Search Documents

By Hamidreza Soltanzadeh

The injection of CO2 into a reservoir or aquifer can potentially result in deformation, induced fracturing and fault reactivation in the injection zone and/or the rocks that surround it. This paper reviews the data collection and geomechanical analyses performed to assess these potential hazards for the Heartland Area Redwater Project (HARP), in which CO2 sequestration is being considered in a carbonate (Leduc Formation) reef. A three-dimensional mechanical earth model (3D MEM) was developed using available geophysical log data from several wells. The geomechanical response to CO2 injection was studied using a finite element numerical model based on the 3D MEM and pore pressure distributions predicted using a reservoir simulator. The modeling results suggest that the potential for induced fracturing and fault reactivation is low and the maximum predicted ground surface heave is less than 2 cm. Sensitivity analyses conducted with a 2D geomechanical model that was extracted from the 3D model confirm that this conclusion holds true even when a reasonable measure of uncertainty in rock mechanical properties, ambient pore pressures and horizontal stress magnitudes is accounted for.

Jun 1, 2012

By G. M. Ross, J. A. Scott, C. A. Laamanen, H. Shang

"Indirect recovery and use of waste heat contained in smelter off-gas is proposed to expand regions available for year-round, on-site production of micro-algae–sourced biodiesel, a fuel that could be used in underground machinery. A dynamic model of an off-gas heat exchanger describes capture and distribution of heat into open, external, rectangular micro-algae ponds. Smelter off-gas contains sufficient energy to maintain large-scale micro-algae cultivation pond temperatures above 15°C, even with winter ambient temperatures below –15°C. Results highlight opportunities that could lie in tapping these heat resources to produce renewable biofuels on-site and sequester CO2 while leaving the industrial process unaffected.RÉSUMÉ On propose la récupération et l’utilisation indirectes de la chaleur résiduelle contenue dans les dégagements gazeux des fonderies pour développer les régions se prêtant à une production toute l’année durant et sur place de biodiesel à partir de micro-algues, carburant dont on pourrait se servir pour le matériel d’exploitation souterraine. Un modèle dynamique d’échangeur de chaleur contenue dans les dégagements gazeux décrit le captage et la distribution de la chaleur dans des bassins rectangulaires ouverts de micro-algues en extérieur. Les dégagements gazeux des fonderies contiennent suffisamment d’énergie pour maintenir les températures des grands bassins de culture de micro-algues au-delà de 15°C, même avec des températures ambiantes en hiver inférieures à –15°C. Ces résultats soulignent les possibilités que pourrait offrir l’exploitation de ces sources de chaleur pour la production de biocarburants renouvelables sur place et pour la séquestration de CO2 sans que cela n’ait d’incidence sur le procédé industriel.INTRODUCTIONMicro-algae that grow in water can efficiently convertsolar energy and carbon dioxide into biomass. This biomass can be up to 50% oils (lipids), which can be extracted and converted into biodiesel through transesterification (Demirbas, 2008). Compared to terrestrial plants that produce similar oils (e.g., jatropha, soybean, and rapeseed), micro-algae represent an order of magnitude increase in areal productivity, do not require arable land, and can be continuously harvested (Rawat, Ranjith Kumar, Mutanda, & Bux, 2013). The potential advantages through the production of biodiesel from micro-algae also include sequestration of carbon dioxide, reduced reliance on fossil fuels, and the co-production of other value-added bioproducts."

