Search Documents

By M. B. Shongwe, R. K. K. Mbaya, C. K. Thubakgale, P. Mendonidis

"A low-grade nickel-bearing ore was pre-concentrated on a SB40 laboratory model Falcon Concentrator. Three size fractions, -212+125, -125+75 and -75 µm were tested with the intent to upgrade the nickel content by reducing their content of fine silica, which becomes amorphous during leaching. Separation of silica from nickel-bearing magnesium silicate minerals; hornblende, clinochlore and talc, was more efficient in the finer particle sizes, -125+75 and -75 µm, and at high G-forces. For these two size fractions, nickel was upgraded from 0.06 to 0.07%, with a reduction in silica content from 52.12 to 50.71%. Leaching of feed samples prior to pre-concentration resulted in the formation of amorphous silica, indicative of the presence of fine silica in the samples. Leaching of nickel from the -125+75 µm fraction increased with increasing G-force and feed pulp percent solids, while that of -75 µm was not influenced. The optimum nickel recovery was 15.68% to the Falcon underflow, using the feed size fraction of -75 µm, 30 G and a feed pulp solids content of 10% solids, after 120 minutes of treatment.INTRODUCTION A low-grade South African nickel-bearing ore with about 0.06% Ni was previously studied for atmospheric pressure acid leaching using sulphuric acid. The study was motivated by the continuing search for methods to treat of low-grade ores, which appear to be an increasingly important source of valuable metals as a result of a declining production from rich sulphide ores. Nickel is a base metal that is used as an alloy in steelmaking and chemical industries because of its resistance to corrosion (Haudet et al., 2015). Nickel laterite ores with grades lower than 1.50% Ni are considered to be complex ores, accounting for 70% of the global nickel reserves (MacCarthy et al., 2016). Their complex nature may be attributed to the indefinite mineralogy of these ores, in which nickel may occur in more than one mineral host. In some cases, nickel may be finely disseminated in the ore. The grade of such an ore and complex mineralogy do not justify the application of pyrometallurgical methods for extraction of nickel (Zhu et al., 2012). This suggests that there is a need for less expensive alternative methods of extraction. This study investigates the application of centrifugal gravity concentration, using the Falcon concentrator, followed by leaching to determine the effect of pre-concentration of the ore prior to extraction by atmospheric pressure leaching with sulphuric acid."

Jan 1, 2017

By W. A. Lang

RESEARCH has been defined as the link between the present and the future. Science, wonderful though its achievements may be, has but scratched the surface of the unknown. Research is directing its attention to winning new facts in order that their application to the processes of today may open up new sources of wealth for the common benefit. Two classes of research investigations are often recognized-fundamental and applied, but these classes merge into each other and it is often hard to distinguish one from the other. Fundamental research is carried out primarily to develop basic facts, but frequently these are found to have immediate economic value, while applied research, specifically aimed at economic values, often necessitates a preliminary fundamental investigation. Both are essential and both should proceed by scientific method. It is obvious in fuel technology that a knowledge of the physical and chemical constitution of the various coals is fundamental to their industrial utilization, and further, a knowledge of the way these coals react under different conditions of temperature, atmosphere, etc., is necessary in solving such problems as storage, combustion, carbonization, gasification, or con-version to liquid fuels. The wide range of coals, the complexity, of their constitution, and the many uses for coal, makes fuel research no simple subject but one with unending possibilities. The Research Council of Alberta, formerly known as the Scientific and Industrial Research Council of Alberta, was established in 1919, to promote the development and conservation of the natural resources of the Province. The work of the Council was arranged in six major divisions: Fuels; Geology; Road Materials; Soils; Natural Gas; and Forest Products. The office and laboratories are located in the University of Alberta. The Council was financed until the depression of 1933 by a separate vote of the Legislature, but since then has been continued, though on a much smaller scale, as one of the activities of the University. It might, however, be noted that although the Council is now in abeyance, a skeleton organization has been maintained so that it can be brought back to active service as soon as conditions warrant. Annual reports are still submitted to the Legislature. Funds have not been made available, however, for the publication of the last five reports.

