Search Documents

By A. Rousselet, H. Gilbert-Tremblay, A. Berton

"Robex Resources interrupted production at the Nampala Mine in September 2014 following throughput and gold recovery results which were below expectations during the first months of operation. After a thorough plant audit, an important brainstorming took place in order to identify an economical path to resume production. It was clearly identified that a significant investment was necessary at the concentrator prior to restarting the plant, namely the addition of a ball mill and a new elution system.The mineral processing simulation software USIM PAC was used in order to simulate the grinding circuit in design. The simulations’ outputs allowed the ball mill characteristics and the surrounding classification devices to be designed with more accuracy. Many ball mills available from second hand retailers were therefore studied in the simulated circuit. The chosen ball mill, which was in perfect condition, had the advantage of being available for rapid delivery on site.The paper first describes the ball mill sizing method in comparison with the conventional Allis Chalmers method. It then describes the phase 2 concentrator start-up (that took place in 2016) with the commissioning of the ball mill, the classification circuit, the gravity concentration, the four (4) new carbon-in-leach (CIL) tanks, and the Zadra elution system (The phase 1 start-up took place in 2014). It finally provides production data compared to expected simulation data, as commercial production was reached in January 2017.IntroductionDesigning a new concentrator or new equipment within an existing concentrator requires significant efforts to identify possible bottlenecks and their causes (i.e. limiting equipment or sectors) and accurate sizing of major equipment can have a tremendous impact on the economy of the whole project. In the presented case study, the ball mill was the critical equipment and oversizing it could have brought the Capex to a level where the project would not have gone through. Inversely, undersizing the mill could have resulted in lower production and therefore no economic viability for the project once it is in operation.During engineering studies, equipment sizing often relies on a static mass balance and one-by-one sizing of all pieces of equipment. The sizing is then left to the equipment manufacturer or in the case of mills, evaluated with empirical models mostly relying on the Bond equations (Allis Chalmers method) [Rowland and Kjos, 1978]. This methodology shows the disadvantage of not considering interaction between equipment in a mineral processing circuit, especially when recirculation occurs. Also, it has the disadvantage of not using the more advanced grinding models that include the use of the whole particle size distribution as well as phenomenological components by only using limited parameters in the ore particle size distribution (i.e. the P80). This can be explained by the lack of data that sometimes needs to be gathered in order to tune the more advanced models but also by the conservative mindset in mineral concentration engineering which does not always favor the use of process simulation. In many aspects of process engineering, Soutex has demonstrated its affinity to using simulation in order to size equipment with more accuracy, consider process variability, simulate complex systems, and study supply chain management (Berton et al., 2015)."

Jan 1, 2018

By Henri-Louis Jacob

Le secteur des substances non-metalliques repose au Quebec sur !'exploitation et la transformation d'une dizaine de mineraux ainsi que sur la production de materiaux de base destines surtout a l'industrie de la construction. L'ensemble de cette production representait en 1982 une valeur estimee a plus de 797 millions $, soit tout pres de 400Jo de la production minerale du Quebec. L'amiante et Jes scories de titane destines a la production de pigments, qui comptent parmi Jes plus importantes substances minerales produites au Quebec, representent respectivement 370Jo et I 70Jo de la valeur totale des non-metalliques tandis que le groupe des materiaux de construction represente pres de 400Jo. Les autres substances, parmi lesquelles ressortent nettement la tourbe, la silice et la magnesite, representent une valeur totale de 61.5 millions $.

