscape architects and community input. The rehabilitation design included early consideration of land use and ongoing maintenance issues linked to water quality improvement factors including vegetation. Engineering input was required for reshaping and clay covering exposed coal batters and the design of silt traps which will revert to wetlands in future. The integration of each discipline has produced a rehabilitation design pleasing to both the SECV and community alike.

Jan 1, 1992

In Mount Isa voltage and frequency fluctuations caused. by haulage shaft operation gave considerable difficulties with the initial application of Atomic Absorption Spectro-photometry.The methods used to stabilise the various units ' have been described.- Some other difficulties and the means used to eliminate or reduce them together with a-modified burner design are also discussed.

Jan 1, 1963

By J Coveney, A Rich, D Grimsey, J Wood, S Creedy

In 2021, BHP and Metso examined processing of high-MgO nickel sulfide concentrates using Metso’s Ausmelt Top-Submerged-Lance (TSL) technology. Test work was conducted in Metso’s pilot test work facility in Dandenong, Australia to explore operability of the SiO2-FeO-MgO-CaO-NiO slag system across a wide range of compositions, temperatures and bath oxygen potentials. Pilot-scale testing aimed to define slag ‘operability limits’, representing the lowest bath temperature at which stable process and equipment operation could be maintained. This work was supported by FactSage™, version 8.2 (by Thermfact/CRCT and GTT-Technologies) thermodynamic modelling, slag viscosity measurements, physical characterisation of quenched slag samples performed by the University of Queensland and benchmarking of commercial-scale TSL nickel smelting operations. A wide range of slag compositions were examined, with Fe/SiO2 ratios varying from 0.4–1.1, CaO content from 0.8–7.0 wt per cent and MgO content from 6–19 wt per cent. Slag SiO2/MgO ratio, wt per cent CaO and matte grade were found to have the greatest impacts on identified operability limits. Operability limits were found to be influenced by both the solids content in slag and viscosity of the remaining liquid slag phase, with the relative contribution of these parameters heavily influenced by the slag composition. In the majority of trials, limits were defined by a theoretical solids content of 40–50 per cent, however in trials with a low Fe/SiO2 ratio and/or low wt per cent CaO, limits were characterised by a much lower solids content due to the increased effect of the liquid slag viscosity in determining the behaviour of these slags. The test work highlighted inherent flexibility of the Ausmelt TSL process to operate across a wide slag range of slag compositions and recover from process disturbances without an interruption to feeding. The trials also demonstrated the possibility for Ausmelt TSL technology to process concentrates with an Fe/MgO ratio as low as 1.4, which has important implications to the commercial-scale processing of high MgO feeds. Arsenic rejection across the trials was very good, with only 30 per cent of arsenic in the feed inputs reporting to the matte phase. Such high levels of arsenic removal provide the Ausmelt TSL process with a notable advantage over alternative smelting technologies.

Aug 21, 2024

This is the time of year tor the presidential address, and with the present incumbent engaged in the coal mining industry, it will therefore come as no surprise to you that the theme of my address this evening is concerned with coal.There are other reasons for this apart from my contact with the coal industry. At present, coal is supplying considerable overseas revenue at a time when the remainder of the mining market is in a somewhat depressed state. That times will change goes without saying, if history is to be believed.However, so far so good for coal. My first reaction when The Institute indicated its wish that I be president for 1976 was to become deeply conscious of the honour bestowed on me.On consideration, I realized that very few past presidents have been intimately connected with the coal mining industry to the extent of indulging in it for lengthy periods as a full time occupation or, conversely, a part time interest for a long time. It also appears that not one had started their career in the industry. In my case, 'also, there were 8 very interesting years ,as a gold miner and metallurgist before commencing in coal.It therefore seemed appropriate to endeavour to discover ,why this should be so, as coal mining is now a very important part of a very important industry. What were the reasons why the industry took so long to emerge when there were ample reserves of easily accessible coal?Frankie and Johnnie in their bar room epic of the depression years concluded, and I paraphrase, that "their story held no moral, their story told no tale". If my story has such a message, it could perhapsbe construed as reinforcing the oft-repeated dictums, true or false, that "history repeats itself" or "man never learns".Coal mining is by far our oldest major Australian industry except for agriculture. Its history is almost as old as that of settlement:For various reasons, there has been a glamour associated with metal mining ventures which prob...

