Search Documents

By Reid T. W

This paper describes the results of investigations into the relationship between specific gravity and chemical composition in the Cockatoo Island orebody, In the early investigations the samples were classified into groups according to porosity. This resulted in high, medium and low porosity groups, the latter being further subdivided into ore and waste. Whole number tonnage factors were assigned to each group. In the later investigations the reciprocals of bulk specific gravity and true specific gravity were ex- pressed as linear combinations of iron, silica and alumina using stepwise regression. The efficiency of the models as predictors was tested by dividing the data into two sets; one of which was used to calculate the regression equation and the other to test the efficiency of the equation as

Jan 1, 1976

By M Castle, D Mendelawitz

The Marra Mamba iron ore in FortescueÆs Chichester Range project area occurs as a very flat dipping series of waste shale and iron ore beddings. These beddings vary from millimetre thickness to several metres. The ore material generally exhibits a moderate degree of competence when subjected to ultimate compressive strength (UCS) tests, normally failing at up to 60 Mpa. However, the strength of the beddings is markedly less when subjected to the tensile forces imposed by the cutting action of the surface miner. Two surface miners of differing age and sizes were tested over a period of almost three months. These machines produced a product that had not been subjected to dilution by blasting and of such a size that primary crushing is not required. The machines were able to cut all ferrous material presented to them with varying degrees of success. Material containing higher quantities of manganese were broken but caused catastrophic wearing of the picks. During the trial the volume of material produced by the two machines in various strength materials very closely matched the manufacturerÆs estimates. The major impact on costs per tonne related to the wear on bits, which in turn varied with the bit design and composition. Bit design and composition testing is continuing.

Jan 1, 2007

The amount of land subjected to coal surface mining in the United States has been reported at 1, 302, 000 acres (1). Latest National Coal Association estimates (1968) show that about 65, 000 acres are affected annually in the production of 186, 000, 000 tons of coal. Peabody Coal Company affects approximately 9500 acres annually in the ten States in which we are presently operating. Surface mining at Moura, Australia was begun in February 1961. In Marcy 1963, the Marion 7900 dragline with 35 cubic yard bucket went into operation and in 1967 the Marion 8900 dragline with a bucket capacity of 130 cubic yards was put into operation. In addition a third dragline, a 480W was added in 1969. It carries a 15 cubic yard bucket and is used to work areas that are too small to justify movement of the larger machines, In 1969 the Moura surface mine produced 3, 002, 774 short tons, and in 1970 3, 418, 933 short tons.

Jan 1, 1971

A series of physical tests have been conducted to determine the actual performance of bunton to shaft side wall connections typically used in new shaft construction in South Africa. The test set-up is described, together with the applied loading, which incorporates a cyclical load component and a quasi-static load component, in an attempt to simulate actual conditions in the shaft. The test results are given and it is shown that generally the performance is adequate, provided double-slotted holes are not used. Generally the fatigue performance is found to be good, with the only exception being cases where the bottom of the bunton is lower than the seating level for the bunton to side wall connection. Arising from the tests, typical design values of connection stiffness, strength and fatigue life are proposed and a design procedure including these three key aspects of connections is described.

Jan 1, 2005

By S Z. Petho

The South Deep surface shaft system is being sunk to a final depth of 2750 m below surface and on completion will be the deepest single drop shaft in the world. The shafts will intersect the target reef horizon at 2650 m below surface. In order to negate the requirement for a shaft pillar, which would be extremely large at this depth, the reef horizon in the vicinity of the intersection is currently being mined. A high quality crushed waste/classified tailings backfill is being placed in the longwall stoping panels around the shaft intersection area. This will limit closure and ride which following shaft reef intersection could have a detrimental effect on the long term shaft stability. This paper discusses underground instrumentation results and numerical modelling exercises carried out to confirm that the shaft system will be stable throughout the life of the mine. Instrumentation projects include closure and ride measured between backfill paddocks and haulage leveling exercises carried out to determine the far field rockmass response to mining with stiff backfill. Results from the numerical modelling exercises show good correlation with measured data. This indicates that a high degree of confidence can be placed in the model input parameters and consequently in the design of the shafts to ensure their long-term stability.