Jan 1, 1984

By R. Spring

"Soft-sensors are a computer software alternative to inadequate hardware instrumentation. Filters are averaging methods that reduce the noise in any sensor's signal. This paper introduces these topics and places them in a mineral processing context using then-product formula.Soft SensorsAs their name implies, ""soft-sensors"" are computer programs that estimate values for process variables (Tham, 1991). This approach is useful when the appropriate hardware sensor does not exist, is deficient, supplies only infrequent values, etc. For example, in mineral concentrators the traditional magnetic flowmeter/ nuclear density gauge instrumentation for measuring slurry flows costs $5,000 or more per flow and requires frequent maintenance. However, metal assays are commonly available from online X-ray fluorescence analyzers and application of the n-product formula (Taggart, 1945) to these assays conveniently provides software estimates of the flowrates (albeit only when the circuit is in steady-state).Soft-sensors are used by inferential controllers that base their control actions on the process values ""inferred"" by the soft-sensor. Such was the case at Brenda Mines where the rod mill feed tonnage controller used an inferred value of the cyclone overflow particle size (Bradburn, 1976). It was also the case at Brunswick Mining where reagent controllers adjusted reagent addition rates throughout the plant according to the various ore flowrates inferred by an expert system (Spring, 1991). A unique feature of the expert system soft-sensor was its dynamic flow models which compensated for residence times, material transport lags, etc. Thus the soft-sensor values were valid under both steady-state and nonsteady- state conditions."

Jan 1, 1992

By M. Hozayen, E. S. Radwan, P. A. Nawrocki, A. Jebbouri

"A major geomechanical study was conducted for one of the UAE onshore oil fields with the purpose of studying reservoir rock properties and stress distribution, based on which a 3D coupled reservoir geomechanical model was built. This model was later used for wellbore stability analysis and for analyzing the effect of fractures on future reservoir production performance, including fracture deformation and permeability evolution occurring due to reservoir depletion and resulting changes in local stress field. The subject of this study was a complex fractured Upper Cretaceous carbonate reservoir characterized by high degree of heterogeneity, both vertically and laterally. Wellbore instability related drilling problems were encountered while drilling the wells in this field. The problems were mainly in drilling the horizontal wells, including breakouts and mud losses. Experimental results of laboratory tests are summarized in this paper whereas wellbore stability analysis and formulation of a 3D geomechanical model that was built for that purpose is summarized in a sister paper (Part II).A suite of tests reported includes tensile strength, uniaxial and triaxial compression and permeability under stress at simulated reservoir conditions. All tested rocks have been grouped into twelve test units and reservoir geology, rock types and challenges related to designing a viable sampling and testing program for a big reservoir are discussed first followed by sample selection criteria and details of the testing program. All test units showed brittle behavior at zero confinement and some samples showed similar behavior at low confining stresses. With confining stress increase, the behavior gradually turned to plastic but some samples showed features of ductile behavior even at low confinement.Obtained experimental data have been summarized in the form of strength criteria and correlations. The Mohr-Coulomb strength equations were obtained for each test unit and also for the averaged values. It was noticed that triaxial compressive strength (TCS) increases with decreasing porosity or increasing density but their influence on TCS is getting smaller with confining pressure increase. Good correlation of porosity and density with Young’s modulus, Poisson’s ratio, unconfined compressive strength (UCS), friction angle, cohesion and tensile strength has been noticed and there was an increasing trend between the confining pressure and TCS. Rock type (mud or grain supported) was not influencing the TCS as much as porosity and density and the two lithologies encountered affected TCS approximately in the same way. These results and correlations are summarized and explained in this paper. They were further used in the numerical modelling part (Part II) of this paper, Hozayen et al. (2015). It is also concluded that rock lithology is not a decisive factor and mechanical properties of tested rocks should be rather considered dependent on porosity and permeability. This helped greatly in reducing the number of tests that had to be performed."

Jan 1, 2015

By R. Minto, W. G. Davenport

The slag removed from the reverberatory furnaces of copper smelters contains significant copper values. A serious financial loss is involved, as further recovery operations are not normally carried out. This paper describes the factors affecting physical transport of matte into slag by gas bubbles, and the subsequent entrapment and flotation of matte drops. Three distinct patterns of transport behaviour have been identified from studies of a number of liquid/liquid systems, including liquid metal and liquid matte systems. A theoretical approach is proposed to explain these behaviour patterns, and to predict transport and entrapment behaviour in matte/slag systems. The concepts of "Film Coefficient" (ø) and "Flotation Coefficient" (?) are introduced. The effects of smelting process variables on the physical loss of copper matte in slag are also discussed.

