Search Documents

By G Cormack

By designing comminution circuits for mineral liberation rather than the final recovery process and by using high mass pull gravity recovery, the concept of underground processing has become a reality. Gekko has found that many ores respond favourably to fine crushing with either high pressure grinding rolls or vertical shaft impactors which when combined with the InLine Pressure Jig gravity separator and coarse flotation results in a narrow, low-head, compact processing plant that can be sensibly fitted in existing underground openings. The focus on fine crushing reduces the power requirements of the plant to approximately 5 kWh/t for a capacity of up to 20 t/h run of mine ore feed. The use of water recycle systems places no extra load on the mineÆs normal water handling system. GekkoÆs underground processing plant, the æPythonÆ, has been designed to be towed down the decline or lowered down a shaft and is capable of being installed in sloping, non-linear drives for placement close to the working face. The overall benefit to mining companies of this concept has been estimated to be a significant operating cost-saving, lower cut-off grade and a significantly smaller environmental footprint.

Jan 1, 2008

By Showers JAF

The Western Mining Corporation mining lease on the Bendigo Goldfield measures 5krri x 18km with more than 20 anticlinal folds parallelling th long north-south boundaries. Numerous closely spaced shafts and extensive underground workings on the reef lines along the folds flooded with groundwater following the progressive abandonment of the field. Preliminary water sampling and assessment demonstrated that a major dewatering programme and acceptable disposal methods were necessary to dewater interconnected old workings in areas of interest prior to any underground work taking place. A field wide geohydolic investigation was undertaken to establish geohydraulic parameters, groundwater recharge rates and water qualities. Data from the field investigation together with estimates of the volume geometry of the submerged workings as obtained from old mine plans, production history, and limited pump testing results were used with an appropriate analytical model to obtain estimates of water discharge rates required to reach various dewatering targets. Water disposal options were limited by relatively high salinities, arsenic levels, contained hydrogen sulphide, and the mine locations within the urban areas surrounding Bendigo. Direct disposal to the surface drainage system could not be considered, treatment to acceptable discharge standards was not economically feasible, and it was necessary to adopt a strategy of collection, containment, and evaporation.

Jan 1, 1988

The experiments described in this paper were carried out as a preliminary to a comprehensive study of the factors which affect the behaviour of lead during and subsequent to deformation by rolling and pressing. These observations are therefore to be considered as introductory to a further paper dealing more specifically with the above-mentioned variables.EXPERIMENTALThe rolling was carried out in a small mill with six-inch diameter surface ground rolls, both of which were electrically driven at 15 r.p.m. The average draft per pass approximated 0·03 in. The pressing was performed between platens in the compression unit of a 30-ton Amsler machine. The flat faces used had a ground finish comparable with the surface of the rolls. All hardness measurements were made with a Herbert "dead load" Brinell machine. The following te'sting conditions were maintained: ball diameter-5 mm.; load-10 kgms.; duration of loading-30 seconds; temperature of testing-16 to 18°C. The hardness values which are given are the mean of two or more impressions made at corresponding positions on the test specimens.PREVIOUS WORKSince the researches of Tresca (1):j: into the nature of the plastic flow of metals during various forging and extrusion...

Jan 1, 1939

The sampling of a run-of-mine (ROM) ore with the objective of controlling the fundamental variance associated with the sampling step is a poorly understood subject. Finding the effective sampling constant by repetitive sampling to establish the variance between nominally identical subsamples of a given mass of the ore is a laborious, time-consuming and very expensive exercise. In this paper, the run-of-mine ore is modelled using three components: ore, waste, and relatively fine material which shows significant liberation of the mineral phase(s) carrying the target analyte. The expression for the sampling constant of the mixture is developed from first principles. The form of the equation provides insight into the factors that are important in controlling the magnitude of the sampling constant and hence the fundamental uncertainty associated with a given mass of sample. The controlling factors are shown to be the size distribution of the ore/waste mixture, the proportion of waste mixed with the ore and the extent of liberation and the size distribution of the liberated material in the finer fractions.

