Search Documents

By John E. Udd

The stability of a rock mass is influenced by the presence of discontinuities. In assessing stability, it is required that one should know the frictional and cohesive properties of these contained weaknesses. In the study performed by the authors, a number of samples of diamond drill core containing open discontinuities were tested in shear. The results obtained were compared with values which resulted from back analyses of instabilities in the field.

Jan 1, 1979

By P. Homola, M. Karlík, M. Slámová

"Aluminum sheets (AA1199, AA8006, and AA5754) were processed by accumulative roll-bonding (ARB) in the temperature range from 20 to 350°C. The microstructure of the sheets was characterized by means of scanning and transmission electron microscopy and electron backscattered diffraction. Mechanical properties were monitored by hardness measurements and tensile tests. Increasing strain (number of ARB cycles) led to incremental development of lamellar microstructure with a decrease of the spacing between high-angle grain boundaries in the normal direction of sheets. ARB process produced an important increase of strength while maintaining thickness and relatively high ductility, without accenting of the anisotropy of mechanical properties of sheets. The level of hardening decreased with the processing temperature and at 300 and 350°C ARB caused even the softening of the material due to the recovery of the deformed microstructure or partial recrystallization during heating to ARB processing temperature.INTRODUCTION Accumulative Roll Bonding (ARB) is a technique of grain refinement by severe plastic deformation (SPD) proposed by Saito et al. (1999). One ARB cycle consists in sheet cutting, surface treatment, stacking of two pieces, heating (optional), and rolling with 50% reduction in thickness. Since the sheet thickness remains unchanged by this cycle, ARB processing can be repeated as many times as desired. The goal of ARB is to impose an extremely high plastic strain on the material, resulting in structural refinement and strength increase without changing specimen dimensions. After several cycles, ultra-fine grained (UFG) materials with high strength and relatively high ductility are produced. An advantage of this method is that it does not require any special equipment as other SPD methods such as equal channel angular pressing (ECAP) (Valiev & Langdon, 2006), high pressure torsion (HPT) (Valiev et al., 2000), or cyclic extrusion and compression (CEC) (Richert et al., 1999), but only a conventional rolling mill and so it is seen as an economically viable and industrially scalable processing route. ARB processing has been successfully applied to various kinds of metallic materials at room or elevated temperatures (Tsuji, 2005). Besides processing single metals and alloys, ARB has also been used for creating ultra-fine grained and nanograined metallic composites (Wu et al., 2010; Qu et al., 2014)."

Jan 1, 2018

By Louis Tellier

SIDBEC commenced detailed planning of major capital expenditures to install integrated steelmaking facilities in 1969. Today, less than IO years later, SIDBEC and its subsidiaries have completed major mining, concentrating, pelletizing, direct reduction ? electric furnace steelmaking and continuous casting plants. The total cost of these projects was almost 1 billion dollars. The philosophy behind the project planning and the evolution of management control are explained. These extensive projects were undertaken during a period of exceptional inflation and a disturbed labour climate, but were nevertheless completed with only modest overruns, with good control of timetables and with exceptionally good start-up performance. Project planning, relations with consulting engineers, introduction of new technology, purchasing and field management and cost control are discussed.

Jan 1, 1979

By C. M. Acuna, M. Sherrington

In high temperature processes thermodynamic equilibrium is assumed and therefore chemical potential of elements, among the condensed phases, have to be the same. In such situation impurities distribute accordingly and their fractional distributions are affected by the masses of the coexisting phases. It has been claimed Teniente Converters perform quite well for smelting high impurity concentrates, especially in respect to volatilization and/or slagging. Production of high matte grade near white metal composition, requiring moderate oxygen enrichment in the process air, results in a huge mass of gas and therefore a high fraction of impurities report to it. Similarly, by recycling different sources of slag, flue dust or other materials, the mass of the final slag is increased and so do the masses of impurities reporting to the slag. Nevertheless, above a certain level the recycling of smelter byproducts is no longer feasible and the cycle has to be halted, unless higher impurity mattes are accepted. Although the process might be continued during converting and refining, lengthy and expensive measures have to be taken if suitable anode copper for electrolytic refining is to be achieved. In the present study samples of high arsenic matte grade and slag were obtained on a pilot scale. The matte samples, on the order 75%Cu, were equilibrated with slag at varying ratios in magnesia crucibles under CO/C02 atmospheres at 1523 K. After 24 hours equilibrium matte and slag were rapidly solidified and analyzed by copper, sulfur, iron and arsenic. Furthermore, industrial samples of matte and slag, in the order 75%Cu at 1523 K, were obtained via a special quenching sampling device to determine the association of copper and suspension of matte and copper in slag. Based on the results, the distribution coefficient of arsenic between slag and matte was evaluated along with copper species in slag and the fractional distribution of arsenic, in the coexisting phases, was determined as a function of the ratio mass of slag to mass of matte.

