Search Documents

By T Davis

The 500 orebody in the upper levels of Mt Isa Mines in north-west Queensland was mined by sublevel caving and block caving from 1962 to 1969. The hot and reactive rock mass of this orebody provided significant mining challenges including ground temperatures above those resulting from the geothermal gradient. Recently Xstrata Copper has been studying the potential to mine this orebody by modern caving techniques. Part of the study process has included re-accessing the ore zones for diamond drilling and trial development. A cross-cut trial drive, the first primary development into the orebody in more than 30 years, encountered a temperature increase in development holes from low sixties to almost 80¦C in less than 10 m advance. The issues associated with managing this risk include sourcing suitable quantities of reactive ground explosives for a single small heading and the temperature limitations of the explosives and detonators. Risk management outcomes included controls to mitigate the safety and reliability risks relating to misfires. The control that dealt directly with the challenge of continuing development in elevated temperature ground was to cool the holes before and during charging. The most effective and practical cooling medium proved to be water. Rapid rock temperature recharge time meant cooling had to continue as close to firing as possible. Reticulation systems were constructed to allow cooling to take place up until withdrawal for firing. No misfires occurred with the cooling system and additional controls in place. This proved that developing safely and effectively in the elevated ground temperatures of the 500 orebody is practicable.

Jan 1, 2008

By Tomlinson R. C

The paper will briefly describe planning in the National Coal Board (NCB) and the contribution that operational research makes to it. It will then give details of some of the models in use and will finally consider critically the problems of looking ahead to the next century.

Jan 1, 1977

Kalgoorlie Consolidated Gold Mines Pty Ltd (KCGM) is a management company, formed in 1989, to manage the assets and operate the Kalgoorlie joint venture for the owner companies Gold Mines of Kalgoorlie Limited (GMK) and Homestake Gold of Australia Limited (HGAL). Mining is still in progress on the 'Golden Mile' and surrounding areas more than 100 years after Paddy Hannan's discovery adjacent to the active Mt Charlotte mine. From 1893 until 30 June 1995 the Kalgoorlie Goldfields has produced approximately 45 million ounces (-1400 tonnes) of gold from mining and treating about 179 million tonnes of ore. This production equates to about 20 per cent of the total Australian gold production and about one per cent of the world's

Jan 1, 1996

By Cornwell P. J

The Pajingo ore bodies consist mainly of auriferous quartz veins hosted by a suite of hydrothermally altered andesitic pyroclastics, volcanics and epiclastic sediments. Scott lode, the main economic deposit in the area, lies in a zone of major structural disruption and contortion. High grade gold and silver mineralisation is selectively mined by open pit methods. Standard grade control techniques and extraction methods were adapted to minimise mining dilution and to maximise metal recovery. Basic blending of grade ranges at the crusher has produced an average 10 gram/tonne gold head grade. The estimation of ore reserves calculated by both standard polygonal and geostatistical methods proved acceptable. Mineable reserves when compared to in pit reserves defined by blast hole drilling, indicate a decrease in tonnes and an increase in the grade resulting in an acceptable comparison of the total ounces of contained gold. The ore reconciliation of mined against milled ounces indicates that both ore reserve and grade control models underestimate the metal content in the orebody. Sampling techniques are being examined in an attempt to reduce this discrepancy.

Jan 1, 1989

By Simmons SF, Fleming J

Alteration and mineralisation at the Island Copper deposit is related to the intrusion of Early Jurassic quartz feldspar porphyry dykes into surrounding comagmatic Bonanza volcanic rocks. The pyrophyllite alteration zone forms an upward flaring cone, largely hosted within a breccia body that c ross-cuts the Cu, Mo, and Au-rich ore shell. This alteration zone contains pyrophyllite, dumortierite and diaspore and resembles alteration occurring in some high-sulfidation deposits, but which is barren. Fluid mineral equilibria and fluid inclusion studies indicate formation at approximately 300 ¦C from fluids dominated by steam and gases. These fluids appear highly acidic, but sulfur poor, leading to extreme base leaching within the breccia body and surrounding rocks.