Jan 1, 1942

By A. G. Doll

The Bond low energy impact (crushing) work index test is specified to be performed on rock specimens between 50 mm and 75 mm in effective diameter. NQ-diameter drill core, frequently used in mineral exploration programs does not meet that specification, it being 45 mm diameter or less. This paper reports the effect of performing the impact test on contiguous sections of HQ diameter and NQ diameter core, exploring the hypothesis that the contiguous intervals give equivalent results in spite of the core diameter difference.

Jan 1, 2012

By M. Kozlowski, I. Candy, S. Kashani-Nejad

The production of ferronickel and matte from nickel laterite ores is dominated by the Rotary Kiln, Electric Furnace (RKEF) process. Over time, major improvements have been made to kiln operation. In particular, kilns are now required to perform substantial amounts of reduction of the metallic oxides, thereby reducing the load on the electric furnace and substituting less expensive fossil fuel for electrical energy. To the basic refractory lined cylinder have been added: internal features such as dams and lifters, aimed at changing residence times in different sections of the kiln and enhancing gas/solids interaction, on-board fans to introduce tertiary air and on-board scoop mechanisms to allow reductant coal additions to be made at advantageous locations along the kiln. Many of these advances in design have been made on a trial and error basis and by 'borrowing' technology from related kiln processes, supplemented by proprietary modeling to various levels of sophistication. This paper presents a conceptual review of modeling components for the development of a computational model for granular material flow, combustion and heat and mass transfer in a nickel laterite kiln. These components include: granular material flow and segregation models for the simulation of bed motion, heat transfer models that simulate heat transfer by turbulent diffusion and radiation and the distribution of this thermal energy within the bed, and fluid flow models for the prediction of combustion aerodynamics.

Jan 1, 2005

By I. A. Menshikh, S. A. Kotov, N. L. Shinkarkin

All the cycle for conversion of natural and reprocessed uranium of ROSATOM’s “TVEL” Fuel Company is concentrated at the Siberian Chemical Plant. Conversion capacities are located on two sites, i.e. the Radiochemical Plant, which refines feedstock, and the Conversion Plant, which produces uranium oxides and uranium hexafluoride. Liquid radioactive waste arising in the process, after pretreatment, is transferred to a dedicated national operator for underground disposal. Environmental strategies pursued by the Fuel Company involve the introduction of process solutions intended to eliminate liquid radioactive waste and convert it into a solid phase. In the 5–7 years coming, work will be performed to refurbish and upgrade conversion facilities of the Siberian Chemical Plant that will principally change its radioactive waste management scheme. This paper describes the current waste management scheme and sets out planned schemes for management of natural and reprocessed uranium waste, which will be implemented in the refurbishment of conversion facilities of the Siberian Chemical Plant. The new technologies for the management of liquid radioactive waste from uranium conversion described in the present paper have an undeniable advantage over the current technology mainly due to significantly less environmental harm.

