Search Documents

By Young D. R, Webb I. D

The hydro-chlorination of Fe2O3 and Fe304 has been investigated in the range 850-950¦C in order to elucidate the role of iron in the segregation process for nickeliferous laterites. The kinetics of Fe203 chlorination using 20% HC1 - 80% N2 gas mixtures is consistent with a single-stage structure control model, whereas Fe3O 4 exhibits a two-stage reaction mechanism. Oxygen potential measurements using a CSZ probe located above the bed and X-ray powder diffraction results confirm the proposed reaction scheme. When a serpentine nickeliferous laterite (1.03% Ni - 11.7% Fe) was chlorinated at 900¦C with a 20% HCl - 80% N2 gas mixture it was found that the iron oxide in the ore was extracted in a similar manner to the synthetic iron oxides. Also, it was found that the nickel extraction from the ore paralleled that of the iron and the tests indicated that for the major part of the extraction, the solid nickel species were in equilibrium with the gas phase. The recovery of nickel from laterite ores by the segregation process has been investigated by a number of workers and several extensive reviews of the literature associated with this field have been published (Iwasaki, 1972; Canterford, 1975; Wright, 1973).

Jan 1, 1987

By E Villaescusa, C Drover, I Onederra

Development face destress blasting is a construction technique in deep mining, which aims to prevent, reduce the frequency, or manipulate the timing of violent, stress-driven rock mass instability at the face. This paper presents a destress blasting design concept that was optimised for the specific rock mass conditions of a deep mine using the Hybrid Stress Blasting Model (HSBM) software. The design was then implemented in an area of the mine where stress-driven instability of the face regularly occurred during development. An adjacent tunnel was constructed in parallel without destressing, within the same rock mass conditions, as a control. The rock mass response to each excavation was quantitatively compared using high-resolution local seismic monitoring. Visual observations of the fractures created by destress blasting were also made. The analysis indicated that destressing reduced both seismicity and the rock mass stiffness ahead of the face. This was inferred from the spatial broadening of the development seismogenic zone and the typically significant reduction in the spatial density of seismic events. Seismic source mechanism analysis also indicated that destress blasting generated a much wider variety of failure modes than conventional blasting. Most seismic source mechanisms following destressing were associated with natural joint structures. A relatively small portion were consistent with newly created blast-induced fractures. The greater diversity of rock mass failure modes associated with destressing implied a lower potential for stain-energy accumulation within the rock mass at the face, and thus a lower risk of hazardous instability. Observations of visible rock fracturing indicated that the major principal stress influenced the damage intensity on natural geological structures within the destressed zone, and that numerical predictions of radial fracturing limits made by HSBM analysis were realistic representations of the real blasting performance.

Nov 29, 2022

By Teniswood CF, Sheppard I, Mason LG

An industry initiated project, sponsored by the National Energy Research Development and Demonstration Council, has worked for two years in developing design guidelines for underground coal mining machinery.Continuous miners and shuttle cars were selected for the initial development of design guidelines as these machines were linked with 7500 lost workdays and 490 reported injuries during the preceding two years.

Jan 1, 1991

By Mackinnon I. D R, Glikson M

Samples from the Callide Coal Measures, Queensland, Australia, containing the minor maceral, micrinite, have been studied using optical and electron-optical techniques to determine the precise compositional and structural nature of micrinite when in association with vitrinite macerals. Emphasis has been placed on direct spatial correlation of optical and electron-optical data due to the fine grain size (90 per cent of the component) and, as such, should not be considered a maceral.

Jan 1, 1991

By Clark I, Stockton N, Warren L

Nickel flotation circuits currently experience difficulties in recovering fine particles of pentlandite less than ten microns. By agglomerating these particles using shear-flocculation it is hoped to improve the recovery of these fine particles. A sample of massive sulphide ore from the Kambalda region was separated using magnetic separation to obtain a high grade pentlandite concentrate (> 90 per cent). This was finely ground to produce a sample with particles of 50 per cent minus 10 um in size. This sample was then shear-flocculated using a variety of reagents, including xanthates, dithiophosphate and mercaptobenzothiazole (MBT). The effects of reagent type and concentration, conditioning time, impeller speed and type, and pulp density were studied. Froth flotation tests were also conducted on the shear flocculated pulps to compare the effects of xanthate and MBT on the recovery of pentlandite.

