Search Documents

By B. Panton, J. Carvalho, E. T. Brown

High-capacity, post-tensioned anchors have found wide-spread use in initial dam design and construction, and in the strengthening and rehabilitation of concrete dams to meet modern design and safety standards. Despite the advances that have been made in rock mechanics and rock engineering during the almost 80 years in which post-tensioned anchors have been used in dam engineering, some aspects of the rock engineering design of high-capacity rock anchors for dams have changed relatively little over the last 30 or 40 years. This applies, in particular, to the calculations usually carried out to establish the grouted embedment lengths required for deep, post-tensioned anchors. These calculations which involve a number of aleatory and epistemic uncertainties, usually make simplified assumptions about the distribution and values of rock-grout interface shear strengths, the shape of the volume of rock likely to be involved in uplift failure under the influence of a system of post-tensioned anchors, and the mechanism of that failure. The resulting designs are generally conservative. These aspects of the rock engineering design of large, post-tensioned rock anchors for dams could be improved by making greater use of modern, comprehensive, numerical analyses in conjunction with 3D models of the rock mass structure, realistic rock and rock mass properties, and the results of prototype anchor tests in the rock mass concerned.

Jan 1, 2015

By A. Chamanara

The gross vehicle weight (GVW) of an ultra-class mining truck comprises the unsuspended weight below the struts plus the suspended empty vehicle weight, plus the payload. Theoretically, one third of the suspended total weight is supported by two front struts and two thirds by two rear struts. However, since the payload position is not fixed when placed in the truck body and varies from load to load, compounded by uneven haul road profiles, the truck structure experiences higher than normal stresses, which manifest in the reduction of the life of the truck via structural fatigue. The downstream effects are a decrease in production and increase in operational and maintenance costs. In order to control the dynamic forces causing the high stresses on the truck structure, both the haul road conditions and the load distribution in the truck body need to be investigated. The latter aspect is the prime focus of this paper. A field test has been conducted in an oil sands mine where the Caterpillar 797B trucks are loaded by a Bucyrus 495 shovel. The strut pressure readings are collected using the data-loggers on the trucks as well as the truck velocity associated with each reading. Rack, roll and pitch are the main key performance indicators (KPIs) that are calculated to study the adverse effect of an unbalanced payload and consequently the truck structure. Finally, the shovel bucket load passes within the truck body are simulated and a new method is suggested to improve the truck payload balance.

Aug 1, 2013

By J. J. Hussey

"Abstract-The ""Brunswick Horizon"" an informally named ore-bearing unit near the top of the Nepisiguit Falls Formation in the Ordovician Tetagouche Group, hosts the Brunswick No. 6 and No. 12 base-metal mines, as well as the former Austin Brook iron mine, in northern New Brunswick. Detailed structural analysis of the No. 6 and No.12 mines led to the prediction that a massive­ sulfide deposit may have been repeated by F1 folding along the Brunswick Horizon. A subsequent drilling program discovered the new massive-sulfide North End Zone at a vertical depth of 1100 m, 1 km north of the No. 12 underground workings. By the end of 1990, Zn-Pb-rich massive sulfides had been delineated over a strike length of 200 m and a down-dip extent of 170 m. Rock units intersected in the North End Zone are generally thinner and vary somewhat from those at the Brunswick No. 12 mine. Thinning of the hanging wall rocks may be primary, may result from attenuation along F2 folds, or may represent truncation by a thrust fault. The newly discovered sulfide zone indicates that significant potential exists for the discovery of other deposits at previously unexplored depths.SOMMAIRE-Dans le nord-est du Nouveau-Brunswick ""l'horizon Brunswick"" est le nom usuel de la zone qui contient les mines de métaux de base Brunswick No. 6 et No. 12, ainsi que l'ancienne mine de fer Austin Brook, toutes situées sur le dessus de la Formation ""Nepisiguit Falls"" dans le Groupe Tetagouche d'âge Ordovicien. Une analyse détaillée de la structure des mines No. 6 et No. 12 à permis a van Staal de prédire qu'un gîte de sulfures massifs pourrait se répéter dû à une déformation F1, au nord de Brunswick No. 12. Suite à un programme de forage, la nouvelle zone de sulfures massifs appelée le ""North End Zone"", profonde de 1100 rn, et à une distance d'un km au nord des chantiers souterrains, fut découverte vers la fin de l'année 1990, les sulfures massifs riches en Zn-Pb ont été délimités sur une longueur de 200 rn et une hauteur de 170 rn le long du pendage. Les unités de roches intersectées dans le ""North End Zone"" sont généralement plus minces et sont quelque peu différentes de celles de la mine Brunswick No. 12. L'amin­ cissement des roches pourrait être primaire ou être le résultat de l'atténuation le long des plis F2, ou soit tronqué par une faille. La nouvelle découverte d'une zone de sulfures indique un potentiel énorme pour la découverte d'autres g ""tes à ces profondeurs inexplorées."

