Search Documents

The issue of fine coal and tailings dewatering has become of increasing concern to many coal preparation operators, both in Australia and overseas due to a variety of factors. Increasing mechanisation and mining of thinner seams over the past decades has resulted in an increasing amount of fines generation while increasing international trade in coal and tighter environmental constraints on tailings disposal have resulted in the production of these same fines to be an increasing problem. However, technology to date has not always been able to supply a cost-effective solution to the handling of these fines in an efficient and environmentally benign manner. This paper will review the key issues associated with the dewatering of fine coal and tailings, will describe the major current practices and constraints, and finally will indicate alternative technologies that may have to be considered in the near future. For the purpose of this paper, "fine" coal is described as that material less than 0.5 mm in diameter (as this is the most common cutpoint between various plant circuits in Australian practice), although the technological constraints are very much dependent upon the fraction less than 45 micron. The amount of minus 0.5 mm material fed to plants varies, depending upon the type of coal and mining operation, but in Australia may range from less than ten per cent to greater than 30 per cent of the feed in higher rank coals.

Jan 1, 1991

By R Hoeppel, D Harimon, A Fisher

This paper examines the importance of examining the relationship between biology and geochemistry when designing a biopile to treat alkaline soils impacted by petroleum hydrocarbons. At a site in Nevada a large, unlined pit was constructed in a loamy sand soil and filled at regular intervals with a mixture of jet fuel, lubricating oils and waste solvents which were set on fire by the local fire department for training purposes. During its period of operation numerous chemicals were also dumped into the pit for disposal purposes, including dichlorobenzene and various chloroethylenes. As a result of these activities a large groundwater contaminant plume was formed. As a part of the site remediation process a decision was made to perform a limited source removal and excavate the top three to four metres of contaminated soil from the burn pit and place it in an engineered biopile. The location of the training pit is in a heavily mineralised basin where the background sulphate level in groundwater exceeds 5000 ppm. Due to naturally occurring biodegradation of the petroleum hydrocarbons a large portion of the sulphate was converted to sulphide which deposited in the soils as marcasite in the anaerobic soils. The initial attempt at soil remediation was to use a forced air treatment scheme that had worked well in small scale laboratory testing. Unfortunately, when attempted in the field on a large scale, marcasite reacted with atmospheric oxygen resulting in internal biopile temperatures exceeding 90¦C resulting in the virtual sterilisation of the soils without remediation occurring. In order to solve this vexing problem Pintail Systems, Inc developed an anaerobic culture that allowed the pile to be operated under anaerobic conditions. Within three months the biopile successfully demonstrated on a large scale significant biodegradation of the refractory petroleum hydrocarbons.

Jan 1, 2004

This paper forms part of a series of papers relating to the Melbourne Underground Rail Loop and presented to the Fourth Australian Tunnelling Conference in Melbourne, March 1981. The Design of Electrical and Mechanical Services in Museum Station and adjacent Running Tunnels and their relation to Rail.wruy Operation through the Loop are described. The descriptions, while specific to Muscrio Station, are generally representative of those being provided at Parliament and Flagstaff Stations. The Museum Station comprises some 6500 square metres of platform and track area, 5000 square metres of booking hall concourse and entrances and 1200 square metres of offices and plant rooms. The Mechanical and Ilectrical Services for this complex are .imilar in many aspects to those of a large !.gr.hrise city building, but in general the i::;ign is directed more strongly towards :.arety, durability and reliability, and subject to many restraints imposed by L'mitations of space and accessability.

Jan 1, 1981

Escondida is a state-of-the-art copper mining operation. It is the major copper project of the 1990s and is the largest new investment in the industry - a US$823 million project. It accounts for about six per cent of Chile's total exports, making Escondida the largest private exporting company in Chile.

