Search Documents

By C. S. Liao, S. L. Wang, C. H. Yan, F. X. Cheng

A significant development in the theory of countercurrent extraction will be presented in this article. A new term in countercurrent extraction process analysis, "Adjacent Stage Impurity Ratio" (ASIR), is proposed, and its expression is deduced. Furthermore, based on the term together with mass balance and extraction equilibrium, the conditions where a given countercurrent extraction separation operation can have minimum amounts of both extracting solvent and scrubbing agent solution can be estimated, and the equations of the two minimum amounts can be deduced. It was found that the equations for a two-component separation using a single aqueous or organic feed are exactly the same as they appeared in the theory initially established in the 1970s. Unlike its earlier version, the present derivation does not involve feed-stage-composition hypothesis, and also has the advantage of dealing with a double-feed system where both aqueous and organic feeds are simultaneously employed whereas the earlier theory can only analyze a separation using a single aqueous or organic feed.

Jan 1, 2014

By R. D. MacEchern, M. C. Rockwell

"This paper describes the research and tests carried out to recover the readily available barite from the tailings produced by the Nystone Chemical Ltd. operation at Debert, N.S. The tailings comprised 70-80% of the original feed and contained about 20-25% Baso4 .The objective of the research, undertaken during 1982, was to produce a barite concentrate which would meet the American Petroleum Institute (API) barite requirements for use in drilling mud. Samples from the tailings pond were examined and analysed to determine the tailings characteristics.Preliminary test work was performed on the tailings samples using a Haultain Superpanner, Wilfley tables and Humphrey's spirals. The grade of the barite concentrate retrieved did not satisfy the API barite requirements.The fineness of the tailings and the fact that approximately 80% of the barite was contained in the -200 mesh (0.074 mm) size fractions, indicated that flotation of barite from the tailings might be successful."

Jan 1, 1984

An optimization process is described that can be systematically applied by mine planners to produce life-of-mine schedules aligned with their strategic targets, while maximizing the net present value of the mining operation. The software tool employed uses heuristics and an evolutionary algorithm to generate life-of-mine schedules of production and development activities. Generating such schedules is typically a very difficult task due to the large number of operational constraints that must be respected, and the vast number of alternative schedules; as a result the value of the mining operation can be compromised. With an expansion at Newmont?s Leeville mine in Nevada, the mine planners were given the task of producing feasible life-of-mine schedules with significantly increased production rates. Their initial efforts indicated that it would be a considerable challenge to generate such schedules in a timely manner. By systematically applying the proposed optimization process, the mine planners were able to generate optimized life-of-mine schedules with the desired production rate.

Aug 1, 2013

By Steve Dismuke, Tom Diment

In December 1994, Polaris decided to investigate the use of cemented rockfill (CRF) to supplement the existing frozen rockfill system. Extraction plans for the remaining ore reserves required a backfill with superior stiffness proper-ties and capable of developing high early strengths. Although CRF has been used success-fully at several mining operations, there was the additional challenge of making a reliable cemented product in permafrost conditions. There was also the challenge of procuring and storing one year’s supply (13 000 tonnes) of bulk cement. By the spring of 1995, following three months of research, test work and process design, the decision was made to proceed with the procurement and construction of a 3000 tpd batch plant. An ambitious completion date of December 1995 was set. Team Manufacturing of Langley, British Columbia was awarded the contract, complete with the considerable task of having the batch plant fabricated and ready for sea lift shipment by August, 1995.

Jan 1, 1996

By R. Mohamad, J. Asfahani

Abstract - Radioactive characteristics of pits drilled in the Al-Sharquieh mine while prospecting for recent phosphatic resources have been investigated. The results indicate that phosphatic layers are characterized generally by high radioactive intensities (more than 800 c.p.s). The lithological section in the study area is very complex sedimentologically, and characterized by high faciological variation in all directions. The Schlumberger geo-electrical configuration with fine separation of AB/2 was successfully applied to determine lithological boundaries, and the resistivities of the layers of the lithological section, especially for thin layers. It was shown that the phosphatic layer resistivities increase or decrease as a function of associated material. As a result, two types of phosphatic layers have been geo-electrically distinguished. The first is characterized by high resistivity and relatively low radioactivity, which could be related to the rock phosphatic layers. The second is characterized by low resistivities and high radioactivity, which could be related to the sandy phosphatic layers.

