Search Documents

By M A. Gontalves, A F. D C Varajpo, S A. Stachissini

Clays from the Santa Elena Peninsula, south-east of the Ecuador coast, were investigated with a view to identifying their main mineralogical, physical, chemical and textural characteristics as well as their potential for industrial use as adsorbents. Identified as calcic bentonites, two representative samples from the Tosagua Formation (Oligocene to Lower Miocene) were selected for acid activation trials. The selection criterion was based on the greatest amount of clay fraction (<2 ¦m fraction) associated with the greatest content of montmorillonite. For the activation treatments, HCl and H2SO4 solutions of 4, 6 and 8 N were used in a stirred glass reaction vessel with the clay sample under reflux during four hours at temperatures of 70¦C for HCl and 85¦C for H2SO4. Mineralogical analysis by X-ray diffraction (XRD), chemical analysis by X-ray fluorescence (XRF), differential and gravimetric thermal analysis and measures of density, surface area and porosity indicated the changes occurred in the crystal structure of the montmorillonite. The acid treated clays were utilised in trials of purification and decolourisation of soybean vegetable oil in a ratio of 2:100 (clay/oil) at 90¦C for 30 min, under constant stirring. After centrifugation of the suspension, the wavelength of the bleached oil was measured by UV-visible spectrophotometer and the bleaching capacity of the clays was determined. The best bleaching capacity of the samples was obtained with 6 N H2SO4 acid-activated clays. The bleaching capacity was compared to Tonsil, a commercial acid-activated clay and similar results between them evidenced the potential industrial application of the Ecuadorian clays to bleaching of vegetable oil.

Jan 1, 2008

There has been much debate in the past as to whether the Australasian Institute of Mining and Meteorology ("AusIMM") should issue valuation guidelines in addition to the ASX and NCSC requirements. My experience in preparing independent expert reports has been that "best practice" sets higher standards than any laws or requirements set out by the ASX and NCSC. This is where I see the AusIMM coming in.

Jan 1, 1989

The mining industry is quite often faced with declining selling prices for its products in the face of rising prices for the input cost resources that it uses. Blasting is a key activity within the mining system and has a vital role to play within the Mine to MillTM concept. It is therefore important that blasting makes a positive contribution to mine profit and productivity. There are several variables involved in considering the profitability and productivity of blasting. The rock types and structures, the bench height, the blast hole drill rig specifications, hole diameter, spacing and burden, explosive loading and initiation and blast size fragmentation. Productivity accounting is a methodology which is used elsewhere to give additional insights into the productivity and pricing factors that drive the financial performance of a business. Miners know intuitively that productivity and pricing influence costs and profit, but only with productivity accounting can the dollars involved be calculated. Drilling and blasting are part of a chain of unit operations in a mine. For an owner-miner, drilling and blasting would be considered as cost centres and a productivity accounting cost model approach would be relevant. On the other hand a contractor is likely to consider drilling and blasting as a profit centre, in which case a productivity accounting profit model approach would be appropriate. Both of these will be explained. The paper provides a basic outline of deterministic productivity accounting and demonstrates its application to blasting. Drilling and blasting data from a mine was obtained for a two-month period. The change in productivity and prices was calculated to obtain the dollar contributions from them towards the change in cost. It was determined that although there had been productivity dollar gains these were offset by larger pricing dollar losses, the net effect being that total drilling and blasting costs increased. The productivity accounting analysis gives the facts and the mine is in a position to establish priorities based on knowing the dollar contributions of each input used.