Jan 1, 1976

By Z-Y Pi, B Zhang, S Wen

"The paper introduces the structure and work processes of outside auger hollow claw tipped mechanical sampler for coal. Twenty sets of claw tipped sampler performance tests show that: The design of inner hollow cylinder-type (?180 mm) can ensure to take a coal sample with nominal top size of 60 mm. Built-in self-cleaning piston pusher ensures no adherence and blocking of the sample. The operation practices show that the mechanical sampler can operate in order for taking coal sample with up to 16 per cent of total moisture. Claw closing design can avoid sample leaking or spilling during the claw lifting and ensure the integrity of primary increment. Ultrasonic positioning device makes the sampler capture the materials no less than 10 cm from the bottom of the wagons, basically meeting the requirement taking full depth of the sample. The precision and bias test indicates that the moisture and ash have no relative bias under the sampling process; the sampling precision is in accordance with the requirement in IS013909.At present, the spiral mechanical sampler is widely used for coal sampling but there are many limitations during application, for example: It is difficult to capture a large size sample, so the size range of a coal sample taken is limited. There is easy adhering or blocking for high moisture coal, which will result in the mixture of different increments, wear of sampler and the difficulties for cleaning and maintenance of sampler. It is difficult to capture the coal sample at lower than 30 cm from the bottom of the wagons, in order to avoid damage of the vehicle. It is possible for coal sample loss and spilling during the sampler lifting, due to the unsealed sampler.For the outside auger hollow claw tipped mechanical sampler designed for solving the above problems, the opening distance of the claw is the opening size of the sampler and makes the size range of the coal sample to be taken wide. During sampling, the two pieces of claws open and the sampler rotates vertically downward to capture an adequate coal sample after reaching the specific point. Then the two pieces of claws close tight automatically to ensure there is no coal leaking or spilling. The inner pusher of the sampler will prevent from the adherence and blocking of the coal sample effectively.CITATION:Zhang, B, Pi, Z-Y and Wen, S, 2012. Outside auger hollow claw tipped mechanical sampler for coal, in Proceedings Sampling 2012, pp 41-44 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Aug 21, 2012

By A Hosseinzadeh Barforoosh, A Abedi, M Taji

The effect of blast loads on beams is one of the main issues in the analysis of steel structure. In this study, experimental tests on steel beam under blast loading, and also numerical simulation by the Autodyn software to analyse these structures, is discussed. Experiments on steel beam size of 12 by Emulite4 explosive with 30 mm diameter and cortex is done. The patterns of cutting and bending generated in the two tests (empirical and simulation) show a good match.CITATION:Taji, M, Hosseinzadeh Barforoosh, A and Abedi, A, 2015. Comparison of experiment and simulation of blast loading on the steel beam, in Proceedings 11th International Symposium on Rock Fragmentation by Blasting, pp 161–168 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 24, 2015

Here, in what is partly a review and partly a personal viewpoint, I take stock of changes in emphasis and comprehension on the subject of basaltic volcanism in the decade that has passed since the completion of the landmark Basaltic Volcanism Study Project (1981). I concentrate attention on the relatively neglected physical-volcanology aspects (in 1988 it was still possible to publish a 340-page book on flood basalts with barely any mention of physical mechanisms).I adopt the useful unifying concept of "volcanic system" to embrace the invariably-present intrusions as well as the volcano; I consider controls exercised by magma-supply rate and modulator-mechanisms on the nature of the system;I emphasize that sheeted-intrusion complexes, consisting either of dikes or inclined sheets (depending on the ability of the system to expand laterally) occur in all eroded major systems and fuel geothermal systems; I show how constraints set by cooling of narrow intrusions cause such complexes to be wedge-like and produce considerable rotations; I consider the role of the level of neutral buoyancy in making magma chambers possible, causing lateral subsurface magma flow and localizing intrusions, while the LNB itself can be accentuated by intrusions; and I examine the possibility that underwater systems could have very different internal structures from systems on land.

Jan 1, 1990

By A Hacket, M Haest, I Vitins

Infrared spectroscopy has the ability to accurately measure mineralogy of drill cores, allowing for better spatial characterisation of iron ore deposits and potentially improving the prediction of key mining and processing parameters at the deposit scale. BHP Billiton Iron Ore is using infrared spectroscopic drill core logging to provide fast and accurate mineralogy for diamond cores and reverse circulation (RC) samples.Mineralogy can be predicted from infrared spectroscopic drill core data with errors on estimates ranging from six to 12 weight per cent. The error on the clay estimates is significantly lower than for hematite and goethite content estimates. This manuscript presents the results from a study on a bedded iron ore deposit, hosted in the Brockman iron formation, for which infrared spectroscopic data were collected on all of the diamond and RC drilling. Results show that these mineralogy estimates improve drill core logs, the geology model and the metallurgical block model.CITATION:Haest, M, Vitins, I and Hacket, A, 2013. Infrared spectroscopic drill core logging - making inroads to deposit scale 3D mineralogy, in Proceedings Iron Ore 2013 , pp 251-258 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 12, 2013