Jan 1, 2000

By Michael Nicol

A quantitative description of hydrometallurgical operations depends primarily on an understanding of the kinetics of the chemical and physical processes that take place in such operations. This paper will review the current status of kinetics in hydrometallurgy in terms primarily of the author’s experience in diverse unit operations. A distinction will be made between the popular use of models based on limited kinetic data and mechanisms which reflect the actual elementary chemical or physical steps involved in an overall process. Several examples will be used to illustrate this distinction. The proliferation of published papers of declining quality has resulted in the bequest to later researchers of outdated and often incorrect conclusions by a process that is often difficult to reverse. Some examples of these mysterious concepts will be examined and hopefully reversed. Finally, several examples will be given that identify significant gaps in our understanding of the kinetics of important processes that remain unresolved.

Jan 1, 2014

By Chelto. D. Smith

With the pressure on mine and metallurgical managers to take accountability for responsible corporate governance in their operational area, it is no longer acceptable to rely on central departments in the organization to manage safety, health and environmental impacts of the company?s processes. Environmental impacts exist because of the production or mining process. Some of the inputs to the process are natural resources and some of the outputs of the process are the inputs to the environmental control equipment, plant and the environment itself. Environmental management therefore needs to be incorporated in production management to effectively control and reduce the impacts. Many aspects of environmental management are identical to production management and the systems to manage them will likewise be very similar. By examining key components of these two management systems a decision can be made whether environmental management and production management are structurally similar and can be integrated into a combined IT solution.

May 1, 2009

The fracture behavior of second phase particles and the role of matrix material on the wear resistances of the three Al-Si alloys containing 8, 17, and 19% Si were investigated using single pass scratch testing technique by applying normal loads between 0,15 and 5,00 N, in ambient air, Optical microscopy and SEM with EDS were used to analyze microstructures and morphologies of scratch tracks of the Al-Si alloys, The results showed that needle-like Si particles fractured under a load of 0.50 N, while block-like Si particles fractured at loads above 3,00 N, The Al-17% Si alloy with large number of needle-like particles (area fraction 16,4%) exhibited the highest coefficient of friction (0,8) and the widest scratch track, The Al-19%Si alloy containing high Si percentage and larger number of block-like particles (area fraction 16%) exhibited the lowest coefficient of friction (0,37) and the narrowest scratch track width. Presence of block-like particles was effective in reducing the amount of material transfer from Al-Si alloy surfaces to the counterface.

Jan 1, 2005

By J. M. D. Wilson, W. Petruk, C. Coté

"The behaviour of minerals in the Mount Wright spiral circuit was investigated to find methods of improving iron oxide mineral liberation and recovery. The feeds, concentrates and tailings from rougher, cleaner and recleaner spirals in one mill line were sampled before and after the sizing screen openings were reduced from 2 mm to 1.6 mm. Sized fractions of each sample were analyzed with the MP-SEM-IPS image analysis system at CANMET to determine mineral quantities and liberation characteristics of the iron oxide minerals. Mass balance techniques were used to calculate stream recoveries of iron, silica, total iron oxide minerals, hema¬tite, goethite, quartz, ferromagnesian silicates, and liberated and locked total iron oxide minerals for each sieve fraction.The reduction of the sizing screen openings increased the ap¬parent liberation of the total iron oxide minerals in the screen undersize from 89% to 94% and raised the over-all iron recovery from 84.4% to 85.3%. Apparent liberation of iron oxide minerals in the cleaner sand also increased from 70% to 85%, but the – 75 µm fraction re¬mained the only fraction containing an acceptable amount of liber¬ated iron oxide minerals in each case. Due to limitations of spiral and grinding efficiency it is recommended that the cleaner sand be screened at 300 m, the +300 m fraction be reground, and the – 300 p.m fraction be rerouted to the rougher spirals.The amount of fine liberated iron oxide minerals (– 106 m) lost in the tailings was 46 TPH in mill line 3. This value represents 41 wt % of the free fine iron oxide minerals, or 7 wt % of the total iron oxide minerals in the spiral feed. Further work is needed to investigate the possibility of recovering this material by other methods.Middling iron particles (010 50%) and presumably free gangue in the size range –300+ 75 m tend to be recovered by spirals by entrapment."