Jan 1, 2017

By T. E. Morimoto

Summary The Research Council of Alberta has made a series of tests with the cyclone washer to investigate the influence of the following operating variables: underflow apex diameter, .specific gravity of medium, pulp ratio, density distribution of the feed, and size analysis of the feed. The results obtained for all the variables studied, except size analysis of the feed, are included in this paper. The tests were made with smaller underflow apex diameters and lower specific gravity .suspensions than have been recommended by Cerchar for the sharpest separations. However, what is considered to be sufficiently good cleaning was accomplished with a suspension of 1.30 specific gravity and an underflow to overflow diameter ratio of 0.56. It was found that the sharpness of separation was not affected appreciably by variations in specific gravity of suspension or underflow apex diameter provided that the density of separation was within the normal range of washery operation. Cyclone performance was not too adversely affected by decreasing the pulp ratio. The minimum figure which gave reasonable separation was 4 to 1. The tests with various density distributions of feed revealed .that the degree of washing difficulty had no detrimental effect on the .sharpness of separation given by the cyclone. Introduction A major problem of the bituminous coal industry today is that of reducing the ash content of the finer sizes (minus 1/4-inch) of coal. This problem is particularly acute in Alberta, where, because of tectonic movement subsequent to deposition, the coals have been rendered friable, and bands of impurities have been intimately mixed with the clean material. As a consequence, most Alberta coals, as mined, contain a large proportion of fines and have a high inherent mineral-matter content. The advent of mechanized mining and stripping operations ?has further aggravated this problem.

Jan 1, 1952

By G. Begin

"The expansion undertaken at Selbaie in 1985 necessitated an adaptation and expansion of the equipment maintenance system. This paper relates briefly the stages of transformation of the maintenance administrative structures, work methods and tools. The maintenance in a mechanized mine requires an expenditure level in the order of 20% of the total operating cost of the enterprise. Thus, the maintenance organization was modified to apply more computerized planning and follow-up, and the role of preventative maintenance was further advanced.IntroductionAs far as maintenance is concerned at Selbaie, the scenario described herein is a resume of the current situation. Although positive results have been obtained, this outline is in no way a detailed account of a fail-proof maintenance system.Once zone A-I was put into production, the expansion the mine experienced in 1985 had a direct impact on the equipment maintenance system. As centralized as it was in the beginning, the system is now partially decentralized.The over-all changes to the maintenance department demonstrate the flexibility required by organizations in new situations. In spite of the exceptional results obtained before the expansion, it became evident that both the maintenance and production sectors would have to be combined. In doing so, a more appropriate coordination of maintenance work could be obtained and the maintenance staff would obtain a more detailed knowledge of the equipment in each sector. In addition, by keeping the general and specialized departments centralized, it was possible to offset the negative effect s of a decentralized system, namely too much manpower."

Jan 1, 1990

By J. Roth

"While not taking issue with the general thesis expressed in Dr. Ridge's analysis of the role of genetic concepts versus observational data in ore exploration (Ridge, 1983), the criticism could be offered that the author tends to slight the importance of conceptual (i.e. theoretical) models in mineral exploration.As a general rule, observational data in science lacks significance and utility without a theoretical construct to organize those observations. Theory in turn dictates what observations are made-and which ones are judged important. Thus, for example, prior to the elaboration-and acceptance- of the current model for volcanogenic base metal deposits, the structural aspect s of these deposits were most closely observed and studied by explorationists. The nature of the enclosing rocks and any attendant alteration was given minimal attention, and certainly didn't figure prominently as an exploration guide.Similarly, the importance of alteration features to exploration for porphyry copper-molybdenum deposits was only perceived when a theoretical model was developed to account for these aspects. Indeed, many of these porphyry copper deposits were regarded as epigenetic vein deposits by geologists of an earlier era observing and examining on a different physical scale-and with a different theoretical bias.In constructing and evaluating such conceptual models, explorationists primarily rely on observation data and proximate associations; speculative thoughts as to ultimate provenance or crustal evolution clearly play a subordinate role, as Dr. Ridge argues. This, however, should not obscure the fact that concepts and theories do indeed exert a major influence in mineral exploration."

Jan 1, 1983

By W. S. Hargratt

THE present era of exploitation of the Little Long Lac and Sturgeon River areas commenced in 1925, when Beardmore Gold Mines started development of what is now the property of Northern Empire Mines. A shaft was sunk in 1927-28 and a very limited amount of underground work was carried out, following which the property was shut down. It remained idle until 1932, when Empire Star Mines, a Delaware Company, optioned the property. This Company formed the Northern Empire Mines Company, Limited, to operate the mine, and immediately instigated an aggressive programme of surface and underground development. By the summer of 1933, sufficient ore was indicated to justify the installation of a small mill. The decision was also reached to bring in electric power. A power-line was built from Hydro, the Ontario Power Commission's development on the Nipigon river, to the mine, a distance of approximately 50 miles. This work was entirely financed by Northern Empire Mines. Mill construction was commenced in October, 1933, and completed by March, 1934, thus making this mine the first producer in this district.

