Search Documents

By R. L. Christie

"THE ISLANDS lying north of the Canadian mainland, and the large Boothia and Melville peninsulas, form one of the great archipelagos of the world; this sparsely vegetated and nearly unpeopled region extends about 1,500 miles east to west and 1,200 miles from the mainland to the northern tip of the northern-most island. Sea access to most of the islands is restricted by ice to the summer season, and the 'polar pack' ice of the Arctic Ocean presses the year round against the northwest margin of the archipelago. Although the region is remote, the accessibility has greatly increased through a network of weather stations, airfields and air routes connecting with southern centres.The area considered in this paper is that part of the island region underlain mainly by sedimentary rocks. In broad terms, this includes the land and sea areas of the archipelago and the adjacent continental shelf, but excludes the dominantly 'Shield' terrain of Baffin Island, and of Melville and Boothia peninsulas. An impression of the size and potential of this sedimentary region may be gained by comparing some areas: the land area of islands underlain mainly by sedimentary rocks is over 300,000 square miles or about 50,000 square miles greater than the area of Alberta. The total area of the region, including the continental shelf and the inter-island areas, may be double this figure, and may approximate one-seventh of the land area of Canada."

Jan 1, 1970

By S. Minamiguchi

Grain refinement is effective to enhance strength and ductility of metallic materials. However this advantage has not been utilized fully for magnesium alloys in industry because microstructure control through thermomechanical treatment is difficult owing to their poor deformability. The authors proposed a high-speed heavy-reduction rolling for production of Mg alloy sheets. It was found that the deformability is significantly improved at high speed and that the thickness can be reduced 60% by one-pass operation even at room temperature without fracture at the rolling speed higher than 1000 m/min. In this study, commercial AZ31B sheets were rolled at 2000 m/min between room temperature and 350°C, and quenched immediately after the rolling. The sheets rolled at 200°C show the finest recrystallized microstructure with the mean grain size of 2.2 Rm. They show outstanding mechanical properties with the tensile strength of 293 MPa, and the elongation of 25%. It is concluded that high-speed rolling is very advantageous for grain refinement and improvement in mechanical properties as well as deformability and productivity.

Jan 1, 2006

By Marc C. Betournay, John E. Udd

"In this study, the authors investigated the stabilities of slopes cut predominantly into Trenton limestone in a large quarry in the Montreal region. Analyses of the bench and pit walls indicated that small-scale toppling, ravelling, and wedge failures are the most likely modes of instabilities. Because most of the joints dip steeply, however, the conclusion was made that relatively high walls could probably be justified.The field investigations were supplemented with the determinations of the shearing strengths of artificial discontinuities that were cut into samples of the limestone. The properties of a fine-grained limestone were found to be influenced very much by the magnitudes of the loads that were applied, while the properties of a crystalline limestone were found to be much less, or not load-dependent.The study is one of a number that are being conducted in this area.IntroductionExtensive quarrying has been done in the sedimentary strata of the Montreal area for a very long time. By any standards, it can be said that the Island of Montreal is a major mining area. At present, approximately 20 quarries are being operated in, or near, the city of Montreal.In addition to the millions of tons of limestone that are removed each year, a large number of excavations for foundations are cut into the sedimentary rocks.To date, however, very little information has been published concerning the engineering properties of the local geological materials. No mention is made of this aspect in the references which are presently available.Because of this lack of information, the senior author has initiated a study in which the strength properties of most of the rock types, and of the natural discontinuities contained in these, would be investigated. To date, the results of one other investigation have been published and other work is in process. It is hoped that the end result will be a comprehensive knowledge of the important strength properties of all of the rocks in the entire region."

Jan 1, 1983

By A. I. A. Salama, M. W. Mikhail

"The existing methods of block diagram manipulation and vanishing variable for flowsheet simplification used in coal and mineral processing circuit evaluation and optimization cannot be easily implemented on digital computer.The signal flowgraph technique is proposed to represent and simplify determination of the relationship between intermediate or end variable and the feed in the flowsheet. Typical and existing circuits are used to demonstrate the application of the proposed technique which can easily be implemented on digital computers.IntroductionRecently there has been much interest in the analysis and optimization of coal and mineral processing circuits to assist in the pre diction of coal and mineral processing plant performance. The block diagram and the vanishing variable were introduced and utilized in the analysis of plant flowsheet. Although the block diagram approach is useful, it requires manual manipulation of the circuit block diagram which may present difficulties in the situation of complex circuits. Moreover, it may not be easy to implement on a digital computer.In this paper, the signal flowgraph technique is proposed to represent the circuit flowsheet and to simplify the determination of relationships between intermediate or end variables (fractional mass) and the feed for any coal and for any mineral processing circuit comprising size and density separators. These relationships are utilized in the analysis and/or optimization of the circuit. The proposed technique is illustrated by considering typical and existing circuits."