Jan 1, 1998

Timestudy analysis of mining operations at North Broken Hill Limited has been carried out by dissecting operations into small elemental components, and accurately timing these elements. Over a wide range of observations, this has enabled standard time values to be calculated for all underground work.The application of the standard values is in calculating performances as a measure of work output and Performance Controls are kept on approximately two-thirds of underground employees. Through the Controls it has been possible to stimulate supervisory action to improve low performance, and to reduce delays and lost time.The values are used to calculate contract" prices, and anomalies in previous prices have been adjusted on work values and not on arbitrary standards. In out-of-the-ordinary circumstances, the request for a timestudy investigation has been made by both operatives and foremen, and the contract set following the timestudy analysis has been to the satisfaction of both parties.The range of values enables contracts to be applied to work which was previously performed on a day basis, resulting in improved performance.A natural corollary of timestudy is the analysis of methods, and in some cases method improvements have been introduced.It is anticipated that further investigations will be made on methods.INTRODUCTIONIn 1953, a Timestudy analysis of mining operations at North Broken Hill Limited was commenced under the guidance of management consultants. Its aim was, to determine standard time values for specific operations, which would provide management with a measure of productivity beyond the existing measures of tons or feet of advance, and also to determine whether increased output was available under existing operating conditions.

Jan 1, 1956

By J K. de Wet, G Balassone, J D. Singleton, V Arseneau

The Accha-Yanque zinc belt in southernPeru is a major zinc-lead rich metallogenic province. In the belt are comprised several non-sulfide-type occurrences, extending on the periphery of the Yauri-Apurfmac batholith (Oligocene-Miocene). Zinc mineralisation at Accha (almost fully oxidised) occurs in breccias of sedimentary and tectonic origin in the limestone of the Ferrobamba Fm (Middle to Upper Cretaceous). Non-sulfide association consists mainly of smithsonite and hemimorphite replacing both primary ore minerals and carbonate host rocks. Mn(hydr)oxides and Zn-clays (sauconite), can be locally very abundant. Differences in mineralogy of the ore and gangue minerals, as well as the composition of the host rock can have a profound impact on zinc recovery and reagent consumption, and therefore on the economic value of the deposit. An EXTENDED ABSTRACT is available for download. A full-length paper was not prepared for this presentation.

Jan 1, 2008

By C M. Côte, P Bolz, R Chrystal

The design of final landforms is an integral part of mine closure plans in Queensland and aims to ensure the rehabilitated land is safe, stable and non-polluting. Landform stability in this context is commonly assessed using Landscape Evolutions Models (LEM) which are physical models simulating sediment erosion and deposition around individual landforms over long timespans (up to thousands of years). The most used LEM for assessment of rehabilitated landforms in Queensland is SIBERIA (Willgoose, Bras and Rodriguez-Iturbe, 1991; Tucker and Hancock, 2010). SIBERIA models are complex, require very detailed input data and simulate erosion and deposition over time frames that extend decades beyond closure. They are not suitable to assess erosion risks during the operational phase of a mine and to support the development of erosion and sediment control plans. Other types of erosion models, such as the Revised Universal Soil Loss Equation (RUSLE, Wischmeier and Smith, 1978) or Water Erosion Prediction Project (WEPP, Nearing et al, 1989) calculate soil loss on a monthly or yearly basis and are much better suited to erosion management during the operational phase. They are simpler to implement and can support the design of control measures. For instance, designing a sediment basin requires quantification of sediment loads, which can be produced by these models. In Queensland, the legislation around sediment and erosion control for open cut mines is currently tightening. Soil erosion remains a major concern due to potential impacts on the receiving environment. It requires management during operation and for closure consideration alike and it is critical that erosion and sediment control plans are developed with the most appropriate tools. Globally, RUSLE is the most widely used soil loss model (Borrelli et al, 2021). This is because it is an empirical model with relatively simple input requirements: biophysical data such as soil properties, vegetation cover, topography and rainfall variability, which can be directly measured or derived from regional or national databases and/or spatial data sets that are available in most parts of the world. The second most used model is WEPP (Borrelli et al, 2021) but compared to RUSLE, there is a large drop in the frequency of its use. This is because WEPP is physically-based and has more complex data requirements. WEPP integrates hydrology, hydraulics, erosion mechanics and land cover to predict soil erosion and sediment transport on hill slope profiles and small watersheds (Stolpe, 2005). It requires some biophysical parameters in formats different from those of RUSLE, as well as detailed hydrologic and catchment data. Nevertheless, it has been used in landform design for mines across Australia to determine final landform stability (eg Howard and Roddy, 2012; Costin, 2020). In this study, we assess which tool would be the most appropriate to support development of erosion and sediment control plans from operation to closure. We use RUSLE and WEPP to predict soil loss from a mine site, compare the results from both models and outline the advantages of each method.