By A E. C Peres, P R. M Viana

The role of flotation columns in comparison with conventional mechanical flotation cells is discussed under the scenario of Brazilian flotation technology. All iron ore concentrator circuits commissioned since 1990 incorporated column only flotation technology in rougher, cleaner, scavenger configuration. Columns were also added to existing circuits, especially at the cleaner stage. Columns were also incorporated to phosphate ore flotation circuits operating mechanical cells. In two phosphate concentrators, columns substituted for all mechanical cells. Columns perform the cleaning stage in a large sulfide copper concentrator, following rougher flotation in tank cells. Scavenger of the cleaner tailings is performed in tank cells at this plant. Other ores that are concentrated in flotation columns include graphite, talc, lead-zinc sulfide, and a zinc hydrometallurgical residue for silver recovery.

Jan 1, 2005

The light microscopic study of the physical structures of coal and associated mineral matter is an important technique in providing information on the characterisitics and possible behaviour of coals in industrial processes. However the ultrafine nature of coal and mineral particles together with the limits of resolution of the light microscope restrict such studies. Scanning electron microscopy (SEM)with its better resolution and higher magnifications is the means by which further information on coal properties can be obtained. An associated energy dispersive X-ray specrometry (EDS) method allows non-destructive in-situ chemical analyses to be carried out at the same time.

Jan 1, 1989

By Brien RT, O&apos

The work reported in this paper extends,-bhsb on the "Heat Hardening of Artificial Magnetite ;Pellets"., which was described at the- International Symposium on Agglomeration ;-sponsored by the American Institute. of Mining, Metallurgical and Petroleum Engineers at Philadelphia; U.S.A. in April, 1961. Whereas- that work was of a.,more basic nature, -serving to illustrate the suitability of artificialòmagnetites with various.admixtures, to the application of heat hardened pellets, on: this occasion the aim-is to illustrate the procedures-which were used-to- establish the dimensions of commercialòrecuperativ strands for Australian raw materials,The nature of the pellet feed, i.e. relatively uniform :spheres of4 3/8 in. - 7/16. in. diameter, makes it possible to use small scale static pots for test work. By the use of a closed system and the measurement of suctions, gas f lows, and temperatures through beds, the speed and heat requirements of the various stages of heat hardening can be measured, so: that for a specified quality of product estimates can be made of the broad design characteristics of a moving grate system. In practice of course it is .usual to correlate the data from this type-of :experimental 'apparatus with . existing production units upon which good operating data, in the statistical sense, are available.

Jan 1, 1963

By A Specht, A Müller, V Montenegro, S Winkler, E Klaffenbach, A Schmidt

In the process of primary copper smelting in flash smelting furnace (FSF), the ratio of iron to silica (Fe/SiO2 mass ratio) primarily determines the slag viscosity and magnetite formation. Viscous slag does not only cause difficulties in daily operation, such as in tapping, it also increases the copper losses to slag. Thus, keeping the Fe/SiO2 mass ratio at the desired level is an important aspect of FSF and slag cleaning furnace (SCF) operation. In this study, the improvement of the Fe/SiO2 mass ratio was conducted in two steps: First, the optimal Fe/SiO2 mass ratio was derived based on thermodynamic data. Based on this analysis, appropriate control limits were determined. Second, this range of favourable Fe/SiO2 mass ratios was implemented into operation by an advice-based control system, which suggests the addition of silica based on the analysis of SCF slag. As this approach was successful, the same advice-based control system principle was adapted for the coke addition to the SCF. After testing the new advice-based control for several months, the production data confirm the predictions by thermodynamics: since the prediction was implemented as an advisor, the copper and magnetite content in SCF slag is significantly reduced and viscous slag is reported less often by operations.