Jan 1, 1992

By J. D. Wright

This paper describes current milling practice at Endako Mines Ltd., a molybdenum producer in central British Columbia. The various steps in the crushing, grinding and flotation of the ore are outlined, with emphasis on the metallurgy of the latter operation. Tailings disposal and concentrate assaying methods are also described.

Jan 1, 1969

By M. Kawata, T. Amano, T. Miyamoto, K. Shibayama

"The High Pressure Acid Leach (HPAL) plant of Taganito HPAL Nickel Corporation (THPAL), located in Taganito, Philippines, with a nameplate capacity of 30,000 Ni-t/year started commercial operation on October 2013. The plant load was smoothly ramped up and it achieved monthly production equivalent to 33,000 Ni-t/year in 2016. Partial improvement of the plant capacity for the achievement of 36,000 Ni-t/year, as evaluated from the current operation progress of each system is planned for 2017. In this paper, aside from presenting the progress of the plant ramp-up, research and development activities such as the reduction of nickel loss and the improvement of filtration capacity which was achieved by particle size control of ZnS precipitates in the Zinc Removal system are also discussed.INTRODUCTION Taganito HPAL Plant Project History of THPAL Taganito HPAL Nickel Corporation (THPAL) was incorporated in August 2008, as a joint venture of three (3) companies, namely Mitsui Corporation with 15% share, Nickel Asia Corporation (NAC) with 10% share and Sumitomo Metal Mining Corporation (SMM) with a controlling stake of 75%. Aside from its capital share, NAC’s Taganito Mining Corporation (TMC) supplies the ore for the HPAL plant located in Taganito, Claver, Mindanao, Philippines. The objective of THPAL is to produce 30,000 MT of nickel and 2,600 MT of cobalt as mixed (Ni/Co) sulfide by treating nickel laterite ore in the Philippines and exporting to Japan as raw material for SMM’s Niihama Nickel Refinery (NNR) for the next 30 years. In other words, 1.15 wt% of nickel in ore is refined to 99.99 wt% nickel in electrolytic nickel. The mixed (Ni/Co) sulfide is shipped to NNR and SMM provides the technology and management personnel to THPAL plant as well as sulfuric acid which is the main reagent for HPAL process. Figure 1 shows the location of THPAL and current relationship between the stake holders.The Characteristics of THPAL Plant In terms of plant design, a 2-train system is applied for the HPAL circuit considering the reliability of the process, facility and avoidance of whole plant shutdown due to HPAL troubles. The technical data, operation know-how and improvements gained from the successful operation of Coral Bay Nickel Corporation (CBNC) which was established in April 2002 were reflected in THPAL’s plant design. As for the H2S plant, a more economical design was considered which is different from CBNC."

Jan 1, 2017

By C. Sui, J. E. Nesset, M. Li, J. Y. Kim, S. L. Chryssoulis

"A plant study of zinc rougher flotation at Brunswick Mining was conducted using lime, soda ash and a combination of both as the pH modifiers in order to establish the effects on sphalerite and pyrite kinetics and mineral selectivity. The plant sampling and analysis was augmented by surface analysis using TOF-LIMS, SEM and XPS as well as fundamental precipitation and surface-charge studies in the sphalerite Ca/C03/S04 system.The results revealed the important role of carbonate ions in cleaning the sphalerite surface for effective activation by CuS04 to occur, and the beneficial role of combined soda ash and lime in increasing pyrite and galena depression.1.0 IntroductionThe studies reported in this paper were initiated as part of an investigation into the causes of a particularly pronounced seasonal deterioration in metallurgical performance at the Brunswick Mining concentrator during the summer of 1995. The concentrator treats a complex base metal ore having a typical feed composition of 9.0% Zn, 3.5% Pb, 0.4% Cu and 100g/t Ag at a current throughput of 9,000 TPD, although at the time of the problem in 1995, the average production rate was closer to 10,500 TPD. Zinc, lead, copper and bulk (zinc-lead) concentrates are produced with overall metal recoveries of 86% zinc, 63% lead, 60% copper and 60% silver; results which are typical of the lower recoveries associated with fine-grained, highly complex VMS and SEDEX type deposits. The main economic minerals of interest are an iron-containing (7% Fe) sphalerite, galena and chalcopyrite with the main diluent (about 60% wt) being pyrite.Figure 1 shows a simplified flowsheet of the Brunswick milling circuit while the seasonal decrease in summer metallurgy in 1995 is illustrated in Figure 2. Of significance is the rapid drop in copper and lead recovery in June while there is an apparent delay until late August-September before the zinc deterioration reaches its lowest point. A more typical seasonal effect within the experience of the authors is the reverse of the Brunswick situation, namely an improvement in summer performance thought to be associated with improved differential flotation kinetics during warmer weather leading to better mineral selectivity. The historical Brunswick experience was particularly severe during the summer of 1995 with estimated incremental losses of $10 Million for this period. The potential of the very significant economic benefits to be gained from understanding and hopefully improving the annual drop in performance led to an investigation involving the minesite metallurgical group, the Noranda Technology Centre (NTC) as well as researchers in Professor Jim Finch's group at McGill and the surface analytical services and interpretive skills of AMTEL."