Jan 1, 1992

By Krzystanek Z, Wasilewski S

The problem of automatic control of a coal mine ventilation network is discussed. It is found that the structure of the control sys-tem should have two levels, i.e. local regulation of ventilation para-meters (air flows) in faces to eliminate the effect of quick disturba-noes, and supervisory control of the whole ventilation process by pe-riodical modifications to the working characteristics of the main fans. Practical and theoretical problems connected with implementation of the system in Polish mining are listed and discussed. To solve these prob-lems a series of experiments with air flow control in three different coal faces were carried-out with the aim of checking the measuring and control equipment in a real mine conditions as well as investigatingthe gasodynamics of the ventilation process. The results of the experi-ments are analysdd, and used to verify the mathematical model of the gasodynamics of a longwall face.

Jan 1, 1985

By Tsuchiya N, Takada Y, Okabe K

Alkalis in the blast furnace are removed mainly by the slag, Alkali removal by the slag was studied as a rate process of alkali vapor- ization from the slag flowing through the dropping zone in the blast furnace. The vapor-, ization rate of I:20 from CaO-Si02-A1203 IZ20 slag was- measured under various experimental conditions. An empirical formula for the vaporization rate was obtained as a function of slag basicity, temperature and surface area per unit mass of slag. A simulation model of IC20 vaporization in the dropping zone was evaluated using the rate equation when the true velocity and surface area of the slag was de- termined from a flow dynamic model of counter- current gas-liquid flow through packed beds. The influence of the dynamic conditions of flow, as well as the slag basicity and temperature, on alkali removal by the slag was estimated.

Jan 1, 1980

By Pollard D, Meadows N

The presence of impurities which are electropositive to zinc in acid zinc electro- lyte causes changes to deposit morphology and reduced current efficiency. Glue may be added to control some impurity effects, but assaying for animal glue concentration is difficult and seldom done. Measurement of the activation overpotential for zinc deposition by cyclic voltammetry is used in some plants to monitor electrolyte quality and control glue additions. The deposit morphology and current efficiency of zinc deposition from commercial electrolyte were investigated for various glue additions in the presence of increased levels of antimony. Cyclic voltammetry was invest- i,ated as a method of optimizing glue additions in the presence of antimony. Scanning electron microscopy showed deposits characteristic of the impurity element present and the glue addition rate. Cyclic voltammetry measurements showed some correlation between current efficiency and activation polarization potential. The importance of using tankhouse electrolytes where results are to be related to tankhouse operation was noted.

Jan 1, 1984

By Glastonbury J. R

The kinetics of the direct chlorination of, zircon in the presence of carbon was studied at temperatures between 9000C and 12000 C. From the experimental data it is prop- osed that the most likely mechanism for metal oxide (MeO2) chlorination is as follows: At I Surfaceon zMeO2+ZMeCl - MeOC12 (1) At Carbon MeOC12+C+Cl MeC14+CO (2) Surface It.is envisaged that this type of mechan- ism would occur for both the zirconium and, silicon. constituents of the ore. In the above mechanism; the surface re- actions appear to be fast and not rate controll- ing. In a carbon surface deficient bed the diff- usion of oxychloride intermediate through the boundary layer to the carbon surface becomes the rate controlling step. In a zircon surface deficient bed the diffusion of oxychloride away from the zircon surface controls the reaction. This postulated mechanism can be used to ex-, plain the observed experimental effects.

Jan 1, 1973

The interfaces between the Broken Hill ore lenses and the enclosing wallrocks are, on a broad scale, parallel to metamorphic layering in the wallrock gneisses and quartzites. In detail, however, the concordant contacts are interrupted by piercement structures, formed by plastic injection of ore into the wallrocks during metamorphism.These discordant bodies vary from minor projections measuring less than I m long, to major ore shoots ("droppers") as much as 60 m long. The intrusive bodies consist of fragmented ore and wallrock in amatrix of recrystallised sulphides. Wallrock fragments have been altered to manganese-rich and calcium-rich mineral assemblages. The injected ore is enriched in sulphides compared with the parent ore, and there has been enrichment in a number of minor elements.Piercement structures formed during the waning phase of high grade metamorphism, when incompetent ore was injected plastically under pressure into the wallrocks, particularly at fold crests. Adjacent to the "droppers", retrograde schists developed as a result of shearing along the ore-wallrock interface.