Aug 2, 2023

By Kohra A, Shoji S

The amount of copper production by flash smelting process occupies about 17% (equivalent to 1.4 million t/year) of total free world production. In Japan, 650,000 tons of copper is produced annually by flash smelting. This is 65% of the gross copper production of Japan. To reinforce pollution control, promote energy saving, and enhance production efficiency by increasing the size of furnaces, conventional blast furnaces and reverberatory furnaces are being replaced with the flash smelters worldwide. The Ashio Smelter started copper production in 1884 and developed in association with the Ashio mine. In those days, the Ashio smelter produced copper by using the blast furnace process designed for the high-grade ore from the copper mine. At that time, this process was specialized in Japan. In 1956, for the first time in Japan, the Ashio Smelter introduced the flash smelting process developed by Outokumpu Oy of Finland (it is suitable for treating the copper concentrate, producing sulfuric acid and improving production efficiency). The flash furnace in Ashio, the first ever in Japan, had a capacity of 230 t/day for copper concentrate and was operated up to 1962. During this period, various operational troubles were solved, and further improvements were made; and, in 1962, a Furukawa-type flash smelting furnace was completed in Ashio. This improved version of a flash furnace had a capacity of 450 t/day. There was one flash furnace and one waste heat boiler, which were arranged in a unique pattern for that time. This furnace may be said to be the prototype of the present flash smelting process in the world.

Jan 1, 1987

The United StatesÆ reporting standard for the mining industry for securities purposes is contained in the Security and Exchange CommissionÆs Industry Guide 7. It defines proven and probable Reserves using its own definitions, and prohibits the disclosure of quantitative estimates, for all mineralisation other than those two Reserve categories (though disclosure of Measured and Indicated Resources as quantitative mineralised material estimates is now informally allowed). Similarly, it restricts disclosure of value estimates to Reserves only, which SEC policy generally requires to be on an historic cost accounting basis. The SEC does not maintain a formal Competent or Qualified Person policy. In March 1999, the US-based Society of Mining, Metallurgy and Exploration (SME) released an update of its 1991 guidelines for definitions to be used in reporting of Mineral Resources, Reserves and Exploration Information, closely abiding by the 1997 CMMI recommendations. However, without SEC recognition, reporting under the SME and CMMI definitions is effectively barred for US companies. The SEC intends to adopt the International Financial Reporting Standards (IFRS) of the International Accounting Standards Board (IASB). This will occur within just a few years, when the convergence project for development of the IFRS has reached a satisfactory point. The US is the largest financial supporter and participator in IASB. The Extractive Industries Standard of the IFRS will likely terminate Industry Guide 7. However, the effect of this international replacement will likely be equally restrictive. This could possibly neutralise the benefit of a CMMI-based global reporting standard. SME, the US society encompassing the widest range of mining industry professionals, does not have a Code of Ethics. It has no mechanism for requiring members to abide by a professional standard. SME is presently looking into possible solutions for this deficiency. US-based professional societies that do have a binding Code of Ethics, generally cater to a single profession, and are not just mining industry related. The American Institute of Professional Geologists (AIPG) and the American Institute of Minerals Appraisers (AIMA) are examples. The SME is considering creating a subsidiary body with an enforceable Code of Ethics. To support a CMMI-based global reporting standard, competent persons will need to work across international borders. A standardised mechanism for qualifying and registering competent persons will be needed. National rules and laws must allow competent persons to easily enter countries to perform their work. State issued licenses are increasingly required for much of the work performed in the US mining industry by engineers, geologists and minerals appraisers (valuers). Such licenses are not required by the SEC for Reserve reporting in the US, may not be required for valuation of mineral properties under certain circumstances, and except for real property valuer licenses, they generally do not have a binding code of conduct. However, state licensing of professionals forms a substantial and increasing barrier to interstate trade in professional services, and can be a prohibitive barrier to professionals from outside the US. Any rationalisation of this confusing patchwork of regulations confronting US minerals industry practitioners will only occur as part of larger, national change, hopefully aimed at compliance with international standards and protocols. The US does not have a valuation standard aimed specifically at the mining industry. The Uniform Standards of Professional Appraisal Practice, the national valuation standards, often must be applied to mineral property valuation, but contains no specific instructions for minerals. The author has campaigned against development of minerals valuation standards proposed by US minerals institutes. Instead he encourages the mining industry worldwide to place its support behind the initiative of the International Valuation Standards Committee (IVSC) to include an extractive industries section in its International Valuation Standards (IVS). This should provide a global set of valuation standards for the mining and petroleum industry within two years. This addition to IVS will provide essential valuation standards reference support for the extractive industries financial reporting standard of the International Accounting Standards Board. The IVS has achieved a high level of acceptance in the developed and lesser developed countries of the world. It provides a comprehensive framework of Generally Accepted Valuation Principles for the valuation profession internationally, for valuation of all property or asset types. IVSC is effectively a sister organisation to IASB. The IASBÆs International Financial Reporting Standards (IFRS), previously known as the International Accounting Standards (IAS), reference and quote IVS in some instructions for determination of fair value. IVSC is a non-governmental organisation (NGO) member of the United Nations and maintains liaison with many important international economic, accounting and financial agencies, such as the OECD, IMF and WTO.