Jan 1, 1990

By Craig H. B. Leitch

"In describing the alteration of porphyry systems, the term ""secondary K-feldspar"" appears to be an oversimplification. A better term would be ""alkali feldspar"" alteration, because in actual fact the replacement feldspars show gradational changes from an albite, which is important in some systems, to an alkali feldspar containing minor orthoclase molecule, to true orthoclase.There are several textural varieties of secondary alkali feldspar present in the porphyry systems studied from British Columbia, Australia and New Zealand. These include, in apparent increasing order of alteration intensity: clear albite (An10); patchwork albite (An5-10); chessboard albite (An0-10); ""irregular albite "" (An0Ab100 to Ab90Or10); untwinned ""anoralbite"" (Ab90Or10 – Ab70Or30); and orthoclase (Ab40Or60 - Or100)·The exploration significance of these varieties of alkali feldspar is that their gradation in composition, from sodic to potassic, may be linked to a corresponding increase in intensity of alteration. Thus, there is a tendency for more sodic alteration feldspars to characterize weak, sub-economic deposits, or the fringe zones of stronger deposits; the more potassic alteration feldspars may provide an exploration vector toward more highly mineralized zones."

Jan 1, 1981

By Craig H. B. Leitch

"In describing the alteration of porphyry systems, the term ""secondary K-feldspar"" appears to be an oversimplification. A better term would be ""alkali feldspar"" alteration, because in actual fact the replacement feldspars show gradational changes from an albite, which is important in some systems, to an alkali feldspar containing minor orthoclase molecule, to true orthoclase.There are several textural varieties of secondary alkali feldspar present in the porphyry systems studied from British Columbia, Australia and New Zealand. These include, in apparent increasing order of alteration intensity: clear albite (An10); patchwork albite (Ab5-10); chessboard albite (An0-10) "" irregular albite "" (An0Ab100 to Ab90r10); untwinned "" anoralbite"" (Ab90Or-Ab70Or30); and orthoclase (Ab440Or60-Or100)·The exploration significance of these varieties of alkali feldspar is that their gradation in composition, from sodic to potassic, may be linked to a corresponding increase in intensity of alteration. Thus, there is a tendency for more sodic alteration feldspars to characterize weak, sub-economic deposits, or the fringe zones of stronger deposits; the more potassic alteration feldspars may provide an exploration vector toward more highly mineralized zones."

Jan 1, 1981

By M. K. Gangal, A. E. Hall, S. B. V. Stewart

"An investigation into the problem of atmospheric fog in Canadian mines is described. Fog occurs in several mines and the reduced visibility can result in the closure of workings for safety reasons. Information on the mechanisms of fog formation are discussed and the methods for improving conditions are reviewed with their relative costs.INTRODUCTIONAtmospheric fog occurs in several Canadian mines during spring and summer. The fog which reduces visibility, contributes to loss of production and increased accident risk . Closure of ramps in mechanized mines causes mining to be stopped or rescheduled, and stoping and grade control may be affected . Increased corrosion of equipment may result from acidic fog .Fog is commonly caused by saturated air being compressed and heated by an inlet fan and then being circulated in an ascensional system with heat transfer to the walls of wet airways. This causes supersaturation and water droplets condense to create fog, with liquid water contents of 0.5 g/kg to 3 g/kg of air. These concentrations reduce visibility to less than 10m and prevent mining. Less severe fog is usually tolerated as a nuisance, about which little can be done."

Jan 1, 1989

By K. Kawagishi, J. Ang, A. Sato, H. Harada

"We have recently proposed a new ""EQ Coating"" bond coat system to solve the problem of secondary reaction zone (SRZ) formation caused by bond coats applied on the hot section components of modem jet engines. A viable EQ coating alloy was previously found for a representative znd generation superalloy, TMS-82+. It would be ideal if the same could be done for a representative 5th generation superalloy, TMS-173. In this paper, we will show that the coating with the best oxidation resistance in the EQ system of TMS-173, although possessing considerably better resistance than TMS-173, did not have sufficient oxidation resistance. In order to improve the oxidation resistance of the EQ coating for TMS-173, we have ventured into ""Pseudo-EQ coatings"". A diffusion couple between the Pseudo-EQ coating and TMS-173, after 300hrs at 1100°C, had a 0-15µm IDZ, but no SRZ. A diffusion couple between a conventional coating and TMS-173 formed a 80-150 µm SRZ. After a 1 hr oxidation test at 1100°C, the PseudoEQ coating formed a thinner oxide layer than the EQ coating, but still contained NiO and spinel. Aerospace"