Jan 1, 2001

By Reynolds JO

This contribution by. The Australasian Institute of Mining and Metallurgy has three main thrusts. First, an Institute (and industry) view on academia and the need for more entrepreneurship at top academic levels, second the need to lift our technological game, and third, professionalism and the perceived role of mineral industry education. While I will deal with each of these separately they are of course inter- related and can be brought together under the frequently used, but insufficiently practised title, "communications". First then, The Institute and industry view of academia. There are some academics in the audience and I imagine they may wish to reply to my remarks with an academic view of industry. That is not unreasonable. Like all human institutions, academic institutions vary in quality and characteristics. Some are successful and some less so. Some historically are well renowned. Others that were once successful schools have declined. Lesser known schools have grown into prominence. What is it that sets apart 'good' highly regarded schools from those that are not so well regarded? It comes down to one main ingredient - "leadership". The strong mining schools in the past 100 years have been strong because they have had outstanding and clearly identified leaders. Strong clearly identified leadership has always had rapport with, and the support of the industry. The two go hand- in-hand, each nourishing and supporting the Other.

Jan 1, 1986

In 1965, Peter Flawn author of the famous text-book on Mineral Resources (1966) published a paper in Economic Geology with the delightful title `Who took the `Economic' out of Economic Geology?'. He opened this most interesting article with the following paragraph:If one were called upon to cite an example of a fish out-of-water he could hardly pick a better one than a recent graduate of geology of an America university who is suddenly faced with the responsibility of evaluating or appraising a mineral property. And I venture to say that the 'ftsh' with a doctorate - even in economic geology - is not much better equipped than one holding a lesser degree. The new graduate with a major in economic geology probably knows the significance of the various sulphur isotopes, he surely knows a great deal about the chemistry of the ore forming fluids and he recites with ease the arguments which prove deposits are epigenetic rather than syngenetic. However he is a rare bird indeed if he knows anything about the economics of the mineral industry. The truth is that geologists who are engaged in evaluation work are largely self taught. I ask my more distinguished and experienced colleagues - `Has it always been this way? Who took the `economic' out of economic geology?

Jan 1, 1993

By K McSweeney, A Marton

This paper discusses the development of a strategy for ensuring long-term geotechnical stability of final pit walls at AngloGold AustraliaÆs Sunrise Dam Gold Mine. The strategy makes use of improved blasting techniques, changes to the mining sequence and other geotechnical techniques. Only the blasting techniques will be discussed in this paper. These were developed from numerous trials over a period of several months from May 2003 through to November 2003. The focus was to reduce crest loss damage and thereby improve final wall integrity, maintain designed safe berm widths, and ensure long-term stability. Crest loss mechanisms are now understood and are explained in this paper. The preferred solution is outlined; which is a combination of improved blasting and changes in the mining sequence to cater for pre-existing ground conditions. These ground conditions include dynamic hyper saline water with sometimes intersecting steeply dipping discrete structures. Project requirements were defined as mitigating or eliminating crest loss using 127 mm diameter pre-splitting and targeting minimal production blasting vibration levels against the walls. Blast results were measured by post blast visual inspections and video. Blast design input utilised the predictive algorithms built into simulation software when attempting to minimise vibration levels against the walls. Protection of the already fired pre-split line is now achieved using small charges against the wall and timing sequences which form a mask for the later firing main charges. The pre-split spacing is now modified to suit the geology. There eight blast domains identified around the perimeter of the pit, each having varying joint orientation. In addition, blasting the bench adjacent to the berm crest has particular considerations not required by the middle and lower benches. The preferred solution was to purposefully translate this damaged top section of the pre-split bench into a planned subsequent dig zone. The design of this top æweightÆ is a direct response to the nature of the crest loss mechanism.

Jan 1, 2004

I propose to speak today about our mineral heritage. In common usage "heritage" refers to the past. It means the discoveries, the developments, the mines and the processing plants, the benefits, the consequences, and the human experiences flowing from these. The history of the industry, inseparable from the history of the countries in which The Institute operates, is a rich background of which we can all be proud.But there is also a much wider meaning to mineral heritage. Our past has left us with the ab\lity to create and operate world scale enterprises generating wealth for the community, the ability to offer satisfying and challenging careers in a wide range of skills to our young people, and the willingness to follow adventurous and challenging vocations in remote areas, away from the big cities, at a time when the mentality of many is to get the most for the least effort and at the least inconvenience to themselves. The industry continues to be the repository of the pioneer spirit and a vital contributor to improving the life of the people in our countries.Thus, while our mineral heritage has much to do with the past, an essential part of it is how we use this rich past to build and shape our future. It is in this broader context that I am speaking today.