Jan 1, 1972

By M. U. Oko

"Monitoring of all the waste streams from Falconbridge's Sudbury Operations to determine whether they meet the required standards, has been performed for many years. By 1969, however, the number of samples being collected had become so large that a complete revision of the existing systemwas necessary. Sites previously designated by name only, were numbered, clearly marked on the ground and on maps which were circulated to all concerned. The types of pollutants analyzed were determined and specified for each sampling location and a chemical analysis report form was designed. The sampling schedule has been computerized to produce a periodic listing of the samples to be taken and the analyses required.An area map showing sampling sites, chemical analysis report form, spill report and a computer print-out example are shown and explained.EVOLUTION OF FALCONBRIDGE'S WASTEWATER. MANAGMENT SYSTEMFalconbridge Nickel Mines employs some 4500 people, operates nine mines, four mills and a smelter in the Sudbury basin. The operations are geographically fragmented into four widely separated locations, the Falconbridge operations east of Sudbury and the Onaping operations in Levack Township being the two largest of the four. The Lockerby area located to the west and the Lindsley Mine just north of Sudbury are now under development. The magnitude, the diversity and nature of the operations are such that constant vigilance is needed to prevent inadvertent damage to the environment. The purpose of this paper is to describe the information system used to monitor and control waste-water disposal on Falconbridge's properties to help ensure the maintenance of effluent standards satisfactory to the Ontario Water Resources Commission (OWRC) and to the Ontario Department of Health."

Jan 1, 1971

By B. W. Steele

"Dofasco began operations in 1912 as a steel foundry located in Hamilton, Ontario. Today, Dofasco is a fully integrated mill that manufactures hot rolled, cold rolled, galvanized and tinplate steels. Customers include the automotive, construction, tubular, manufacturing, appliance, packaging and steel ser-vice centre industries. Raw steel production and purchased semi-finished steel processed in1994 was 3.5 million net tonnes. Dofasco employs 7300 people at its Hamilton facility.Environmental management at Dofasco is guided by its environment policy and associated commitments. This paper discusses Dofasco’s responsibility for its products as it relates to these commitments. Dofasco is com-mitted to:n the principles of sustainable development that require that activities be conducted in a manner that provides for the present without compromising the ability of future generations to meet their needs. These principles will be integrated into product design, manufacturing and business planning;n managing renewable and non-renewable resources through the responsible application of reduce, reuse, and recycle principles;n minimizing any potential impact of its operations and products on the environment, employees, customers and the community;n continuous improvement of the effectiveness and integrity of our environmental management systems;n developing understanding among all employees about their responsibilities, and assigning the necessary authority; andn meeting the standards set by relevant legislation and international agreements through participation with governments and the diligent application of economically feasible and scientifically sound methods and technologies."

Jan 1, 1996

By Michel Dostie

Un séchoir à vis chauffé par induction électromagnétique a été développé et implanté chez Mines Niobec pour le séchage d?un concentré de niobium. Ce séchoir a permis une réduction des émissions de poussières et des gaz à effet de serre de l?usine. Il offre une grande souplesse de contrôle, une meilleure efficacité énergétique et peut être utilisé pour le séchage de granulats, de poudres ou autres substances habituellement traitées dans un four rotatif ou à l?aide de vis chauffées par un caloporteur. Le principe de fonctionnement du séchoir est simple. Trois inducteurs opérant à la fréquence du réseau électrique assurent le chauffage des parties métalliques du séchoir, dont des vis qui servent à convoyer le matériel. Le contact du matériel avec les parties métalliques chaudes permet le transfert de l?énergie requise pour le séchage. La conception de ce type de séchoir requiert un équilibre adéquat entre les besoins associés au chauffage par induction et ceux liés au transfert de chaleur par contact et au transport du matériel dans le séchoir. Cette première implantation industrielle a nécessité des efforts de développements importants et une collaboration des différents intervenants. Une revue des principes de conception, des difficultés rencontrées et des performances obtenues sera présentée.

