Search Documents

The Australian underground contract mining industry has grown from almost nothing 25 years ago to the point today where half the countryÆs underground mines are using contractors to produce their ore and do their development. This growth was driven by the need to change poor industrial relations and work practices in sectors of the industry, along with the needs of many small gold mine owners to preserve their capital by using contractors to do their mining. The industry is dominated by two major privately owned contractors with a number of other publicly and privately owned contractors making up the balance of the market. This paper discusses the important trends in the contract mining industry and the directions it may take in the next few years.

Jan 1, 2005

By V S. Svinin, V V. Rybin, V A. Maltsev

In large-scale mining, large-sized intermediate pillars, or block-pillars, are generated on the horizon or between closely located mines. These pillars are mined under high rock pressure that results from the stress concentration zones superposition from closely located working excavations. This problem becomes much more complicated if high tectonic stresses occur in the rock mass inducing a rock-burst risk situation. Mining experience gained in mining seven block-pillars at three Khibiny mines in Russia under the geomechanical situation like that described aboveÆ is discussed in detail. It has been shown how safe mine of block-pillars depends on their width, location relative to significant geological failures and uncaved rocks of the hanging wall, the order of pillar recovery, and application of special measures for rock mass stress relieving. Basing on the analysis of the mining experience and special scientific researches, the basic principles are worked-out for safe block-pillar mining under rock-burst prone conditions.

Jan 1, 2000

By A D. Farmer

Power ultrasound may be used in a number of ways to enhance the processing of minerals. It is both technically and commercially feasible to apply ultrasound to leaching processes in order to enhance the removal of contaminating minerals, or the rate and ultimate recovery of valuable mineral. When applied to the production of synthetic rutile from reduced ilmenite produced by the Becher process, its use proved beneficial to both the aeration and the final acid leach process. The enhanced performance is achieved through the very localised high energy release at the mineral surface from the collapse of cavitation bubbles produced by power ultrasound. This gives rise to two effects: initially, the rapid cleaning of mineral surfaces û of oxidation products and coatings of fine adhering gangue minerals û and the attenuation of the boundary layer at the mineral surface during leaching, which allows fresh leachant to contact the surface more readily.

Jan 1, 2000

By Huafu L, Ruishi N, Hongnian Y, Qinglong Z, Yangshen S

The Dongshan terrane was first recognized in 1984 (Guo,et al., 1984, 1989) as an old continental crust block of migmatized granitic gneiss in the Southeast Coastal Hercynian-Indosinian orogen, and it was thought to have occured on Dongshan Island, which has an area of less than 100 km? Recent research work has shed much light on the geology of the Dongshan terrane.The Dongshan terrane is approximately 40-50 km wide and 380 km long, trending NE. It runs from the region of the mouth of the Ming River through Putian and Huian Counties, Amoy and Dongshan island of Fujian Province to Nanao island of Guangdong Province, bordering the southern segment of the coastal region and coastal islands of Fujian and eastern tip of Guangdong Province. The Dongshan terrane is divided from the Zhejian-Fujian Mesozoic Volcanic Mountain Chains by the Changle-Shaoan fractural zone, and its eastern boundary is covered under water in the Taiwan Straits.

Jan 1, 1990

By Connor J. W

Nifty Copper Operations was established to treat a copper orebody situated in the East Pilbara area of North West WA, located approximately 70 km west of Telfer in the Great Sandy Desert. The plant was designed to treat the oxidised portion of the orebody with underground development following at a later date. Nifty was designed to produce 16 500 tpa of copper cathode. This will increase with treatment of the chalcopyrite ore (underground resource). Ore processing is similar to other operations of this type but has its unique challenges. Problems discussed are: fine clay minerals which hinder percolation; oxidation of organic by manganese in the electrolyte; crud formation by clays; third phase emulsions; and organic carryover into the electrowinning tankhouse. As the orebody utilisation progresses, some sulphide material will require leaching and further investigations into liquor chemistry.

Jan 1, 1996

By S Leary

Diamond drilling since early 2006 has identified an epithermal gold-silver (Au-Ag) deposit beneath 140 m to >400 m of cover. The Fruta del Norte discovery had an inferred resource estimate of 58.9 Mt grading 7.2 g/t Au in October 2007. The mineralisation is hosted by Mid-Late Jurassic andesite and andesite porphyry in a regional fault zone beneath mainly post-mineral but in part syn-mineral Late Jurassic cover. The intermediate sulfidation-style deposit formed before and in part during deposition of epiclastic cover in the fault related pull apart basin. In addition to its size and obvious economic importance, the widespread occurrences of visible gold and exquisitely preserved epithermal textures will make Fruta del Norte an important learning tool for explorationists seeking epithermal mineralisation in theAndes and elsewhere. An EXTENDED ABSTRACT is available for download. A full-length paper was not prepared for this presentation.