Jan 1, 1990

By J A. M Luz, A T. Bernardes

HukkiÆs law is an empirical law, which does not take into account several events of energy loss during the fragmentation processes. Since experimental results are very difficult to obtain, for a large range of fragment sizes, the verification of the law is very difficult. The relation between fractures and fragmentation processes with fractal geometry was proposed some decades ago. Empirical laws known in this context show basic features of fractal geometry, mainly self-affinity and power law behaviour. Thus, in this work a model was developed to simulate the fragmentation process and to check the relation between energy consumption and fragment sizes. The model is represented on a regular lattice. Links can represent pathways for fracture processes. The events of fragmentation have energy given by a probability distribution function. In the model there is no mass loss. Propagation of fractures occurs as self-avoiding random walks on the regular lattice.

Sep 26, 2011

By C X. Zhang, W K. Ru, S C. Hu

To study the creep properties and the energy evolution characteristics of the weakly cemented rock (WCR) in western China, the creep deformation damage law of weakly cemented mudstone (WCM) under graded loading and the energy evolution characteristics of each creep stage were analysed based on the triaxial graded loading creep test of WCR. The results showed that as the confining pressure increased, the creep failure strength of the WCM increased from 9.5 to 24.8 MPa, and the relative displacement of the mineral particles in the mudstone increased gradually, resulting in a reduction in the fracture angle from 79.7° to 58.3°. At the same stress level, the strain energy Ue, the total energy U, and the dissipation energy Ud all increased as the confining pressure increased, but the growth rates of U and Ud decreased gradually, while the growth rate of Ue remained high. At the end of the stable creep stage, Ue increased slowly with the confining pressure, while U and Ud increased rapidly with the confining pressure, and their growth rates were basically the same. At the end of the accelerated creep stage, the growth trends of these three energies were all positively correlated with the confining pressure, Ue was significantly lower than that at the end of the stable creep stage, and Ud and U were further increased. These results revealed the unique creep properties and energy evolution characteristics of the WCR, providing a theoretical basis for long-term stability control of roadways that are built with WCR.

Nov 29, 2022

THE alkaline method for the estimation of zinc cannot, in the writer's opinion, be relied. upon to within very narrow limits between two assayers on unknown quantities of zinc. The end point is not decisive enough, and allows the personal factor toenter largely into the assay. The following investigation was undertaken to see how accurate the acid method is on Broken Hill concentrates and ores, and what should be the limit between the results of two assayers. The method adopted is as follows:Weigh sufficient amount of ore to give titration (between 20 and 50 cc.), place in tall 400 cc. beaker, cover, add 7 cc. nitric acid and heat till brown fumes cease to be evolved. Wash dock glass into assay, add potassium chlorate, evaporate to dryness on a slow fire with the beaker uncovered. When no smell of chlorine or nitric acid is observed, remove and cool. Add 100 cc. boiling water, then 7 grm. ammonium chloride, W cc. ammonia (.880 sp. gr.), boil for five minutes, filter, wash...

Jan 1, 1911

For too long we, as an industry, have borne the brunt of irrational claims, poor science and even worse, journalism with regards to our affect on the environment. To some of us, the overwhelming media attention on greenhouse warming, the polluting outputs of mineral processing or unthinkable depletion of natural resources has left us embarrassed and more unfortunately has turned bright young people away from a career in the minerals industry.This paper shows the hypocrisy associated with an element of the green movement and dispels some general myths on mining disseminated by radical environmentalists.The fallacy of the greenhouse warming effect will be scrutinised by common sense and the mining industryÆs use of land will be discussed and put in proper perspective.Problems associated with safety and emissions and the means to overcome such are discussed briefly.