May 1, 2007

By Martin Encinas, Jesús L. Valenzuela, Jose R. Parga, Salvador Aguayo, Roy G. Lewis

Continuous laboratory solvent extraction of gold from cyanide solutions using LIX?79 guanidine based extractant has been investigated. Different variables that affected the selectivity and extraction include aqueous pH, extractant concentration, and modifier concentration. The extraction isotherms of the aurocyanide complex with respect to the other cyano anions were compared, and the following order of selectivity Au > Ag > Zn > Cu > Fe was observed. According to the pH isotherms, aurocyanide can be extracted in an alkaline media, and a better separation with respect to the other cyanoanions was obtained in the pH range 10.5-11.2. From the McCabe Thiele diagrams, better recovery was predicted when using LIX?79 extractant and tridecanol modifier at 10 vol.%. Stripping of the gold from the loaded organic was carried out at pH > 12 using NaOH and NaCN solution. The continuous tests indicate that a two-stage extraction followed by a single stage strip is adequate to obtain an overall process efficiency of >90%. Better results were obtained using a copper wash stage before gold stripping.

Jan 1, 2014

By Osvaldo A. Bascur

Industrial complexes rely on measurements of flow rates, qualities, and concentrations for monitoring and optimizing their operation. Corporations use the data from the various sensors and measurements to make business decisions, which affect the profitability of the operation. However, gross errors, due to a variety of reasons like faulty sensors, bad instrument calibration, or incorrect process models may corrupt the actionable information supplied to operations, quality managers, and maintenance personnel. The solution is to use the sophisticated new tools to model the process, sift through the available data to locate the gross errors, and use statistical data reconciliation to validate the sensors and instruments. In this way the data are unified to give the most accurate plant information for use by the monitoring and decision making processes. Most mining and metallurgical plants use predictive maintenance policies based on statistical analysis and special techniques, like vibration analysis, and oil and lube analysis for critical equipment. Process control strategies are installed in several metallurgical sites. All of these depend on reliable and accurate data. The data unification methods validate the individual measurements by using the concept of balances and statistical techniques where each instrument is no longer independent of the other measurements in the facility. This paper refers to the data unification and analysis methods required for profitable plant operations. Continuous improvement and monitoring of the measurement system at the plant and analysis of the reconciled data provide the best information for the decision-making process. On-line gross error detection and elimination methods are required to ensure efficient evaluation of process performance and process optimization. An open discussion of the new methods for gross error detection and data unification will be presented.

May 1, 2001

By R. P. D. Graham

It is almost exactly two hundred years since the foundations of the mining and metallurgical industries in Canada were laid. There '."'as nothing spectacular about this early start. It had to do with the most basic phases of these industries-the mining of coal and iron ore, and the manufacture of cast and wrought iron. At several points along the coast of Cape Breton island, coal seams may be seen outcropping quite conspicuously, and it is probable that they had been observed, and possibly worked in a small way, in very early times. However that may be, these coal seams have the distinction of being the first in North America of which there is any printed record, reference to them appearing in a volume by Nicolas Denys which was published in Paris in 1672. Regular coal mining in the district did not commence until about fifty years later, however. The metallurgists started their operations along the north shore of the St. Lawrence river. Here, at many points between Montreal and Quebec, are to be found deposits of bog iron ore, and in 1 730 a furnace for smelting such ore was established on the St. Maurice river. The St. Maurice forges continued in operation until 1880, and throughout that long period they were famed for the fine quality of castings produced, and also for a-superior wrought iron.

Jan 1, 1924

By P. Srinivasan

Corrosion is a major operational problem in amine-treating plants causing significant expenditures each year, Corrosion may become more severe when the amine plants contain process contaminants ? namely heat-stable salts. The heat-stable salts enter the plants with feed-gas streams and makeup-solution, and/or are produced within the plants by reactions of alkanolamine and available carboxylic-acid anions, This work investigated interaction corrosion effects that may exist in amine-treating plants containing a mixture of heat-stable salts, The investigation was experimentally carried out in a 5 kmol/m3 monoethanolamine (MEA) solution containing 0,20 mol/mol carbon dioxide (CO2) loading at 80°C under atmospheric pressure using carbon steel 1018, Six heat-stable salts, including formate, oxalate, bicine, acetate, thiosulfate and chloride, were tested with a series of salt combinations, Potentiodynamic Polarization, Tafel Extrapolation, and Cyclic Polarization were used for revealing corrosion behavior, determining corrosion rate, and examining the pitting tendency, respectively, Results show that thiosulfate induces the most corrosive environment when present either individually or in the form of salt mixtures.