Jan 1, 1940

By T. Hidayat

The distributions of minor elements between slag/metal and slag/matte in equilibrium with tridymite in the Cu-Fe-O-S-Si-Al-Ca system have been investigated in the range of conditions of interest to the high- temperature copper production, refining, and recycling processes. An improved experimental methodology has been used involving high temperature equilibration in controlled gas atmospheres, rapid quenching, and quantitative microanalysis techniques using Electron Probe X-ray Microanalysis (EPMA) and Laser Ablation Inductively Coupled Plasma Mass Spectrum (LAICPMS). The effect of oxygen partial pressure on the distributions of minor elements between slag/metal and slag/matte has been accurately measured. The effects of slagging components (Al2O3 and CaO) on the distributions of minor elements between slag/metal have also been experimentally determined. The present study is a part of a larger integrated experimental and thermodynamic modelling research program in the systems relevant to high-temperature copper processing. INTRODUCTION In the high temperature processing of copper, minor elements are distributed between different phases, i.e. liquid slag, liquid matte, and liquid metal. From a processing perspective, it is desired to have the valuable minor elements distribute predominantly in the metal and matte phases rather than in the slag phase, and to have the non-valuable minor elements distribute predominantly in the slag phase rather than in the metal and matte phases. Knowledge of the distributions of minor elements between phases in the smelting, converting, and refining processes is required if the distributions of minor elements between phases in these processes are to be optimized.

Jan 1, 2019

By S. Beskri, N. Geoffroy

When metallurgical plants are designed, a lot of consideration is almost always given to material selection and possible damage mechanisms. Materials engineers are generally involved and will strive to select optimal alloys or refractories for the design conditions. Once in operation however, things often change. Equipment is overstressed to increase production, corrosive leaks are not always promptly addressed, proper welding procedures are disregarded, etc. This paper describes various cases from the mining and metals industry where serious mishaps, associated consequences, and costs could have been avoided if simple and proactive steps had been taken. It also presents a strategy, based on safety reviews, to help predict and prevent damage to critical pieces of equipment.

Jan 1, 2015

By James H. Savory

"In recent years, there has become a growing interest toward a better understanding of balance rope behaviour. With this in mind, the auth or will present a comprehensive summary of field experience, as well as conclusions. In presenting this overview, it is the intent to stimulate further interest as well as provide a framework from which further in-depth investigation can be initiated.Topics which will be covered include rope cores, lubrication practices, loop dividers, rope failures, etc.IntroductionThe first friction hoist was designed in Belgium in J862 by Lemielle. However, it was not until 1877 when Carl Frederich Koepe installed a friction winder sheave at the Hanover Colliery in Germany, that the design was given serious consideration. The winder consisted of a motor-powered sheave over which a single rope was installed, and the end s attached to two conveyance s. Beneath the conveyances a rope was connected, designed to reduce the chance of slip. This was the first balance rope.This earl y mod el is a far cry from the modern tower or ground mounted Koepe winders employed throughout the mining industry today. There have been vast improvements in all aspects of the Koepe winders. One such improvement is in the balance ropes used. This particular area will be concentrated on, with emphasis on selection, maintenance and field experience.SelectionThe sale purpose o f a balance rope is to counter the head rope weight. Obviously then, in selection o f balance ropes, weight is of primary concern. Usually the head and balance ropes are equal in weight. However, sometimes balance ropes which are 5 to 10070 heavier than the head ropes are employed. These reduce horsepower demands during peak acceleration periods, and assist in overcoming inertia during retardation periods. As well, it is sometimes preferred to reduce the balance rope weight, in order to compensate for the eventual weight buildup of lubricant, dirt and debris."