Jan 1, 2004

By A N. Terblanche, D S. Smit

The paper discusses the improvements achieved after an external sparger flotation column, 1.42 m diameter by 9.5 m high, was installed as a re-recleaner unit at the Northam Platinum LtdÆs UG 2 plant in South Africa. The paper also evaluates the pilot plant data prior to the industrial size column installation as well as the accuracy of scale up from pilot to full-scale operation. Since the installation of the PrepQuip flotation column, the final concentrate upgrade ratio improved from 83 to 105, the 3PGM+Auå recovery improved from 79.7 per cent to 81 per cent and the Cr2O3 content in the final concentrate decreased from five per cent to 2.8 per cent. The upgrade ratio can be improved to 125 with an overall 3PGM+Au recovery of 80 per cent. Conventional mechanically agitated flotation cells achieved only 74 per cent recovery at an upgrade ratio of 125.

Jan 1, 2005

By Hughes CA

The need to recover metals from low grade deposits, old tailings, etc., combined with improvements in equipment design and the development of new extractants, has resulted in solvent extraction (SX) metal recovery reaching new importance (Webster & Ferron, 1993). The basic principle of solvent extraction is the use of an equilibrium system in which a metal ion is transferred from an aqueous phase into an organic phase, (Equation 1), (Ritcey, 1984). M + E ME . (1) The organic extractant (E) is usually specific for a certain metal ion (M) and forms a metal complex in the organic phase, leaving the impurities behind in the aqueous phase. To recover the metal, the equilibrium is reversed and the metal ion is transferred back from the organic to another aqueous phase in a process called stripping. The metal is then recovered from the aqueous strip solution, usually by electrowinning.

Jan 1, 1990

GRD Macraes Limited, owners and operators of the Macraes and Reefton Gold Project in New Zealand, have taken up the challenge of sustainably producing in excess of 300 000 ounces per annum within five years.GRD Macraes is well on target to achieve the forecast of 170 000 oz at a cash cost of A$310/oz for the 2002 financial year, with our Reefton operation set to add about 70 000 û 80 000 ounces per annum from late 2003.At the end of 2001 GRD Macraes Limited had resources of 5.5 million oz with reserves at 2.8 million oz.

Jan 1, 2002

By J L. Merritt

The mining industry seeks to engage with and respond to stakeholders through open consultation processes during the various phases of a mining project (Department of Industry, Tourism and Resources, 2006). Two Australian Coal Association Research Program (ACARP) funded projects conducted in the Bowen Basin coalfields in Central Queensland investigated the use of a stakeholder panel for the evaluation of mine site rehabilitation. The panel members were drawn from the local and regional area, and represented neighbouring landholders, traditional owners, AgForce, local government, conservation groups and non-governmental organisations (NGOs) such as Greening Australia and the Fitzroy Basin Association. The approach of utilising stakeholders to establish rehabilitation criteria was proposed as an alternative to the established practice of assessing rehabilitated areas against a suite of quantitative completion criteria; eg >70 per cent vegetative ground cover or <5 t/ha/a soil loss. The basis of this approach recognises the reality that the definition of completion criteria has proved problematic over the last 40 years with no broad consensus reached on the suite, let alone the metrics; eg the exact cover level that will benchmark acceptance of the mine site rehabilitation.CITATION:Merritt, J L, 2016. Zooming out – learning to see rehabilitation through stakeholders’ eyes, in Proceedings Life-of-Mine 2016 Conference, pp 163–165 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jun 28, 2016

By Restarick C, Jowett A

A cylinder-cyclone system, fitted with a flow control valve between the cylinder and cyclone plus in some tests a variable cyclone spigot, has been used to achieve classifier separations at unusually coarse sizes relative to the diameter of the units used. The method has proved to be useful for low tonnage flows at low pulp density and variable feed rate. The system relies on use of a cylinder unit to reject excess water and fine particles, the amount rejected being adjusted by the flow control valve. The valve also adjusts flow rate and pulp density of feed to the cyclone unit, and can be adjusted to give a separation at a coarse particle size. The system has been used in connection with experiments on the pilot plant at Mount Isa, where a 76 mm system was used to classify feed to the lead secondary rougher circuit at sizes as coarse as 52 micrametres galena equivalent for split conditioning tests. Further tests have been carried out with quartz to assess the range of size separations Possible.