Jan 1, 2005

By Ken Hester, Bruce Arthur

"Introduction""Pebble milling"" is a term used to describe secondary grinding done with rock pebbles rather than steel balls or other steel or metal shapes. This paper discusses pebble milling with particular attention being paid to uranium grinding circuits.Pebble milling is typically employed:a. where the cost of steel balls becomes exorbitant, as may be the case in an isolated area.b. where the extra steel added from steel ball consumption may be detrimental to further processing.c. where the over-all economics favour the use of pebbles rather than ball.Pebble milling differs from autogenous and semi-autogenous grinding in that a sized product has been removed from some part of the primary comminution circuit, and it is this sized product which is added as grinding media to the pebble milling stage. The pebbles do not necessarily have to be produced from the ore- ""foreign"" pebbles can be used. Also, pebble milling generally refers to grinding from a fine size, below about 6 mesh (3360 micron), with relatively small media, that is, secondary grinding. In South Africa, however, primary pebble mills are sometimes used to grind crusher house product, and thus function in place of rod mills. Pebbles for this service are large and heavy as they must weigh as much as balls used in similar service.The first large applications of pebble milling were in South Africa(n. ""Tube milling"" with pebbles started in 1904. The tube mill was simply a tumbling mill with a length to diameter ratio over two. A ""typical"" early tube mill was 5.5 ft. (1.7 m) in diameter and 16 ft. (4.9 m) in length. Diameters increased steadily. King(n mentions 8-ft. (2.4 m) units in his 1949 book. By 1961, the largest units discussed by Jackson('' were 12ft. (3. 7 m) in diameter."

Jan 1, 1989

By Liu Yulin, Zhao Yi, Tan Qi, Liu Lei

"Hydrotalcite is one kind of layered double hydroxides, and has special crystal chemical characteristics. Due to its good thermal stability, hydrotalcite used as the PVC heat stablier has attracted scientists’ attention. In this study, nano-hydrotalcite was synthesized by the method of mechanochemistry/crystallization, using brucite, Al(OH)3 and Na2CO3 as raw materials, and added into PVC to investigate the effect of hydrotalcite on thermal stability of composites. The synthesis mechanism was suggested by virtue of XRD, FE-SEM, FT-IR. It has been indicated that at the first of dry milling process, the parical sizes of brucite and Al(OH)3 decrease, while specific surface areas of them increase by the action of mechanical force, until produced amorphous particles. In the process of wet milling, metal ions in the amorphous body, which has high surface energy, can easily react with H2O, and produce the precursor of Mg6Al2(OH)18•4.5H2O, which has the same crystal structure as hydrotalcite. Under the hydrothermal condition, anions of OH- in the interlamination of precursor are exchanged by CO32- in the solution and nano-hydrotalcite is generated at last. The thermal stability was characterized by Congo red method. The results have revealed that hydrotalcite is one kind of long-term heat stabilizer, and residual stability time increase with the rise of added hydrotalcite amounts.INTRODUCTIONHydrotalcite, one kind of anionic clays, has been attracted a great interest for researchers because of their unexpected physical and chemical properties. The general formula is Mg6Al2(OH)16CO3·4H2O, where Mg2+ and Al3+ occupy octahedral positions in the brucite-like layers, and CO32- is an interlayer anion (Hoyo, 2007). Hydrotalcite is widely used in the fields of chemical engineering, materials engineering, environmental protection, medicine, and so forth, owing to its unique capability of adsorbability, ion exchange and thermal stability (Rozov, Berner, & Taviot-Gueho, 2010; Iwasaki, Yoshii, & Nakamura, 2012; Ay, Zümreoglu-Karan, & Temel, 2011; Cavani, Trifiro, & Vaccari, 1991; Li & Duan, 2005; Lin, Wang, & Evans, 2006). As a result, the study on synthesis and application of hydrotalcite has received considerable attentions."