Jan 1, 2020

By C. H. B. Leitch, T. N. MacAuley, R. L. Linnen, A. E. Williams-Jones

"The Trout Lake stockwork molybdenum deposit is temporally and spatially related to the emplacement of a late Cretaceous granodiorite-tonalite stock in southeastern British Columbia and contains an estimated 49 million tonnes grading O.I9% MoS2- No metal zonation patterns are apparent, with the exception of peripheral tungsten skarn, and exploration was guided largely by geological interpretation. It is typical of the granodiorite, or fluorine-poor type of molybdenum deposit. Molybdenite is contained within a quartz-feldspar vein stockwork and coeval dissemination in igneous (and less commonly metasedimentary) hosts. In general, molybdenite is strongly associated with alkali feldspars, but in detail it is intimately associated with incipient muscovite replacement of albite and K-feldspar; veins that lack feldspars are also typically barren of molybdenite. These textures suggest that fe/dspathic alteration (and precipitation in veins) was an important precursor to mineralization, and the occurrence of similar textures elsewhere (e.g. Henderson) suggest that early feldspathic alteration is important to the genesis of molybdenum deposits in general. Molybdenite deposition at Trout Lake was preceded by contact metamorphism, skarn and potassic alteration, and was overprinted by muscovite-ankerite (phyllic) alteration. Only moderate temperature changes are recorded by the metamorphic and alteration mineral assemblages (350°C to 450°C}; however, with time, fluids became increasingly more acidic and enriched in C02- In light of the intimate molybdenitemuscovite intergrowths, the decrease of pH probably exerted a major control on mineralization.IntroductionGranite-hosted molybdenum deposits can be classified in terms of the composition of the related intrusion, e.g., the granodiorite and granite types of Mutschler et a!. (1981), or the calc-alkaline, alkali-calcic, and alkalic types of Westra and Keith (1981). They have also been classified on the basis of their fluorine contents (Theodore and Menzie, 1984) with the fluorine-rich and -poor varieties roughly corresponding to granite- and granodiorite-type deposits, respectively. For economic reasons, most exploration and research has concentrated on the high-grade/large tonnage granite-type of deposit, exemplified by Climax. F1uorine-poor, granodiorite-type deposits are, however, the most common type in Canada and have been mined in the past (e.g., Endako). In this paper, the authors summarize the research that has been carried out on the fluorinepoor Trout Lake deposit (Boyle and Leitch, 1983; Linnen, 1985; Linnen and Williams-Jones, 1987; 1990) and use what has been learned to develop guidelines for the future exploration of fluorinepoor, granodiorite-type molybdenum deposits."

Jan 1, 1995

By M. F. Goudge

BRUCITE associated with highly metamorphosed Precambrian limestone was discovered in the vicinity of Rutherglen in northern Ontario by the writer during field work on the limestones of that district in 1937, and later was identified in similar limestone at Bryson and Wakefield, Quebec. The brucite occurs as granules disseminated through the limestone (Figure 1) and comprises from 20 to 35 per cent of the rock. Such rocks may be referred to as predazzites or pencatites, depending on the proportions of the constituent minerals. In this paper, however, the general term brucitic limestone is used to designate limestone containing brucite. In none of the deposits does the magnesia content of the rock approach that of magnesite, and in the deposits near Bryson and Wakefield the magnesia content is only that of dolomite. Therefore, without some method of concentrating the brucite, the deposits would be of little or no more value as a source of magnesia than is ordinary pure dolomite, which is abundant in many parts of Canada. Investigations in the laboratories of the Bureau of Mines have, however, resulted in the development of a method whereby, from certain of the deposits, pure calcined brucite, or magnesia, in granular form can be obtained, apparently at a cost that will enable it to compete in eastern Canada with imported magnesia. The granular magnesia so obtained appears to be highly suitable for use in basic refractories, for making magnesium metal, and for various other purposes for which magnesia is commonly used. Prospecting in the neighbourhoods of the original discoveries has resulted in a number of other deposits being found in each of the three areas, and there is now apparently available s1.dficient brucitic limestone of a grade that will lend itself to commercial exploitation to supply for many years a large part of the present and prospective Canadian market for magnesia and its products. Furthermore, it is expected that additional deposits will be discovered as prospectors and others become more familiar with the appearance of brucitic limestone.

Jan 1, 1940

By A. P. Paiva

The solvent extraction properties exhibited by some /V,N'-tetrasubstituted malonamides to efficiently and selectively recover iron(III) from concentrated chloride leaching solutions can be found in the recent literature. The iron(III) extractive chemistry exhibited by some of these derivatives is revisited, in order to compare their chemistry with that shown by a few of the new malonamide compounds. The generally good extraction efficiency towards Fe(III), from >4 M hydrochloric acid solutions, and the relative ease of Fe(III) stripping by distilled water are remarkable findings that are confirmed for the malonamide derivatives described in this work. Furthermore, additional data regarding their selectivity towards Fe(III) extraction over several base metal ions and their behavior when subjected to successive Fe(III) extraction-stripping tests are also presented and discussed.