Jan 1, 2008

By Percival T. J

Precious metal deposits containing fine-grained disseminated or dispersed gold-silver form by reactions between metal-bearing hydrothermal fluids and sedimentary host rocks. Host rock permeability and chemical composition exert a primary influence on the fluid movement necessary for any primary dispersion halos to form around ore bodies, and determine whether a disseminated style orebody itself will even form. Where the mineralized rocks are relatively unfractured the margins of the orebodies exhibit abrupt decreases in gold content, and strong corresponding decreases in the contents of other metals. Primary dispersion patterns of this type are difficult to recognize and commonly are only a few meters (or less) in width. If the host rocks were well shattered and broken before mineralization, remnant amounts of the hydrothermal fluids may be dissipated in fractures lateral to or above the ore zones. This causes geochemical anomalies to form with clays and silt- size silica within the fractures over distances of up to at least 30-50 meters away from the main orebodies. The tendency for large primary dispersion halos not to form around these deposits explains the disappointing results from so many drilling programs where no multi-gram gold-grade material was even found: if large areas and apparent large volumes of rock contain one gram or less gold that likely is the "orebody" and not a halo effect around high grade mineralization.

Jan 1, 1988

By Weatherstone N

Ironstone outcrops on the Savage River were discovered by State Government Surveyor C. P. Sprent in 1877. The limonitic outcrops were initially regarded as the surface expressions of pos- sible tin-bearing lodes, the tin deposits at Mt. Bischoff to the east having been found in 1871. By the turn of the century, shafts, adits and trenches had been developed on the deposits in the unsuccessful quest for gold, silver and base metals. The deposits were first reported as a possible source of iron ore by Tasmania Department of Mines (TDM) geologists in 1919. Modern exploration began in 1956 with the area registering the best magnetic response during an aeromagnetic survey of North- western Tasmania by the Bureau of Mineral Resources (BMR). The area had previously been reserved by TDM in anticipation of the lifting of the iron ore embargo. Reconnaissance Geologi- cal mapping (TDM) and grid-based magnetometer surveys (BMR) indicated that resources of iron-bearing material could approach hundreds of millions of tons. This provided the incentive for two diamond drill holes funded by TDM which demonstrated iron mineralisation in substantial tonnages, suitable grades and, fol

Jan 1, 1988

The QSL continuous lead smelting process incorporates two basically different pyro- metallurgical operations: roast-reaction, smelting of galena concentrate, followed by carbothermic reduction of some by-product lead oxide slag. Both steps are performed simultaneously in separate compartments of a long horizontal cylindrical reactor, which is lined with fused chrome-magnesite bricks. This converter-type reactor contains a liquid bath consisting of a shallow layer of lead bullion with a superimposed layer of slag, the lead content of which is gradually reduced from about 50% to discardible levels. Metal relative to slag, and slag relative to the gas phase are in continuous countercurrent motion. A lead well is arranged at the flue end of the reactor, and an overflow tap for slag at the opposite end. Tonnage oxygen for oxidation and smelting of the charge, and sub- stoichiometric mixtures of pulverized coal and oxygen for reduction and heating of the slag, are directly blown into the bath using fluid-protected Savard-Lee injectors. High gas-liquid momentum transfer ensures intensive local mixing, and enables rapid mass and heat transfer.