Jan 1, 2007

By W. Gan

The interactions between bitumen and quartz sands in aqueous solutions were studied with the objective of recovering residual bitumen from Athabasca oil sands froth treatment tailings. It was observed that the presence of various multivalent metal cation (Fe3-, Fe2+, Mg2+,Ca2+, etc.) increased the mutual coagulation between quartz particles and oil or bitumen droplets within certain pH ranges. While the increased coagulation was detrimental to the recovery of the bitumen since it lowered the degree of bitumen liberation from sands, this effect could be reduced or eliminated by the addition of organic chemicals such as citric acid, oxalic acid and EDTA. Among these organic chemicals, citric acid was found particularly effective even at very low concentration.

Jan 1, 2006

By Lorne Roberts

"This paper describes: how Falconbridge's fire protection system meets the needs of the Lockerby Mine; why the system was chosen over other alternatives; how it is unique, but can be applied to any underground situation; details of the system; how it was installed; the role of a fire protection company; and general considerations when choosing afire-suppresant system.IntroductionIn May 1981, after about three years of searching for the best fire protection system for the re-opened Lockerby nickel mine at Whitefish, near Sudbury, Ontario, Falconbridge Nickel Mines Ltd. installed an AFFF type of fire suppression system. It was designed and supplied by the Fire Protection Systems Division of Levitt -Safety Ltd.The system protects against loss of life, equipment and/or production, and it complies with legislation should fire occur in a fuel storage area and/or scooptram garage and service bay at any or all of the three levels near Shaft No.2.About 18 months after Levitt-Safety began working with Falconbridge, the system was designed and installed at a cost considerably less than that which would be incurred if fire damage caused the loss of two days of production.The fire protection system, which overcomes a limited water supply, is a self-contained balanced pressure proportioning system. It senses the flow and automatically determines the correct concentration of foam to water. It is triggered by a release mechanism which operates a bank of nitrogen cylinders, which in turn pressurize a pressure vessel to expel the foam concentrate and water from the tanks. This solution is piped to sprinkler heads in the specific area."

Jan 1, 1982

By R. C. Beard

"The Ontario Ministry of Natural Resources has recently initiated several incentive programs to encourage and facilitate the development of new mines in northwestern Ontario. Some are privatized out to consultants and contractors. The status of three of these programs will be reviewed in this paper.IntroductionOne of the main objectives of the Mineral Resources Group of the Ontario Ministry of Natural Resources is to encourage and assist mineral exploration and the development of new mines in the Province. Programs to accomplish this objective are largely carried out through two Branches in the main office (in Toronto), the Mineral Resources Branch and the Ontario Geological Survey, and also a number of regional field offices scattered across Ontario.The function of the Mineral Resources Branch is to identify and administer effective policies that will ensure maximum benefits to the Province from mineral resource extraction.One of the most important factors in ensuring effective exploration in the Province is the availability of a good geosciences data base from which to work. It is the responsibility of the Ontario Geological Survey to develop and continually update this data base, providing, to both the public and private sector, an inventory and analysis of the geology and mineral deposits of the Province.The main functions of the regional field offices are to provide technical data and advice to exploration companies and prospectors, to encourage and assist exploration, and to provide information and general assistance to producing and developing properties to facilitate resource development and extraction. This is accomplished through the offices of the mineral resource coordinators and resident geologists. In northwestern Ontario, these field offices are located at Thunder Bay, Kenora, Red Lake and Sioux Lookout.To accomplish their objectives, the Ontario Geological Survey and the regional field offices carry out regular, ongoing geoscience and other mineral resource programs, under their base funding."