Jan 1, 1987

By Earl T. Hayes

This paper briefly reviews the laws enacted in the United States governing the coal miner. It discusses amendments to the Coal Mine Safety Act and describes the provisions of the Metal and Non-Metallic Mine Safety Act.

Jan 1, 1969

By H. Sahay

"DISCLAIMER NOTICEThe views and conclusions contained in this presentation are those of the author and should not be interpreted as necessarily representing the official policies or recommendations of the Department of Mines and Energy, Government of Newfoundland and Labrador. ABSTRACTThis paper describes the main testing procedures that should be carried out to evaluate the capacity and capability of the service brakes on the large-size diesel-electric trucks now in common use at open-pit mining operations. Brake testing programs in general are described, and then consideration is given to different techniques of service brake testing, brake performance evaluation, braking energy and typical performance characteristics.IntroductionThe first diesel-electric truck with a capacity of about 85 tons was introduced in 1963 by Unit Rig and Equipment Company of Tulsa in cooperation with General Electric Company, who successfully developed and supplied the most important component- motorized wheels. Since then, its popularity and numbers have continued to grow, and now more than 3700 such units are in operation in mines around the world. In Canada alone, their number is more than 700, including about 150 in the Province of Newfoundland and Labrador. Similarly, their size has also grown from that initial capacity of 85 tons to 350 tons.Although the introduction of the electric trucks proved to be invariably economical, their indiscriminate use was not without severe consequences. Many runaways and even fatalities occurred when the dynamic retarder failed while the truck was travelling loaded down severe grades. The service brakes in such cases proved incapable of stopping runaway trucks, mainly due to their limited capability and the fading caused by excessive heat produced during the act of braking itself. This eventually led the various governments, the open-pit operators and the manufacturers to seriously question the braking capability as well as function of both service brakes and dynamic retarders. Extensive testing"

Jan 1, 1980

By C. A. Roloff

Demands for increased grinding production, lower-grade are and limited capital have resulted in ever larger grinding mills, some as large as 36ft (/1 m) in diameter and 12,000 hp (8,950 kw). The result is often f ewer machines per plant, with a greater dependence on each machine. To meet these reliability requirements, manufacturers of mills, drives, castings and other components have had to be innovative and creative in their design. Only by thorough review of past designs and practices and by model studies confirmed in field tests can the manufacturer have full confidence in the product. Because of the great interest in large mills, a short review of larger machines is presented. This discussion covers material feeding, bearings, the rotating element, drive trains and material discharge.

Jan 1, 1979

By Z. Tang

A collaborative project was performed between NRC Institute for Fuel Cell Innovation and MagPower Systems Inc, to develop a cost effective fabrication process to manufacture the anode for magnesium-air fuel cell with improved performance. A novel fabrication process was developed, which resulted in a porous microstructure with increased surface area, instead of the traditional solid structure. This porous anode greatly increased power density in the magnesium-air power source. This fabrication process is very simple and cost effective. Especially, this process makes it convenient to incorporate different alloying additions, as well as hydrogen inhibitor and electrolyte management additive into the anode. The anode composition was designed so that micro galvanic cells were formed as current is drawn out of the fuel cell, and resulting increased dissolution rate of Mg. It is feasible to incorporate hydrogen inhibitor and electrolyte management additive into the porous anode, and the anode with some kinds of inhibitors exhibited improved electrochemical performance. This paper describes the microstructure and electrochemical performance of anodes with designated porous structure and alloying additions. Furthermore, quantitative kinetics analysis of the obtained I-V curves and electrochemical impedance spectroscopy were carried out to clarify the mechanism.

