Search Documents

Published information on technical and market developments in the uses of zinc tends to dwell very largely on two groups of uses of zinc - zinc coatings (mainly galvanising) and zinc casting alloys. These two groups account for two-thirds of primary zinc consumption. However, if total zinc consumption is taken into consideration, coatings and casting account for a little over half the total. Either way, the health - or otherwise - of these 'other' uses of zinc can have a substantial effect on the industry as a whole. The aim of this paper is to put the whole market picture for zinc into better focus, concentrating on the factors which can affect consumption in the 'other half' of zinc's markets: ò brass - the third most important market for zinc at around one million tonnes - responds to changes in the economic cycle. It has seen substantial changes in the balance between different forms of semi products, and, in Europe at least, some real market gains; ò zinc sheet - one of the original uses of zinc in Europe - has grown substantially in some countries, but remains almost unknown elsewhere; and ò zinc pigments and compounds are so numerous that - barring the substitution of zinc oxide in rubber - major overall changes in the market are unlikely. The paper examines these markets and assesses their potential and implications for zinc markets as a whole.

Jan 1, 1993

Mond gas-producer tar, and, in fact, all tars obtained from the retorting of coal where steam and air are admitted to the retort, are of entirely different chemical composition to the ordinary coal tar made in the gas or coke works. These tars contain none of, the aromatic hydrocarbons - benzene, toluene, naphthalene, and anthracene, sought after by the ordinary coal-tar refiner.The distillation of Mond tar shows it to consist of phenols of high molecular weight, unsaturated hydrocarbons of high gravity and low viscosity, paraffin wax, and resinous substances of whose composition little is known.The physical properties of Mond producer tar are also peculiar. It has a "short," granular texture when cold, which might be likened to candied honey. It "dries" (hardens) when exposed in thin layers to the air, and, for a coal tar, it cannot be considered sticky. This latterò property, combined with the short texture, prevents its being used successfully for road-making or macadamizing.The drying properties and the paraffin wax contained in: this tar cause it to hold up large percentages of water, probably in the form of emulsion. When containing as much as 10% to 15% moisture it appears to be quite dry.

Jan 1, 1918

By Barclay C, Jacobsen M, Towsey C

The Emperor Gold mine at Vatukoula, Fiji, is a nine million ounce gold telluride deposit. In January 1992, the mine was on the verge of closure when the current management team took charge. Losses had been incurred for two consecutive years and the published resource amounted to less than five years of production. Relationships with the workforce, the government and the general public were poor. Today, the mine has recorded three consecutive years of profit, has resources that will support the operation for at least 20 years and has excellent relationships with employees, government and the general public.

Jan 1, 1997

The Engineering Chemistry Division of the Government Chemical Laboratories of WA initiated an ongoing investigation into the possible utilisation of diatomites of this State. The work has shown that local diatomites can be beneficiated by hydro or pneumatic cyc- lone separator circuitry and that the better quality head materials can be upgraded by straight and flux calcination and associated processing to the equivalent of premium grade imported products. Western Australian diatomites vary con- siderably in quality, and the degree to which they can be upgraded and the yield of useful product are influenced by the proportion of impurities and the size, type, and degree of fragmentation of contained diatoms. Conseq- uently careful assessment of ore deposits will be necessary in order to relate ore reserves to planned production. The viability of commercial production from Western Australian resources would hinge on the establishment of markets - largely ex- port - capable of supporting a production level of the order of 30,000 tonnes per annum.

Jan 1, 1979

By Weller KR

Computer programs are described which help the metallurgist to process sample data from a plant survey; to carry out simple mass balance calculations; to present the results of circuit and equipment performance in convenient form; and to simulate the circuit response to changing operating conditions. The uses and limitations of these programs are explained by following through a case study of the sulphide flotation circuit at Cleveland Tin Ltd. The circuit was sampled, the data analysed, and some process inefficiencies established. Simulation calculations were then made to provide information on which to base decisions regarding possible circuit changes aimed at improving performance.

Jan 1, 1983

By D Elder, S Bell

Over the last five years Solid Energy New Zealand (SENZ) has gone through a series of changes in response to both external and internal factors. These changes have included corporate reorganisation and funding restructure, as well as modifications to medium and long term business objectives. The nature and size of its coal reserves and markets requires SENZ to continue developing new mines as existing mines are depleted. As well, there are opportunities to develop new mines as coal markets change or to realise value from existing coal resources. To assist in this process, a set of mine project assessment guidelines which are relevant to the size and scale of anticipated mine developments have been developed for SENZ. These project guidelines are structured to operate from the early stages of project or resource review through to final feasibility study stage. The guidelines provide both a basis for planning and budgeting, and a control mechanism within the company. They also enable clear understanding of the status of individual projects and provide a framework for comparison between projects. SENZ now has a defined method to plan, monitor and control this important aspect of its business. The paper explains the development and structure of the guidelines, as well as providing examples of their application. and use. It demonstrates how SENZ integrates its long term planning, five year planning, annual planning, project planning and risk management to maximise the value of individual projects, business units and the company overall in a consistent manner.

