Search Documents

By W. R. Lindsay

Considerable attention has of late been given to the blasting of large amounts of ore in one operation, on account of the saving in labour and explosives and consequent low cost per ton, and also on account of the additional safety to employees. The blast here described, at the Hidden Creek mine. at Anyox, B.C., is not necessarily unique either in size or methods employed, but some interesting p10blems were encountered and the solutions of these may be of interest to others engaged in similar work. The ore consisted mainly of old scope-bottoms and sill pillars, although there also were some braces and parts of vertical pillars included. Some of the stope-bottoms were overlain by caved waste, and one of the problems was to break them in such a manner that the maximum amount of ore could be recovered without serious dilution with waste. The ore blocks, designated as the 385 silt and the 7 A-103 blocks, were under preparation for blasting for over a year, as conditions permitted. This work consisted in drilling long machine drill holes, varying in length from 14 to 20 feet. These holes were drilled with the Numa detachable bit, made locally, starting at 2~-inch diameter and bottoming at 2 inches for the longest length. The long hole drilling was used in the thinner sections of the area. For the stronger, thicker portions, powder drifts (3 ft. by 4 ft. in section) were driven for the powder charges. Reference to the plan and sections (Figures 2 co 8 inclusive) show the relative location of these, as well as the long drilling. The amount of explosives used in the powder drift charges averaged 0.25 pounds per ton of estimated burden, varying from 0.2 to 0.3 pounds per ton.

Jan 1, 1934

By L. K. Daneshmend

Key issues in managing information systems in the minerals industry will likely continue to be those relating to the integration and interoperability of disparate systems. This paper argues that, in order to harness the promised benefits of information technologies, the mining industry should adopt a set of open systems standards to define data formats and protocols for seamless data exchange. This is in direct contrast to the present situation where mining equipment, software and instrument suppliers rigidly adhere to proprietary standards for fear of losing competitive advantage. Benefits to the mining sector resulting from the adoption of such standards would be: the provision of near-time data for executive decision support, and the freedom to choose best technologies. The principal benefits to the leading mining software suppliers will be increased market share as a result of “captive sites” converting to open systems standards. Examples are given of open systems standards developed for related industries such as the Petroleum Open Systems Corporation (POSC) and the Machinery Information Management Open Systems Alliance (MIMOSA).

Jan 1, 2000

By R. A. Brown

RIGHT NOW the Canadian oil business is suffering from growing pains brought on by developments outside our borders. I would like, therefore, to place our industry in perspective for you in two ways. I would like first to describe it briefly and let you see it in relation to the world oil industry. Then I would like to bring it back and place it into perspective against a strictly Canadian background. Naturally, in such a discussion, it is necessary to use a certain amount of statistical material. I'll endeavour, however, to keep it to a minimum. Eleven years ago, before the discovery of Leduc, Alberta could boast of having 21,000,000 barrels of crude oil reserves. Five years ago we had 1,810,000,000 barrels. At year end, 1957, our remaining recoverable reserves totalled more than 3,000,000,000 barrels. In 1957, our potential production in Alberta reached an all-time high of 756,000 barrels a day. Unfortunately, our actual average daily production dropped from 393,000 barrels per day in 1956 to 376,000 barrels per day in 1957. And in 1958, to date, it has dropped sharply to around 300,000 barrels per day.

Jan 1, 1958

By B. K. Choi, G. E. Kim, S. Noh, T. K. Kim

Oxide dispersion strengthened (ODS) steel has been developed as the most prospective core structural material for next-generation nuclear systems because of its excellent high strength and irradiation resistance. In ODS steel, finely dispersed nano-oxide particles with a high number density in the homogeneous grains can be very attractive to achieve superior mechanical properties at high temperatures, and these favorable microstructures can be significantly changed using process parameters during the mechanical alloying procedures. In this study, the effects of mechanical alloying times on the microstructure of 10Cr-1Mo ODS martensitic steel were investigated. Pre-alloyed powders with Y2O3 powder were mechanically alloyed for various milling times using a high energy horizontal ball-mill apparatus (model: symoloyer CM20). Powder properties such as the mean particle size, size distribution, and crystallite size were evaluated. Uniaxial hot pressing was employed to consolidate the milled powders. The results of a microstructural observation after the MA and UHP processes indicated that the homogeneity of the martensitic structures was considerably increased with the longer milling time. It is thus concluded that the mechanical properties of the ODS martensitic steel are greatly dependent on the mechanical alloying times.