Jan 1, 1983

By W. Dresler

"A major Canadian chromite deposit at Bird River, Manitoba is one of the largest known chromite reserves in North America but it exhibits low chromium contents and low chromium to iron ratios. Commercial beneficiation techniques permit these ores to be upgraded to concentrations which, however, remain inferior to most other ores and concentrates used worldwide f or production of high-carbon ferrochromium. Analyses for reduction of low-grade concentrates by submerged-arc electrofurnace techniques predict chromium contents between 45.9% and 51% for a high-carbon ferrochromium alloy. Relatively high over-all chromium recoveries between 79.5% and 91. 1% can be achieved. Alloy compositions for Cr, Fe, C and Si are determined for various burdens with low-grade concentrates. Consumption data per ton contained chromium are obtained for electric power, coke, concentrate, quartzite and limestone. The data are compared with those of high-carbon ferrochromium producers in South Africa. Economic aspects are discussed and compared with a South African reference study.IntroductionThe present ferrochromium demand in the western world is estimated at approximately 1.7 Mt with a consumption of approximately 0.36 Mt in the U.S.III and 0.03 Mt in Canada'-', A low estimate of the installed production capacity for ferrochromium in the non -communist world is 2.4 Mt. This production capacity of ferrochromium by far exceeds the demand, which is also evident from the fact that no shortage in supply of ferrochromium to the world markets was encountered in the past. Supply-demand comparisons therefore suggest that in the foreseeable future no new chromite or chromium producers should enter the world markets unless superior chromites or superior technologies are successful in competing with existing producers. Neither one of these conditions exist presently in Ca nada or the U.S., although essentially no ferrochromium is produced and no chromite is mined in these countries at the present time."

Jan 1, 1986

By C R. Crook

A brief outline of production methods and processes is given to show how maintenance fits into the picture at this plant. The work force, and the tools needed to carry out this function, are then described. Preventive maintenance practices, scheduled annual shutdowns and routine check-downs are explained, especially as related to planning and to the materials and labour involved for a mini-mum downtime. A brief explanation of the materials, sup-plies and spare parts program, as well as the part played by the Stores Department in conjunction with the Maintenance Department, is given. Cost control and equipment expenditure indicators are explained. Some specific examples of maintenance jobs are described in order to show the flexibility of the program. S HERRITT GORDON Mines Limited has been in continuous production, except for the planned downtimes needed for expansion tie-ins, or the annual shutdown check-over periods, since the first shipment of nickel on a commercial basis in July of 1954.

Jan 1, 1964

By R. H. Coloquhoun

"INTRODUCTIONDome Mines Limited is located on 3,149 acres in Tisdale, Whitney and Shaw Townships in the City of Timmins in Northern Ontario. The mine and mill facilities are two miles from the town of South Porcupine, now part of greater Timmins.In April of 1909, J.S. Wilson of Massey, Ontario headed a party of prospectors into the Porcupine region. Disembarking from the Temiskaming and Northern Ontario Railway at mileage 222, they established an initial camp on the shore of Frederick House Lake. Following the lake ""break up"" they canoed to their destination, Porcupine Lake, and established a base camp on the west side of the lake by May 23, 1909. At a point approximately two miles from Porcupine Lake the moss on an outcrop was rolled back and gold was discovered.In the spring of 1911, the first mill structure was in the process of being built and consisted of 40 stamp mills, five S'x22' pebble mills and the ancillary equipment for a 300-400 T.P.O. operation. This structure was destroyed along with much of the Porcupine Camp by the famous Porcupine Fire of July 1911. By mid-1912, a steel ""fire proof"" structure was built and utilizing the salvaged mills from the fire, supplemented by the installation of three, 8'x30"" cylindro-conical Hardinge ball mills purchased third hand from Vipond Mines, processed 75,088 tons by year's end.The mill was again levelled by fire in October of 1929, this time caused by an overheated boiler stack. This 11 fire proof"" structure was immediately replaced by a wood structure and again the three Hardinge conical mills and the five 5'x22' pebble mills were restored and utilized. The new mill operated close to its daily capacity of 1500 tons during the last two months of 1930. During the rebuilding phase, the crushing plant was remodelled and a new crusher installed. These plants were protected from fire by a 60,000 gallon water tank and an automatic sprinkler system."