Jan 1, 1984

By S Williams, N McBride

The aim of these analyses was to utilise the latest available production information for the Wandoo operation to determine the optimal blasting parameters, costing information and predicted results (fragmentation, muckpile shape and vibration). Much of the data used as input was made available from the information gathered during the excavation of the test pits during 1995. As with any æplanning stageÆ analyses, many assumptions were required to fill gaps in the available data. The calibration of computer blasting models was conducted using data from the last of the test pit blasts (this blast was carried out in material that closely resembled rock expected to constitute the bulk of the base case design pit). This calibration was refined using observation and experience based judgements to extend the accuracy of the predictions as far as possible. All the simulations were performed assuming that the blastholes will be wet (as instructed by BGM). This has consequently determined that the appropriate explosive for the simulations and the actual blasting will be a pumped emulsion/ANFO blend. The following blast design parameters were derived by determining a likely range of powder factor (from other similar scale gold mines) with a median value of 0.62 kg/m 3 being the powder factor arrived at through the field optimisation process conducted during the test pit excavation. The total swell/displacement percentage (volume after blast/volume before blast) largely determines the diggability of a well fragmented muckpile. Consequently where fragmentation is good any reduction of total swell will probably reduce diggabilty. Any reduction of diggability can and should be traded off against increased gold recovery. In most gold mines, diggabilty will be substantially compromised at the balance which produces the most profit. When these considerations are combined with the cost to drill and blast material, processing costs and the achievement of æacceptableÆ diggibility, the analysis becomes extremely complex and qualitative. Many trends are evident including:the relationship between powder factor (for each blast design) and maximum forward displacement (throw), see Figure 1; and the relationship between powder factor (for each blast design) and drill and blast cost per BCM, see Figure 2. The following blast designs are matched to each of three ore-tonnage alternatives (as supplied by BGM) (Table 1). They are all based on powder factor of 0.62 kg/BCM and are considered optimum from a mining æpoint of viewÆ. The costing of each design includes drilling, explosives and labour cost to load, stem and tie-in holes. Using the available rock data and relying heavily on the wall exposures in the test pit(s), it is the opinion of the author that between 20 per cent to 40 per cent of the final walls excavated in the Wandoo pit would be likely to have the angle between the dominant foliation and the wall plane that is well suited to presplitting and be cost-effectively served by presplit technique. The drilling cost for 125 mm blasthole is about $11.40 per drilled metre and the cost of 40 mm presplit explosive is about $140 per 25 kg (17 metre) case. This implies that the cost to drill and blast presplit on the above parameters would be about $10.90 per square metre of presplit face. The remaining wall area would be most cost-effectively delineated using modified production blasting techniques. This requires the use of modified parameters such as smaller hole diameters, smaller spacing/ burden, higher powder factor, free face firing, less rows per blast and longer delays. These altered blast parameters would usually be applied uniformly across the entire blast fired adjacent to the wall and this ætrimÆ blast would relieve burden away from the wall, into the pit. In simplest terms, this method relies upon maximised burden relief to minimise blast energy applied to the wall. It is only applicable where the material to be blasted is waste since the throw achieved is inconsistent with ore dilution control. The largest charge weight per hole for these analyses is 360 kg and the nearest domestic structure to the proposed Wandoo pit is about 6100 metres distant. From these parameters and assuming a worst case example of rock controlled site factor, the predicted ground vibration is 0.5 mm/sec that is about five per cent of the lower limit set down in AS 2187 part two (1993). This suggests that for the current location of neighbours, ground vibration will not be an issue for the Wandoo operation.

Jan 1, 1999

By R M. Briggs, I E. Smith, P M. Black, A B, R L. Brathwaite, J L. Mauk

The Hauraki Volcanic Region of the North Island developed between 18 and 1.9 Ma. Initial andesitic volcanism from 18 to 12 Ma was followed by 12 to 1.9 Ma volcanic activity that included rhyolitic, dacitic, andesitic, and basaltic compositions, with a gradual migration of activity to the SSE. Early andesitic volcanism evolved over the course of 8 m.y. to more silicic compositions; this trend was reset and repeated by post-10 Ma andesitic volcanism. Early and later andesites are otherwise remarkably similar in trace element composition. Rhyolites have the most diverse compositions, suggesting a major role for crustal input in their formation.