Jan 1, 2008

By G B. Siddall

The paper examines the current state of equipment and circuit design, with reference to Australian practice. Following a review of the changes in milling applications over the last 15 years, developments in mill design are examined. Current issues include trunnion versus shell support; drive type and economic analysis for comparison of the various systems; the efficiency of the mill discharge system for slurry and pebble removal, and lining configuration. Peripheral problem areas such as pebble crushing and classification are briefly examined. Circuit design issues are reviewed. The decision to modify the traditional primary crushed feed is examined with reference to recent and proposed installations. A retrospective look at fully autogenous installations and their successes is presented, and current views on increasing throughput are assessed. Finally, future developments are anticipated in mill design and control, and competing processes are identified.

Jan 1, 2002

By M L. Habner, S D. Munro

In a gold CIP/CIL circuit, adding new circuit water to a final tails thickener and then directing the thickener overflow to the head of the circuit significantly reduces the cyanide concentration at the TSF discharge spigot. The new water is used to dilute the final tails. The dilution and recycle of the tails in this manner may have the added benefit of reducing reagent consumption, in some cases to the point where the reagent savings justify the expenditure and Cyanide Code compliance is achieved at no extra cost. Potential circuit configurations and water recycles can be modelled by splicing a flowsheeting and thermodynamics package, such that changes to the composition of the water can be reduced to chemical speciation with a Gibbs free energy minimisation enabling a complete understanding of the circuit water chemistry.

Jan 1, 2007

More than ten seafloor massive sulfides (SMSs), which tend to be enriched in Au and Ag with varying amounts of Zn, Pb and Ba, have been reported in Japanese Exclusive Economic Zone (EEZ) including the Jade hydrothermal field in the Izena cauldron Okinawa, theSunrise deposit in Myojin knoll Izu-Ogasawara, and other active deposits found in the past 20 years. From the fiscal year 2008 some universities in Japan will begin development of sensing devices to delineate surface distributions of known SMSs and to find new ones. The devices would be deployed by an autonomous underwater vehicle (AUV) or remotely-operated underwater vehicle (ROV) later in active hydrothermal fields and potential areas in the EEZ. On the other hand, different laboratories are planning to research and evaluate SMSs with state-of-the-art methods such as the benthic multi-coring system and geophysical devices to collect information in deeper parts of the SMSs. In this session recent projects on exploration and evaluation of SMSs with some new trials including geophysical and geological surveys in Japan will be reported. An EXTENDED ABSTRACT is available for download. A full-length paper was not prepared for this presentation.

Jan 1, 2008

The paper discusses the use of animated dynamic numerical simulations to support design and operational decisions in the mining industry. The basis of the simulations discussed is a queuing theory engine with added features that enable continuous processes to be included in simulations. This approach is well suited to the needs of the mining industry which has a mixture of discrete events interfaced to a variety of continuous processes via various forms of surge capacity. Examples are given of the benefits of animation in communicating concepts to those with limited domain knowledge and simulation as a tool that facilitates the sharing of understanding between the stake holders of a system. The analytical content of the paper addresses conflict for resources within systems, the constraints imposed by human and other types of resources, and the impact of external events. Examples are presented showing the use loop diagrams and Gantt charts in the recognition conflict, and its causes. and the use of utilisation logs to identify opportunities for cost reduction.

Jan 1, 2009

This paper quotes the results of many years of experiments and observations concerning ore drawing from mining blocks in major ore deposits mined by bulk induced caving of ore and country rock. Numerous laboratory and commercial test results of Russian, Ukrainian and Kazakh mines have been used and processed. Over 35 per cent of all ferrous, non-ferrous and other ore mined in the Russian Federation by the underground method is drawn underneath overlying caved rock (including ore drawing after bulk caving of pillars). The complexity of the process denies a logical or engineering calculation answer to many commercial production questions. Hence the massive research of ore drawing issues targeted at ore recovery forecasts in specific instances in order to assess an engineering solution or to define the design or planned ore draw performance. At first, the conditions were pictured as ideal. Subsequently, it was attempted to take into account the side contacts of ore with the country rock and the caved barren rock, the small size stuff in the caved rock, the unevenly loosening ore, end draw, and so on. The ore draw information available provides ample qualitative characteristics of the phenomena and only approximated and partially quantitative characteristics for individual cases. Many specific situations require individual studies of subject specific models.