Jan 1, 1982

By Alexandre Desbarats, Michel David

"All optimum pit design studies start from the geological are reserves inventory, the estimated grades of all blocks of potential are within the interpreted limits of the deposit. The actual optimization procedure is then carried out on block valuations based on these estimated grades. Thus, the relevance of any pit design can be seen to depend directly on the ore reserve estimation . To insure a proper pit design, a first step would be to use a geostatistical reserve estimation technique such as kriging, however, this is not enough. A frequently neglected fact is that the blocks of ore estimated during the planning stage of the mine are usually considerably larger than those on which the ore-waste selection will be made at the time of mining. Experience in the exploitation of large low-grade deposits has shown that large blocks, estimated to be are, when mined selectively in smaller blocks, often yield significant amounts of waste material. This phenomenon, known as internal waste, is a function of the variability of the grades, the size of mining unit and the amount of sampling information on which ore-waste decisions are made.In this study, it was proposed to consider the effect of internal waste caused by selective mining, on. pit design, using geostatistical methods to predict the tonnage and grade of recoverable reserves within large blocks.Optimum pits obtained using a block valuation formula taking into account the recoverable reserves within large blocks were compared with optimum pits obtained using a conventional block valuation formula. It was found that the optimum pits obtained by the proposed method had the highest total valuations and thus were, in fact, ""more optimum”. These pits were characterized by greater are tonnages at a lower average grade, the additional ore more than compensating for the drop in grade. It was also found that the consideration of internal waste in pit design could considerably alter pit limits in marginal areas of the deposit.It was concluded that selective mining had a significant, potentially critical, impact on the design of optimum pits especially in the case of large low-grade deposits."

Jan 1, 1984

By G. P. Gu

The in-service 90/10 cupro-nickel tubes in a water-chiller system suffered from severe corrosion damage during their relatively short service life causing unexpected down time. In addition to downtime, the environmental risk associated with losing refrigerant was also a concern that initiated this investigation, Microstructural investigation using SEM and electron microprobe indicated that pitting corrosion had resulted in local nickel depletion, During the corrosion process, copper appeared to have re-deposited around the corrosion pits accelerating the local corrosion.

Jan 1, 2005

By S. Dallaire

With the attainment of high temperatures it becomes possible to process any kind of material (particularly ceramics) in their liquid state. In the plasma spraying process, the material to be sprayed is rapidly heated until it is molten and is propelled by high velocity gases onto a surface where it adheres, to give protective coatings for a wide range of applications. The method could be considered as one of the most versatile and rapid to build up thick deposits (of plastics, metals, ceramics, cermets) and also free-standing artifacts for particular requirements without resorting to lengthy forming and sintering studies. Although plasma spraying is at the production stage in industry, advanced processes have also been developed for economically producing a wide range of new materials. This paper illustrates the benefits of the process and evaluates the challenges it represents.

Jan 1, 1987

By J. A. Espinosa-Guillen, J. A. Lopez-Molina, S. García, J. A. Valencia-Quintanar