Jan 1, 1992

By Zamel G. I, Zenari L. P

Technological developments in modem Tunnel Boring Machines (TBMs) and associated back-up equipment are offering significant alternatives for mining operators to consider, in the selection of equipment for coal mine development drifts, roadways, longwall gate roads as well as metalliferous mining declines and development drives.Greater flexibility in handling variable ground conditions, muck disposal and radius of turn as well as advance rates, are just some of the areas where modem TBMs can accomplish the flexibility that mine operators require to achieve cost-effective developments.Compact TBMs are achieving this acceptance because of the fundamental design of a shielded machine containing electrics and hydraulics within the forward shell, ability to achieve tight radius of curvature and grades, and ability to provide highly flexible support systems to meet all possible ground conditions.However, a single TBM design will not suit all mine developments, as each development method - while having common goals with all mine developments - will also require certain unique criteria to be fulfilled.

Jan 1, 1993

By P Radulovic, W Y. Lui

The Mount Isa Mines (MIM) copper concentrator at Mount Isa processes both chalcopyrite ore from the MIM underground mine and rotary holding furnace (RHF) slag from the MIM copper smelter. There have been numerous changes to the processing practices since commissioning this concentrator in 1973. Current management of the concentrator extends from grinding and flotation to concentrate handling (thickening and filtration) and tailings disposal (fill plants, tailings thickeners and process water systems).Predominant mill feed through the concentrator is chalcopyrite ore. RHF slag is processed when concentrator production exceeds mined ore production. The chalcopyrite circuit has two stages of grinding in parallel lines (Line 1 and Line 2). Each line has parallel preflotation and rougher banks, combining into a common scavenger/retreat circuit (including regrinding) and common cleaner circuit. RHF slag may be milled in parallel with chalcopyrite, utilising Line 2 flotation roughers and a Jameson cell cleaner. All final concentrate produced is combined and pumped to the concentrate handling plant. The concentrate is thickened, pre-fluxed and filtered in hyperbaric disc filters. Fluxing specification is set by the copper smelter, and filtered product transferred via conveyor belt to the smelter concentrate storage facility.Wet fill and paste fill plants utilise flotation final tailings as hydraulic or cemented hydraulic fill for stopes underground. Cement ratios and fill plant utilisation are varied depending on underground stope fill requirements. Tailings from the adjacent lead-zinc concentrator are also processed at wet fill. All tailings that are not utilised for backfill are pumped via wet fill to three parallel tailings thickeners. Thickener underflows are gravity fed to the tailings dams with thickener overflows recycled for site process water use. In addition to summarising historical operations, this paper will provide a detailed outline of more recent changes in the concentrator flotation circuit, equipment upgrades, reagent optimisation as well as product and process optimisation at the final concentrate handling and fill plants.CITATION:Lui, W Y and Radulovic, P, 2013. Mount Isa Mines copper concentrator - An insight into current and historical practice, in Proceedings MetPlant 2013 , pp 553-574 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 15, 2013

By L Y. Yang, Z Wang

This work presents the fundamental properties of CITIC magnetite concentrate and its performance in pelletising and sintering. CITIC concentrate has been widely used in pelletising to produce pellets for blast furnaces. It is also used in sintering to benefit from its sintering performance. CITIC concentrate has excellent balling properties owing to its size distribution, particle surface properties, large specific surface area and balling index, leading to strong green pellets and product pellets. When used in sintering at appropriate levels, sinter bed permeability improves, productivity is increased while coke consumption reduces, and sinter strength improves.

Nov 8, 2021

ADDRESS BY THE PRESIDENT OF THE INSTITUTE (MR. C. H. MARTIN) IN PRESENTING THE CERTIF1CATE TO SIR GEORGE FISHER, C.M.G.Members of The Institute, distinguished guests, of which there are many, ladies and gentlemen, you are welcome.And might I add a special welcome to Lady Mawby and Lady Fisher and to Sir George's only son Peter, who with his wife, Betty and one of Sir George's three daughters, Helen, are present this evening, and also to Sir Maurice's son, Colin, and Colin's wife, Jay, also in our company.The family presence must surely be a great source of pleasure and satisfaction to all those so intimately concerned.It is hardly. necessary for me to state the sole and only rC'l.son for our presence here tonight, which is to conJer on Sir George Fisher and Sir Maurice Mawby Honorary Membership of The Australasian Institute of Mining and Metallurgy, and at the same time to acknowledge two people who have rendered great service to the mining industry albeit tinged with sadness to all of us in the knowledge that from now on their influence may diminish.