Jan 1, 2005

By P. Rocque, S. Talebi

Although the measurement of blast vibration close to the blasthole is critical to the understanding of rock fragmentation mechanisms and blast damage in the rock masses, limited experience for such monitoring exists. Because much higher vibration amplitude and frequency ranges are expected in rock masses close to an explosive charge as compared to far field vibrations, different problems from those for the far field monitoring must be considered for near field blast vibration monitoring. Currently, guidelines for design of the near field blast monitoring systems do not exist. This paper describes the development of an integrated technique for vibration monitoring close to a blast hole, including selection and installation of transducers, design of a monitoring system and signal recording. A densified cement was designed for grouting accelerometers in order to match p-wave impedance between the rock and grout. The monitoring technique described has proven suitable for blast vibration monitoring within 2 m to 15 m of a blast hole having loading conditions similar to production blasts.

Jan 1, 1993

By L. Hutton, S. W. Colley

"The release of soluble salts of base metals from acid mine pits and in the waste water from metal refiners is an avoidable source local pollution and contamination. Tightening of the regulations controlling natural resource extraction and industrial wastewater discharge is mandating the removal and recovery of metals from waste streams, and the remediation of contaminated sites. There is an economic incentive in recovering the valuable copper and nickel, as the value of the recovered metal can offset remediation costs and for high flow waste streams can be a source of income. Extraction of metals from waste streams by conventional Ion Exchange and chelation resins is widely practised, but has limitations on applicability in complex and dilute feeds due to the structure and properties of polymeric resin beads. Composite Advanced Ion Exchange (AIX) materials have been developed for the recovery and purification of base metals from base metal mining and metal processing industries. A silica-composite based resin has been developed for the selective extraction of copper from high iron containing feeds. This resin can be eluted with sulfuric acid yielding a copper stream suitable for return to solvent extraction or to electrowinning. We describe the development and application of the resin and process to two acid mine drain feeds of varying copper and iron concentrations, and show that the copper concentration can be considerably upgraded even at small scale with a final metal content of >95% copper.INTRODUCTIONWaste water with high sulphate concentrations, low pH and containing complex and variable mixtures of metals is an inevitable product in the mining, extraction and metal refining industries. One problematical water source is Acid Mine Drainage (AMD) which in addition to the metals of interest also contains a wide range of contaminating elements. Purge streams from metal refining are less complex in composition but contain significant quantities of the value metals. The typical treatment of such waste streams is treatment with lime to increase the pH of the water, precipitating the dissolved metals and sulphate as a sludge of mixed metal oxides/hydroxides and sulphates. The process is effective in producing a water stream that can be safely discharged but if there are significant concentrations of value metals such as copper, nickel, zinc then there can be a considerable loss of metal value."

Jan 1, 2016

By Philip Thwaites

"Automatic flotation control in varying degrees of sophistication is practiced at a number of concentrators throughout the world. Practically, the variable conditions in the flotation circuit and the difficulty in maintaining accurate instrumentation information all add to the complexity of automatic control.Further development at the Kidd Creek concentrator has resulted in a 3075 mtpd copper flotation circuit capable of running twenty-four hours a day under the direct control of an optimizing supervisory computer.Three main streams, continuously monitored by an XRF analyzer, supply circuit information to the optimizing computer. Circuit efficiency calculations (from smelter contract terms) and target setpoints allow the computer to determine the economic optimum direction to move the circuit based on the grade/recovery relationship. Circuit manipulation is accomplished by precise pumping of collector and frother reagents together with accurate control of flotation bank pulp levels. The former uses computer controlled diaphragm pumps and the latter is achieved by control loops utilizing a float type level transmitter, variable position dart plugs and a process computer working to setpoints determined by the optimizing computer.The development of a fully automated flotation circuit is by no means complete, but increased knowledge and major hardware improvements have allowed its progression to a higher level of sophistication.IntroductionThe Kidd Creek concentrator is located twenty-six kilometers east of Timmins, Ontario, within a metallurgical complex including a 109,000 mtpy zinc plant and a 59,000 mtpy copper smelter and refinery. The concentrator treats two ore types, a copper-zinc ore and a copper-silver-Iead-zinc ore, at a combined rate of 4,500,000 mtpy. Flotation of the crushed and ground ore yields copper and zinc concentrates from the copper-zinc ore and copper, lead and zinc concentrates from the copper-silver-lead-zinc ore."