"The design and implementation of grouting treatments in rock masses are procedures that require continuous adjustment of parameters and criteria to optimize the results. In this proposal we describe a set of tools that enhance decision-making for this type of jobs particularly in dam projects. The methodology is focused on hydrogeological zoning of the site and its constant update combining engineer’s experience with artificial intelligence techniques to integrate the site knowledge; as well as the evaluation of grouting results for different scrutiny scales, with special attention on the relationship between water absorption and grout consumption. INTRODUCTIONSeveral methodologies for design, implementation and evaluation for grouting rock masses have been developed for the solution of specific problems and tested in diverse geological conditions. Each of these methodologies is focused on results evaluation for different scrutiny scales (Table 1) and is employed to assist decision-making before or during the grouting process.Some methods define specifications for grouting each stage of the borehole, making theoretical, semi empirical or experience-based considerations to define basic parameters as maximum pressure, maximum volume, grouting time, flow rate, etc. Ultimately each approach aim to optimize the injection process, adjusting volumes or the grouting time required to obtain satisfactory results, reducing risk of creating new flow paths or unnecessary grout travels, and enhancing the mixture properties to achieve adequate penetrability and long-term behaviour. Some of these criteria have been widely used in dam projects, for example the concept of Grouting Based on Facts to define the maximum pressure and volume (Ewert, 1997), the GIN method (Lombardi & Deere, 1993; El Tani, 2012), or the North American standards based on Apparent Lugeon measures (Naudts, 1995; Bruce 2011); on the other hand, there are relatively new criteria that have shown good results for dam grouting as the Aperture Control Method (Bonin et al., 2012; Carter et al., 2012) or the Real Time Grouting Control Method (Stille et al., 2012)."

Jan 1, 2015

By P. E. Cavanagh

Abstract Many investigators have been interested in developing some non-destructive method for detecting or determining the changes in physical properties in steel occurring during endurance tests or normal service life of a part which fails in fatigue. This paper presents a broad discussion of some of this work and the possibilities of developing useful test procedures based on some of the information obtained in the past. Changes in magnetic properties, electrical resistance, damping capacity, X-ray diffraction patterns, and remaining fatigue life at load different from service load have all been investigated as possible means for following the sequence of events during fatigue failure. In some special instances, tests such as these may be used to predict fatigue failure. As an in stance of practical application of the continuous determination of changes in magnetic properties during fatigue, a brief account is given of work done in non-destructive inspection of mine hoist-rope. As a result of extensive experiments and field crisis, it has been found possible to detect the beginnings of failure in a wire rope in service. The test method used will detect plastic deformation in a wire rope, no matter what its cause. There is no possibility of determining the remaining useful life of a rope by calibrating changes in magnetic properties in terms of remaining fatigue life. A change in magnetic properties at a point in a rope may indicate a decrease or increase in fatigue life, depending on the overload history of the rope. A continuing change in magnetic properties ac a point, however, does reliably indicate a developing weak point which will eventually lead to failure. The important point about any change in magnetic properties is not the magnitude of the change, but whether or not it continues.

Jan 1, 1947

By Leslie McHattie, Sadek E. EI-Alfy

"The Maintenance Engineering Department at Carol Mining and Concentrating is currently in the process of introducing reliability concepts such as failure analysis, rework elimination, predictive maintenance, computerized maintenance history analysis, etc. to improve the over-all maintenance function in the mine and concentratormaintenance areas. Some current initiatives include:• Implementation ofan infrared thermographic scanning program.• Ultrasonic inspection of shafts for all critical equipment in the mine and concentrator areas.• Non-destructive testing of all major welds done by maintenance personnel.• Development of an effective vibration monitoring and analysis program for the production equipment in the mine (shovels, drills, haulage trucks, locomotives).• Failure analysis performed by maintenance engineers to identify the root cause of component failures on critical production equipment.• Computerized breakdown analysis to identify the recurring component failures which contribute significantly to high maintenance costs and production loss.• Implementation of a computerized maintenance management information system.This paper will outline the planned implementation ofthese initiatives, and others, and will also cover the status and results obtained to date."

Jan 1, 1992

By R. L. Eadie, J. L. Luo

The effect of plastic deformation on near-neutral pH stress corrosion cracking (SCC) also known as environmentally assisted cracking was studied by cracking rate measurements. All the tests were conducted in a synthetic near-neutral pH solution. The traditional potential drop tests using compact toughness (C-T) specimens with 2-3 mm long pre-cracks showed varying plastic deformation by rolling would increase the material's susceptibility to SCC. This was confirmed by cyclic loading tests using double notched flat tensile specimens with 200-300 µm long pre-cracks which gave the same results that the specimen with large scale plastic deformation by tensile loading had a relatively faster crack growth rate than that with only small scale plastic deformation.