Jan 1, 2000

Groundwater issues for the mining industry are many and varied. When the depth of mining is below the water table/potentiometric surface, a groundwater æsinkÆ is created which alters the local groundwater flow regime resulting in minewater inflows. Assessment of mine dewatering, mine water balance and wastewater disposal requirements are central to the effective management of water in a mining operation. Each of these issues has a significant groundwater component. Other groundwater issues for mining operations include: water supply, aquifer storage and recovery, the impact on other groundwater users in respect of groundwater levels, bore yields and water quality, and the development of an effective groundwater monitoring network for early detection of impacts and to satisfy regulatory requirements. This paper outlines the techniques involved in assessing groundwater issues for project feasibility, during operation and post closure, and provides an overview of several mine dewatering and water disposal methods. The practical assessment of groundwater issues for the mining industry is illustrated with several case studies of mining projects in Australia, SE Asia and the subcontinent. These are projects to which the author has contributed during a career as a geologist/hydrogeologist spanning more than 25 years.

Jan 1, 2003

Major changes occurred in the management of loss prevention and risk management at operations in North and South America due to increased insurance premiums following the Olympic Dam fire in Australia in 2001. There are many different scenarios on how fires can develop and the estimated maximum losses (EML) those fires can incur. The EML is utilised by insurance companies to determine the cost of insurance premiums. The cost of insurance can be controlled at existing and newly designed solvent extraction (SX) plants by using risk reduction methods and design criteria to limit the fire exposure. A review of data collected during several loss prevention risk assessments can show how a budget can be protected from dramatically increased premiums and see which design of SX plant and fire protection standards best apply to your operations. The paper will investigate the pitfalls of existing materials of construction, capacity, geography, management practices, fire risk minimisation, and fire suppression systems. Intelligent engineering and managerial improvements implemented by the operations in the Americas in the past two years have further minimised the fire potential and benefited companies in insurance renewal negotiations.

Jan 1, 2003

In the human body, the balance between heat production and heat loss is continuously being disturbed, either by changes in metabolic rate (work being the most influential) or by changes in the external environment (heat stress), which alters heat loss. These changes in body temperature can adversely affect the function of body systems and organs. As a result, heat production or heat loss processes are triggered in order to restore normal body temperature (36 - 37¦C). If the heat generating systems of the body are excessive or the environment hostile then the capacity of the body to maintain thermal homeostasis is exceeded and can lead to a serious threat to health, or even death. This health deficit can severely affect an individualÆs capacity to work optimally; the end result is both poor productivity and health. Strategies to minimise or eliminate this effort will benefit both the health of workers and the productivity of companies. The principal strategies to reduce the effects of the environment on workers are: engineering interventions: to improve environmental conditions and reduce heat stress; and a comprehensive working in heat protocol: with provisions to identify risk situations and procedures to be adopted in relation to these. The above points will be discussed in detail with practical and simple strategies proposed to combat the deleterious effects of heat in mining.

Jan 1, 2005

Accounting for borehole damage in analytical modelling of explosively generated stress waves is important for predicting the finer details of the stress wave patterns observed in the field. The classical Sharpe's [19421 concept of an effective borehole larger than the initial borehole diameter has been widely accepted to explain material damage around a borehole. A new analytical model based on dynamic compaction is advanced to predict far-field stress wave patterns. This model supports field data corresponding to reduced frequency of oscillations and increased damping. The present model recovers the earlier result when compaction around the borehole representing borehole damage is ignored.

Jan 1, 1990

Geotechnical practice combines the site engineering geological model with engineering design and operations to control risk. The responsibility of the geotechnical professional is to present relevant engineering geological information to an engineer to effectively impact an outcome. Return is enhanced by understanding expected operating and capital cost due to ground conditions.   Risk is effectively communicated by a successful geotechnical practitioner. In a mining environment the need is to assess ground conditions accurately and quickly, and to effectively communicate expected ground response due to mining. A good engineering geological model includes a description of geotechnical engineering parameters to design assuming reasonable expected soil, rock and water conditions. Pit slopes are steepened, stope spans widened and waste foundations and land forms are constructed all under geotechnical control.   The responsibility of the geotechnical professional is to collect, assess and disseminate relative engineering geological information. The geotechnical professional is a person advising on ground related engineering, and generally operates within geology and engineering end members.   Return is better assessed on an understanding of ground cost. In operations the goal is to meet production at lower cost. In evaluation, regional and exploration geology, mine design and expected operational factors influence expected cost and project return. Return allows companies to meet shareholder expectations, attract equity to develop and add value to the community.   This paper presents a discussion with some examples to present an approach and design philosophy for geotechnical practice in the mining industry.