Jan 1, 1978

By Fraser RJ

A Robbins Raise Drill Model 61R was used to provide one 7' diameter shaft 1050' deep in Clutha Development's exploratory mine at Blackwater in Central Queensland and two 7' diameter shafts 1450' deep at their South Clifton mine on the Illawarra Coast of New South Wales.

Jan 1, 1972

By D Trembath

"One of the key risks to the success of a mining operation is the accuracy of the estimates of both the economic mineral and any accompanying contaminants contained within the ore reserve. Misrepresenting the mineralogical characteristics of the ore reserve can result in considerable financial investment in an operation that is in fact uneconomic and/or carries a significant environmental risk. This in turn can result in an unplanned closure of the operation with associated financial, environmental and social legacy. One way to minimise this risk is to undertake high density resource sampling to gain a better understanding of the resource characteristics. However, such an approach is expensive, time-consuming and often impractical. The risk of not having an accurate model is typically assessed during a feasibility study utilising a Monte Carlo simulation method or some form of sensitivity analysis. Importantly, the error margins used in these types of analyses are often based on subjective or very general criteria such as ‘professional judgement’ or an ‘industry standard’. This presentation introduces a conditional simulation method for developing a range of mineralogical distribution models. Based broadly on the method outlined in Journel and Kyriakidis (2004) the proposed approach develops this work further. It combines a geostatistical analysis of the available data with automated mine design software to provide a rigorous method for assessing the confidence in the mineralogical characterisation of the ore reserve. The process is based on simulating possible mine plans based on the statistical characteristics of the available resource sample data. These plans are then assessed against high resolution resource models generated using a Sequential Gaussian Simulation method. The outcome is confidence intervals for important characteristics of the ore reserve estimate relative to the actual resource. These confidence intervals are an objective and transparent measure important for assessing closure risks and represent an improvement over common practice.CITATION:Trembath, D, 2016. A simulation approach for improving the assessment of closure risks, in Proceedings Life-of-Mine 2016 Conference , pp 36–38 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Jun 28, 2016

Although a small quantity of lc,;v viscosity index ' (L.V.I.) oils are presently manufactured in. Australia, lubricating oil refining methods are assuming gxeater significance since in 1964 Australia will be locally refining the bulk of its requirements and some companies may be exporting a surplus. New plants are ' planned to refine mainly high and medium viscosity index oils from imported crudes and the paper describes typical techniques used òto: produce. thes& oils. .

Jan 1, 1962

By R Urie

Dilution and loss of ore during the mining process invariably occur in all underground mining operations. This dilution and ore loss can have a significant effect on the performance and value generated from a mining operation. Further, excessive dilution or greater than anticipated ore loss during mining is often one of the key reasons for the underperformance of a mining project when compared to a feasibility study or annual budget. Mining professionals often go to great lengths preparing detailed mine plans, schedules and economic models only to then apply high-level estimates or rule of thumb values for dilution and mining recovery that can ultimately lead to inaccurate forecasts for the performance of a mine with the resultant loss of value due to the mining of uneconomic material or the loss of potentially valuable ore. This paper discusses processes and practices that can be practically used to manage dilution and mining recovery in an underground mining operation with a focus on understanding and then maximising value. The processes cover items such as the definition and measurement of dilution and mining recovery, techniques for the estimation of dilution and mining recovery, consideration of the economic implications, management of dilution and mining recovery through the stages of the planning cycle, and practices to reduce dilution and improve mining recovery. Common misconceptions and omissions are also discussed.

Mar 29, 2023