Jan 1, 2005

By D. R. Schmitt, N. Ong, R. S. Kofman

Shales and mudstones comprise about 75% of all the sedimentary rocks. In, particular, organic rich shales are considered as a petroleum source rock and more recently with the advent of hydraulic fracturing technology to be a reservoir in their own right. In this sense, the aforesaid motivates our work with laboratory measurements of elastic properties of these geologic materials, which are known to be anisotropic. As such, assuming Vertical Transverse Isotropy (VTI) symmetry, the dynamic and static moduli of a series of cores from various geological formations in Alberta, Canada are simultaneously investigated as a function of confining pressure using the ultrasonic pulse transmission method and strain gages. Dynamic moduli were obtained from ultrasonic P- and S-wave velocities measured on a prism cut with faces perpendicular, parallel and oblique to the assumed vertical axis of symmetry. Static moduli were calculated from strain-stress curves obtained along the directions perpendicular and parallel to the assumed axis of symmetry as well. Velocity measurements show that samples are highly anisotropic, but that the pressure-dependent behaviour of the wave speeds differs. VP(90°) and VSH(90°) both with layer parallel propagation and polarizations change little with pressure while VP(0°) and VS(0°) (both with layer perpendicular propagation) display significant nonlinear responses particularly at pressures < 25 MPa. These characters transfer to the derived full set of elastic constants. In order to effect a proper comparison of the dynamic and static moduli, we convert the dynamic elastic constanst to linear compressibilities pependicular (Kdyn1) and parallel (Kdyn3) which are directly comparable to the static tangent compressibiities obtained by differentiation of the observed strains. Both sets highlight the anisotorpic nature of the material but most interestingly Kdyn1 _ Ksta1 but Kdyn3 > Ksta3 by nearly 40% for one of the samples. The other samples measured respond similarly suggesting that conceptually the structure of such materials could be considered to be constructed of alternating stiff or compliant layers. This finding has implications in the response of the formation to stress particularly during hydraulic fracturing and the interpreation of acoustic logs in providing appropriate measures of elastic properties for engineering purposes.

Jan 1, 2015

By S. M. Fatemi-Varzaneh

The AZ31 magnesium alloy is considered as a promising alloy in various applications and industries. Furthermore, to design a proper hot working process (rolling, forging and extrusion), the assessment of hot working behaviour of the alloy is necessitated. Accordingly, the hot deformation behaviour of AZ31 alloy was studied through hot compression testing method. The latter was carried out in a wide range of temperature (523 K to 783 K) and strain rates. The obtained true stress-true strain curves and final microstructures were examined and a partial melting was realized at 740 K. It was concluded that the presence of liquid did change the deformation mechanisms thereby affecting the flow behaviour.

Jan 1, 2005

By E. M. De Souza

"The mining industry has developed a strong need for monitoring underground openings since bulk mining, used for increased productivity, has become the dominant mining method industry wide. The large stopes associated with bulk mining methods generally have to remain open and stable for several months, and monitoring is essential to provide an indication of ground response to mining and stope stability. The instrumentation data is also important during design optimization, which is used to maximize recovery, to minimize the dilution of ore and to minimize costs. Monitoring is essential to implement safety and is also critical in stope and mining sequence designs. The safety related aspects of monitoring include the protection of underground workers and the prevention of accidents by providing early warnings of the onset of any ground instability. The design related aspects of monitoring involve the development of data bases used for stope dimensioning and mine sequencing and timing and the monitoring of ground behaviour as a result of mining to verify the validity of the design thus allowing for remedial action during operation.Manual instrumentation data collection is, in a number of cases, economically unfeasible and, in many situations, dangerous as instrumented areas become inaccessible or extremely unstable. Also, because more and more complex instrumentation is being installed in underground operations, in several cases it becomes practically impossible to collect readings manually. The design and development of low-cost acquisition systems for mine wide monitoring would thus constitute an important step toward automation in excavation instrumentation. A unique menu-driven automatic 32-channel analog data acquisition and analysis system with a built-in rock failure warning mechanism has been designed and developed. This low cost acquisition system is capable of receiving, processing, displaying and storing the transmitted instrument data remotely and automatically. Computer software has been designed to provide data reduction and analysis immediately in the field and to automatically display results in graphical form for quick interpretation. Automatic data interpretation is used to show trends in rock mass behaviour and the system can be used to provide early warning of rock failure to the mine personnel working in there so that immediate remedial action can be safely taken."