Jan 1, 1998

By Jacques Nantel

"The molybdenite property of Brynnor Mines Limited, Boss Mountain Division (wholly-owned subsidiary of Noranda Mines Limited), is situated approximately 360 miles northeast of Vancouver on the east slope of Takom-kane mountain in British Columbia's Cariboo District. Orebodies at the deposit fall into two categories; quartz breccia, and veins and stringers. The development of the breccia ore zone was started in June, 1964. The bulk of the ore is being mined from the stringer ore zone. The ore-body has been divided into 100-foot stopes and pillars. A sub-level blasthole method is used and the broken ore is handled in drawpoints and scram drifts. The development, drilling, blasting and handling of the ore are reviewed. The future pillar recovery operation is also analysed. The paper is also concerned with a scheduled shaft sinking program."

Jan 1, 1970

By J. D. Allan

"IntroductionThe purpose of this paper is to present a general picture of the Lynn Lake nickel area of northern Manitoba. The geology of the area will not be discussed in great detail, nor will the mining op; rations presently being conducted. Both subjects will be treated briefly and, in addition, mention will be made of some of the problems encountered in mapping in the area. some of the questions which still remain unanswered, methods of prospecting that have been applied and the future possibilities of the area.For present purposes, the Lynn Lake area will be considered as extending from west of Lynn lake to east of Barrington lake. Thus, more correctly, it should be termed the Lynn Lake-Barrington Lake area. It comprises five 15-minute map-areas, or a total of 800 square miles, in a block 47 miles east-west and 17 miles north-south.Lynn lake itself is about 120 miles north of Sherridon, Manitoba, the closes t rail terminal. The area is part of the Granville Lake sheet which was mapped by the Geological Survey of Canada in 1932, 1933, and 1935, the results being published in Summary Report 1933. Part C, and as Maps 343A and 344A on a scale of four miles to o.ne inch. In 1940, the McVeigh Lake area was mapped by the Geological Survey of Canada on a scale of 1,500 feet to 1 inch and a map was issued in 1945."

Jan 1, 1950

By Yoshimasa Funakawa, Kazuhiro Seto, Akio Kobayashi

A new hot rolled high strength steel consisting of ferrite matrix and nanometer¬sized precipitates was developed. The ultra fine precipitates were identified as TiMoC2, and the strengthening by the precipitates was evaluated more than 300MPa in case of TS/800MPa grade steel. Due to the strengthening effect of the ultra fine precipitates, alloy elements for solid solution hardening can be reduced. It is notable that the steel shows very high yield strength (730MPa in case of TS/800MPa) and very high local elongation leading to excellent stretch flange formability at the same time. The mechanical properties of the steel are attractive for chassis parts and structural parts of auto body. The steel has been produced commercially, and applied to the parts successfully.

Jan 1, 2004

By F. Rosenblum, P. Spira

A laboratory test has been developed for assessing the patential hazard from self-heating of sulphides. The technique consists in measuring the rate of self-heating, from near ambient temperature, of a 1-kg sample in an insulated chamber controlled at standard atmospheric conditions. The rate of oxygen consumption is monitored simultaneously. The paper describes the apparatus and test procedure, and reports data on various ores and mill products. Tailings known to have caused problems underground when used as backfill have shown heating rates of over 3°C/h. A preliminary hazard rating guide for backfill based on the known behaviour of several sulphide materials is presented.