Jan 1, 1976

By B Stewart

It has long been recognised that knowledge of the conditions existing in a mine after an incident is essential in deciding whether to deploy responders as part of the incident recovery process. Applying this knowledge in a structured manner to the assessment and the acceptability of the risks likely to be faced by those teams during response activities before authorising their deployment is an onerous task incumbent upon the person controlling the incident response. The Mine Event Management System (MEMS) provides structure and coordination in the management of mine events. It assists with the skills and knowledge for incident control teams to effectively manage any emergency or non-emergency event, be it large or small. In cases where multiple organisations are involved, the MEMS promotes effective joint operations through the use of common terminology and structure to provide seamless communication between agencies at all operational levels. The SQL-based software developed by Queensland Mines Rescue Service (QMRS) assists decision-makers to make considered options; it does not make decisions for you. When set-up, it allows the information that already exists within a mine’s Safety Health Management System that is relevant to the incident to be accessed and considered rapidly within the pressured environment of an emergency. Additionally, the incident specific questions contained within MEMS focuses the management team on gathering and assessing information relevant to the incident as it progresses. The software’s event log can be utilised as an auditable document for post incident investigation. The MEMS provides a process to properly consider the adequacy of the information available upon which decisions have to be made, to consider and acknowledge the hazards of the environments within or adjacent to which responders will need to work and to acknowledge and authorise the entry of responders into or to remain within a mine either during or post an incident occurring, once an acceptable level of risk is achieved.

Apr 16, 2024

In 1969, Queensland Mines Limited obtained two large Prospecting Authorities in Arnhem Land, Northern Territory, Australia. The Nabarlek uranium deposit containing some 12 000 t of U308 was discovered on one of these in June 1970. Mining and stockpiling of this deposit were completed in 1979 and processing to yellowcake, which commenced in June 1980, is expected to occupy an 8-10 year period. The continuation of exploration, essential for the company to become a longer- term producer, was inhibited in 1972 by a Federal Government "freeze" on exploration in Aboriginal Reserves in the Northern Territory. Subsequently, the procedure for explorers to gain access to exploration areas in Aboriginal land was radically changed by the proclamation of the Aboriginal Land Rights (Northern Territory) Act 1976. As a result of this Act and the associated administrative policies adopted by Governments, Queensland Mines Limited has not yet regained access to the exploration areas it formally held in the early 1970's.

Jan 1, 1986

By G Lane, M Bueno

In a recent publication (Bueno and Lane, 2011) the authors presented the analysis of a consolidated dataset composed by 137 autogenous/semi-autogenous grinding (AG/SAG) mill pilot trials. By comparing the measured data against theoretical specific energy consumption, the analysis indicated which circuit configurations were more or less energy efficient. However, the analysis has also indicated that the energy efficiency of each of the types of circuits vary significantly.There are numerous factors that contribute to the variations of energy efficiency of AG/SAG mill-based circuits, such as feed size distribution, recycle ratios and ore characteristics. In view of this, the present work accesses these factors individually and discusses what may lead a particular circuit configuration to be more or less efficient in terms of energy and costs.CITATION:Bueno, M and Lane, G, 2012. Key drivers of energy and cost efficiency in autogenous/semi-autogenous grinding circuits, in Proceedings 11th AusIMM Mill OperatorsÆ Conference, pp 113-118 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Oct 29, 2012

By C A. Foss, D A. Clark, D Hillan

While magnetic surveys are the most common geophysical method used in mineral exploration, magnetics and geology remain to be fully integrated quantitatively in iron ore provinces. Although high-resolution aeromagnetic data has been collected over prospective areas of the Hamersley Province, much of the information in the data sets has hitherto not been fully exploited due to a lack of suitable interpretation methods. Recent advances in the processing and modelling of magnetics in highly magnetic terrains, constrained inversion and 3D visualisation and understanding the magnetic properties of banded iron formations and iron ores potentially create the capability to generate realistic 3D mapping of magnetite and hematite concentrations over large areas. Initial processing of conventional total magnetic intensity data produces true potential field maps that are unaffected by local perturbations of the regional geomagnetic field direction by intense local anomalies. The true potential field can be converted into vector and tensor components, each of which emphasises different structural features of the geology. Scalar quantities derived from these components simplify interpretation, using new methods, developed by CSIRO and elsewhere, that are less sensitive to magnetisation direction. Preliminary interpretations allow interpolation between mapped units and structures and evaluation of remanence and anisotropy effects. Accurate modelling requires rigourous treatment of self-demagnetisation and magnetic interaction effects. Semi-automated constrained inversion, combining magnetics with available geological information and other geophysical data, can be utilised to generate models of disposition of major magnetic units and the 3D magnetisation distribution within them. The final stage of interpretation is to exploit the understanding of magnetic properties (susceptibility, anisotropy and remanence) developed over many studies by CSIRO, the University of Western Australia and others to convert the interpreted magnetisation distributions into 3D maps of magnetite and hematite contents, which are the quantities of direct exploration interest.CITATION:Clark, D A, Foss, C A, Austin, J and Hillan, D, 2015. Three-dimensional mapping of magnetite and hematite concentrations from reprocessing of detailed aeromagnetic data, in Proceedings Iron Ore 2015, pp 229–240 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 13, 2015

