Search Documents

By M Binks

This paper presents a case study that describes the selection, development, engineering and construction of a process plant for the biological oxidative pre-treatment of a refractory pyrite-arsenopyrite gold ore flotation concentrate. Prefeasibility and feasibility study resource modeling, metallurgical testwork, and environmental and engineering studies are outlined. Options considered for oxidation of the ore, which examine cost, risk, operability, recovery, engineering and environmental aspects are compared, with particular reference to pressure and biological oxidation. The BIOX« biological oxidation process was selected as the preferred oxidation process and the flow sheet for this process is presented. Selection of the BOIX« process resulted in special requirements for the feed preparation circuit, residue treatment and disposal, materials of construction and engineering. Use of a biological process in ore treatment also introduces particular process and engineering risks the management of which are discussed.

Jan 1, 2004

By Adranyl W. W

Sub-level caving with bottom ore drawing has gained wide acceptance in rich, soft, low magnetic iron ores because it provides moderate ore dilution and ore losses. The main problem here is the high rock pressure exerted on sub-level drives situated in the sub-level sill pillars. To reduce this effect, the ore block is divided into panels. This paper illustraes the method of determining the maximum panel width providing low maintenance cost of sub-level drives.

Jan 1, 1995

It is a well known fact that the best method of rock reinforcement is to avoid physical ground support. This goal can be achieved by means of: - Increasing the rock structural strength - Geological definition and forecasting. - Sequencing the excavation - Smooth blasting In many cases however, extra ground support is needed in order to maintain safe working conditions. In an open pit, the structural strength of rock cannot be increased by lowering the pit walls due to economical reasons. Economy demands steeper walls and less waste to be hauled to the dump. The geological conditions can also often be extremely poor and unpredictable. For excavation sequencing and smooth blasting there are good possi- bilities, such as cleaning of the pit walls after the main excavation, arul- ing of long small diameter straight inclined holes, use of smooth blasting techniques and lightened explosives.

Jan 1, 1989

By Lang SC

The Broken River Province, in the northern part of the Tasman Orogen, is divided into the Camel Creek and Graveyard Creek Subprovinces. In the Late Cambrian to Early Ordovician, and again in the Late Ordovician, the northern part of the Tasman Orogen was probably a convergent margin with calc-alkaline volcanism. These episodes may have been separated by a passive phase in which quartz-rich flysch and tholeiitic volcanic rocks were deposited. Subsequently, in the Silurian, the region underwent extension forming a large turbidite basin which included the Camel Creek Subprovince and the Hodgkinson Province to the north. Melange is pervasive in the Camel Creek Subprovince which was folded twice in the Devonian. The melange may be related to thrusting accompanying D1. No rocks younger than Early Devonian have been recognised whereas, in the Hodgkinson Province, deposition continued until the latest Devonian. The Graveyard Creek Subprovince formed adjacent to the Camel Creek Subprovince, probably as a pull-apart basin on stable crust. The deformation history of the Graveyard Creek Subprovince contrasts markedly with that of both the Hodgkinson Province and Camel Creek Subprovince. In the Graveyard Creek Subprovince, melange is only present in Early Ordovician rocks. No major angular unconformities have been recognised in the overlying marine to non-marine sequence, which ranges from Early Silurian to Early Carboniferous. Several hiatuses and a slight angular unconformity, all within the Devonian, may be related to the major events in the Camel Creek Subprovince. A major deformation in the Graveyard Creek Subprovince in the Early Carboniferous had only slight effects in the Camel Creek Subprovince. Movement on the Clarke River Fault was probably an important influence on sedimentation and deformation in the Broken River Province.

Jan 1, 1990

By B Washington, A Campbell, R Taylor

A sampling and measurement program was undertaken on the reaction shaft of the Olympic Dam copper flash smelting furnace. The object of the work was to provide information to validate a mathematical model of the burner and reaction shaft. Samples and measurements were undertaken through the burner inspection ports and the South East (SE) shaft sampling port about half way down the reaction shaft. Samples were collected to enable the calculation of particle loading of shaft gases, or sizing and chemical analysis of the partly-combusted feed, and the preparation of polished sections. Measurements were made of the temperature and sulfur dioxide content of the atmosphere, as well as plume velocity.To implement the program it was necessary to design and construct the following specialised items of equipment. For use at the burner inspection ports: a cup sampler for obtaining samples below the burners (temperature, solids loading and samples for characterisation).For use at the SE shaft sampling port and also at the settler level: trough sampler (plume definition and samples), isokinetic sampler (used as a velocity probe in this work), temperature probe (temperature traverses across the shaft), and sulfur dioxide probe (SO2 measurements across the shaft).The design of the sampling and measuring equipment is described, and examples are cited of the types of information obtained. The problems arising from working in a hot environment with molten or sticky particles are discussed.