Jan 1, 2006

By Jan Drzymala, Przemyslaw B. Kowalczuk

Froth flotation is widely used for upgrading of ores and other materials. Efficiency of flotation depends on many parameters, including type, chemical structure and dose of flotation reagents. Selection of a proper frother in flotation depends on the material used, necessary dose of frother and its selectivity. The selectivity of flotation can be characterized by proper separation factors and indices. In this paper separation selectivity and power of frothers were evaluated basing on separation data for a given material and frother, plotted as the recovery of the useful component in the concentrate versus the recovery of the remaining components in the tailing. Such a plot is called the Fuerstenau upgrading curve. The selectivity was defined as the location of the whole upgrading curve in relation to no and ideal separation lines, expressed on the scale from 50 (no separation) to 100% (ideal separation). In turn, the flotation power was defined as the dose of frother to reach a certain upgrading level at which recoveries of the useful and unwanted components are equal. The power and selectivity of frothers were determined for the Kupferschiefer stratiform copper ore floated in the presence of a fixed amount of xanthate and varying doses of frothers using a laboratory flotation machine. Basing on the separation results for different poly(propylene glycol) (CnH2n+1O(C3H6O)mH, CnPm) and poly(ethylene glycol) (CnH2n+1O(C2H4O)mH, CnEm) alkyl ethers, it was found that the concentrate yield and recovery of copper as the useful component in the concentrate were greatly influenced by the type and dose of frother. However, the same results plotted in the form of the Fuerstenau upgrading curve clearly indicated that the selectivity of frothers was similar, while their power was different. It proves that both selectivity and power of frothers are useful parameters for characterizing flotation systems.

Jan 1, 2016

By James E. Rider

"Fractures in mine hoist drumshafts are rare. We know of no previously reported attempts to repair a fractured drumshaft; any feasible method would involve welding and the associated problems of distortion, crack formation and strength.In June 1984, a fracture was discovered in the drumshaft of the production hoist in the Teck Corporation, Lamaque Division Mine at Val d'Or, Quebec. Delivery time on a new shaft would have been at least six months. The shaft was repaired in ten days and the total out -of-service time was four weeks.This paper describes why the shaft failed, how it was repaired, and the special alignment procedures employed during re-installation to minimize stresses in the repaired area.IntroductionThe performance of a mine hoist drumshaft is absolutely critical to mine operation. An inoperable drumshaft means no hoist, which in turn means no production or mine operation.Fractures in mine hoist drumshafts are rare. Previously when they have occurred, no one has seriously considered attempting a repair because of problems involved. Any feasible method would involve welding, which raises several major problems - namely, metallurgical, alignment, and strength.In July 1984 this very situation occurred at the Teck Corporation, Lamaque Division Mine in Val d'Or, Quebec.It was recognized that a new shaft would take at least 6 months' fabrication and delivery time. However, having had some experience at repairing broken shafts in other machines under similarly desperate circumstances, and after due consideration, it was concluded that by applying the correct techniques and engaging the right expertise, it would be possible to perform a repair and have the mine back in operation within a month.Thanks to outstanding efforts by all, the repair was accomplished in ten days and total out-of-service-time was only four weeks. The causes of the failure were determined and the calculated stress levels confirmed by strain gauge measurement during operation.The success of this project was achieved by adhering rigorously to fundamental management and engineering principles."

Jan 1, 1988

By James E. Rider

"Fractures in mine hoist drumshafts are rare. We know of no previously reported attempts to repair a fractured drumshaft; any feasible method would involve welding and the associated problems of distortion, crack formation and strength.In June 1984, a fracture was discovered in the drumshaft of the production hoist in the Teck Corporation, Lamaque Division Mine at Val d'Or, Quebec. Delivery time on a new shaft would have been at least six months. The shaft was repaired in ten days and the total out -of-service time was four weeks.This paper describes why the shaft failed, how it was repaired, and the special alignment procedures employed during re-installation to minimize stresses in the repaired area.IntroductionThe performance of a mine hoist drumshaft is absolutely critical to mine operation. An inoperable drumshaft means no hoist, which in turn means no production or mine operation.Fractures in mine hoist drumshafts are rare. Previously when they have occurred, no one has seriously considered attempting a repair because of problems involved. Any feasible method would involve welding, which raises several major problems - namely, metallurgical, alignment, and strength.In July 1984 this very situation occurred at the Teck Corporation, Lamaque Division Mine in Val d'Or, Quebec.It was recognized that a new shaft would take at least 6 months' fabrication and delivery time. However, having had some experience at repairing broken shafts in other machines under similarly desperate circumstances, and after due consideration, it was concluded that by applying the correct techniques and engaging the right expertise, it would be possible to perform a repair and have the mine back in operation within a month.Thanks to outstanding efforts by all, the repair was accomplished in ten days and total out-of-service-time was only four weeks. The causes of the failure were determined and the calculated stress levels confirmed by strain gauge measurement during operation.The success of this project was achieved by adhering rigorously to fundamental management and engineering principles."