Jan 1, 2004

By P D. Munro

The Mine to Mill concept, as it has become known, is a philosophy which is being increasingly embraced by mining companies committed to increasing their profitability through better integration and global optimisation of their mining and processing operations. Autogenous (AG) and semi-autogenous (SAG) mills are the principal primary grinding devices currently in use, their performance is particularly sensitive to feed size distribution. Most efforts to-date have centred on modifying and controlling the run-of-mine (ROM) size distribution to maximise grinding mill throughput. The complexity of the interaction between ROM size distribution, primary crusher product and AG/SAG mill performance precludes the trial-and-error approach as an effective means of determining the optimum blast-induced fragmentation size distribution. To overcome this limitation, the Julius Kruttschnitt Mineral Research Centre (JKMRC) has developed modelling and simulation techniques that are able to accurately reproduce both the fragmentation processes during blasting and the subsequent performance of the comminution circuit. These models are tailored to suit local ore types, rock structure and comminution circuit design and calibrated using high quality field data. MIM Holdings Limited (MIM) have been particularly active in the Mine to Mill area and have instituted optimisation programs at three of their associated base metal operations viz Alumbrera, Ernest Henry and the Mount Isa Mines. This paper describes these programs with particular reference to the data acquisition and modelling phases, the predictions of potential productivity gains and the extent of the realisation of these gains to-date.

Jan 1, 2000

Metallurgical accounting can be defined as the monitoring of the valuable metals from the time the ore is broken at the primary crusher until the time that we have the saleable products and residues. The overall purpose of metallurgical accounting is to provide management with up-to-date inform- ation that can be used to control mining and metallurgical oper- ations. The decisions that are taken on the basis of the information that the metall- urgical accounting system provides should result in improved control and, ultimately, increased revenue. The current state of accounting is a result of an extended evolutionary process and will continue as process plants bec- ome more sophisticated. Differences in mine æcall factorsÆ and grade control reconciliation can lead to frustration between the siteÆs geoscie- ntists and its metallurgists leading to a level of distrust in the mill grade. Metallurgical accounting is not included in sufficient detail in undergraduate courses and the acceptable industry standards have developed based on what is considered acceptable to industry personnel and consultants. There is now the AMIRA P754 Metal Accounting, Code of Practice and Guidelines Handbook or reference manual. Computer based databases and spreadsheets have transformed tedious bookkeeping into an important management tool. Over time these standards have improved with developments in analytical procedures, weighing technology and sampling. This paper provides anecdotal examples of problems and improvements observed over a number of years within the gold industry in Australia and overseas.

Jan 1, 2009

All minerals contain radioactive elements, from the uranium ores of the Gabon, which contained sufficient uranium to initiate a natural nuclear reactor, to the very low levels of some recent evaporites. The commonly occurring heavy minerals such as ilmenite, rutile and zircon are no exception to this and contain varying qualities of radionuclides, depending on the source. With recent changes in legislation many natural minerals may become officially classed as radioactive. Such moves can inhibit the sales and exploration of many minerals in the heavy minerals suite. The many negative perceptions associated with the word radioactivity can produce an over cautious reaction from regulators and users. This paper presents a method of managing the radioactivity issues associated with minerals such that the safety aspects of workers and public are not compromised, whilst allowing the commercial use of such minerals to continue in a sensible manner. The paper focuses mainly on the mineral zircon and its uses. However the legislation changes particularly in Europe and the USA have the potential to affect all minerals imported into or produced in those countries. The model developed for addressing the issues of zircon radioactivity may be readily applied to other minerals since legislation governing such matters is not mineral specific. There is a strong need for education of both regulators and users of minerals. Regulators are usually not aware of the specific properties or uses of individual minerals. Similarly mineral users are not aware of the radioactive nature of their materials or how to manage this property. The paper concludes by recommending strong cooperative action by both producers and users of minerals to protect the future of their industry.

Jan 1, 2001

The mining industry has had lengthy experience with risk management involving technological situations imposing risks to people and property. In such situations the relevant parameters can be fairly well defined, the outcomes can be broadly predicted and probabilities of these can be estimated. Accordingly quantitative risk assessment can be applied. In recent years there has been increased emphasis in risk management on a broader set of potential consequences. These include potential impacts on the flora and fauna of ecosystems. These are typically poorly understood and this is especially true in Australia where the vast size of the continent and sparse population make gathering a comprehensive data base on biological resources a difficult task. The resulting scientific uncertainty and ignorance regarding the potential for serious or irreversible harm to the environment mean not only that quantitative risk analysis techniques are not appropriate, but also that the precautionary principle (PP) needs to be applied as a complement to qualitative ecological risk analysis. The potential for significant impacts is particularly high in Australian ecosystems. These comprise one of the 12 æmegadiverseÆ regions of the world in terms of biodiversity and, hence, have global significance. Moving from risk management to application of the PP by the mining industry provides a significant challenge. Application of the PP has no clear guidelines to follow and, to-date, has been highly unpredictable. However, there is much to be gained for industry in embracing this challenge and taking a pro-active approach in exploring methods that will provide for clearer guidelines and hence more certainty in outcomes of environmental management decisions involving precaution. As well, there could be considerable other advantages for the mining industry in terms of reputation assurance, community acceptance and greater certainty in terms of access to resources.

Jan 1, 2000