Jan 1, 2005

The mined-out Old Waite volcanogenic Cu-Zn deposit lies in the Noranda mining district of northwestern Quebec. The deposit has a distinctive pipe-like zone of alteration beneath the massive ore, extending into the stratigraphic footwall. The hydrothermal metasomatism within the alteration pipe produced a concentric zonation. with a peripheral quartz - sericite - chlorite mineral assemblage surrounding an axial core of magnesian chlorite - Phlogopite.

Jan 1, 1989

By J H. Baker, P G. Beadle, J P. O&apos, Brien

In 1974 a preliminary study of the refractories industry in theRepublic of Indonesia was completed by Crown Lynn Consultants, a subsidiary of Cerarnco Ltd., on behalf of the Indonesian and New Zealand Governments. As a result of recommendations arising from that study the two Governments commissioned, in 1976, as a Bilateral Assistance project, an investigation into the potential of the refractories industry in Indonesia. Ceramco Ltd., was retained to carry out the study on behalf of the New Zealand Government. The Directorate-General of Chemical Industries, Directorate of Silicate Industries administered the project on behalf of the Indonesian Government. Indonesian counterparts to the New Zealand study team were provided by the Directorate of Silicate Industries.

Jan 1, 1978

By Buizen M

The results of calibration trials conducted on parachute stoppings under a recently completed NERD&DC grant are presented. Applications of parachute stoppings, for rapid regulation and control of ventilation networks are described including use in mine recoveries, sealing sections and rescue work. Parachute stoppings are one of a series of non-rigid ventilation control structures specifically designed for quick installation in emergency situations, for use in high production/rapid advance areas and areas suffering roof-floor convergence.

Jan 1, 1988

By Carlson BL, Overton DD

This paper compares the designs of heap leach facilities for four precious metal mining projects in the southwestern United States. These four proposed projects are of small-to medium-size relative to other operating mines in the United States, and are either permitted or in the final stages of permitting. The differences and similarities in the heap leach facility designs are compared with respect to site conditions, operating conditions and regulatory requirements. This comparison provides a summary of the state-of-practice for heap leach facility design in the southwestern United States and identifies current issues in project development and process material containment.

Jan 1, 1997

The city of Kalgoorlie-Boulder is located 595 kilometres east of Perth in Western Australia, and has a population of just over 30 000. Western Australia's third largest city lies on one of the richest goldfields in the world, with over 45 million ounce

Jan 1, 1998

This paper addresses the area of utilising automatic data capture systems in the metalliferous mining environment for the purpose of tracking personnel and vehicles, for both safety and productivity purposes.As automatic data capture systems in the form of barcodes have revolutionised the stock control procedures in retail establishments in recent years, so too will similar systems in the form of radio frequency identification products (an electronic version of the barcode) transform the way in which many aspects of mining operations will be managed.

Jan 1, 1992

By S F. Simmons, A McOnie, J L. Mauk

Three cross sections, 200 m apart, display the distribution of indicator hydrothermal minerals across the Empire zone of the Golden Cross epithermal Au-Ag deposit, Waihi, New Zealand. These minerals are used to interpret the temperature and composition of hydrothermal fluids. The distribution of interstratified illite-montmorillonite and illite indicate that temperatures ranged from 140 to >220¦C, with temperatures above 220¦C predominating. The mineral assemblage of quartz-adularia-chlorite-illite-calcite-pyrite envelops the Empire vein system and stockwork, and reflects formation from an alkali chloride water whereas the mineral assemblage of replacement calcite-interstratified illite û montmorillonite-kaolinite forms a carapace and reflects formation from a CO2-rich steam-heated water. Alkali chloride waters appear responsible for the epithermal Au-Ag mineralisation.

Jan 1, 1995

By Ritchie IC

Spiral separators have been used to treat heavy mineral sands in Australia for some thirty-five years. They were used as the primary treatment method until the advent of the Reichert cone, which largely replaced them, due to its compact design and relative ease of operation. Spirals continued-to be used as the final cleaning stage before dry separation of the heavy minerals as they remained the most efficient separator for this purpose.

Jan 1, 1986

The Australian Mineral Industries Research Association, set up by the mineral industry in 1959, acts as a research and development broker and manager for the industry. In 1984/85 it contracted out just over $3 million of projects. Its structure and method of operation is described and highlights of some of the successful projects are given. The complex process of developing new proposals is described. This involves the establishment of effective communication networks within the industry and between the industry and research personnel working outside it. The advantages of the industry tackling some of its problems on a jointly sponsored basis are listed. Possible avenues for future development by the Association are given.