Jan 1, 2007

By A Kuras

Segmental tunnel linings are becoming more common in Australia. One current project employing a segmental lining is the City West Cable Tunnel (CWCT) in Sydney. The project has been commissioned by Energy Australia and is currently being constructed by Thiess Pty Ltd. The project includes 1.6 km of tunnel boring machine (TBM) driven, segmentally lined tunnel. The majority of the CWCT will be excavated through Hawkesbury Sandstone. The tunnel is required to carry a 132 kV electrical circuit under SydneyÆs central business district (CBD), between Haymarket and Energy AustraliaÆs City North Substation on Sussex Street. The segmental lining has been designed as a 3.2 m internal diameter, 200 mm thick universal ring with six trapezoidal segments. The design and detailing of this segmental lining presents some noteworthy challenges, including exposure to saline groundwater, and the exclusive use of steel fibres for flexural and tensile concrete reinforcement. This paper describes some of the key elements of the segmental lining design. These include:the case for choosing segmental linings over other forms of tunnel construction;the major design checks required of a segmental lining including ground loading, hydrostatic loading, joint bearing, joint rotation, ram loading and the early strength lifting case;the benefits of using steel fibres over conventional steel reinforcement;the design approach used for steel fibre reinforced concrete;the application of 3D computer modelling in the design;the provision for components including connector dowels and gaskets;the design for passive fire resistance; andthe design for durability of steel fibre reinforced concrete in a saline environment. Segmental lining design requires the application of specialist design approaches. Input is required by the construction team, as the methods of demoulding, handling, transportation and installation impact on the lining design. As the segmental lining is functioning as immediate ground support and also a permanent lining, high standards of manufacture and construction quality control are required to ensure that the 100-year design life is met. The requirement for a watertight tunnel means that detailing and installation of the EPDM gaskets is of importance.

Jan 1, 2008

By S Meffre, S Golding, K Zaw, J McPhie, R James, S Suphananthi

The Chatree deposit is located in the central portion of Loei Fold Belt, which extends from Lao PDR in the north through centralThailand to Cambodia in the south. Epithermal gold-silver mineralisation at Chatree occurs as veins/veinlets and stockworks with minor breccia in volcaniclastic and volcano-sedimentary rocks of andesitic to basaltic andesite composition and Permo-Triassic age. This preliminary oxygen isotope study mainly focuses on vein quartz of Au-Ag bearing mineralization (Stage 2) and a few samples of late Stage 4 quartz ¦ calcite veins. Quartz from Au-Ag bearing mineralisation has oxygen isotope values ranging from 8.1 to 12.3ë with the lowest values generally occurring at the deeper level (140 m below the surface). The late barren quartz ¦ calcite veins (Stage 4) tend to have higher oxygen isotope values ranging from 11.9 to 12.0ë. The oxygen isotope composition of the Chatree ore fluids were calculated at 250¦C, 300¦C and 350¦C based on homogenisation temperatures of fluid inclusions. The calculated oxygen isotopic composition of the Chatree ore fluid ranges between -1 and 6ë that overlaps with both meteoric and magmatic compositions. This shift in oxygen isotope compositions may relate to processes such as water rock-interaction and/or mixing of meteoric and magmatic fluids. It is interesting to note that the lowest quartz oxygen isotope values are spatially more or less confined to the prominent structures in the centre of the major ore zones. These structures may have been acted as conduits for higher temperature magmatic fluids. The quartz oxygen isotope values increase outwards from the centre of the main ore zones to the margin of the pits possibly due to mixing of magmatic fluids with lower temperature meteoric water. Whole rock oxygen and hydrogen isotope studies are in progress to investigate isotopic trends in the wall rock away from the ore zone. The systematic variation of oxygen isotopes in quartz from the mineralised veins and adjacent wall rocks could potentially be used as a vector to ore. An EXTENDED ABSTRACT is available for download. A full-length paper was not prepared for this presentation.