Aug 21, 2024

By M Field

Kimberlite pipes, as opposed to dykes, sill and secondary deposits, are the primary target for diamond exploration companies because they have simple geometries and can contain large volumes of potentially diamond-bearing ore. Once discovered, important decisions have to be made regarding the sampling of these geological entities to establish the total volume of ore present, and to define the internal geology, which can be complex in nature and controls the distribution of diamond grade. It is essential that as part of this process the uncertainty in constructed geological models are assessed. In this paper the Orapa AK1 kimberlite pipe in Botswana is used as a case study to explore a potential methodology for defining this uncertainty. The uncertainty of the rock volumes of different types can be characterised by a geostatistical approach. Geostatistical simulations, based upon a plausible representation of the geological bodies, provide different possible images of the orebody that can be considered as different realities. By testing different borehole layouts and drilling the orebody virtually on the computer, many different, but equi-probable realisations of the pipes can be produced. It is then possible to estimate the rocksÆ volumes and compare them with the actual ones. A statistical analysis of the relationship between estimation error and the number of boreholes can then be used to optimise the next sampling campaign. The rock volumes are obtained from a two-step simulation process. Firstly, the pipe geometry is simulated by means of introducing variations around the geological block model, by an original method called centre point simulation (CPS), which has been developed for this purpose. Secondly, the internal geology is then simulated within the pipe. The methodology for simulating the internal geological zones has to be adapted to the level of information and to the geological structure itself. The upper portion at Orapa AK1 is filled with sedimentary crater facies. Here plurigaussian simulation techniques can be applied that are adapted to the simulation of sedimentary facies. The central zones of the pipe are typically subvertically-oriented massive volcaniclastic deposits and breccias and the lower regions comprise a complex root zone. CPS is appropriate for these zones.

Jan 1, 2006

By L Cain, C Every, S Mirlatifi, J Ashley

This paper presents a geographic information system (GIS) based method for the prediction of ground movement and the associated impact on existing buildings and structures due to tunnelling in the North West Rail Link (NWRL) project. The NWRL is a priority rail infrastructure project for the New South Wales (NSW) Government and includes 15 km of twin tunnels between Bella Vista and Epping, which will be Australia’s longest rail tunnels. The NWRL tunnels will be constructed in an urban environment where the prediction of ground movements induced by tunnelling and the associated impacts to existing structures must be assessed in the early design stages of the project. An assessment process was developed using GIS able to respond to design changes.An iterative GIS analysis methodology was developed to generate ground settlement contours and identify impacted buildings and structures in response to multiple changes in tunnel alignment during design development stages. The GIS analysis undertook to rapidly provide detailed and accurate parameter information including tunnel depth from surface, tunnel separation, diameter and sample point proximity to the tunnel and assess ground movement contours along the project alignment. Determination of the ground surface settlements were based on empirical methods proposed by Peck (1969) and Mair (1993). The control parameters and the relationship between damage categories and risk classifications for impact assessment were based on Burland, Broms and de Mello (1977), Rankin (1988) and Boscardin and Cording (1989) methods.The GIS-based ground movement impact assessment approach adopted for the NWRL project demonstrates an efficient, iterative and robust approach and could provide an initial framework for other similar tunnelling projects where rapid design changes and early understanding of tunnelling impacts are required to bring greatest benefit to all stakeholders.CITATION:Mirlatifi, S, Cain, L, Ashley, J and Every, C, 2014. An iterative geographic information system based approach for the assessment of tunnelling impact to existing buildings and structures, in Proceedings 15th Australasian Tunnelling Conference 2014 , pp 647–652 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 17, 2014

By Membrey W. B, Partridge A. C

Lower transportation costs, improved handling and better utilization efficiency are some of the reasons that make low moisture coal product desirable. There has been considerable interest in the development of effective coal dewatering techniques to achieve this result. One avenue of considerable merit for enhancing dewatering processes is by modification of the surface chemistry of the coalwater slurry system by chemical means, resulting in better performance of existing equipment. This paper reports the results of an investigation of the utility of surface active agents in the enhancement of fine coal dewatering. A large variety of proprietary dewatering agents have been studied in relation to their efficiency in enhancing the dewatering of a number of Australian coals. Properties of particular coals that make them amenable to improved dewatering by particular chemical agents have been identified. Surface studies, including surface tension and zeta potential measurements as a function of surfactant concentration, as well as dewatering assessments, were used. Particular attention was paid to filtration, but the results could be applied to other dewatering systems.