Jan 1, 1984

By Y. Kashiwaya, J. Yagi, P. R. Austin

The problems of global environment and resources have become important issues in recent years, and the iron and steelmaking industry is requested to decrease energy consumption and carbon dioxide emission. The improvement of efficiency of ironmaking system is one of the countermeasures for these problems because more than a half of total energy input to the integrated steelwork is input to the ironmaking system. Various approaches to improve the blast furnace process have been made. The authors examined their performances through mathematical simulations of blast furnace operation, and confirmed the improvement of blast furnace efficiency under some operating conditions. The ironmaking system consists of various processes, and the materials and the energy are transported among these processes. Thus it is necessary to evaluate the efficiency of the novel operation of blast furnace based on the ironmaking system. In this study, the balances of material and energy on ironmaking system that consists of blast furnace, coke oven, sintering and hot stove processes were analyzed. The operation status of each process in the system was adjusted according to the results of the operation simulation of the blast furnace under novel operating conditions. The analysis clarified the effect of the blast furnace operation on the energy balance and CO2 emission of the ironmaking system.

Jan 1, 2015

By B. Van den Bogaert, K. Binnemans, T. Van Gerven

Europium is one of the most critical rare-earth elements due to the limited supply of this element combined with a high demand for red lamp phosphors. Therefore, the recycling of europium from end-oflife lamp phosphors has become increasingly important. Photochemical reduction of europium(III) to europium(II) and subsequent removal from rare-earth mixtures by precipitation as EuSO4 is a very selective and efficient method to recover europium from binary europium/yttrium solutions. It is shown that full separation of europium and yttrium is feasible from laboratory prepared non-equimolar Eu/Y mixtures up to a ratio of 1/20, which reflect the composition of red lamp phosphors. Optimal conditions were determined at pH 4 with isopropanol as a radical scavenger, which is a less harmful and toxic compound than the commonly used formic acid scavenger. Europium removal efficiencies of more than 95% were achieved, with a purity of 98.5% of the EuSO4 precipitate. The irradiance of the used light source, expressed in mW/cm2, has a large impact on the illumination time needed to remove europium from the solution. It is observed that higher irradiance results in a shorter induction time, i.e. a period during which virtually no europium is removed, and a faster removal rate once the induction time has passed. The photochemical separation technique was applied to recover europium from leached industrial red lamp phosphor (YOX) powder, with a Eu/Y ratio of 1/30. Europium recovery of 50% was reached with a purity of 96%, proving the feasibility of this method for the recycling of europium from end-of-life lamp phosphors.

Jan 1, 2016

By J. B. Mitchell

Many of the pre-production and plant startup problems that we regard as inevitable are actually caused by poor organizational methods. Traditional methods of organization can be modified to provide clear definitions of responsibility, continuity and depth of involvement of key personnel in order to overcome these problems.

Jan 1, 1966

We describe a new method of characterising the effect of dissolved materials on the rate of coalescence of bubbles in aqueous media. Single bubbles were allowed to rise to meet the surface of an aqueous solution, and the time of persistence between arrival and bursting of bubble was measured as a function of solute concentration. A laser beam was placed just above the surface of the liquid, with a detector in the light path, so that any disturbance at the surface could be seen as a break in the beam. The arrival of a bubble at the surface could be detected from the behaviour of the trace on an oscilloscope, and when the bubble broke, another significant change in the signal could easily be seen. The time between disruptions was reported as the persistence time. The effect of a homologous series of n-alcohols (C1 to C8) on the persistence time was measured, in aqueous solution. It was found that with increasing concentration of a particular solute, the persistence time increased up to a point, and then declined. However the magnitude of the persistence time was found to increase with increasing numbers of carbon atoms in the molecule. Bubbles of 1, 2 and 3 mm diameter were used. Persistence time increased with increasing bubble diameter, the maximum values observed being of order 100 secs. For a given solute, the persistence (drainage) time increased with increasing bubble diameter. The concentration Cmax at which the maximum persistence time was observed, was found to be independent of the bubble size. It decreased uniformly as the carbon number increased, and was well correlated by the function y1/2 (dy /dc) -2 I dc)-2 . There was no apparent correlation with the surface excess at maximum persistence time.