Jan 1, 2002

By M Roberts

The aim of this paper is to evaluate the technical feasibility of application of the electric monorail as a haulage system in hard-rock underground mining in Australia, in comparison to conventional truck haulage systems. The elements of the system being investigated include mine design and layout, installation, loading and unloading subsystems, tramming speeds, cost and productivity, automation, ground support, safety and environmental factors. Electric monorail systems are potentially more cost-effective due to a range of factors: only the one system may be needed for the transportation of workers, material and rock; and excavations for monorail haulage can be smaller and mined at much steeper gradients than for truck haulage. The smaller excavation size also reduces the need for costly ground support and û in another important measure for the health and safety of mine workers, and for energy savings û it reduces ventilation requirements. Electric monorail haulage technology is being applied in hard rock mines in South Africa and considerable benefits have been realised by the industry in that country. In Australia, mine designs for metal mines generally remain based on truck haulage and/or shaft hoisting systems. There is a tendency to apply these haulage systems to every orebody. For the industry to achieve sustained growth against a backdrop of volatile diesel prices and environmental concerns, new generation underground haulage systems are required. The monorail haulage system offers opportunities in improving materials handling efficiencies in underground mining operations. This paper examines the application of monorail haulage in metalliferous underground mining, presents comparative data with track and trackless haulage systems and develops concepts for system application in combination with conveyor belt haulage and narrow vein mining situations.

Jan 1, 2005

The Central West of New South Wales is emerging as a significant metallogenic province. The development of Northparkes Mines (North Limited) and the Cadia Hill deposit (Newcrest) are establishing NSW as a highly prospective porphyry copper-gold province. Exploration in the area has been further buoyed by the Ridgeway discovery by Newcrest near Cadia. The fact that the Ridgeway prospect was discovered 300 m below surface under Tertiary basalt cover indicates that surface prospecting can no longer be considered alone as an adequate method to find significant new deposits.

Jan 1, 1997

During the development of Lorca tunnel project in the South-East of Spain, an in-site study has been done, with the purpose of obtaining the characteristics of the different lithological units through twenty-two parameters for the design of the tunnel excavation and support. In the paper both the different works developed and the different methods and criteria followed in the obtention of the parameters are described. The values of those parameters may be useful in similar cases. Also a summary-table of the parametrical characterization for the use in similar studies is given.