Jan 1, 2016

By A. Lloyd, Montgomery, J. Jorgesen, W. J.

"Coals are ranked according to their degree of metamorphism or progressive change in the natural series from lignite to anthracite. The reader is referred to ASTM Standard D-388, ""Standard Classification of Coals by Rank"" for a detailed description of the system in use throughout North America including Canada.Fixed carbon and calorific value (expressed in Btu/ lb) calculated to the mineral-matter-free basis have been chosen as the main characteristics from which rank is established. Higher rank coals are classified according to fixed carbon content, lower rank coals according to the calorific value on a ""moist"" mineral-matter-free basis. Certain adjacent groups are differentiated according to their agglomerating (caking) properties. ""Moist"" refers to inherent moisture. Referring to Table 1, coals having calorific values greater than 14,000 Btu/lb on a moist mineral-matter-free basis and fixed carbon of 69% or more on a dry mineral-matter-free basis are classified according to fixed carbon. Coals having calorific values of less than 14,000 Btu/lb on a moist mineralmatter-free basis are classified according to calorific value on a moist mineral-matter-free basis. Agglomerating coals having 69 to 86% fixed carbon on the dry mineral-matter-free basis are classified in the low or medium volatile group of the bituminous class according to their volatile matter content. Agglomerating coals having calorific values between 10,500 and 11,500 Btu/lb are classified in the high volatile C bituminous coal group; nonagglomerating coals in the same calorific value range are classified in the sub-bituminous A coal group."

Jan 1, 1985

By G. Shore

Radiation grafted structures my be fabricated to contain ion exchange groups selective to an ion complex. Proper choice of substrate and monomer will provide selective ion exchange with differing physico and chemical properties. Grafting a selected monomer to the proper polymer will provide selective ion exchange with assured chemical protection of the substrate. Ion exchange systems utilizing radiation grafted structures have been fabricated to ''capture'' gold, silver and palladium from dilute solutions. Other ion exchange systems can feasibly be produced to remove other precious metals. Rotating Cathode Technology is used to recover the metals from their regenerating solutions are pure metal foil.

Jan 1, 1985

By J. A. Brown, F. P. Kerr, M. A. Archer

Extensive testwork on Global Atomic’s Dasa Project in Niger has been conducted at SGS Minerals laboratory in Lakefield, Ontario. Much of this testwork has focused on a two-stage counter-current leach as a means of improving leach efficiency and decreasing reagent consumption. The ore contains uranium mineralization requiring relatively high sulphuric acid concentrations during leaching to achieve acceptably high extractions. Excess free acidity in the leach solution may be utilized by recycling the high acid solution and contacting it with fresh ground ore. The resulting pregnant leach solution (PLS), now higher in uranium concentration and depleted in free acid, is forwarded on to uranium recovery by solvent extraction. The first stage residue proceeds to the second stage leach where fresh acid and oxidant are provided to leach the remaining uranium. This paper presents the results of the testwork conducted on both a Master Composite and Variability samples.