Jan 1, 2015

By R. S. Boorman, H. G. Ansell

"Poor separation of lead from a copper concentrate of a major base metal producer was thought to have resulted from copper (0.2-0.4%) in the galena which caused it to float with chalcopyrite. No inclusions of copper mineral were detected which could account for the flotation of galena. The tendency for copper-bearing galena to float with chalcopyrite was confirmed by Hallimond-tube experiments in which the floatability of copper-doped synthetic galena (0.1-0.4% Cu) was approximately four times as high as copper-free galena. The difference in the cell edge (5.9338 ± 0.0003 A, Cudoped galena; 5.9361 ± 0.0002 A, Cu-free galena) indicated that the copper was lattice-bound and did not occur as submicroscopic mineral inclusions."

Jan 1, 1973

By E. Dernedde

A few studies have suggested that the rate of adsorption of hydrogen fluoride on smelter grade alumina is determined by kinetic factors. However, no performance equation for dry scrubbers has appeared in the literature so far. Experimental data from a pilot dry scrubber with co-current flow were compared with results of kinetic models of adsorption, film diffusion and pore diffusion. The pore diffusion model was deemed the most appropriate. It was transformed into a performance equation for steady-state operations of dry scrubbers by the inclusion of the alumina recirculation. Operating results of industrial dry scrubbers with co-current flow were successfully evaluated by means of the performance equation. The average fluoride content of the alumina was also estimated by using the pore diffusion model.

Jan 1, 2011

By M. E. Holuszko

A research program has been carried out at the Mining Department of the University of British Columbia to study the effect of wettability of coal on its handleability and bulk density. The effect of moisture content on the bulk density of coal was found to be more pronounced for hydrophilic coals than for hydrophopbic ones. Altering wettability of coal surface leads to different effects of moisture on bulk density. The samples were studied at different fine fractions content, and it was shown that there was no effect of increased content of fines on the bulk density for hydrophobic coals, while for hydrophilic coals this effect was very significant. It was shown that the moisture content at which the lowest bulk density was reached coincides with the critical moisture content for studied samples, as determined from handleability tests using Durham Cone method. This critical moisture is the moisture content at which a sudden deterioration of coal handleability occurs. Based on the bulk density and handleability tests, the flow theory of moist coal is proposed.

Jan 1, 2006

By Robert A. Bosschart, Harold O. Seigel

"Most electromagnetic methods presently used in mining exploration are of the moving source type; i.e., the primary field source is moved simultaneously and in a fixed configuration with the receiver. Of the fixed-source methods, which employ a stationary primary field and a moving receiver, the Turam method is the most effective and has marked advantages over alternative electromagnetic methods. The results are little affected by topographic relief, and a high degree of resolution can be obtained because of the constant relation between source field and investigation area. Another inherent advantage of the Turam configuration is that it provides more favourable dimensional relations. Thus, the primary field attenuates at a much lower rate than in moving-source configurations and, secondly, the method is size sensitive; i.e., conductor size affects the strength of the response, which is not the case with moving-source methods. These factors result in a considerably better potential depth penetration."