By T Mizuta, H Satoh, M Ogasawara, M Miyata, M Fukuyama

The Miocene Chichibu granitoids associated with the Chichibu skarn deposit are divided into North Body, South Body and Daikoku altered stock. Orebodies of the Chichibu skarn deposit are mainly distributed in the north-western part of the North Body and Daikoku altered stock. The North Body consists of magnetite-series granitoids ranging from tonalite to granodiorite and to monzogranite from the margins to the centre of the intrusion. The South Body consists of tonalite and granodiorite, and most of these rocks are also classified as magnetite-series granitoids. The Daikoku altered stock consists of a quartz diorite porphyry. The SiO2 contents of the granitic rocks of the North Body and South Body range from 61.6 to 70.7 wt per cent. During magmatic differentiation, Cu, As and Zn contents in fresh granitic rocks of the North Body and South Body increase with SiO2 content up to 63 wt per cent SiO2, and then progressively decrease with increasing SiO2 contents as SiO2 exceeds 65 wt per cent. Estimated pressure for the emplacement of the granitoids is about 0.5 kbars. Cathodoluminescence studies on quartz from those granitic rocks show that vapour rich two-phase fluid inclusions tend to occur in the core of quartz crystals, while halite-bearing poly-phase fluid inclusions occur in the margins of quartz crystals. The distribution of fluid inclusions suggests that fluid composition changed from low to high salinities during the growth of magmatic quartz crystals. Texture showing quartz crystals with an oval shape enclosed by radial aggregates of a mixture of fine-grained quartz, plagioclase and K-feldspar composing the groundmass of the monzogranite also suggests a pressure decrease during solidification of North Body. These findings show that high salinity fluids were present during magmatic differentiation and that Fe-Cu-Pb-Zn-Au-Ag skarn mineralisation of the Chichibu deposit was possibly associated with these high salinity fluids. An EXTENDED ABSTRACT is available for download. A full-length paper was not prepared for this presentation.

Jan 1, 2008

By Tomlinson R. C

There are two main aspects of coal preparation to which the operational Research Executive of the National Coal Board has applied computer models. The first is in the planning of preparation plants and the first part of this paper discusses Simprep, a computer package that was designed to help on these calculations. The other is the development of control schemes to improve quality control, and the second part of the paper deals with the development of simulation techniques for this purpose.

Jan 1, 1977

By D Felipe, G J. Harbort

In the past 40 years substantial changes have occurred in flotation machines. This has included increases in mechanical cell size to 630 m3 , significant changes to flotation column aeration design and widespread use of the Jameson cell and other pneumatic flotation cells. Over the corresponding period there has been increased used of machine characterisation measurements to benchmark and optimise flotation circuit performance. JKTech maintains a database of industrial flotation machine characterisation measurements. The database contains over 4000 entries and includes gas dispersion measurements, such as bubble size, gas hold-up and superficial gas velocity, cell dimensions and impeller tip speeds. Data comes from numerous operating sites and commodity groups, including gold, copper, molybdenum, nickel, palladium, lead-zinc, platinum, silica, phosphate, coal and iron ore. Flotation duties registered include flash flotation, preflotation, roughing, scavenging and cleaner circuits. Measurements have been conducted on a wide range of flotation machines from different manufacturers. This includes forced air machines, such as Outotec and Dorr Oliver, and self-aerated machines, such as Denver and Wemco. The database also includes substantial flotation column entries, such as the Microcel, Eriez/CMT Slamjet and Jameson cell. This paper describes the flotation machine characterisation database and discusses the variation between different types of industrial flotation machines, in operating production circuits.