Jan 1, 1981

By L. Cheng, Y. W. Pan, Y. R. Liu

"Impounding deformation of slope and foundation is significant during and post dam construction. Reservoir impoundment is accompanied with various phenomena, including material degradation, effective stress decreasing and buoyancy in rock masses. These phenomena are related with some engineering concerns like reservoir-induced earthquake, landslide and dam stability. The Malpasset dam and Vajont dam are typical hydraulic projects suffering from seepage in dam foundation and slope, which finally led to failure and landslide. Pore pressure in jointed rock masses is considered in constitutive relation. The expression of effective stress for porous rock with fluids is incorporated into the Drucker-Prager criterion. Based on monitoring data of valley width and dam deformation, the effective stress law is applied to analyse the impounding influence of slope and foundation to Jinping-I high arch dam. The dam is accompanied with complicated topographical and geological conditions. The results show that calculated and monitored values agree well, and the application of effective stress law provides an approach to evaluate dam deformation, stress and stability with impounding effect considered.INTRODUCTIONImpounding deformation of slope and foundation is a common and significant problem during dam construction and operation. This phenomenon exists in a lot of reservoirs in China, like Laxiwa, Ertan, Xiluodu and Jinping-I arch dams, and some dams in Europe. It is related with some engineering concerns like reservoir-induced earthquake, landslide and dam stability. The Malpasset dam and Vajont dam are typical hydraulic projects suffering from seepage in dam foundation and slope. Monitored data indicates that the valley width tends to shrink in hydraulic engineering during the impounding process, which will change the stress and deformation of dam and abutment. Therefore, global stability of dam and foundation should be evaluated with impounding process taken into consideration."

Jan 1, 2015

By Matthew Novak, J. Brent Hiskey

It is well known that when chalcopyrite is put in direct contact with copper in an acidic medium a galvanic cell is created. Chalcopyrite is reduced to iron and sulfur deficient defect phases such as bornite, chalcocite, and at very low potentials to elemental copper. Galvanic conversion experiments were performed using three chalcopyrite concentrates. The first chalcopyrite contained less than 10% impurity phases. The second concentrate had a high concentration of pyrite, and the third concentrate had a high concentration of pyrrhotite. The effect of temperature, acid concentration, chalcopyrite grain size, copper grain size, and agitation on the rate of chalcopyrite conversion was studied.

Jan 1, 2014

By Egbert Burchardt

The challenge of "ore bodies getting steadily harder and lower in grade" was brought to light during the first oil crisis in the 70's. Shortly afterwards, HPGRs appeared on the scene with the promise of saving energy. This combined with developments in wear protection for the rolls ushered in a period of trade-off studies that considered the HPGR as an option to improve project economics or to even make projects feasible at all. Since then, applications of HPGRs at Cerro Verde (Freeport), PTFI Grasberg (Freeport), Mogalakwena (Anglo Platinum), Tarkwa (Goldfields), Boddington (Newmont), Penasquito (Goldcorp), and others have contributed to the creation of a formidable basket of operating experience. Collected through years of successful operation, this information has been used to validate design criteria, scale-up factors and establishing a clearer picture of what "to do" and what "not to do". This paper compares results from various mining operations using HPGRs in their processing plants. Some of the lessons learnt in different operating environments are reviewed in order to support proper implementation and operation of HPGR's. Some of the development programs that have been initiated to improve wear life of the tyres and to reduce overall operating costs are reviewed. It is timely to summarize today?s experience and analyse its implications for existing and new operations.

Jan 1, 2012

By J. E. Udd, L. B. Geller

"Mine-shaft wire-rope discard regulations include, among other criteria, a limited amount of permissible loss-of-breaking-strength (LBS). Currently, this parameter is estimated on the basis of non-destrutive-testing (NDT) with electro-magnetic (EM) type instruments. This paper analyses the accuracy with which these estimates have, so far, been obtained in practice.It concludes that while certain types of testers have produced better results than others, the desired accuracy level has not been attained. Also discussed are the putative reasons for this situation, and appropriate actions that the mining industry might wish to take."

Jan 1, 1990

By R. Browner, J. Collard, D. Ibana

The extraction of cobalt from synthetic pressure acid leach solutions of nickel laterite ores by the direct solvent extraction route using ESPLIM is reported. It first explored the use of gaseous ammonia as pH modifier and then the variables that affect the dispersion of the aqueous phase in the organic phase such as ionic strength, viscosity of the phases, initial droplet size, etc. were explored so that phase hold-up and thus extraction can be effectively controlled. The results show that the technique allows better control of phase dispersion circumventing one of the main weaknesses of conventional solvent extraction.