Jan 1, 1966

By M. Lytle

"The Corbin area of southeastern British Columbia has been a coal mining area since 1908. Byron Creek Collieries Ltd. Has operated its Coal Mountain Mine in this area from 1974 until the present. In February 1981, this company was purchased by Esso Resources Canada Ltd.Coal Mountain is structurally complex and standard computer algorithms are not applicable to model the overturned synclinal structures and faulted bedding surfaces. This paper discusses two approaches used by Esso Resources staff to model the geology of Coal Mountain.The first approach projects digitized cross-section data along trend to develop a large data base which correctly approximates the shape of the structure. The spatial orientation of the structure is corrected by merging the generated data set with drill-hole data. The second approach uses digitized cross-section and bench-plan geology to generate a block model of the coal reserve.HistoryThe Coal Mountain Mine, also known as the Corbin Mine of Byron Creek Collieries Ltd. is located 24 kilometres south of Highway 3 in southeastern B.C.In 1905, two American businessmen recognized the coal potential of the area during a horseback tour. The two businessmen, D.C. Corbin and E.J. Roberts, formed the Corbin Coal and Coke Co. to mine and market coal from their newly acquired 6075 hectares of coal licenses. By 1908, the town of Corbin was under construction, a 22.4-km rail spur was constructed from the mine to the main CPR line and the first underground mine began to produce coal. An open-pit operation was also developed at the 1828-metre elevation using a steam shovel loading into rail cars. The company operated continuously until 1935, when a lengthy strike forced suspension of operations.In 1943, the Consolidated Mining and Smelting Company Ltd. (now known as Cominco Ltd.) operated two surface mines to produce coal for its smelters at Kimberley and Trail, B.C. This operation ceased in 1948."

Jan 1, 1982

By George F. Crocker

Introduction The Helen mine and the Victoria mine of Algoma Ore Properties, Limited, in the Michipicoten district, Ontario, are 120 miles north of Sault Ste. Marie, on the north shore of lake Superior. They are on the Algoma Central railway between Hawk Junction and Michipicoten Harbour. Between them, these mines have produced 10,757,113 tons of iron ore. From 1900 to 1918, 2,823,369 gross tons of brown ore was shipped, and from 1939 to the end of 1949, 7,933,744 tons of siderite was produced from the open-pit operations and underground development. The finished product, known as 'Algoma sinter', is shipped to blast furnaces both in Canada and the United States. The iron-ore bodies are a part of a tabular shaped area of iron formation that extends over a length of more than 10,000 feet and has maximum width of 1,000 feet. The two siderite orebodies, known as the Helen and Victoria, are separated by two diabase dykes. The Helen orebody is 1,600 feet long with a maximum width of 250 feet and the Victoria is 1,200 feet long with a width comparable to the Helen. These orebodies are considered to be a replacement of the original rock by iron carbonate. The introduction of the iron-1bearing material probably occurred after the development of the major folded structures. The open-pit mining of siderite started in the Helen ore body in 1939 and continued until 1945. During this period, 3,853,395 tons of ore was mined. Open-pit mining started in the Victoria body in 1946 and is still being carried on. Underground development commenced in September, 1947. Diamond drilling and surface sampling had shown the Helen deposit to average 35.61 per cent Fe and 7.28 per cent SiO2, and the Vi.otoria deposit 33.73 per cent Fe and 10347 per cent SiO2?

Jan 1, 1950

By G. Vibert Douglas

It has long been recognized that there are considerable difficulties connected with the physical and chemical explanation of shoots of ore. The literature of Mining Geology has frequent references to this subject; but the reasons given for the actual location of primary ore-shoots have been very tentative. In practice, the geologist or miner depends to a great extent on sampling and assaying to determine the boundaries of profitable ore within the mineralized zone. An ore-shoot is a portion of a mineralized zone which has a sufficient concentration of valuable minerals to make it ore. Ore deposits have been classified according to many schemes. There are classifications based on morphology and on genesis. However, it is also possible to classify hypo-gene hydrothermal ore-bodies in terms of ore-shoots or vice versa. A.-Ore-deposits in which the whole of the mineralized zone is ore, which is the same as saying that the ore-shoot extends throughout the mineralized zone. An example of this type of deposit would be the pyritic mineralization of Rio Tinto. B.-The second type would comprise those deposits in which the ore-shoots bear some relation to the geological structure of the area: all deposits in which 'bonanzas' occur in folds in the zone, at the intersection of veins along certain fault (or joint) features and other such controls. There are a great many examples of this type: (a) The Rhodesian copper lodes, where Bancroft and Gray have pointed out the association of the shoots of ore with drag folds. (b) A similar association has been pointed out by Faribault for some of the gold veins of Nova Scotia, e.g., Mount Uniacke. (c) The great bonanza of the Comstock lode in Nevada. C.-Deposits in which the localization of ore has been effected by the chemical character of the wall-rock. Examples of this type are the Fahlbands of Scandinavia, and the 'indicator' deposits of Ballarat, Australia. D.-Lastly, deposits in which there is apparently no structural and no chemical control.