Jan 1, 1988

By J. Dufour

Although the recovery of nitric and hydrofluoric acids from stainless steel pickle liquors has been solved by several methods, such as solvent extraction, acid retardation, evaporation or pyrohydrolysis, metals (mainly iron, chromium and nickel) are usually obtained as a waste or by-product that has to be disposed. Alternatively, the treatment requires a high liquor flow to be economical, as is the case for pyrohydrolysis. A new process has been developed for metals recovery, that produces metal oxides with a low fluoride content. This new technique is based on a selective precipitation mechanism, which produces nickel hydroxide with a purity of 90%, separate from a mixture of iron and chromium oxides and hydroxides suitable for recycling. The reaction mechanism is based on the precipitation of fluoride compounds of iron and chromium, K2FeF5 and CrF3. For this purpose, free fluoride must be added as potassium fluoride. Also, solid fluoride compounds are hydrolysed, releasing free fluoride. A part of the fluoride is recycled to the selective precipitation operation and the remainder is fed to the acid recovery stage. Nickel does not react in this operation; it remains in solution giving a high separation yield.

Jan 1, 2006

By K. G. Markkola

Since 2005, Compafifa Contractual Minera Candelaria (CCMC) has defined various strategies which aim to optimize the usage of the available energy in each of the SAG grinding circuit modules (SABC-A configuration). For this purpose, the use of larger size balls along with operating with an optimum balls/load ratio has been implemented. Additionally, in the ball mills, the amount of balls in relation to the equipment's usable diameter has been optimized. In the pebble crushing circuit, the percentage of material passing 12 mm (112 in) product has been increased by 15% by: (1) modifying the crusher mantle profile, (2) implementing a strategy for maximizing the power in each crusher, (3) using continuous improvement tools (Lean - Six Sigma), (4) redesigning SAG mills discharge grates, and (5) changing discharge grates in order to control the crusher feed size distribution profile. All these activities have improved plant throughput by 1,000 t/d with no significant capital investment. As part of the energy consumption optimization study, we have considered determining the optimum operational rate of each SAG mill, in relation to the mill liner life and also the improving the control strategy in conventional grinding.

Jan 1, 2007

By C. Hari Manoj Simha, J. Gholipour, M. J. Worswick

Due to the high pressures involved in the hydroforming process, friction and lubrication play an important role and can affect formability of the material. Tubes of A1Mg3.5Mn aluminum alloy, of 76.2 mm (3 inch) outside diameter and 2-mm thickness were considered in this study. Three kinds of lubricants, Al070, Hydrodraw711 and water, were applied to the tubes and tubes were hydroformed to burst in a square shape die cavity. The key process parameters were recorded during the tests. An in-house Gurson-Tvergaard-Needleman (GTN) damage-based material model, implemented in LS-DYNA, was used to model the process and predict the formability of this material. The applied axial loads and internal pressures recorded during the tests were used in the computations. The effect of different types of elements (solid and shell) with different constitutive models (von Mises and GTN models) in predicting the strain distribution is studied. The GTN damage-based material showed a good ability to capture necking and displacement histories in this process. Both predicted and measured results showed that the lubricant with lower coefficient of friction can effectively increase the comer expansion.

Jan 1, 2006

By J. Sugai

Formability of extruded round AZ31 magnesium alloy tubes with different manganese concentrations was evaluated by performing bending tests and measuring strain along the length of the tubes during the bending process. It was found that an increase in the manganese content from 0.3 % to 0.7% did not exert any significant effect on the values of yield stress, elongation, or compression to fracture. However the hardness tended to increase and the UTS decreased. The compressive ductility was significantly lower than tensile ductility for all manganese concentrations. Consequently, the formability of tubes decreased, causing cracks in areas where compression strain occurred during bending. It was also found that a larger strain occurred in the latter half of the region along the length of tube between the clamp-end and the tube-positioning block. Within this region, alloy tubes with higher manganese concentrations, 0.5 and 0.7 %, there was a clear strain peak within the strain profile, while for the 0.3 % Mn alloy, a more uniform strain profile was exhibited, indicating a more uniform deformation. This was confirmed by microstructural analysis of the specimens.

Jan 1, 2006