Jan 1, 1995

By Yoon R-H, Luttrell GH

A theoretical model has been developed to predict the probability of particle collection by air bubbles in a quiescent flotation pulp. The model considers the effects of both hydrodynamic and surface chemistry forces acting during the bubble-particle interaction. Hydrodynamic forces considered include the gravitational, buoyancy, streamline and film thinning resistance forces. The surface chemistry forces considered include the electrostatic, dispersion and hydrophobic forces. The hydrophobic force has been estimated from extended DLVO theory. The model is capable of predicting hydrodynamic and surface chemistry conditions under which bubble-particle adhesion is possible. Validity of the model has been verified experimentally.

Jan 1, 1993

By Sheard SN, Tucker DH

Sampling procedures are an important aspect of geophysical exploration survey design. It is good practice that the selection of survey parameters ensures that the signal to noise ratio is optimised, while minimising survey cost.Sampling considerations for any geophysical method include the size of the target, scale of observation, aliasing associated with station and line spacing, nature and extent of overburden, and the presentation of data.As a guide to survey design, the specifics are discussed for three geophysical techniques in common use in mineral exploration; these include the magnetic method, transient electromagnetics and induced polarisation.

Jan 1, 1976

By Bruce See J

Oxidation of artificial Imperial Smelting Furnace lead bullion was performed during cooling between 1180 and 820°C in order to attempt to produce a tin-rich dross.The addition of sodium carbonate together with stirring increased the tin content of the dross when oxidation was carried out with air or PbO on zinc-free bullion.Zinc in the bullion during oxidation resulted in a decrease in tin concentration of the dross due to zinc oxidation and copper entering the dross.

Jan 1, 1987

By A T. Owen, F A. Benn, J D. Swift, D M. Labbett, A F. Grabsch

The AMIRA P266 æImproving Thickener TechnologyÆ series of projects has sought to provide a firm scientific basis for feedwell and thickener design, a requirement as pressures on water usage in the minerals industry increase. While advanced computational fluid dynamics modelling of feedwell processes has generated the most obvious and successful applications to improving the performance of operating units, such outcomes have drawn heavily on parallel studies into flocculation fundamentals. Central to this has been the development of a linear pipe reactor system that allows the kinetics of flocculated aggregate growth and rupture to be measured for thickener feeds under turbulent pipe flow conditions. This ensures much greater control of the intensity and duration of applied shear than is possible with conventional flocculation test procedures, offering insights into flocculation processes that would be otherwise hidden in time-averaged measurements.

Jan 1, 2009

By Bennet A. G

As part of the construction of the Melbourne Underground Rail Loop it was necessary to construct two 7 metre diameter tunnels, each 100 metres in length, by shield driven excavation through an alluvial valley at Elizabeth Street. The tunnels had a primary support of bolted precast reinforced concrete liner blocks and were excavated with the aid of compressed air. The work was undertaken by the Tunnelling Group of the Melbourne and Metropolitan Board of Works as nominated sub-contractor to John Holland (Constructions) Pty. Ltd. The paper describes some of the problems associated with the construction of the above tunnels and the methods used to overcome them. In particular

Jan 1, 1981

Through the use of structural analysis programs such as Unwedge and considering the shear strength of applied fibrecrete it can be shown that fibrecrete can provide a higher factor of safety in a ætypicalÆ underground development excavation than standard rock bolts. This paper describes the progression of ground support from an æas requiredÆ component of mining to the use of bolts and surface support as a mandatory requirement. With the mandatory requirement for surface support, fibrecrete has been considered and applied as a secondary feature but simple analysis and practical observations indicate that it may be considered as primary support. The key elements to its implementation are: When is it safe to work under fresh fibrecrete and how do we practically determine this? How much ground support does fibrecrete provide? How can we reduce the cost of fibrecrete? An examination of these questions indicates fibrecrete can be much safer,less expensive and quicker to install than normal ground support elements. This paper explores practical examples from sites where significant benefits have been achieved by mine operators.