Jan 1, 1934

By P. Czaja

The paper presents a patented and copyright protected concept of constructing a shaft lining that goes through rock masses having strong rheological properties and being susceptible to leaching. In the case of salt layers, especially at significant depths (over 900 m) the relative convergence of the heading contour may amount to 40 ?/year. That results in the fact that any other method of securing the shaft lining, e.g. by making it flexible, will not be sufficient to ensure the stability of the shaft reinforcement geometry. In the new shaft lining concept the excessive rock creep into the outbreak inside the shaft diameter will be removed by local and controlled leaching of the shaft cheeks by means of fresh water directed through a porous medium at the contact layer behind the watertight tubing lining. The paper presents the structure of such a lining and an outline of the construction technology. In order to implement such a lining, a typical tubing will be applied. Separate design and manufacturing will be required for the technological rings used to control the leaching process behind the lining.

Aug 1, 2013

By A. S. Dawson

"IntroductionTHE PURPOSE of this paper is to describe the results of a preliminary investigation of a method thought to be useful in interpreting geological structures in un-metamorphosed sedimentary rocks. The writer is not aware of the method having been described or investigated previously, although no thorough search of the literature has been made.The method to •be described is based on the assumption that, in argillaceous sedimentary rocks, certain ceramic properties are diagnostic for certain beds within areas of variable limits.Two ceramic properties• have been investigated: pyrometric cone equivalent (P.C.E.), and bloating characteristics of shales. The enquiry has been directed toward testing the usefulness of these properties in determining the following:A -The correlation of shale beds and, by inference, of coal seams, sandstone beds, or other such structures associated with them.B.-The location of contacts between marine and non-marine shales where lithological, palaeontological, or other evidence is lacking.Limitations of time and facilities have prevented a thorough investigation of this problem. The results given in the present paper are preliminary only. It is hoped, however, that they will occasion discussion or even lead to more thorough investigation of the method by individuals or organizations.There are, admittedly, various limitations to the proposed method. It is thought to show some promise when used in conjunction with the well-known and established methods used in stratigraphic correlation and, more particularly, when the conventional methods are not applicable."

Jan 1, 1952

DOME MINES, Limited, is a gold producer situated in the Porcupine area of Ontario, 500 miles north of Toronto. During the year 1960, '71 4,600 tons of ore were milled, yielding gold bullion valued at $6,025,370. Prior to conversion to natural gas, an average of 3,200 tons of coal was consumed annually, one third of which was obtained from Canadian sources with the remainder coming from the United States. Due to the distances involved, the freight charges increased the pithead cost by as much as ISO per cent. Steam is generated at a central boiler plant and used for timber treatment, plant heating and process steam. Until August, 1960, steam was supplied during the winter months by two water tube coal-fired boilers, each rated at 200 boiler horsepower at 100 per cent output. Steam requirement was as high as 150 per cent of boiler rating in the colder periods. The summer load was

Jan 1, 1962

Mirador - Overview ? Located in Andean foothills of SE Ecuador ? Copper-gold porphyry hosted by calc-alkaline Late Jurassic granitic and porphyritic rocks ? 438 MT of 0.61% Cu and 0.19 g/t Au measured and indicated resources (at 0.4% Cu cut-off) ? Additional inferred resources of 235 MT of 0.52% Cu and 0.17 g/t Au ? Initial 25,000 tonnes/day production, expanding to 50,000 in year 6 320 MT of 0.62% Cu, 0.2 g/t Au ore mined at an average 1.4:1 strip ratio over a 21 year mine-life

May 1, 2006

By R. Harrisson, K. Esmaieli

Brunswick mine employs an ore and waste pass system for material transfer. This paper reviews the evolution and performance of ore pass systems at the mine. It presents the range of selected configurations, inclination, dimensions, etc. Select case studies are used to address the influence of structure, stress and materials handling on the longevity of the employed ore passes.