Jan 1, 1983

By John E. Callahan

"A stream sediment geochemical survey covering an area of 13.000 sq. km near Churchill Falls. Labrador. was conducted for Brinex (British Newfoundland Explorations Ltd.) prior to partial flooding by the Churchill Falls power project. Stream sediments (minus 80-mesh) were analyzed for Cu, Pb, Zn, Ni, Ag, Mo. U and Mn, and the heavy mineral, nonmagnetic fraction (minus 60-mesh) for Cu, Pb, Zn, Ni, Ag, Mo, Ba and Mn. A binocular examination of the concentrates for sulphides and pyrope garnet was done on the heavy mineral concentrates. The concentrates were also examined for fluorescent minerals.Two distinct areas with high trace-element values indicate the need for follow-up studies. The first is in an area of gabbro erratics containing massive and disseminated sulphides (pyrrhotite, pyrite and minor chalcopyrite) on the western edge of the survey area along the Esker Road. The second, largest area (several hundred square kilometres) is anomalous in U and Mo and associated with felsic intrusives (Red Wine Complex?), syenites. granite gneiss and sedimentary rocks (Seal Lake Group?).The binocular study showed that almost 15% of the heavy mineral concentrates contained pyrite and no other sulphides. This indicates that this technique may be worthwhile in determining the presence of sulphide minerals in stream sediments from glaciated environments. The only fluorescent mineral observed in the study was zircon."

Jan 1, 1981

By Derek E. McBride

"Exploration work in the Beardmore - Tashota area has led to a reinterpretation of relationships between gold mineralization and the geologicalevolution ofthe area. The host volcanic rocks form two parallel volcanic belts connected by a much smaller cross-cutting band, which trends northeast from Beardmore to Tashota. This connecting band consists of mafic and felsic volcanic, plus clastic sedimentary rocks in a sequence conformable with the contact of the Onaman Lake Batholith to the east. A metamorphic aureole or incorporated xenoliths are lacking along this major contact and the only intrusive relationship observed is chilling between mafic dikes and a cold host granite in proximity to it. Granite dikes are totally lacking in the volcanic succession, or the overlying sedimentary sequence. A major part of this sequence consists of a polymict basal conglomerate with granite boulders and volcanic clasts in a fine-grained chloritic matrix. The nearest source for these boulders is the Onaman Lake batholith.Gold mineralization in significant economic quantities (+ 50 000 ounces) occurs at the top or above the mafic volcanic succession as quartz bands. In the Northern Empire Mine, the band is conformable, folded, boudinaged and the mineral zoning shows a relationship to variations in the host rock, not structural overprinting. In general, where the host mafic tuff is medium-grained, the quartz band is thicker, up to a metre wide, and carries economic grade; where the tuff is finer-grained and bedded, the band is very thin and low grade.Stratigraphic control and metal zoning shows that the mineralization formed as part of the development of the volcano- sedimentary succession. The other major deposits in the area (Leitch and Sturgeon River) have a similar structural history suggesting that they are also syngenetic in terms of the stratigraphic development. Regionally, these deposits were emplaced prior to any significant tectonic deformation but at the end of the mafic volcanic event.The mafic activity was related 10 a period ofextension which caused the volcanic troughs to develop along centres of rifting. The hiatus at the end of this event permitted extensive hydrothermal systems to form and deposit siliceous exhalite bands within sedimentary or terminal mafic volcanic environments in promixity to major thermal sources. Subsequently, the Kenoran Orogeny deformed the entire succession into upright folds with a sub-vertical schistosity. Evidence shows that the deposits have remained intact since deposition."

Jan 1, 1987

By Pierre O'Dowd

"The southern Abitibi Belt is the major source of gold in Quebec. Although the northern part of the belt is quickly being developed, the area under study will not be downgraded in the near future because it still contains more than 75% of the known reserves in the belt.Gold is found in a variety of geological environments which are part of a small number of distinct structural patterns. For the exploration geologist, outlining such patterns might be easier and more productive than defining, when it is possible, the exact genetic nature of the gold mineralization.Exploring in the right place has always been one of the main concerns of explorationists. This paper briefly describes the various favourable geological settings, and outlines areas, types of structure and lithologies of high potential for gold exploration in the southern Abitibi Belt.IntroductionThe southern part of the Abitibi Belt is a profilic mining area for precious and base metals (Lulin 1990). Although mineralizing processes and controls of polymetallic deposits are well known and understood (Lydon 1984), almost every gold occurrence is a unique case and numerous models have been proposed (Roberts 1987; Hodgson and McGeehan 1982; Hodgson 1990).This study does not define new genetic models for the formation of gold deposits, neither is it meant to elaborate on the existing ones. A genetic approach, is by definition, theoretical and, to some extent, universal. It helps geologists define types of targets and exploration tools but does not outline or quantify target areas. To tentatively summarize the complexity of a genetic approach, a brief discussion on the various genetic models in vogue in Abitibi and the problems related to their use in exploration can be found at the end of this paper."