Jan 1, 2002

By M Noy, P Hawkes

Improvements in the drill and blast process can impact on loader performance in a number of ways. The main effects being improved loading cycle times, less non-productive cycles such as oversize removal, clean-up and face raking and better bucket fill factors. The impact of improved loading cycle times on the overall cost and productivity of the load and haul cycle is very much dependent on the loader truck match and the management of the haul fleet. Previous work has shown that a 20 per cent improvement in dig cycle times may only lead to three per cent or less improvement in the overall productivity of the load and haul process. However, improving the mass loaded per pass by five per cent will lead to a five per cent improvement in productivity for any given haul fleet situation, assuming sufficient truck capacity. Work by Orica Explosives at Lab ChrysotileÆs Thetford Mine, Quebec, Canada showed a relationship between muckpile fragmentation and truck payload. With this in mind, work was carried out to determine the effect differing muckpile fragmentation distributions can have on excavator bucket fill factors. This work was performed in the laboratory to a 1:100 scale. Nine different distributions were used. These were characterised by the Rosin Rammler parameters, xc the characteristic size, and n, the uniformity index. The values of xc and n used were modelled on those previously measured at a Sydney quarry. For the range of distributions measured, it was found that the fill factors were lowest at a low characteristic size and a high uniformity index and highest at a high characteristic size and a low uniformity index. In other words the best fill factors were achieved with a more dispersed muckpile distribution with a larger characteristic size. The difference in fill factors was 16 per cent indicating that controlling the drill and blast process to produce a specific muckpile distribution can have a significant impact on the overall cost-efficiency and productivity of the load and haul process. Field measurement by Orica Explosives at a quarry in Canada supports this conclusion showing improvements of up to seven per cent in average bucket load by either increasing the characteristic size or decreasing the uniformity index of the muckpile.

Jan 1, 1999

The preconcentration of uranium ore by radiometric ore sorting at Mary Kathleen Uranium Ltd. is described. The operation of the ore sorting machines is discussed in detail and performance results obtained with the existing system are presented.

Jan 1, 1978

By Nye P. B, Fisher N. H

At the second Empire Mining and Metallurgical Congress held in 1927, the Empire Council of Mining and Metallurgical Institutions was formed and it was proposed that the Council take steps to prepare a "Review of the Mineral Resources and Industries of the Empire." At the third congress in 1930, it was resolved that the proposal to institute the review should be submitted to the Imperial Conference held in 1930. This was done, and the Minerals Committee, of the Imperial Economic Committee compiled, an interimreport which was based on statistics of imports and exports, and did not consider resources and consumption.In 1942 the Institution of Mining and Metallurgy, London, wrote to the Empire Council and stated that it was desirable that the Council should be in a position to take part in decisions affecting the future of the mining and metallurgical industries. The Council communicated with the constituent Institutions regarding the nominations of two members then in England. Subsequently the Mining, Geological and Metallurgical ,Institute of India prepared a review of the mineral resources and industries of India and their post-war development, and the Empire Council forwarded a copy to the Australasian Institute of Mining and Metallurgy and asked if that Institute would submit a review on simjIar lines for Australia. The Australasian Institute arranged that the Australian review should be prepared by...

Jan 1, 1946

By Smart RST C, Johnson NW, Ralston J, Griffin LF

At the Copper Concentrator of Mount Isa Mines, the largest diluent of the copper concentrate is liberated fine pyrite. Laboratory flotation tests carried out as a function of grind and flotation Eh in combination with surface analysis by X-ray photoelectron spectroscopy (XPS) have identified the major mechanisms of iron sulphide flotation. It was found that a significant proportion of the iron sulphide minerals had surface coverages of graphitic carbon, sufficient to impart moderate hydrophobicity in the absence of collector. A smaller, but economically significant proportion of chalcopyrite was also affected by the graphitic carbon coating. Two methods were tested to reduce the impact of the natural floatability of the iron sulphides on concentrate grades. 1. Depression through the use of organic depressants. 2. Preflotation to remove the "naturally hydrophobic" iron sulphides (flotation independant of Eh ) prior to chalcopyrite flotation. Preflotation was tested at the pilot plant scale. It was found that the amount of chalcopyrite reporting to the preflotation rougher concentrate could be minimised through flotation at a mildly reducing Eh by the use of nitrogen as the flotation gas to maintain the low Eh conditions resulting from grinding. The preflotation rougher concentrate was upgraded to an iron sulphide concentrate or a low grade copper concentrate.