Jan 1, 2008

By A. L. Mular

This paper provides a worthwhile contribution to the knowledge needed for calculating and using mathematical models of grinding circuits. The computer search algorithm proposed should remove much of the guesswork as well as reduce computer processing costs and improve the accuracy of estimated parameter values for grinding mill models.

Jan 1, 1970

By L. A. Clark, G. H. R. Burrill

"Most unconformity-type uranium deposits in Saskatchewan occur within a few tens of metres above and/or below the basal unconformity of the 1,45-b.y. Athabasca Sandstone. Graphitic basement rocks coincident with post-Athabasca faulting or brecciation at or near the unconformity are important in localizing uranium deposits which form as tabular, ribbon-like bodies with grades averaging over 2 per cent uranium and containing up to 50,000 tonnes UJOs. Some of these deposits have similar contents of nickel and arsenic.In the genetic model proposed to explain these deposits, traces of uranium were leached from the sandstone and weathered basement rocks by oxidized formation waters sweeping through the sandstone and along brecciated faults. Over basement meta-petites, a thick clay regolith adsorbed uranium from the solution. Thus fixed, the uranium was reduced through an indirect reaction with graphite, possibly involving methane. The clay mineral surfaces were thus continuously cleared to allow further adsorption. Basement faults localized along weak graphitic units were re-activated, offsetting the sandstone formation, probably at the time of an early uranium deposition about 1.2 b.y. ago, and served as vents for spent ore solutions. Fluid convection was induced by topographic relief and/or crustal heating from radioactive decay in basement plutons or mantled Archean domes with uranium and/or thorium contents a few ppm above those of adjacent rocks. Heat from radioactive decay within the incipient uranium deposit would develop in about a million years. The self-generating convection cell would continue uranium deposition until all permeability was plugged by minerals. In some instances, convection was re-initiated after subsequent faulting and brecciation. While some deposits were further enriched, heavy flows of oxidized fluids re-dissolved and partially depleted other uranium deposits.The East Alligator Rivers uranium deposits in Northern Territory, Australia, occur within Middle Proterozoic quartzchlorite and quartz-muscovite schists overlain by sandstone. Highest grades occur in silicified breccias where carbonate beds were leached out. Mineralization ages are both pre- and post-Kombolgie Sandstone, but, to date, no significant uranium mineralization has been encountered in the sandstone. There are many general similarities with Saskatchewan deposits, but important differences in detail."

Jan 1, 1981

By H. R. Oliveira, C. R. Aragonez de Vasconcellos

Pipeline operation and maintenance necessarily involves geotechnical studies at points and areas with deflagrated instabilities or still to map and monitor areas prone to geotechnical problems. Landslides, erosions and debris flows are some examples of natural hazards, that not rarely, can bring high consequences to pipelines, sometimes leading them to high stresses levels and ruptures. Bolivia-Brazil Natural Gas Pipeline has 2.593 kilometers since Rio Grande City in Bolivia until Canoas City, in south Brazil. The pipeline crosses a lot of types of geological fields and difficult topography. The south spread of the pipeline has the most prone areas to geotechnical hazards because of its hard topography combined with the variety of geological materials, such as, colluvium deposits and debris flow areas. The aim of this paper is to present the right-of-way geotechnical risks that affect pipelines, presenting some practical remedial works done by TBG at Bolivia-Brazil Natural Gas Pipeline as well as the integrity plan and the adopted actions in way to prevent geotechnical accidents.

Jan 1, 2005

By G. Lodewijks

This paper explores the savings that can be achieved in the energy consumption of belt conveyors used in mines by changing the conveyor components, the operational parameters of the system or the belt properties. First the concept of energy savings is introduced by looking at the energy consumption of belt conveyors from a theoretical point of view. Also methods for the calculation of the power consumption of a belt conveyor and the associated emissions are presented. Two case studies are presented in which the effects of the change of the operational parameters of the system, in this case the belt speed, and the belt properties, in this case the application of aramid products in the belt, are presented.

Aug 1, 2013