Jan 1, 2005

By L. Li

Backfill is increasingly used in underground mines, as it can help reduce the environmental impact from mining operations. However, the primary objective of backfilling is to provide safe working space for miners, by improving ground stability conditions. As cement is often added to the backfill, a critical issue is the determination of the required backfill strength (cohesion) due to the binder. This value is usually obtained from a solution proposed by Mitchell and co-workers, in the early 1980?s, for stopes with an exposed backfill face. This paper presents a brief review of the Mitchell et al. solution, with some of its main limitations. Some of the recently developed solutions for backfill design are then summarized and discussed.

Aug 1, 2013

By Fr. -W. Bach

In the past years the enormous weight saving potential of magnesium sheet has been demonstrated by various research projects all over the world. It has been shown magnesium flat products can benefit automotive, aviation, machine tool and consumer electronics industries. Major material problems such as poor formability, corrosion resistance and high production cost still inhibit the application of magnesium sheets in large scale production. The present contribution outlines achievements in casting and rolling technology. The authors developed an adapted strip casting process in which near-net-shape rolling feedstock of several wrought alloys has been produced. During the rolling process, various parameters were varied in order to modify the microstructure and surface quality of sheet. Several temperature cycles, strains, lubricants, roll surface structures and roll coatings have been analyzed. The sheets were examined and tested in deep-drawing experiments. Suitable rolling schedules have been developed for standard and modified wrought alloys. The study concludes with an overview of current industrial solutions and an estimation of the potential cost savings that might result from the adaptation of the process that has been developed.

Jan 1, 2006

By L. Iacopetti, A. Calderara, M. Perego, P. Perrone, T. Furusawa

De Nora, a global leader in the development, manufacture and sale of all DSA® anodes based on titanium coated with mixed metal oxide (MMO) for electrochemical processes will present key advancements made to Self-Protected Anodes (SPA) for metal electrowinning. (DSA® is a registered trademark of Industrie De Nora S.p.A., Italy). In 2017 pre-commercial demonstration cells were operated in industrial environment. The program’s focus was to fully demonstrate the SPA anode’s superior mechanical and electrochemical robustness during normal and induced dendrite shorting occurrences while providing quality of plating in commercial operation. De Nora specialists focus on key components, in particular the engineering of the self-protection system, DSA® anodes and catalyst formulation capable to cope with high levels of pollutants while providing long service life in the meantime. Results of field trials confirmed the expected anode performance and enabled the selection of the most suitable “SPA” structure, based on resistive protective elements. Summarizing the economic benefits to copper electrowinning tankhouse operation with De Nora’s self- protected all DSA® anodes are; Double-digits power savings Cobalt-free electrolyte operations Minimal dendrite shorting damage incurred at the SPA anode Smoother, uniform cathode deposits with tangible improvement on current efficiency Tankhouse operations producing lead-free copper quality cathodes, in addition to elimination of lead waste for improved operator health and environment. INTRODUCTION De Nora’s engineered “Value Technology Package” (“VTP”) for electrowinning, consisting of our DSA® anodes coated with mixed metal oxide specifically formulated for copper electrowinning in conjunction with an advanced self-protected full titanium anode (“SPA”), underwent an intense field qualification program, inclusive of the behavior under massive short-circuits as part of the field investigation, with the goal to select and appoint the ultimate design configuration of “SPA”. Optimized wireless-based monitoring system was included in the field program, demonstrating good functionality for cell parameters monitoring and remote shorts detection.

Jan 1, 2019

By Scott Beer

What New Technologies Will Drive Economic Improvements? ??Historical ?1060?s: Mainframe Technologies ?1970?s: Mini Computing ?1980?s: Workstation Computing ?1990?s: Personal Computing ?2000?s: Network Computing Internet PDAs Cellular phones ??What?s the next technology improvement? ??What?s next for Mining?

May 1, 2009

By Robert H. Clark

Introduction During the last twenty years, science and industry have been strenuously endeavouring to discover new sources and new kinds of liquid fuels and to work out suitable chemical methods for their production. One of the new possibilities for the production of liquid fuel on a large scale is law-temperature carbonization of various grades of coal. The use of alcohol as motor spirit, in spite of its relatively low calorific value, is being widely investigated. Its production by fermentation of sugars, its recovery from the sulphite liquors of the paper industry, its production directly from wood and also from calcium carbide, have all been considered. At present the most promising line of investigation would appear to be the further development of those technical processes which yield liquid fuels from coal; since science has shown the possibility of preparing all kinds of liquid fuels and even the complete conversion of coal into oils. The present paper will consider briefly: 1. The production of primary tar by low temperature carbonization of coal. 2. The hydrogenation of coal. 3. The synthetic processes of Dr. Franz Fischer.

Jan 1, 1928