Jan 1, 2005

By Johnston R. F

The factors which influence the reduction of chromite are investigated with special reference to Coobina chromite. This was compared with a South African chromite ore. The reduction characteristics are outlined and the reduction kinetics studied Temperature has the most significant effect, followed by particle size, silica addition and type of coal.Electron microprobe analysis of the products indicates that iron in the chromite is first reduced at temperatures above 1100°C, followed by chromium at around 1200°C. At temperatures greater than 1200°C metallic iron and chromium are formed simultaneously and subsequently give an iron-chromium-carbon alloy. It was observed that the metallic carbide contains a small amount of silicon. The decomposition of the chromite spinel was observed to pass through the FeO.Cr2O3, MgO.Cr2O3 and MgO.AI2O3 forms before slag formation. It is concluded that Coobina chromite is suitable for the production of ferrochrome if direct prereduction followed by intensive bath smelting is used.

Jan 1, 1994

By S Smith

Several styles of copper (Cu) mineralisation are present at Sepon. Large tonnage, low grade skarn and carbonate replacement massive sulfide mineralisation occur within the metamorphic aureole of Permian-aged rhyodacite porphyry intrusions (RDPs). During exhumation and supergene weathering, this primary mineralisation has been upgraded to form high-grade chalcocite enriched zones up to 50 m thick, which comprises the bulk of Cu resources currently being mined at Sepon. Groundwaters remobilise Cu to form exotic accumulations of malachite that are locally hosted in irregular karsts in carbonate rocks, found up to 1000 m from source mineralisation. Khanong is the largest Cu deposit and recent discoveries have been made at Thengkham South, Thengkham North and Phabing. All deposits have formed by similar processes of mineralisation. However, all differ due to local variations in host rock lithology, structural setting, and hydrological conditions. An EXTENDED ABSTRACT is available for download. A full-length paper was not prepared for this presentation.

Jan 1, 2008

By D Giles

We present plate tectonic reconstructions, showing that porphyry-type ore deposits are spatially and temporally linked to ridge subduction. A reconstruction of the Peruvian subduction system reveals an immediate metallogenic response to the arrival of the Nazca Ridge at the subduction trench, followed by southward migration of the zone of metallogenic activity due to the lateral migration of the zone of ridge subduction. A similar pattern is recognised in central Chile , where the spatio-temporal distribution of giant ore deposits coincides with the arrival of the Juan Fernandez hotspot chain at the subduction zone. We conclude that there is a spatial and temporal link between ridge subduction and ore deposit formation, with high metal fluxes concentrated in zones of ridge subduction. Thus, the recognition of tectonic patterns associated with ridge subduction can provide insights into predictive mineral discovery by enhancing our ability to predict the position of large mineral deposits in other modern and ancient orogens. An EXTENDED ABSTRACT is available for download. A full-length paper was not prepared for this presentation.

Jan 1, 2008

By M Fahey, A B. Fourie

Over the past ten years, the mining industry has witnessed the introduction of a new and innovative mine filling technique known as paste fill, which consists of placing full stream tailings with small amounts of binder and water into underground stopes. Paste fill has benefits over traditional backfill methods, such as higher solids contents than hydraulic fill and easier transportation than rock fill. From a geotechnical perspective, the behaviour of very fine material in a fully saturated state can be complex, particularly when binder is added. Previously, there has been no rigorous solution to understanding the paste fill deposition process, resulting in uncertainty regarding critical aspects such as barricade load calculations. This uncertainty has the obvious consequences of potential barricade failures (including at least 12 over the past four years), and for many operations attempts to deal with this uncertainty has led to excessively conservative filling schedules, restricting production. This paper presents an application of Minefill-2D, the first rigorous model capable of representing the paste fill deposition process. The model couples the processes of material accretion, consolidation and cement hydration to calculate the distribution of stress around a stope (including the total stress applied to barricade structures) during filling. Minefill-2D is a finite element numerical program, which has been verified using laboratory element tests, centrifuge tests and in situ measurements (Helinski, 2008). The authors present a sensitivity analysis, carried out using the model, to demonstrate some of the critical and less critical aspects relating to paste backfill deposition. The results of this sensitivity analysis are used to devise a fill management strategy that can be utilised to minimise the risk of barricade failures and maximise fill rates where appropriate.