Jan 1, 2006

By K. A. Clark

"The repacked mineral aggregates of good grade oil sands have permeabilities ranging between 15 darcys to 350 millidarcys. The variation is due to the silt contents of the aggregates. Few good grade oil sands contain as much as 30 per cent •silt, most of them contain less than 20 per cent, and a large proportion have less than 10 per cent.The permeabilities of repacked good grade oil sands (oil included) depend on the degree of liquid saturation. When saturation with oil plus water reaches between 80-90 per cent, permeability is reduced to zero. As total saturation decreases below 80 per cent, permeability increases ranidly. Permeabilities of between one and two darcys were observed for total saturations between 60-70 per cent.The mean value for 18 measurements of the permeabilities of ""undisturbed"" core samples of good grade oil sands was 50 millidarcys. This value is •probably too high. The mean value for 20 measurements on core samples of interbedded oil sand and shale was 100 millidarcys. The mean value for 11 measurements on shale was 10 millidarcys."

Jan 1, 1960

By M. J. S. Innes

Abstract This paper is an account of an investigation made by the Dominion Observatory with a gravity meter and magnetometer over sulphide concentrations at East Sullivan, Val d'Or, Que., in June, 1947. The topographic relief over the area does not exceed 20 feet. The overburden varies from 0 co 50 feet. The west orebody had been outlined by extensive drilling. The average density contrast between the sulphide body and surrounding rocks is 0.5. Two hundred and sixty gravity and one hundred and ninety magnetic stations were observed. The results are shown on contour sketches. A derailed account is given of the methods employed to reduce the gravity observations. The survey shows that both gravimetric and magnetic methods are useful in delineating sulphide deposits under the conditions in which they occur at East Sullivan. The results indicate that the buried contact of the syenite intrusive southeast of the orebody could be traced with the gravimeter and chat the magnetometer was of little value for that purpose. Gravity anomalies due to the varying depths of overburden are negligible as compared to the magnitude of the total anomalies. Introduction The project was first suggested at a meeting of the Associate Committee on Geophysics of the National Research Council in September, 1946. At that time it was pointed out that the accuracy and speed of operation of the new gravity meters made them of special importance for geophysical prospecting and it was highly desirable to have an objective test of the performance of an instrument of this kind in delineating an orebody of known dimensions and density characteristics. Several years ago, a private company did some work with a gravimeter over the Amulet deposits, near Noranda. Unfortunately, the topography there is rather rugged, with hills and ravines exceeding 100 feet, so that the topographical effects rendered it impracticable to distinguish between anomalies due to the sulphides and those due to surface irregularities. An orebody of a typical nature, where the disturbing topographical corrections were not excessive, was therefore sought.

Jan 1, 1949

By A. G. Doll

"This paper expands the SAG mill survey database published by the Author at Procemin 2013. The new database includes 49 published SAG/AG mill surveys and includes mills from all over the world. The paper will compare the survey database to SAG mill models by Austin, Morrell and Hogg & Fuerstenau with the purpose of demonstrating the degree of fit of the models to surveys and validating any empirical “fitting factors” used in the models.SAG mill power draw models are used in mill design and grinding circuit modelling to predict how much power will be consumed by a particular mill geometry and operating configuration. The importance of conducting surveys suited to model calibration will be highlighted because the review of literature shows that survey information important to modelling is often missing or omitted. A recommendation for the collection of data during a mill survey is presented, along with some assumptions used by the Author in the absence of certain data. The benefit to mining companies of publishing their survey data, and thereby allowing modellers to improve their model calibration, is discussed.The comparison of models requires a discussion of the measurement of power in a mill drive system as the models use slightly different position in the electrical network for ""where power is measured"". The benchmarking of models against plant operations requires a similar discussion of power measurement."