Jan 1, 1991

By Jia X

Three-dimensional microscopic modelling techniques involving specific calculations based on direct computation of the Brownian, van der Waals, Born, electrical double layer repulsion, bulk, hydrodynamic and external forces (gravity, magnetic etc) acting on and between each particle in a mineral dispersion are now feasible using advanced computer processor architectures. This contribution surveys the hardware requirements, the advantages and limitations of the approach for enabling prediction of dispersion behaviour a priori. The notion of developing a generic particle simulator, akin to the use of molecular modelling in the area of drug design, based on inputting process-relevant data (solution chemistry, mineral solids properties, hydrodynamics etc) is discussed. The methodology is illustrated with application examples involving: predictions of coagulation of mineral fines; shape and size of magnetically-flocculated hematite; and the kinetics of fouling of membrane surfaces and walls.

Jan 1, 1993

Optimisation of capital in the development process is critical to the profitability of any new mining venture. The process of optimisation should apply to all aspects, that is the financing, management, revenue, reporting and, of course, the development of the project. Unfortunately, too much emphasis has been placed on the optimisation of the financing or reporting aspects and too little on the project itself. This paper addresses the latter.

Jan 1, 1991

By Goto T, Sato K, Mori N

A field investigation by making use of the seismic method has been carried out in order to comprehend the mechanism of rockburst and gas outburst and their predictive measures. The seismometers were so arranged both on the surface and underground as to enclose a mining panel. Seismic signals detected by the array were recorded and processed by the 32-kwords computer system. At present the system is available for analysing the source location and Richter's scale of each event and for visualizing the distribution of seismic foci and released energy at any mining stage. The magnitude distribution of events can be regarded as a comparable index of the seismic activities among mining panels. An analysis of the spatial density distribution of seismic energy in the mining panel can be useful to distinguish a highly stressed zone from stress released areas. The energy released curve or the rate of energy release determined from seismic data is also a good indication of the seismicity.

Jan 1, 1980

Recent developments in engine, transmission and control technology, likely to give rise to improved performance and efficiency of underground mobile equipment, are reviewed. Turbocharging and the electronic control of fuel pumps and injectors can improve diesel engine performance whilst minimizing exhaust emissions. Ceramic materials promise further improvements in engine efficiency. Nevertheless, electrically powered machines, equipped with trailing cables or 'travelling plugs' are expected to find increasing application where there is less need for flexibility and where the cost of ventilation and heating or cooling makes diesel engines unattractive. Voltage to frequency converters and induction motors appear to have a future in mains powered machines. Vehicles employing energy storage in the form of batteries or flywheels will find increasing application, but it is expected that they will remain a minority until there is a significant break-through in battery technology. Hydrostatic transmissions having high power density and efficiency are likely to be used more widely. Electronic control systems are likely to be used to simplify jobs and to improve performance and productivity. Enhancement of remote control systems is to be expected for work in unsafe areas, but true robot operation is considered unlikely for the moment. Attention to ergonomic factors should produce significant productivity gains.

Jan 1, 1985

By T J. Scanlon

Heavy minerals recovered from recently discovered deposits in the Murray Basin are proving to be somewhat more difficult to process into saleable ilmenite products than ilmenites from existing operations. This is due to the nature of the gangue minerals present, the impurities in the valuable minerals and the size distribution of the mineral assemblages. Ilmenite product quality, in particular, can be adversely affected by any of these factors. Over the past two years the authors have been involved in assessing the potential to manufacture ilmenite products from a variety of mineral sand deposits in the Murray Basin. The steps undertaken to define the potential products and develop suitable flowsheets have evolved in parallel to the exploration efforts, in cooperation with companies undertaking exploration in the Murray Basin. A combination of an understanding of detailed mineralogy, application of magnetic fractionation and modification of magnetic susceptibility of the ilmenites has in all cases, been successful in improving ilmenite product quality. The targeting of particular ilmenites to specific downstream processes for TiO2 pigment manufacture is the most challenging aspect of this development.