Jan 1, 1987

By D K, S Freij, A Rossiter, X Han, B Feng

In mining operations, the removal of overburden to expose the ores is achieved by rock blasting using ammonium nitrate based explosives, eg ammonium nitrate-fuel oil mixtures, commonly known as ANFO. However, ammonium nitrate can react with pyritic shales that are often found in many mines, leading to premature detonation or spontaneous explosion. In order to minimise the occurrence of spontaneous explosion, the reactivity of the shale in a mine must be assessed. This will provide a better understanding of blasting risks and thus will improve the safety and the cost efficiency of blasting through the selection of appropriate explosives. In this study, shale samples were collected from different locations in Western AustraliaÆs Mt Whaleback iron ore mine and geochemically characterised. The reactivity of the shale samples towards ammonium nitrate and ANFO was investigated using a combination of large-scale firing range tests and laboratory isothermal reactor tests. Results of the firing range tests show that the reactive ingredients of the shale are the limiting factor for the reactions between shale and ANFO. Based on the firing range test results, further isothermal reactor tests were conducted to investigate the reactivity of shale samples towards ammonium nitrate under controlled conditions. Analysis of the results from the firing range tests and the isothermal reactor tests shows that there are correlations between the reactivity of shale samples and several geochemical characteristics such as sulfate, sulfur, ferrous and zinc content.

Jan 1, 2005

Diamond drilling was first carried out at Norseman in the Princess Royal Mine, early in this century. Little concentl'ated drilling was done from then until Western Mining Corporation commenced drilling in 1934. Since then Central Norseman Gold Corporation N.L. has continually employed diamond drilling in exploration of the field. After 1946 the advantage was seen of applying broad pattern surface drilling at Norseman in the reef exploration. In 1953, as a result of the steeply rising cost of drilling and the time taken to penetrate surface material by light equipment, heavier drills and new rigs were introduced. The surface drilling programmes called for a greater monthly or annual footage and to satisfy this new techniques were introduced. The Mitchell-21 machines were discarded and A-3000 machines were installed, firstly under a 48 ft. fixed tower, then mounted on a truck with a 20 ft. tower, and finally on a truck carrying a 40 ft. tower. With the mobile units a compressed air compressor is attached. By use of compressed air with either the Reed roller or Hawthorne bit, rate of penetration of overburden is greatly increased. The mobility of the truck mounted machines has greatly reduced the time required to move from one hole to another, and the use of heavier machines on a three shift per day basis has considerably increased the footage per shift. The general result is an increase to 1,500 ft. of drilling per month per machine, while costs have been greatly reduced in spite of increased wages and diamond prices.The underground drilling technique is described. Analysis of performance has not been made because the drillers performance is subject to shaft routine and service.INTRODUCTIONGold was first discovered at Dundas in 1894, and at Norseman, 14 miles north, in 1895. From that tirpe until 1935 mining activity fluctuated. Following the mining revival in 1935, production in the field has remained comparatively stable. This stability in part has been due to the broader scale of operations of Central Norseman Gold Corporation N.L., and in these operations diamond drilling has played an increasingly important role.

Jan 1, 1956

By A Richmond

"In some lode-style gold deposits the geological (lithological) uncertainty may have similar economic significance as the grade uncertainty. In the absence of precise knowledge of the deposit geology, geological models of these types of deposits that are used to constrain spatially the estimated (or simulated) grade values may influence significantly the contained metal. Methods for assessing geological uncertainty quantitatively are rarely considered due to their perceived inability to consider exhaustive geological interpretations, and resulting models that often appear geologically unrealistic. Furthermore, should the lodes have been subjected to folding, or where the mineralisation continuity does not follow a planar orientation along strike or down dip, standard methods of variography and interpolation using linear vectors in space often do not provide a good representation of continuity. An alternative approach is to relate spatial samples from adjacent drill holes using an unfolding plane.The paper demonstrates conditional simulation of the geometry and gold grades of a folded lode-style deposit where:simulation of lode geometry considers explicitly the geologistÆs interpretation, andsimulation of gold grade values that consider explicitly the folded nature of the lodes.The results are contrasted to the traditional approach of linear vectors in real space for a single lode interpretation.CITATION:Richmond, A, 2012. Conditional simulation of a folded lode-style gold deposit, in Proceedings Narrow Vein Mining 2012 , pp 149-154 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Mar 26, 2012

This paper looks at the various stages of development of open stope drilling techniques. Due to the structural nature of the orebodies mined by open stoping it has been necessary to review mining methods. In-the-hole hammer drilling proved to be the solution to many problems encountered in horizontal percussion drilling.