Jan 1, 1991

By M. Fairclough, B. Moldovan

Insights into uranium mining projects of the future can be gained by a careful statistical analysis of past and present deposits, as well as an examination of recent trends for uranium resource evaluation and primary uranium production. The International Atomic Energy Agency (IAEA) provides the necessary data and corresponding mechanisms as inputs for methodologies that enable strategic and scientific evaluations of long-term security of supply uranium required to sustain the demand for nuclear fuel. Sustainability of the uranium mining industry and subsequently new uranium mines of the future requires innovation and expertise to lower operating costs, maintain or improve uranium recovery while meeting the requirements of stakeholders in regard to protection of the environment and safety of the workers and general public.

Jan 1, 2020

By A. C. Headon, K. W. Lam, D. P. Dautovich

"Microbiological activities affecting the performance of materials have been encountered in diverse situations within Ontario Hydro. Case histories of bacterial problems which are presented include ground rod corrosion at transformer stations, corrosion of a bare steel cooling water intake structure in Lake Huron and corrosion of steel components in a nuclear generation station vacuum building. Possible microbiological activities which may affect the corrosion behaviour of containers for the disposal of nuclear fuel waste in the future are discussed, as are bacterial actions suspected of causing an odour problem in residential water heaters.IntroductionBacteria are ubiquitous. Except by use of sterilization methods, bacteria -free environments are no t possible to find. Bacteria lie dormant in hostile environments, spread easily through air and water currents and reproduce rapidly under favourable conditions. Although different types of bacteria have different preferable conditions for growth, they are highly adaptive and in general, whenever there is a source of water and carbon (carbon dioxide or organic matter), there will be bacterial activities . These activities often induce or enhance costly metallic corrosion in industries and water odour problems in rural water supplies . Underground structures and systems in contact with natural water or water containing organic matter are most susceptible to bacterial attack.The types of metal-degrading bacteria , their characteristics and the conditions for growth have been reviewed extensively in the literature(1,2,3). There are several often encountered groups of bacteria which, through their metabolic processes, may lead to the degradation of metals. A large variety of bacteria produce corrosive in organic or organic acids as waste, such as the well known formation of sulphuric ac id by aerobic sulphur oxidizers . Anaerobic sulphate reducers produce hydrogen sulphide which is corrosive and has an obnoxious smell, slime-forming bacteria from slime which shelters sulphate reducers and iron bacteria oxidize ferrous to ferric ion which precipitates as hydrated oxides creating oxygen concentration cells . The following are bacterial problems encountered in Ontario Hydro. Although the number of recognized cases has been few, they show the diversity of location and environment where bacterial problems could arise. These include ground rod corrosion at transformer stations, corrosion of bare steel in a water intake structure, corrosion of steel in a nuclear generation station vacuum building and an odour problem in residential hot water tanks. In addition, possible bacterial- enhanced corrosion in containers for future disposal of nuclear fuel wastes are also discussed."

Jan 1, 1984

By I. Westermann, K. Marthinsen, M. S. Remøe

"Al-Mg-Si alloys often add small additions of e.g. Mn or Cr, to form dispersoids, which may act as nucleation sites for Mg2Si particles after homogenization. The purpose is to ensure a high density of uniformly distributed small ?’-particles, which can be dissolved during further processing prior to the final age hardening step. However, their density and spatial distribution are critically dependent on the homogenization procedure. It is therefore important to have a robust and reliable method for assessing their spatial distribution. In the present work an existing methodology for assessing spatial uniformity, the Global Shannon Entropy (GSE), has been implemented and evaluated for different dispersoid structures characterized by scanning electron microscopy. This metric is highly dependent on the parameters used, but by careful selection of adequate parameters, it can be effective in detecting non-uniformity. An important weakness with the GSE was identified, and a modification to improve on the ability to differentiate degrees of non-uniformity is suggested. To evaluate the proposed methodology, the effect of heating rate on dispersoid precipitation behaviour during homogenisation of four Al-Mg-Si alloys with different Mn/Cr-content has been investigated. The metric with the new term has demonstrated promising results, and improved the ability to differentiate degrees of spatial uniformity.INTRODUCTION Al-Mg-Si series alloys are the most common aluminium extrusion alloys and are attractive for applications in a range of sectors (e.g. construction, automotive and recently also in consumer electronics), due to their generally good combination of strength, ductility and corrosion resistance. However, their extrudability and end properties depend critically on the alloy chemistry as well as prior processing conditions. Coarse ß-AlFeSi or Mg2Si-particles typically have a detrimental effect on extrudability, while small dispersoid particles may affect recrystallization, grain growth and precipitation of Mg and Si. The strengthening potential in the final age hardening step depends strongly on the amount of Mg and Si in solid solution after extrusion. The manner in which these particles are spatially distributed will decide whether the final product will exhibit uniform properties, and the number density and sizes will determine the extent of the effect. As such, these are important characteristics."