Jan 1, 1989

By R Zhang, J Xu, X Lv, C Bai, S Zhang

This paper studies the grinding behaviour of vanadium-titanium magnetite concentrate in a ball mill. The grinding kinetics, surface morphology, lattice distortion, wettability and moisture capacity were analysed. Grinding kinetics equation was established based on population balances model with the size distribution data from a laser diffraction technique. The SEM photos of the ground concentrate showed that the surface gets rough with increasing grind time. Agglomeration of fine particles was enhanced when the grinding time reached 30 minutes. X-ray diffraction results showed that a loss in crystalline occurred with increasing the grinding time. The peaks of the X-ray diffraction patterns are significantly broadened with increasing grinding time. Wettability, characterised by contact angle between the material and water, improved due to the fact that the surface roughness increased with increasing grinding time. Moisture capacity of concentrate ascends abruptly in the first three minutes and then changed slowly with increasing grinding time. The water transfer coefficient in the particles increased rapidly in the first six minutes and then decreased quickly until grinding time reached 12 minutes.CITATION:Zhang, R, Lv, X, Bai, C, Xu, J and Zhang, S, 2013. Wet grinding of ?vanadium-titanium magnetite concentrate in a ball mill, in Proceedings Iron Ore 2013 , pp 511-518 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 12, 2013

By K Vallo, T Haimi, J Pihlasalo, J Hamuyuni, M Lindgren, F Tesfaye

Decarbonisation of the steel industry has recently attracted a lot of research and technological development. Most of the technological developments are centred around the replacement of blast furnace (BF), which has been the main primary smelting furnace in the ironmaking step of steel production. Replacement of the BF is not an easy task because of BF’s many established capabilities over the years, especially its ability to use low-grade iron feed. In this regard, Metso has developed its own technology, Metso’s Outotec direct reduced iron (DRI) smelting furnace, to tackle this problem. The recently developed six-in line electric furnace for DRI smelting can be used for primary smelting of DRI from blast furnace grade iron ore. Unlike the electric arc furnace (EAF), the DRI smelting furnace can handle larger slag volumes that emanate from the high gangue in BF grade DRI. Therefore, fluxing plays an important role in operating the DRI smelting furnace. This paper presents fluxing options and proposes slag quality and operating windows for the DRI smelting furnace. Also, the effect of slag on refractory durability will be discussed.

Jun 19, 2024

YOUR Excellency, Fellow Members of the Australasian Institute Of Mining Engineers and Gentlemen:- Nearly a decade has passed, since our Institute first met in New Zealand. May I, at the very outset of this second gathering, congratulate the Institute on the great progress that has been made in the interval. At the first meeting in New Zealand in the year 1903, I understand that less than 20 persons were present, and now in the large concourse before me I believe there are not fewer than 140 persons, while if every member of the Institute to-day where here there would be over 500 which is a great change from a membership of only 250 in 1903. I feel deeply appreciative of the honour you have conferred upon me by electing me your President for the year 1911. In return for the compliment, may I ask you to believe that I shall do everything in my power to further the interests of the Institute throughout the coming year.It is a great regret to me to realise that soon my work in New Zealand will be over. However, I trust that the new...

Jan 1, 1911

By Moore A. J, Evans R

Blast vibration control and assessment techniques have been developed which supplement traditional charge mass scaling methods. The improved techniques, which can be used to predict air and ground vibration levels at the planning stage, and to assist in the control of blasting operations, have reduced the level of operating risk concerning blast vibration. In addition to such factors as charge mass, distance and blast vibration levels, these additional techniques take account of orientation of the blasting face, topographic shielding, wavefront reinforcement, and meteorological conditions. They have assisted in compliance with specified blast vibration levels for environmental licence and mining lease conditions, the reduction of blast vibration nuisance to residents in the area surrounding a mine, and control of building and rock structure response in adjacent areas on the mine lease area.

Jan 1, 1994

The equipment and general smelter layout for the Mount Isa Copper Smelter were designed by engineers associated with the American Smelting and Refining Company and by Mount Isa staff engineers. The final notice of site was dictated by the need for 'building the smelter near the existing Mount Isa power house to enable full use to be made of the steam from the waste heat boilers. Although much excavation work was necessary before concrete foundations could be poured, the location lends itself to further expansion should it become necessary. The plant is designed and constructed to involve straight line smelting operations which include the following major steps in the overall scheme.1. Charge make-up.2. Roasthig.3. Reverberatory smelting.4. Converting.5. Refining.6. Casting.CHARGE MAKE-UPA system of proportioning bins is provided for preparing the feed mixture for the roasters, Sulphide concentrate containing 24% copper wiil be delivered by belt conveyor from the filter plant to the smelter storage patio. This is a large roofed concrete floor that provides a maximum storage capacity of 8,000 tons of concentrate. Eight proportioning bins located below but adjacent to the south end of the patio will be used for actual charge make-up from which concentrate, ore and flux will be proportioned to the feed belt and conveyed to the roaster feed hoppers. Four of the proportioning bins, 80 tons capacity each, will receive...

Jan 1, 1953