Jan 1, 1976

By A Turns

In a survey conducted by symplexi with underground miners in Australia; 78 per cent of participants believed that ‘safety’ is all about people. If ‘safety’ is about people, then is the mining industry focusing on the wrong thing? It would be fair to say that the mining industry is heavily systems focused. Companies develop a safety management system and use this to show regulators that they comply with legislation – however, that is only half of the picture.

May 5, 2022

Classifications of Ni-Cu deposits are based on petrology, geochemistry and the geotectonic setting of host igneous bodies (Naldrett and Cabri, 1976; Besson et al, 1979; Nadrett, 1989). The four major classes in Naldrett's (1989) division rest on the geotectonic setting of the igneous complexes and the classes are further subdivided on the basis of the petrology and geochemistry of the intrusion. A more common subdivision of mafic and ultramafic igneous rocks is based on the environment of rock-forming processes, endogenic or exogenic, intrusive or extrusive, and this subdivision has been applied, in practice, to the classification of sulphide Ni-Cu deposits, too. The extrusive deposits, Class I in Naldrett's (1989) classification, are directly related to volcanic processes whereas all the others refer to the intrusive environment. This paper looks at the differences between the extrusive and intrusive groups of Ni-Cu deposits and presents generic, genetic and structural features of the intrusive group.

Jan 1, 1996

The methodology (i.e. procedures) used in testwork for modifying, improving, selecting, designing or developing processes is reviewed and possible improvements described. Minerals and particles could be characterised more comprehensively with modifications of existing procedures. Identification of the dominant phenomenon in a process could help bring the results of laboratory tests closer to plant performance. Improvements in pilot plant testwork could reduce the frequency and magnitude of problems in materials handling and separation in production processes, and increase the quantity and quality of the data obtained from a limited number of tests. Longer-term improvements in methodology depend on some changes in basic research. Information is required about all of the phenomena that occur in a production process rather than sophisticated models of specific phenomena. Theories, correlations and computer simulations could be used more effectively in testwork if they were simple, capable of forecasting the effects of changes and applicable to a number of similar processes.

Jan 1, 1986

With the burgeoning opportunities for new gold mines to be developed the opportunity now exists for a reassessment of the optimal processing path for these gold ores. Projects have traditionally followed the path of whole ore cyanidation with either Carbon In Pulp (CIP), Carbon In Leach (CIL) or Merrill Crowe. The challenge ahead is whether these traditional processing methods are the best option for stakeholders, or to go beyond CIP and use a combination of currently available technologies that can be used to provide gold recovery at a significantly reduced capital cost and minimal deleterious impact on the environment. Either stand alone or combinations of gravity concentration and flotation, can produce a gold bearing concentrate that can then be fed directly to a batch or continuous intensive cyanidation unit. Treatment of a gravity/flotation concentrate by intensive cyanidation may be processed by the InLine Leach Reactor (ILR) developed by Gekko Systems of Australia. The advantages of the technology combining gravity/flotation followed by intensive cyanidation are significantly reduced capital costs; improved safety due to reduced cyanide inventories; the majority of tailings un-contaminated by cyanide; less energy required due to an opportunity for an increase in grind size û reducing green house gas emissions; detoxification of concentrate tailings can minimise tailings disposal and containment requirements.

Jan 1, 2004

Adsorption isotherms, zeta potential and coagulation techniques have been used to exa- mine the mechanism of metal activation on SiO2 and ZnS surfaces. The importance of surface nucleation or precipitation of metal hydroxide coatings is'established and identified-by characteristic charge reversal patterns. The significance of surface coatings in sulphide and non-sulphide flotation is discussed.

Jan 1, 1973

As part of the response to the increased demand for products such as iron ore, coal and gold many resource companies have identified the need to develop strategies focused on attracting high demand professionals and retaining current employees in the business. Recent graduates are entering a time where they can expect high starting salaries, attractive benefits and lifestyle options. At the same time high work expectations and large demands on both personal and professional development will also be the norm. Some of the challenges faced may include high demands on performance, working with limited resources, long hours, and tackling unfamiliar areas of work with little guidance. However, managing your career and these challenges effectively can give you valuable experience in a short amount of time. By offering situations from my relatively short, yet active, career in the mining industry during these boom times I will raise some key points on how to best leverage your commodity and make the most of a bullish market.