Jan 1, 2008

By T Mizuta, T Nakano, D Ishiyama

The Tamagawa Hot Spring, from which Ra-Pb-Sr-bearing barite precipitates, is a representative hot spring in a volcanic gas-bearing hydrothermal system associated with Quaternary andesitic to dacitic magmatic activity beneath the Yakeyama Volcano. Thermal water in the Tamagawa Hot Spring is divided into three types: Cl-SO4-type (Ohbuki hot spring: pH 1.2); SO4-type (pH 1.8 to 2.9); and neutral-type (pH 6.1). The concentrations of dissolved components in the Ohbuki Cl-SO4-type thermal water are about ten times higher than in the SO4-type thermal water. The 87Sr/86Sr isotopic signatures of the Ohbuki Cl-SO4-type thermal waters (0.703992 ¦ 0.000004 to 0.704032 ¦ 0.000006) are different from those of SO4-type thermal waters (0.704245 ¦ 0.000003) formed by the interaction of andesitic volcanic rocks (0.704065 ¦ 0.000007 to 0.704093 ¦ 0.000009) and groundwater derived from river water (0.704314 ¦ 0.000012 to 0.704519 ¦ 0.000013) in a shallower part of the hot spring area. The possible origins of Sr in the Ohbuki Cl-SO4-type thermal water and in the SO4-type thermal water are different. The Sr isotopic ratios (0.704130 ¦ 0.000012 to 0.707556 ¦ 0.000014) of Aniai Formation andPreYakeyama Lake deposits occurring below the hot spring area are distinctly higher than those of the Cl-SO4-type thermal water. However, it is expected that a solidifying andesitic or dacitic magma which has similar Sr isotopic ratios of the Ohbuki Cl-SO4-type thermal water, occur in the deep portion of the Tamagawa Hot Spring. The Cl-SO4-type thermal waters having low Sr isotopic ratios do not acquire their Sr isotopic signatures by interaction with strata below the hot spring area, but they are likely to reflect water interaction with a solidifying magma with low Sr isotopic ratios. Components including rare metals in Cl-SO4 type thermal water could be transported from a deeper part. An EXTENDED ABSTRACT is available for download. A full-length paper was not prepared for this presentation.

Jan 1, 2008

By J Emslie

Newmont AustraliaÆs Callie Underground Gold Mine is located on the Dead Bullock Soak Mining Lease, approximately 600 km NW of Alice Springs, NT, in the Granites-Tanami Goldfield. Dead Bullock Soak is part of NewmontÆs Tanami Operations, which also include the Granites Gold Mine and processing plant, Groundrush Open Pit and Tanami Mill. Callie is a world class Proterozoic gold deposit; production to date is in excess of 1.7 million ounces, with an additional Proved and Probable reserves at the end of 2002 of 10.8 Mt at 6.3 g/t. Gold mineralisation at Callie occurs in thin (1 - 30 mm) steeply dipping quartz-chlorite sheeted vein system that cuts across a 40¦ plunging folded sequence of medium to fine-grained metasediments. While the vein system is highly continuous, the gold distribution is highly variable and is controlled by the interaction of lithology, alteration, structure and vein density. The mineralisation is commonly coarse-grained and has a relatively high nugget effect, consequently the orebody is problematic to estimate and shows a high degree of sensitivity to drill hole density. Resource modelling at Callie is an example of a geologically driven model that has evolved with increasing data and understanding. Lithological and structural models are employed to define domains within which the grade estimation is undertaken using multiple indicator kriging. This gradual model evolution impacted greatly on the selection of the mining method. Uncertainty in the estimation of the orebody was a significant factor that led to sublevel open stoping with cemented aggregate fill being adopted as the mining method to improve extraction selectivity. Callie often shows strong positive reconciliation compared to the mill. The mine geologistÆs face the challenge of limiting the degree of underestimation of the core of stopes whilst ensuring that stope boundaries are not conservative. This can only be achieved through the mapping of subtle geological features in order to confirm the orebody model. The increased use of the geological mapping has improved our understanding of the controls on mineralisation and has been extended into the development of new models for near mine underground exploration.