Jan 1, 2016

By L. C. S. Dharmasiri, S. M. Shin, A. Senaputra, J. S. Sohn, K. H. Park, J. Avraamides

Reducing agents can be applied to leach metal values from natural and secondary resources such as laterite ores and deep sea manganese nodules and recycled materials such as spent batteries / catalysts which contain high-valent metal oxides of manganese, cobalt and iron. Selective leaching of some metals can be achieved by selecting conditions to control the saturated solubility and dissolution rates of metals from oxides or mixed metal/oxide matrices. The leaching results are rationalized on the basis of chemical species, Eh-pH diagrams and heterogeneous kinetic models. The role of reducing agents such as hydrogen peroxide, sulfur dioxide and iron(II) sulphate, in acid, alkali and in the presence of complexing ligands such as ammonia for the improvement of the leaching of metal oxides and metals is discussed. Previous studies on acid leaching of metals from nickel laterites, manganese nodules and spent catalysts/batteries in the absence or presence of reducing agents show that the rate controlling step involves the diffusion of protons through a thickening product layer on the particle being leached. It is shown that the leaching of nickel and cobalt from manganese nodules and zinc-carbon batteries in ammoniacal sulphur dioxide solutions also obey shrinking core kinetics.

Jan 1, 2014

By Arthur Notman

Since addressing the Institute a year ago on The Future of the Copper Industry (l), many things have happened, most of them bad. It has been a hard year for profits and prophets. It was, therefore, with consider-able perturbation that I accepted the gracious invitation of your Committee to reappear. On reviewing my remarks of a year ago, I. have wondered whether, under pressure of more important matters, the Committee had neglected to make a note of them, or whether they felt that further explanations from me were in order. In either event, I am glad that I am here and welcome the opportunity to make any contribution I can to a clearer understanding of the problems of copper to those concerned. The English-speaking nations own 80 per cent of the present world-production of the metal. Col. P. E. Barbour, Secretary of the Mining and Metallurgical Society of America, and I recently completed an estimate of the known world resources of copper. We placed the figure, in round numbers, at 100,000,000 tons of metal. Of this amount, about one-third lies in the United States, one-third in the British Empire, and one-third in South America; and all but 4 per cent of this is owned by British Empire and United States capital. Our figures do not include any estimates for Russia, Japan, or Europe, on which there are no available data. It is true, consequently, that the British Empire and the United States are the ones concerned. It seems to me to be a matter of great importance to the world at large, and of even greater importance to those nations themselves, that the known sources of supply of this metal, so essential both in peace and war, rest so strongly in their hands. I cannot believe that in the long run they will neglect their responsibilities in the wise administration of these resources.

Jan 1, 1932

By L. E. Djingheuzian

IN 1953, Lewis (1) published an article which brought forth a great amount of discussion by grinding engineers. In his contribution to discussion the present writer (2) suggested that, for the most efficient performance of a ball mill, there must be a .definite relationship between Cn, per cent critical speed, and V p, per cent mill volume occupied by the ball charge. Later, he ( 3) was able to publish some grinding data from Wright-Hargreaves milly which appeared to bear out this contention. It is with this view to establishing a fundamental relationship between Cn and Vp that the idea of this Forum was conceived. Accordingly, a questionnaire was prepared and copies of it were mailed to over eighty Canadian mill operators. This questionnaire did not include a question on dilution on the assumption that each mill operator was using the most efficient dilution for his operation, nor was a question on efficiency of classification included since it was thought that the inclusion of efficiency of dassification in the questionnaire at this preliminary stage might render the forum discussion,. while everybody was trying to find his bearings, too unwieldy. However, it is evident that, as discussions develop, this forum will have to define a uniform method for establishing most efficient classification in grinding circuits

Jan 1, 1957

By Paul Guliov

Potash dominates the industrial mineral scene in Saskatchewan accounting for 44% of total provincial mineral production in 1981. More than 7 million tonnes of potash have been produced annualy in recent years; ten underground mines are presently (1983) active. Sodium sulphate and cement are also important mineral products. Construction aggregates, clay products, bentonite, salt, peat moss and sulphur complete the list of industrial mineral products.