Jan 1, 1986

Diversification has characterised the mining industry in this country and globally in recent decades, and in Western Australia in particular. One of the most obvious aspects of diversification is technological change which continues at a rapid and sometimes bewildering pace. A function of technological advances is the increased capacity to further diversify the range of minerals which can be identified in economic concentrations and profitably extracted. This broadening of the total base of the industry has a synergistic effect on its further development by extending its geographical spread and increasing scope for decentralised infrastructure. Another aspect of diversification is the corporate thrust towards establishing overseas mining bases for a variety of reasons. Off-shore (sea bed) mining is a further manifestation of increasing diversity, although very much in its infancy.

Jan 1, 1996

By Thompson D, Burgess G. C

Subsequent to large scale trials in 1987, the installation of a submerged lance Sirosmelt furnace system was approved in late-1988 for the cupellation of retort bullion to dore silver. Commissioning work commenced in June 1990. During the process air is lanced into a molten slag bath contained in a cylindrical vessel to rapidly oxidise the granulated feed bullion from 15 - 25 per cent silver to rough dore grade. The process is now an integral part of the Precious Metals operation replacing the first stage reverberatory cupellation furnaces to achieve productivity improvements, lower silver inventory and increased silver Recovery.

Jan 1, 1992

In presenting size analysis data, one has the choice of various graphical techniques; each no doubt has been developed to highlight a particular aspect of the data. A frequency size distribution plot is used quite extensively to illustrate the importance of the finer size particles in iron ore granulation. However, the basis for such a plot is often not appreciated. As a result, cases of incorrect use can be cited. The aim of this paper is to extend the work of Alien (1981) and to provide, using examples and figures, a basic understanding of the implications of the various size distributions. A simplified method of presenting sizing data on a linear scale graph paper is presented and recommended. This involves a simple construction of a histogram of mass fraction versus particle size (in geometric progression).

Jan 1, 1992

By Worotnicki G, Tillmann V. H

Past experience with fully bonded cable dowels placed as a means of reinforcement in highly stressed crop pillars at the New Broken Hill Consolidated Limited (NBHC) mine indicated such support was not fully effective. Typically overbreak of the crown occurred leaving long lengths of cables hanging from the back stripped of grout and rock with the potential load carrying capacity of the cables not having been fully utilised. This mode of behaviour had been observed in the cable dowelled crowns of three longhole open stopes (EROS) mined to the No. 12 level at NBHC. A system of support with improved mechanism of load transfer from rock to cable and capable of full utilisation of cable strength was proposed for the crown pillars of future Stopes.

Jan 1, 1983

The Quioma Mine is located along the axis of the Cordillera Oriental, 130 km southeast of Cochabamba, South Central Bolivia. Silver, lead, zinc, antimony, and gold have been intermittently produced from veins in the Quioma area since Colonial times. Mineralization occurs within steeply dipping fissure veins transecting moderately folded Lower Ordovician sediments. Tectonic activity is early to mid-Tertiary and the vein system parallels the fold axis of a major northwest-southeast striking, doubly plunging anticline. Vein sets occur within a 2 km wide band over a strike distance of 13 km along the northeast limb of the anticline. Economic mineralization occupies syntectonic pre-mineral fault zones developed in more competent stratigraphis units of Lower Ordovician clastic sediments. Veins average 55 cm in width, although mineralized structures up to 3 m wide with a known strike length of several hundred meters have been mined. Mineralization consists of siderite, argentifferous galena, sphalerite, and quartz, with minor amounts of chalcopyrite, barite, and bournonite. Pyrite is rare except at the Boston vein where it occurs with stibnite that contains trace amounts of gold. A marked characteristic of veins in the district is evidence of repeated stages of movement during mineralization. Intrusive rocks are rare in the Quioma area. Narrow porphyritic dikes of Andesitic composition averaging 1 m in thickness have been observed. These dikes occasionally show a close spatial relationship to the veins and are often kaolinized and carbonitized. Vein and dike contacts are sharp and alteration does not appear to extend into the wall rock. Mineral zoning is suggested by antimony mineralization observed in peripheral areas of the anticline.

Jan 1, 1987

By Pease JD

This paper reviews the changes in operating practices made in the heavy medium plant to meet the objectives of increased silver, lead and zinc production at lower operating cost. The effects of medium quality, screen- ing efficiency, medium consumption, equipment service life and plant availability on these objectives are described.

Jan 1, 1988