Search Documents

By W. Kempson

"As has been noted on numerous occasions, the vertical shafts being sunk around the world are all tending to get deeper as we seek to take advantage of higher grades of minerals which can sometimes be found at greater depths. One of the challenges with these deeper shafts is the requirement to supply services to the mine’s operations at depth as well as the requirement to dewater the mine. Both the supply of water and the dewatering of mines is generally done using piping. With the greater shaft depths, this piping is now required to contain higher pressures as well as to accommodate changes in temperature resulting from normal mine operations. This paper will discuss the requirements for the design of high pressure piping in deep vertical shafts. The discussion will start with the general definition of the systems and the detailed design requirement. Once this is clearly outlined, we will discuss the options available for fulfilling these requirement as well as the advantages and disadvantages of each of the systems. We will finish with the installation recommendations and provide a basis for the maintenance of these systems. INTRODUCTION Piping in vertical shafts is used to provide a number of services in underground workings. These services vary depending on geographical location and the type of the ore body which is being mined. For example, in the Zambian Copper mines, one of the largest requirements for in shaft piping is for dewatering. Similarly in the Gold deposits in the West Wits basin as well as the deep level Copper deposits in Arizona, one of the largest uses for the piping is the supply of a cooling medium to underground workings to create a safe working environment (this can in the form of water or of glycol depending on the application). In South Africa, systems were installed which used the hydrostatic head which is generated from supplying chilled water to mines whose depths exceeded 2,000 m below surface. This chilled water was supplied as a closed system, allowing for high pressures to be generated which was then used to supply useful work (for example, Rock Drills, Face Cleaning and other ancillary services) whose power was traditionally supplied by compressed air or electricity. This system was initially researched by Chamber of Mine in South Africa. The design pressure range of these systems is 14 MPa to 18 MPa."

Jan 1, 2019

By P. C. Garg

"IntroductionThe Central Mine Planning and Design Institute (CMPDI) of India, started planning the extraction of thick seams highly susceptible to heating in 1977by the French method of sub-level caving and/or multi-slicing. Nitrogen flushing was proposed for inhibition of heating by the author in one such project - the Kotadih colliery.Inhibition of heating was unheard of in the Indian coal industry before 1977-78. The usual practice was to seal off a district or a part of the mine or the entire mine when spontaneous heating occurred. With very little equipment in a normal bord and pillar district and a low production rate, the financial loss in capital assets and in production did not warrant any serious thought for inhibition of spontaneous combustion. With the planned advent of longwall mining, particularly sub-level caving, with heavy capital investment as well as high production potential, the sealing of a longwall face due to spontaneous heating could not be considered an appropriate solution.Principle of Inhibition of SpontaneousCombustionFrench engineers have established that a fire will not break out when oxygen is 15% or lower in the general body of the air. However, once a fire starts, the percentage of oxygen has to be reduced to 2% - 4% to extinguish it. It is this principle which has been used at Blanzy Coalfield in France to inhibit heating and it is claimed that this has retrieved the integral sub level method of mining. Nitrogen infusion has been used in Frence since 1978 to keep the oxygen content below 14% in the goaf."

Jan 1, 1987

By John H. Low

Introduction Despite the fact that the .association of magnetite with chrysotile asbestos in the parent producing area of the world, the Thetford Mines - Black Lake area, has been recognized since the ores of that region were first known, magnetic methods were not extensively employed in exploration for asbestos until about the beginning of 1949. Since then, large areas of Ontario, Quebec, and the eastern United States have been prospected both by aeromagnetic and conventional ground magnetic methods. Prior to 1949, a limited amount of magnetic work had been done, notably that of A.H. Miller (1, pp. 184-186), which was carried out in conjunction with the geological survey of the Thetford area by H. C. Cooke (2) in the years of 1930 to 1932. At that time, Miller pointed out that the occurrence of asbestos is associated with very large magnetic 'anomalies' and that, within the Pennington dyke, an area of asbestos- bearing peridotite could be distinguished, by the anomalies, from adjacent areas of non-asbestos ?-bearing peridotite. Since he .also observed large anomalies in what were believed to be ?barren areas, Miller concluded, however, that the magnetometer could hardly be of much or any value in the direct location of asbestos War .and post-war demands on known reserves of asbestos ore, however, stimulated the search for new deposits, and an economical and rapid method of directing speculative drilling was most desirable.