Jan 1, 2003

Incidental to the progress of a geological survey of the Kalgoorlie goldfield during 1927-28 a number of specimens of telluride minerals were obtained, chiefly with the help of Mr. F. G. Brinsden, general manager of the South Kalgurli mine, and Mr. Ernest Williams, general manager of the Boulder Perseverance mine. This collection was supplemented by a number of small specimens, including the rare copper telluride, which were collected and preseryed from the Kalgurli mine by Mr. A. E. Paton, and also by a few miscellaneous specimens from the collection o{ Mr. S. F. C. Cook, of the Palace Hotel, Kalgoorlie.An extensive knowledge of the rare tellurium-bearing minerals was compiled during the last century from occurrences in Transylvania and Colorado. The recognition of different species has been based on chemical analyses and crystallographic measurements. In a few species there has been an absence of crystalline form, and these, together with the discoveries in this century of rickardite and "weissite" muthmannite and empressite, have depended chiefly on the chemical analysis for identification. On the other hand, the crystalline form of nagyagite and stiitzite has been described in detail, while their precise chemical formulae were doubtfully defined.

Jan 1, 1931

The U.S. Bureau of Mines has developed a prototype cross well acoustic logging system and complementary tomogr`aphic image reconstruction software for the detection and delineation of abandoned underground mines and associated subsidence failure in relatively shallow environments. The logging system uses a piezoelectric, cylindrical bender as an acoustic source. A triaxial accelerometer assembly, designed to be rigidly locked in the borehole, is the receiver portion of the logging system. Both the source and receiver probes operate at high frequencies, thus providing short wavelengths capable of resolving small features in most rock types. A modified van with a dual-drum wireline winch, 4-channel data acquisition system, power amplifiers, and waveform generator supports field operation of the logging system. A field study was conducted at a test site in San Antonio, Texas, to demonstrate the cross well acoustic logging system. The underlying rock at the test site is similar to stratified sediments in coal measures. First- arrival travel times were interpreted by tomographic reconstruction of the velocity field in the two-dimensional cross section between the source and receiver boreholes. The resulting image correlates well with geological borehole logging data for the test site.

Jan 1, 1992

By Shuqing L

The application of single liquid cement for fracture grouting in base rock may have history more than 120 years. The disadvantage of it is difficult to increase the grouting efficiency, because the jelling time of it is very long and hard to control. The double liquid grout, such as chemical grouts and cement water glass grout was developed at the end of 1960.'s Although the jelling time of this kind of grout can be controlled, it mast adopt double liquid grouting technology, use complicated equipment and is not easy to control component's ratio of the grout. Another disadvantage for chemical grout is high price, and have pollution to environment. OCE series single liquid grout is the effective grout material developed recently by making large efforts in Ohina. Main feature of it is that the jelling time is easy to control, materials from cement and clay are very cheap and without pollution to environment, and the grout can be injected by single liquid technology. The effect of QCE series grout has been proven by its application in China. It can be believed that QCE grout has great economic efficiency and will give a push to develop grout material.

Jan 1, 1988

EQUIPMENT TO BE DISCUSSED It is the intention of this paper to discuss the transporting of large skid mounted equipment and track machines around open cut mines. By large I mean 100 to 350 tonne capacity being trans- ported on minesite lowloaders and the capability of moving loads of 300 to 1200 tonne by other means. It is also possible to move larger loads. The main factor in transporting large loads is eco- nomics and is a balance between the cost of the transporter and the increased production from the equipment being moved. For example it could be possible to shift a 7000 tonne dragline faster than their own means of propulsion, being the "walking feet" method. However for the cost of $10 to $12,000,000.00 or more you can afford to walk the dragline and suffer the production loss. Let us concentrate on the economically realistic. BOSICH FBT MINESITE LOWLOADERS 100 TO 350 TONNE CAPACITY. Why initially consider having such a transporter? Our experience has shown that initial enquiries evolve from mines requiring to move large drills, 50 to 200 tonne weight and large hydraulic excavators or backhoes which are track mounted. The reason for shifting them is to move equipment from a mining face to enable blasting, to remove to the central workshop for repairs, overhauls and routine maintenance, to transport equip- ment from one mine face to another, and for drills, to move from one drilling pattern to the next. The cost in terms of time lost and extra wear on tracked equip- ment easily justifies the cost of the transporter. The tracks on large drills and shovels are not intended for long distance walk- ing. These tracks are designed to move the machines to position for drill holes, or moving around the mine face. Long distance travel, ie generally 1 km or more, results in overheating of track rollers, track drive components and accelerated wear on tracks.