Aug 24, 2022

By P A Ferenczi

The Proterozoic iron oxide related Au-Cu-Bi (Tenant Creek style') deposits at Tennant Creek can be classified as syntectonic polymetallic hydrothermal replacement type mineralisation. These deposits have characteristics in common with a number of other Proterozoic iron oxide (Cu-U-Au-REE) hosted deposits in regions which include Southeast Missouri, USA; the Kiruna district, Sweden; the Great Bear Magmatic Zone, Canada; the Stuart Shelf, South Australia; and the Wemecke Mountains, Canada. Similarities between these and Tennant Creek style deposits include: 1. Tectonic Setting: Formed at shallow crustal levels (

Jan 1, 1994

The Electricity Commission of New South Wales is the largest single user of coal in the State, burning some 8.5 million tonnes during 1972-73. This coal is converted in power stations into electrical energy which is then distributed throughout the State and supplies the electricity requirements of 99% of users in New South Wales. Barring any major change in energy consumption growth, or change in the current mode of power generation, the consumption of coal by the Commission is estimated to have a doubling period of from 10 to 14 years. Coal is used to generate up to 87% of the electrical energy sold, the balance being obtained from hydro gen- eration, mainly in the Snowy Mountains, and, to a much smaller extent, from diesel generation at Broken Hill. A very large proportion of this coal is consumed in pulverised fuel boilers in the Commission's power stations, located mainly on the various coalfields of New South Wales. Coal supplies are drawn from a large number of mines, some owned or controlled by the Commission, others being owned by public companies. The coals used, originate from at least ten different seams located in the northern, western and southern coalfields of New South Wales, and therefore have a wide variety of properties and characteristics. To ensure an adequate fuel supply well into the future, the Commission is continuously engaged in coal prospecting in various areas. Bore data is used in assessing coal reserves and is also the basis of economic studies for their possible future exploitation. The numerous coal cores obtained during drilling operations are carefully tested and analysed in order to assess their suitability for power generation purposes, and to provide data for the design and operation of boiler plant using these coals. In existing power stations coal deliveries are systematically sampled and tested for quality control, for pay- ment of purchases based upon certain quality parameters and to check for any possible plant operating or main- tenance problems that might arise from the use of the particular coals. Almost all the properties of coal that may be necessary in the Commission's work are obtained using standard testing procedures carried out by the Commission's chemists, in laboratories located at the various power stations or at its Central Laboratories in Pyrmont. Where specialised analysis or testing is required, this is ordinarily undertaken on a commercial basis by outside bodies, expert in the particular field. The significance of the various properties of the coal for use in p.f. boilers is outlined and related to their proper application to boiler plant design and to plant operation.

Jan 1, 1975

By V Ser, I Smit, C Robertson

Anglo American has been researching the potential benefits of inter-particle comminution techniques for several years. Inter-particle comminution has additional benefits in terms of milling circuit performance such as energy consumption and stability. This paper focuses on the flotation benefits. Inter-particle comminution leads to selective breakage, mineralogical analysis has shown that this leads to improved liberation of the valuable minerals. In addition to selective breakage, the relatively short residence time experienced in typical inter-particle comminution machines allows more efficient classification which contributes to a æsharperÆ product size distribution. The effect of particle size in flotation has been well documented in literature. In general, it is has been shown that there is an optimal particle size range for flotation, and that both above and below this range, flotation recovery is adversely affected. Results show that the narrow size distribution which results from inter-particle comminution improves flotation recovery. Furthermore, the absence of excessive fine gangue material which typically results from conventional fine (-75 ¦m) milling of talcaceous ores, can lead to 100 per cent savings in depressant consumption when such ores are subjected to inter-particle comminution. To-date, this technology has been evaluated on more than ten ores. This paper will focus on one set of results which demonstrates a number of common differences that exist between material that has been milled conventionally and using inter-particle comminution technologies, with emphasis on what the impact of these differences is on flotation performance. A pilot scale (200 kg/h) vertical roller mill (VRM) was used to produce the material, and the results shown will describe conventional laboratory batch, locked cycle and pilot plant flotation testwork.

Jan 1, 2005

By I R. F MacCulloch, K Jones

Pintail Systems, Inc, a Colorado USA based company has developed and commercially applied bioremediation processes for biological detoxification of cyanide compounds in mine waste. Site-specific microorganisms are isolated from spent ore, tailings or process solutions and augmented in the laboratory for cyanide oxidation, denitrification and metal biomineralisation. Biological processes typically treat complex contaminants (cyanide compounds, soluble metals and nitrates) in a fraction of the time of conventional remediation processes. Cyanide is used in microbial metabolic processes as a carbon or a nitrogen source. Biological detoxification processes applied at the end of mine life can end long-term liability and perpetual monitoring and containment. Case studies from commercial application and demonstration programs for the US Environmental Protection Agency will be presented in this paper.

Jan 1, 2004