Jan 1, 2018

By Owsiacki. Leo

Both the 8 and A-C ore zones of the Heath Steele Mine contain extensive areas of brecciated ore. This texturally distinct ore type has been tentatively defined as a fragmental or conglomerate massive sulphide. It consists of subangular and round fragments of pyrite up to 30 em in diameter, smaller quartz clasts and chloritized, mineralized, lithic fragments in a faintly banded matrix of pyrrhotite and chalcopyrite. The chalcopyrite is concentrated in the pressure shadows of the fragments and appears to reflect remobilization and recrystallization during a deformation which postdates the formation of the clasts. A generally conformable relationship with the underlying banded pyrite-sphalerite ore, discordancy with the host banded argillites, spatial distribution and similarity to Kuroko ores suggest that the fragmental ore is of primary origin and that breccia formation is probably due to soft-sediment slumping or sliding initiated by volcanic explosions, as hypothesized for similar massive sulphides in various Japanese mines. It is nevertheless recognized that certain structural features in some clasts may result from deformation preceding the formation of the breccia, and at this stage a tectonic origin cannot be completely eliminated.

Jan 1, 1979

By J. G. Whellock, J. W. Matousek

"In spite of their importance to the economics of many metallurgical projects, the values and technical aspects of precious metals losses in smelting operations are relatively undeveloped subjects. This paper attempts to provide a condensed overview of precious metals losses in pyrometallurgy, using some of the limited production and experimental data available. It is intended for three general groups of metallurgists - operators attempting to improve recoveries, cost-accounting engineers making estimates of metal losses in new or modified smelting plants, and research engineers and students.Distribution coefficients of precious metals, the ratios of metal or matte assays to slag assays, are convenient means of comparing smelting processes and the tendencies of the different metals to enter the slag. For silver in lead blast furnaces this ratio is approximately 250;for gold and the platinum group metals in submerged-arc, electric furnaces it is 900. The ratio for gold and PGMs in converters varies with the degree of oxidation of the charge. The over-all cycle-average for industrial installations is tentatively estimated to be 35.IntroductionThe magnitude of precious metal s losses in pyrometallurgical operation s is difficult to assess. The primary producers are generally reluctant to discuss the subject. The by-product producers (the large sulphide smelters o f copper , nickel, and lead) might be more willing to disclose information, but these have precious metals in their feeds in such dilute quantities that accurate accounting is extremely difficult. It is not until numerous processing steps have been taken t hat the precious metals become sufficiently concentrated to permit acceptably accurate sampling and analytical procedures to be followed. Thus, knowledge of the precious metals contents o f the intermediate mattes and slags may simply be unavailable."

Jan 1, 1990

By W. H. Hastings

Introductory In the amount of her coal reserves, Saskatchewan ranks third among the provinces of the Dominion, with a total, as estimated by D. B. Dowling, of 59,812,000,000 tons. All the coal so far discovered in the Province is lignite, and it would appear unlikely that bituminous or higher grade coals exist. General Occurrence of the Coal The location of the coal-bearing formations in Saskatchewan is shown on the accompanying map. It will be seen that the areas lie principally in the southern part of the Province. The more darkly shaded areas indicate locations where development is taking place, or where coal-seams are known to occur, either through outcrops in valley-sides or through having been encountered during boring operations. The coal-seams are not necessarily continuous throughout the shaded areas, but in all pans of these there are coal possibilities. It is quite possible that small outliers of the coal-bearing formations may occur further north in the Province, but, generally speaking, coal is not likely to be found outside the shaded areas.

Jan 1, 1929