Jan 1, 2020

By K. Thuro, H. Käsling, F. Menschik

"With increasing data volume, due to enhancing requirements for ground investigation programs for large construction projects, the demand for more efficient filing systems is more and more growing. Depending on the project we also have to use flexible systems to cope with varying data out of different lab and field tests.The chair for Engineering Geology at TUM is developing a web-based database solution to handle all project relevant data in a more appropriate way. We aim to optimize our data management to achieve a fast and easy way of collecting, documenting and analyzing our gained data. The second objective is to provide an easy access to our data for project partners across broadly distributed locations.This Database system consists of a PHP web interface and a MySQL database core. The current setup allows an online access via Internet (www). We are able to grant and constrain access to all data or only arrays of data with our user management system to guarantee the safety of project data and respect all rights and proprietorship. The database system is of modular design and consists of the following three base modules: module of general project data, module of laboratory data and user management module. At the current stage we are able to save and work with all usually generated specific values from unconfined compressive strength tests, brazilian tensile strength tests, point load tests, CERCHAR and LCPC abrasivity tests and ultrasonic tests. The user is able to perform a simple statistical analysis within our database (e.g. average calculation of one sample) and export data as csv or xls files for further analysis.For specific questions within projects we are able to deploy and integrate further modules in our database system. At this moment, we are developing an add on to use this database for different drill test analyses. One of the tools correlates drilling performance and drill head wear measured in the field with rock mechanical properties, and extrapolates the data to estimate the performance and wear in new projects. Today we are managing 90 projects with 550 samples and almost 1350 lab tests with the base module.In our contribution we aim to demonstrate an efficient way of data structuring using a relational database for laboratory and field testing data."

Jan 1, 2015

By Jeffrey D. Oke

While significant progress in underground construction engineering has occurred in the past few decades, a number of fundamental deficiencies persist regarding the recognition, prediction, and mitigation of underground construction hazards associated with complex geological conditions in rock and soil works, such as tunnelling. Many of these shortcomings could be addressed by improving geomechanical models which, in turn, would provide more realistic frameworks for determining input parameters for design analysis. This would improve predictions of construction efficiency for tunnelling and the formulation of more accurate modelling techniques (2D, 3D and 4D) required to optimize the design of engineered rock structures. This research focuses primarily on the issues related to forepole temporary tunnel support within weak rock masses. This research attempts to determine how best to numerically model forepole support. The behaviour and mechanics of forepole support has not been quantified and/or optimized. As well, there is a lack of in-situ and/or laboratory forepole and weak rockmass interaction parameters available. In terms of numerical modelling, there is a lack of understanding of the use of proper interaction parameters associated with the forepole and the rockmass. The parametric study that has been conducted by the authors demonstrates the influence of each of the forepole-rockmass interaction parameters and their sensitivity. Introduction

Jun 1, 2012

By E. P. Wiechmann, J. A. Henríquez, P. E. Aqueveque, L. G. Muñoz, G. A. Vidal

"The original segmented intercell Optibar succeeded in reducing the magnitude and occurrence of short circuits. It also improved the specific energy consumption of the process. This paper expands the load current source concept introducing a triple segmented bar. This new bar adds immunity to dirt contacts and open circuits. Moreover, it further improves the standard deviation of current densities. As compared with industrial practices this development should accomplish an 8% specific energy reduction. Also, a plant implemented with BBS should be able to work with 12.5% higher process currents than Walker without compromising the operation.INTRODUCTIONIn 2011 the technology based on current mode was implemented at industrial scale. The success of this technology moved CIM Magazine (Lanktree, 2011) to write in the Jan 2012 issue an upfront story of this technological innovation. To cover the story, the technical reporter Graham Langtree was appointed by Peter Braul Editor of the upfront section. The article tells that “More than 40,000 tonnes of copper have been refined in a year-long test run of Optibar Inc.’s new technology at Barrick Gold’s Zaldívar copper plant in northern Chile. The new segmented intercell bars being used in the Compañía Minera Zaldívar refinery have slashed energy costs, reduced short circuits during refining and allowed the production of heftier, purer sheets of copper – gains that all promise to boost the plant’s margins. A copper refining tank house containing the cell circuits typically consumes 2,000 kWh of electricity to produce a single tonne of grade-A copper. Yet, monitoring the energy efficiency of the Optibar technology after increasing the weight of harvested copper sheets, the project’s engineers recorded a 92 kWh-per-tonne cut in energy consumption, a savings of 4.6 per cent. “Today, with the power prices we have, Optibar technology represents a potential savings for the whole plant of US$1.5 million per year,” says Robert Mayne- Nicholls, executive general manager of Barrick Gold’s Chilean operations.”"

Jan 1, 2012