Jan 1, 2008

The comparison of belt drives with other types of power transmission involves the consideration of many factors before a final choice is made. Where other forms of power transmission might also be suitable, the selection of the correct type of belt has first to be made, in order to obtain a true comparison. The paper first deals with the types of belting available, followed by a description of most other forms of transmission equipment. An example is then given of the selection of suitable belts, which are then compared with other types of transmission. Comparative costs are also given. Reference charts provided show drives found suitable in general practice...

Jan 1, 1964

By T Lancaster

The Mount Gordon operation, consisting of the Esperanza open cut mine and the unique Mount Gordon Ferric Leach processing plant, is operated by Western Metals Copper Ltd at Mount Gordon, 125 km north east of Mt Isa. The processing plant treats predominantly the secondary copper sulphide minerals, chalcocite and covellite. The gangue consists of massive pyrite and a range of silicified siltstones. The processing plant utilises a conventional single stage SAG/cyclone milling circuit, followed by low-temperature/low-pressure autoclave oxidation to produce copper in solution. The pregnant leach solution is treated via conventional SX/EW technology to produce copper cathode. Currently the plant is operating at a nominal production rate of 48 500 tpa copper. The Mount Gordon Ferric Leach technology is the worlds first integrated pressure leach/SX/EW process to be used to treat copper sulphides on a full plant scale. In the last six months, July to December 2001, the plant has emerged from a two-year postcommissioning phase to achieve steady state operation. This has been characterised by high plant availability and consistent production performance in excess of the name plate capacity of 45 000 tonnes. Production rates will continue to increase over the next 12 months to over 50 000 tpa via a planned process of incremental improvements. The pressure leach circuit has consistently achieved availabilities exceeding 95 per cent over the past 18 months. Notwithstanding this, the leach circuit still has a much greater requirement for planned maintenance than SX/EW. For much of the Mount Gordon processing plantÆs operating life, the leaching process has constrained production. Recent developments arising from detailed mass and energy balance modelling have now significantly improved leach capability, resulting in the plant bottleneck being shifted to electrowinning. In order to balance the capabilities of the two circuits however, the surge capacity between leach and SX/EW was increased substantially. This effectively de-coupled the higher capability but lower availability leach circuit from the lower capability but higher availability SX/EW circuit. As a result, electrowinning utilisation has increased to in excess of 98 per cent, which is reflected in a higher overall plant throughput.

Jan 1, 2002

By Gadsden R. W

Physical and chemical requirements are defined for coke and ferrous materials used in modern high productivity blast furnaces operating in Australian conditions. Recent developments in the type of equipment required to be installed at the steelworks to ensure these requirements are described with illustrations from current plant practice provided.

Jan 1, 1976

Precipitation of inorganic compounds or metals from aqueous solutions can either be physical (crystallisation) or chemical in nature. Chemical processes are varied; they may be due to hydrolytic action, due to ionic interaction, or due to reduction (ie transfer of electrons). Transfer of electrons in reduction processes may take place homogeneously or heterogeneously. In the first case it may be ionic or nonionic in nature. Heterogeneous processes may be electrochemical or electrolytic. Examples of interest to hydrometallurgy are given.

Jan 1, 1993

The foundation of our industrial welfare lies in the success of our primary industries, and, so far as mining is concerned, it is hoped that for many years it will be a most important primary industry in Western Australia.

Jan 1, 1927