Jan 1, 1984

By E. Uzun

"In this study, H2SO4 and HCl leaching behaviour of an ore sample containing 1.87% of Ni, obtained from the Karaçam (Eskisehir-Turkey) lateritic deposit that started operation recently was investigated. Acid concentration, temperature and reaction time were investigated as variables by comparative leaching tests and the optimum leaching conditions were selected on teh basis of Ni, Fe, Co and Mg behaviour. For H2SO4 leaching, optimum leach parameters were 95°C, a 12 normal H2SO4 concentration and 90 minutes of reaction time, and under these conditions Ni and Fe dissolutions were 97.6% and 95.4% respectively. On the other hand, 70°C, an 8 normal HCl concentration and a reaction time of 90 minutes were found to be the optimum parameters for HCl leaching, and Ni and Fe dissolutions found were 97.1% and 97.8%, respectively.INTRODUCTION Today, nickel and various nickel compounds are obtained from sulphide and lateritic nickel ores (Moskalyk & Alfantazi, 2002). Even though about 72% of the world's nickel reserves constitute lateritic ores, only about 42% of nickel is produced from these ores. The decrease in production from sulphide deposits, on the other hand, and increases in the use of nickel in the iron and steel, and battery production sectors, and especially the production of nickel cast irons in recent years, have accelerated the importance of making use of lateritic deposits (Luo et. al., 2010; Chang et. al., 2010). In the beneficiation of sulphide nickel ores, mostly pyrometallurgical methods are used. On the other hand, about 39% of lateritic ores are beneficiated by pyrometallurgical, and 61% are beneficiated by hydrometallurgical methods (USGS, 2009). In laterite beneficiation, the ore properties are of significance; that is to say, limonitic ores are eneficiated by high pressure acid leaching or via the Caron process, nontronitic ores are beneficiated by high pressure acid leaching or heat treatment (smelting), and ores containing serpentine by pyrometallurgical methods (Berezowsky, 2004; McDonald & Whittington, 2008a; Dreisinger et. al., 2015)."

Jan 1, 2017

By J. Baz-Dresch

"The most cost-effective method of placement of the high strength fill used in the Cannon Mine' s overhand cut-and-f ill bench stopes was determined to be truck haulage. Constraint s imposed by the mine layout dictated the use of a truck which could dump its load in a fifteen-foot high drift. The Dux Teledumper truck was selected as the most suitable unit for this application based upon operational and maintenance parameters which included a telescoping, tilting dump box; large load capacity; and robust construction. Development of the truck continues through the cooperation between the manufacturer and user. INTRODUCTIONThe Cannon Mine is situated in the centre of Washington state, approximately midway between the cities of Spokane on the east and Seattle on the west. The mine complex is located three block s south of the Wenatchee city limits at the eastern base of the Cascade Mountain range.Asam era Minerals (U.S.) Inc., with 5I% ownership, operates the Cannon Mine. Breakwater Resources, Ltd. holds the remaining 49%.Annual paroduction is 520 000 tons per year, presently on a 21-shift per week operating schedule for both the mine and the mill.All production is presently won by overhand bench stoping with backfill. Stoping starts with 15-ft high by 24- or 30-ft wide sill cuts driven above and below a stope block . A drop rai se and slot are used to open a bench which is then slabbed toward the open slot. Truck-placed backfill is dumped into the mined - out stope from the upper sill cut. This stoping sequence is repeated until the top of the ore block is reached . The top sill cut is then tightly filled with backfill to minimize subsidence and to provide adequate roof support during extraction of the pillars.Mining equipment consists of hydraulic drills and rubber-tired, diesel scoops and trucks."