Jan 1, 2006

By John S. Stevenson

THE Twin "J" Mine, operated by Twin "J" Mines, Limited, represents an amalgamation of the old Lenora, Tyee, and Richard III mines (see Figure 1) on mount Sicker, eight miles by road, northwesterly, from the city of Duncan, on Vancouver island. These mines produced 253,000 tons of copper-gold ore between 1898 and 1909 (see Table I). During the more recent period of production from these properties, July, 1943, to May, 1944, Twin ?J? Mines, Limited, mined and milled ore with values mainly in copper and zinc, and minor values in gold, silver, and lead. Figures are not available for this later production. Field work at the property was started by the writer in 1941 and continued in 1943 and 1944.

Jan 1, 1945

By Y. M. Shneerson, V. M/ Shpaer, E. E. Zhmarin, A. Y. Lapin, E. M. Vigdorchik

This paper describes studies of zinc concentrate oxidizing pressure leaching using the method of mathematical modeling. The concept of a kinetic function was taken as a basis for mathematical modeling of the leaching process. The kinetic function describes dependence of the unreacted component share OJ on the relative time x (the relative time is the ratio of the test duration and the time of complete dissolution). This kinetic function is determined in accordance with the results of batch laboratory tests. The laboratory tests have been carried out on zinc concentrate produced from Kazakhstan zinc-copper ores. Zinc concentrate consisted mainly of three types of minerals: sphalerite (70%), pyrite (13%) and chalcopyrite (10%). Oxidation reactions of sphalerite, pyrite and chalcopyrite have been considered as principal ones. The kinetic characteristics of the process (kinetic function, reaction order, activation energy, duration of complete dissolution of the concentrate components) have been calculated in the course of laboratory tests. The mathematical model was used for estimation of the main technological leaching process parameters (such as process rate, degree of metals extraction, autoclave capacity, heat balance, etc.). Mathematical modeling based on the kinetic function concept allows safe designing of metallurgical equipment and scaling the technology to industrial capacity.

Jan 1, 2004

By L. J. Cabri

A gold sample assaying 11.4 g Ault was selected for this study. Approximately 99% of the gold in this sample occurs as discrete gold minerals; the balance occurring as invisible gold in pyrite (determined by SIMS analysis). The sample was coarsely ground and sieved, yielding -38, 17, 22 and 22 wt.% in the -400+160 um, -160+80 um, -80+40 µm and -40 µm size fractions. Assays of the size fractions gave a gold distribution of -32, 20, 21, and 27% respectively. Processing with the hydroseparator (model HS-02) gave two tailings products and one concentrate from each size fraction. Assays of the concentrate from each size fraction gave gold recoveries of -7, 7, 24, 19%, respectively. Polished sections were prepared from each hydroseparation product and studied by image analysis to automatically search for gold minerals. Calculations were done using the surface area of the grains of gold minerals found on the polished sections.

Jan 1, 2005

By Cesar H. Oboni

The development of specific risk-based methodologies to guide and prioritize clearing decisions in countries contaminated by Unexploded Ordnance and Land Mines (generically defined as Explosive Remnants of War: ERW) either at country-wide scale or road-network-scale was used in an unexpected way when a large mining company asked Riskope (www.riskope.com) to develop a multi-modal transportation network risk assessment plan, which included ocean going vessels, ports, wharves, railroad, trucking and other modes of transportation. What had been a first-in-the-world attempt in the humanitarian landmine clearing industry turned out to be extremely useful and equally innovative in the extractive corporate world. Instead of a country contaminated by man-made hazards such as Explosive Remnants of War (ERW) we were now dealing with a very complex multi-modal transportation system afflicted by all sorts of potential hazards from quakes to climate change, sabotage to labour strikes, and vulnerable infrastructures to potential energy crises. Interestingly enough the method developed to deal with ERW risk based clearing was also capable of solving the transportation risk evaluation problem, after necessary customization. This paper shows how ?out of the box? thinking and industry cross dissemination can bring significant evolution and a competitive edge even to unexpected areas of the world-wide mining industry. The results of the logistic system risk assessment shed new light on the management of the system, changed the way insurance coverage was purchased, and led to significant potential cost reductions in a period of global recession.

May 1, 2010