Jan 1, 1992

By D. Mu

A method is presented for evaluating the effective gas diffusion coefficient of porous media. A series of random-distributed porous solids with different porosity are generated, a solution of the gas diffusion equations inside the porous media is obtained using the finite element method (FEM), and then the effective gas diffusivities are computed. The results show that there is a percolation threshold sp, and this percolation threshold decreases with an increase in the connectivity of the pore network; the relationship between the effective diffusivity and the porosity is strongly nonlinear when the porosity £ is less than about 0.2; and is quasi linear for higher porosities. The threshold decreases with increasing the connectivity of the pore network. A formula relating the effective diffusion coefficient with porosity is proposed.

Jan 1, 2005

By P. Venkatasubramanian

"In recent years, computer based ""expert systems"" have been taking on large complex tasks for which no exact algorithmic solutions are feasible; tasks previously reserved for human experts requiring empirical knowledge, judgment, experience, developing a ""best solution "" by the use of plausible reasoning. Mining method selection is an appropriate area for the application of an expert system because extensive and detailed knowledge is required to make a ""best"" interpretaion of frequently ambiguous geological information. The expert system model presented here would enable users to apply expert knowledge to the evaluation of methods for coal deposits mineable by underground methods. IntroductionIn an increasingly complex and specialized world, human expertise spanning scientific, economic, social and political issues plays an increasingly important role in all branches of engineering. This is especially true of mining engineering. The number of scientific and professional disciplines involved in mine planning and evaluation, illustrates the problem. A conservative list includes geology, geophysics, geotechnics, hydrology, mining, environment, and economics.Engineers are almost obliged to be experts in at least one of the above disciplines if they are to handle the volume of information required in the planning process. Although computers have become indispensable tools in many endeavours, there is continued reliance on the human expert&apos;s ability to identify and synthesize these diverse factors, to form judgments, evaluate alternatives , and make decisions . This is especially true with regard to problems that are not easily amenable to precise formulations.The precious resource of human expert is also fragile and transient. The departure of a crucial expert from an organization ma y cause serious dislocations. Senior experienced people impart their knowledge of younger colleagues, but the demand for their talent may not leave sufficient time for such educational efforts. In recent years, computer based "" expert systems"" have been taking on large complex tasks for which no exact algorithmic solutions are feasible; tasks previously reserved for human experts, requiring empirical knowledge, judgment , experience, developing a ""best solution"" by the use of plausible reasoning."

Jan 1, 1988

By J. C. Thornley, H. L. J. Drummond

"Fifty years of wear on the original carbon steel shaft of this hydro turbine necessitated repair operations in 1980. Both austenitic and martensitic stainless steels have been used individually as journal materials in separate trials on an80-inch long and 22-inch diameter radial bearing but neither one nor the other has been successful.The wear and cracking problems of the stainless steels leading to the present abandonment of both classes of stainless steel are described. In particular the dependence of the toughness of type 410 stainless steel on its tempering temperature and the susceptibility of that steel to quench cracking are highlighted because problems have been caused by both of these metallurgical factors.IntroductionAs part of a desire to improve the efficiency of a fifty-year old hydro-electric generating station on the Saint John River, the decision was made to change the journal and bearing material for the shaft bearings, which are stave-type bearings. For the initial fifty years of operation the bearings had been wooden (lignum vitae) and had run on the carbon steel shaft directly. For one of the four unit s at this station the performance of this combination has been truly excellent, and the remaining three sets of bearings had performed well. However there had been shaft wear on the units and the wear had made the shafts somewhat elliptical when a decision was made to install some sort of new journal on to three of the old shafts. [In addition to the wear on the carbon steel journals it was found that one shaft was significantly softer in the bearing area than it was immediately above the bearings (180 Vickers in comparison with 230 to 250 Vickers)] ."

Jan 1, 1985