Jan 1, 1989

By Arnfinn Prugger

"The construction of the new Scissors Creek shaft at the Rocanville mine, the first potash shaft successfully completed in Saskatchewan Canada since 1979, is summarized here. Located 15km from the existing Rocanville surface plant, this new 6 m inside-diameter, 1121 m deep service shaft was built for fresh-air ventilation and access. Shaft construction in the Saskatchewan sedimentary basin involves sinking through five different rock-types: glacial tills, shales, sandstones, carbonates and salts. The first four rock- types are all water-bearing, and the salts will dissolve in water. This results in five different sinking challenges and requires five different shaft lining designs. The upper 580 m of rock (the till – shale – sands sequence) was frozen before sinking, and grouting methods were used for water control through deeper carbonate levels. Challenges that were faced and overcome during shaft sinking are reviewed, and ideas that future operators working in sedimentary basin environments might consider in order to avoid these difficulties are discussed.INTRODUCTIONThe Nutrien Inc. (formerly Potash Corporation of Saskatchewan Inc. / PotashCorp) Rocanville potash mine in southeast Saskatchewan, Canada has been in continuous production since 1971. Devonian potash, formed approximately 380 Mybp, is mined in a sedimentary basin environment at approximately 1000 m depth below surface in this area of Saskatchewan. The predominant use for finished potash products is fertilizer: potash fertilizer is concentrated and nearly pure KCl (i.e. greater than 95% pure KCl). Currently 10 potash mines are in operation in Canada, all in Saskatchewan. In 2018 Saskatchewan mines produced ˜ 23 million tonnes of finished potash products, which is approximately 35% of World demand of ˜ 66 million tonnes for the year (e.g. Nutrien Inc., 2019).In November, 2007 it was announced that the Rocanville potash mine would be expanded to increase production from 3.0 Million tonnes per year (Mtpy) to approximately 6.0 Mtpy of finished potash products, requiring an increase in hoisting capability from approximately 9.0 Mtpy to over 18.0 Mtpy. The Rocanville potash mine has historically been accessed through two shafts: a production and ventilation exhaust shaft, and a service and ventilation fresh-air shaft located approximately 200 m from each other. All surface offices, processing facilities, etc. are situated near these original shafts.A very important part of the recent Rocanville expansion involved the construction of a new service shaft (6 m diameter, 1121 m deep) for fresh-air ventilation and access, approximately 15km west of the existing surface plant. Once this third shaft was completed in 2015, the historical service shaft was converted to a second exhaust and production shaft. Three shafts are now available for mine access, ventilation and ore hoisting at Rocanville. As of December 31, 2017, annual nameplate capacity for Rocanville was 6.5 million"

Jan 1, 2019

By C. M. Bartley

Fluorspar, in addition to its familiar uses as a metallurgical flux and as a source of the electrolyte for aluminum production, has become important as an essential raw material in the rapidly growing fluorine chemical industry. The unique ability of fluorine to react and form compounds with al-most all other chemicals has made it one of the important elements in modern chemistry. Research and development over the past thirty years have resulted in a current annual production of fluorine chemicals that is both technically and economically important to industry. Because many of these chemicals and products are relatively new, and most have properties that are not duplicated by other materials, the present uses are expanding rapidly and new applications are being reported continually. Fluorspar, the only immediate and practical source of fluorine, is therefore an important mineral. This fact has been recognized in major industrial areas such as the United States and Western Europe, but has received little attention in Canada.

Jan 1, 1962

By F. K. McKean

Introduction The present paper may be considered as a sequel to a paper, A Process for Cleaning Molybdenite .Concentrate, which was presented by the author at the annual meeting of the Institute last year. In that paper, a description was given of the laboratory work leading up to the adoption of a new process for treating complex molybdenite ores of the Molybdenite Corporation of Canada. A bare outline of mill performance with the new flow-sheet was included. With this writing, the purpose is to describe the highly interesting work of translating laboratory experience into mill practice, to show what changes were required in design to put the scheme on an operational basis, and to point out the gratifying improvements in mill products which resulted from the new procedure. The process has been placed in operation at the La Corne mine of the Molybdenite Corporation of Canada. This mine was operated during the war by Wartime Metals Corporation, and, earlier, by the Molybdenite Reduction Company, which installed a small plant. The property is situated on the highway from Amos to Val d'Or, Quebec. The claims held by the Company are at the boundary between La Corne and Vassan townships.

Jan 1, 1947