Jan 1, 2006

By P G Simpson

The Sundance gold mine, located 2.5 km east of the town of Batchelor in the Northern Territiory, has produced over 5300 oz of gold since it was discovered in 1978. Sundance is unique in the Pine Creek Inlier in that the ore is hosted in palaeo-karst detritus and crystalline magnesite of the Early Proterozoic Coomalie Dolomite. This paper presents a summary of the geology of the mine, and describes the methods used during the two periods of mining.

Jan 1, 1994

By Smit J. G

Following an increase in the number of methane ignitions in South African coal mines a new ventilation system was developed. The "Hydravert" system conceived in late 1979 for use in low seam coal mines, where the bord and pillar method of working is used, has been extensively developed to include applications for mining seams up to 4.5 metres high. A brief history of the development is supplied including some of the pitfalls encountered in the hydraulic equipment design and selection.

Jan 1, 1988

By G R. Hancock, D Verdon-Kidd, M J. Saynor, J B. C Lowry, T J. Coulthard

The ability to simulate the stability of post-mining landscapes over time scales ranging from decades to millennia is a critical element in the assessment of closure designs for uranium mines. Landscape Evolution Modelling (LEM) technologies provide a means to simulate and assess the long-term geomorphic stability of a conceptual rehabilitated landform for periods of thousands of years. However, a major issue with simulations derived from long-term modelling are the limitations associated with the data inputs. Specifically, simulations which utilise historic rainfall data only represent the variability of rainfall events that have occurred over a relatively short period. Consequently, these simulations run the risk of not accounting for the full range of rainfall variability that might be expected over an extended period of up to 10 000 years. Therefore, for this study a probabilistic approach was adopted to generate a stochastic synthetic rainfall data set to produce a series of unique rainfall scenarios, each representing a simulated period of 100 years. Importantly, utilising such an approach allows uncertainty in predictions to be better accounted for and provides a range or probability of likely outcomes.In this study, the effect of ten individual rainfall scenarios are assessed in terms of their impact on the predicted erosion and denudations rates produced by the CAESAR-Lisflood LEM for a conceptual rehabilitated landform of the Ranger Uranium Mine (RUM) in the Northern Territory of Australia, focusing on the Corridor Creek catchment (Figure 1). While legislation requires this site to be erosionally stable for at least 10 000 years (Commonwealth of Australia, 1987), here the focus is on the first one hundred years of landscape evolution, as this is the period in which erosion is expected to be higher, with limited vegetation cover or pedogenic development in the initial decades after rehabilitation. It is also the period where the drainage pattern is set.CITATION:Lowry, J B C, Verdon-Kidd, D, Hancock, G R, Saynor, M J and Coulthard, T J, 2016. Application of synthetic rainfall data to long-term modelling of a rehabilitated landform, in Proceedings Life-of-Mine 2016 Conference , pp 75–79 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jun 28, 2016

By J M TORLACH

Learning is an iterative process, and we might reasonably expect that after more than a century of mining during an era of sustained technological development, (following a millenium or two of unrelieved hard physical graft), that the more obvious physical hazards could by now be competently managed. It is perhaps a reflection on the perversity of human nature that we have not fully learned our lessons in this exacting environment, and that worse, we have still too often failed to profit by the experience of those lessons. The more obvious underlying factors which impact on this situation are examined briefly, as a prelude to consideration of some outstanding examples of recurrent problems experienced in recent years. Reasons for the continued existence of sub-standard practices are outlined, with a focus on the human element, and finally proposals for appropriate remedial strategies are summarised. This paper therefore seeks to examine and discuss some of our deficiences and to suggest some directions for the way ahead.

Jan 1, 1992

About 11,000 tons of contaminated zinc flotation concentrate were available in the form of earth walls from dams used for atmospheric drying of the concentrate.Following successful laboratory tests this material was treated in a plant by crushing, grinding, and then flotation in a circuit consisting of roughing, scavenging, and two stages of cleaning. Reagents used were copper sulphate and a little butyl xanthate and frother. About 5,720 tons of zinc concentrate assaying 52· 3 per cent zinc were produced.

Jan 1, 1968