Jan 1, 1989

The introduction of rubber tyred diesel equipment underground in the early 1960's and subsequent design improvements to diesel haulage systems over the past 2 decades has meant that diesel truck haulage has often been the first choice when selecting a haulage system for a new underground mine. Even today only 9% of all vehicles underground are electric powered.However, with the development of more efficient electric haulage systems, the suc-cessful installation of low cost shaft hoisting systems and improvements in conveyor design, alternative haulage systems are appearing as viable alternatives to diesel truck hauling. In particular, the aspects of ergonomic and environmental operating conditions, maintenance and operating costs as well as productivity rates are becoming more and more important in the selection of underground haulage systems. Future develop-ment of existing diesel haulage systems will require that diesel haulage units become more productive, have considerably reduced exhaust emissions compared to existing units and remain the cheapest haulage method for under-ground one way haul distances up to a distance of 3 kilometres. Development of electric truck and associated fuel cell haulage systems

Jan 1, 1985

By G J. Harbort, V Lawson, L Reemeyer

The Jameson Cell is a high intensity flotation device, which utilises induced air from the atmosphere. It was developed jointly by Mount Isa Mines and Professor Graeme Jameson of the University of Newcastle in the 1980s. It is proven to generate fine bubbles, in the order of 300 to 500 ¦m, in a high intensity, high shear and compact zone contained in the downcomer. This aerated mixture exits the downcomer into the pulp zone, which is the quiescent mineral and gangue separation zone. A number of Australian base metal flotation circuits feature a reverse flotation stage at the head of the circuit. Testwork and plant operating data has shown that the use of a Jameson Cell in the prefloat cleaner application has further improved prefloat gangue recovery and selectivity. Operation of a Jameson Cell in a carbonaceous/pyrite prefloat cleaner duty at the Mt Isa copper concentrator increased copper recovery and reduced pyrite in the copper concentrate. Testwork at Zinifex Century Zinc Mine showed a decrease in zinc losses by the utilisation of Jameson Cell prefloat cleaner. Appraisal of a Jameson Cell in a scalping role within the Mt Isa Copper Concentrator indicated significant benefits could be achieved.

Jan 1, 2005

By Kane, M O&apos

The mineralised members of the Brockman Iron Formation mined at Mt Whaleback are overlain and underlain by shale horizons. To maximise resource recovery, waste movement within the life of mine plan will total approximately 3.3 billion tonnes. Approximately 15 per cent of waste materials contain zones with varying amounts of sulfides and carbon and are referred to as æreactive shaleÆ. Reactive shale has the potential to self-heat and can react with some explosives, resulting in spontaneous explosion. Sulfide rich zones also have the potential to generate acid rock drainage (ARD). Successful mining of reactive shale requires constant co-ordination between the geology, mine planning, mining and environment departments. Safe storage of reactive shale is the focus of ongoing research. Since the mid-1990s, a number of trials have been undertaken at Mt Whaleback in order to further the understanding of the physical and chemical properties of reactive shale. This paper summarises some of these trials, and discusses key learnings arising from interpretation of results. Ultimately, the learnings from this research will provide the guidelines for successful storage of reactive shale.

Jan 1, 2003