Jan 1, 1977

The Savage River open cut magnetite mine is located in rugged terrain in densely rain forested northwest Tasmania. The mine and concentrating plant are both in the Savage River valley. Pickand Mather Incorporated (PMI) operated Savage River as an open cut magnetite mine between 1966 and 1996. Acid rock drainage (ARD) was first noted in the last ten years of the operation, leading to elevated concentrations of heavy metals downstream of the mine. When operations ceased in 1996, PMI returned the mine to the Tasmanian Government along with a remediation fund of $11.4 million. At that time, the assessed cost of remediation was in excess of $120 million. As a result of the ongoing ARD contamination and to facilitate both a new operation and effective remediation, Goldamere Pty Ltd negotiated an agreement with the Tasmanian Government in 1996, which resulted in the Goldamere Act and the Goldamere Agreement. The agreement has allowed Australian Bulk Minerals (ABM) to remediate the Savage River mine in conjunction with the Tasmanian Government while re-invigorating a previously closed mine by providing ABM with an indemnity against past pollution. ABM can configure its mine and waste planning activities to maximise remediation benefits without fear of future litigation for past mistakes. The effect to date has been the development of a long-term strategy to remediate the Savage River and short-term remediation works such as water management, which provide benefits to the ecosystem. After five years, the Savage River is no longer significantly impacted by ARD for 30 kilometres downstream and trout are now reported within the reaches of the mining lease. The arrangements between ABM and the Tasmanian Government are an example of a genuine WIN WIN situation where co-operative environmental management of the site results in significant improvements and where the æregulatorÆ and the æminerÆ are working together to achieve mutually beneficial goals. The end result is a significant benefit to Tasmania.

Jan 1, 2003

Fission track thermochronology is a well established method for reconstructing the thermal histories of rocks with particularly important applications in tectonic studies, detecting low-grade thermal events, sedimentary basin analysis and resource exploration. These applications take advantage of the limited stability of fission tracks, especially in apatite, when exposed to the temperatures found in the upper 3-4 km of the crust. Apparent fission track ages in apatites can define an invisible 'stratigraphy' in otherwise homogeneous rock masses that can give valuable information on thermal, tectonic and erosional events. Quantitative modelling of the thermal annealing of tracks in apatite shows that distinctive profiles of apparent fission track age can be related to a number of simple thermal history styles. The main types of profile observed tend to be either an essentially linear decrease of apparent age with increasing depth, which relates to continuous uplift and denudation, or a concave-upwards profile produced by partial annealing in environments of tectonic stability or burial. More complex thermal histories produce compound profiles which are essentially just combinations of these two elements. Track length information allows the apparent age profiles to be interpreted in much greater detail. Examples of the major profile types have now been identified in various geological environments and can be analysed to give information about, for example, uplift and denudation rates, the timing of uplift or low-grade thermal events and maximum palaeotemperatures experienced during burial.

Jan 1, 1990

In making any attempts to determine the depositional environments in which coal seams accumulated it would be useful to establish whether there is a pattern, or patterns, of development which the majority of the seams have followed. To this end, the distribution of types of coal seam sequences found in the standard petrographic profiles of about a hundred Australian coal seams of Permian and Triassic age has been examined statistically, using the "chi square test" with the limiting probability set at O·Gl.Results indicate that non-random conditions have probably prevailed during the deposition of most of the seams. More samples are needed for conclusive results.The plants, or some other internal feature of the swamp environment, have been the important controlling factor in the development of the seam sequences.Comparison has been made with some British Carboniferous coals.

Jan 1, 1972