Jan 1, 2001

This paper reviews the geochemistry of weathered nickeliferous sulphidic and lateritic profiles, the supergene behaviour of nickel and ore-associated elements, and their implications for exploration in an attempt to distinguish between barren and mineralised nickeliferous profiles. Nickel is an abundant accessory element in ultramafic rocks with background concentrations in some units up to 0.25 weight per cent. Ore-grades in fresh rock are mostly associated with massive and disseminated sulphide zones within magnesium-rich layered ultramafic sequences. In lateritic weathered terrain, nickel is also concentrated in the regolith profile. This process not only upgrades nickel in the gossanous weathered product of sulphidic deposits, but for sub-economic sulphide zones and some ultramafic rocks, is sufficient to result in a supergene resource. Ore-grade accumulations of nickel in regolith after sulphide-poor ultramafic rocks are referred to as lateritic deposits. Nickel sulphide zones and their ferruginous weathering products are collectively referred to as sulphidic deposits and are the major source of nickel in Western Australia. Mineral exploration in the Yilgam Block is hampered by deep lateritic weathered profiles (eg Butt and Sheppy, 1975; Smith, 1977; 1982). During the nickel boom of 1967 - 1972, most discoveries resulted from the location of outcropping nickeliferous gossan and ironstone. Exposed ultramafic terrain with nickel sulphide potential were explored intensively, mostly by gossan and soil sampling. However, up to 85 per cent of the area of the Yilgarn Block is buried by transported regolith. In these covered areas, barren and mineralised rock responses at the surface are similar and soil sampling produced unreliable results due to many false anomalies. A statistical, multi-element approach to regional geochemical exploration has evolved. Potential trace element indicators investigated, include Co, Cr, Cu, Ir, Mn, Pb, Pd, Pt, Sc, Se, and Zn. In recent years, trace element ratios have also been tested with varying degrees of Success.

Jan 1, 1996

By Qisu W

The ground vibration produced by the bench blasts of a single hole and a row of two or three holes is recorded in an iron mine. Using the seismic signal generated by a single-hole shot as the source function, we have developed a computer program of a simulating ground vibration by bench blast. The reasonable delay time of blast in the iron mine has been discussed tentatively with the Fourmap invented by Anderson, D.A. The seismograms measured from the single-row blasts of two or three holes have shown the method of simulating vibration is feasible on the whole. For large scale production blasts, a combination of the vibration simulation and the high-speed photograph is used to choose the delay Time.

Jan 1, 1990

By Peirong C, Pei N, Shouxi H, Hongzhong X

Indosinian (T) orogeny amalgamated the Mongolia-Xingan fold zone, the North China continent, the Yangtzi platform and the SE China fold zone into a unified continent. The early to middle Yanshanian (J-K,) orogeny created a Cordilleran type active continental margin in East Asia, reactivated the consolidated East China continent, and generated a large amount of granitoids, calc-alkaline volcanics and W, Sn, Mo, Cu, Au, and U ore deposits. The late Yanshanian (K2) orogeny began a transition to the western Pacific type continental margin. A tensional environment led to the development of peralkaline magmatism and the formation of continental basins with red beds. The Himalayan (Tr-Q) orogeny was characterised by a backarc spreading and rifting regime. The dominant magmatism was continental basaltic.

Jan 1, 1995

By Riley S

Many regulatory bodies have, or are considering, guidelines that require rehabilitated mine spoils to be erosionally stable (satisfying quantitative limits) over specified design lifetimes. One of the problems facing the industry is that many of the computer models used for erosion assessment were developed for agricultural applications and are unable to predict the change in the shape of engineered landforms over extended periods of time. In particular, they cannot predict where valleys and gullies will develop in the landforms and how big or deep they will be. Furthermore, many existing models require considerable skill to use. A computer model (SIBERIA) developed by the first author, able to model this valley and gully development over long design lifetimes, and which is directly based on digital terrain maps is discussed here. Proposed rehabilitation strategies for waste rock dumps at Ranger Uranium Mine as assessed with SIBERIA are discussed. New features of SIBERIA of interest to the mining industry include the spatial distribution of erosion, deposition and gully development, and various measures of the quantitative risk of failure. A collaborative project with the Queensland Coal Association, involving the first author, aims to deliver these capabilities to the coal industry in a user-friendly package. The objective is the cost-effective rehabilitation of strip mines. Some preliminary results from this project are presented.

Jan 1, 1994

By Senanayake G

A sample of crude copper powder produced by the CLEAR Process was refined by dissolution and recovery in sulfate media using the Parker Process. The Parker Process offers an alternative method of copper recovery to electrorefining and allows a range of Eh and pH conditions to be used to provide further discrimination of impurities. High purity copper powder was recovered by the Parker Process even in the presence of added impurities when the Eh and pH was maintained near constant throughout the refining step.

Jan 1, 1984