Jan 1, 1951

By Liguang Wang

The froth phase in flotation has received much less attention than the pulp phase despite the fact that froth stability plays an important role in determining flotation performance. Froth stability is largely determined by the stability of thin foam films, which in turn has a strong correlation with the critical rupture thickness (Hcr) of the films. In the present work, a new approach to predicting the Hcr values of thin foam films in flotation froth phase was proposed and examined. The Hcr values were calculated using an advanced capillary wave model with input parameters being surface tension, film radius, capillary suction pressure, and intersurface force. The intersurface force was estimated by using the Stefan-Reynolds lubrication approximation to fit the measured thinning rates of single foam films formed in a Scheludko ring cell, where the film radii were less than 50 microns and were kept constant during the film-thinning process. A comparison between the predicted and experimental Hcr values was made for the films with the use of sodium chloride as background electrolyte and in the presence of various frothing reagents such as methyl isobutyl carbinol (MIBC), polypropylene glycol with an average molecular weight of 400 (PPG400), and sodium dodecyl sulphate (SDS), at different concentrations and film radii. It was found that the model correctly predicted the trends of Hcr-versus-concentration and Hcr-versus-film radius curves. Moreover, the predicted Hcr values matched well with the experimental ones of the foam films containing either SDS or PPG400. For the foam films containing MIBC, however, the model overpredicted the Hcr values. The reason for this discrepancy was discussed.

Jan 1, 2016

By Mariam Melashvili, Chris Fleming, Rene Jackman

"A study was undertaken to develop a flowsheet for treating a high grade silver/gold ore body by cyanidation, CCD and Merrill Crowe precipitation, with tailings detoxification to meet stringent limits for cyanide and thiocyanate concentrations in the final discharge. In one of the flowsheets examined, free cyanide in the final leach liquor was recycled to the mill where it was hoped that it might react beneficially with fresh ore to reduce the cyanide makeup by an equivalent amount. However, laboratory results suggested that most of the cyanide recycled to the mill reacted with iron forming a soluble ferrocyanide complex. This would have had a negative impact on cost, not only because the cyanide recycled to the mill could not be claimed as a credit, but also because the presence of ferrocyanide in the final tailings meant copper sulphate had to be added to the SO2/air cyanide detoxification process to precipitate the iron cyanide. In an alternative flowsheet that was examined, recycling of cyanide to the mill was abandoned, and this allowed the milled slurry to be pre-aerated in a single mixing tank before cyanidation. During alkaline pre-aeration, any ferrous ions that are generated in the mill are oxidized to ferric ions, which, unlike ferrous ions, are inert in cyanide solution. This significantly reduced cyanide consumption and lowered costs in the detoxification of the tailings. In this paper, the cost implication of these two circuits is compared.INTRODUCTIONMost of the gold that is produced by hydrometallurgical processes is recovered by cyanide leaching. The reason for that lies in the superior thermodynamic stability of the gold cyanide complex and the favorable economics this confers on the process (Fleming, 2014). However, the gold in most of the gold-bearing ores processed is a very minor component, and therefore, the leaching response is often dominated by that of the host minerals.Many gold ores treated by the cyanidation process contain iron minerals. Cyanide reacts readily with some iron minerals forming ferrocyanide as one of the compounds. Ferrocyanide is stable when solutions are exposed to air and does not retard the dissolution of gold. In fact, it has been claimed that potassium ferrocyanide in the presence of oxygen is a weak solvent for gold (Hedley & Tabachnick, 1958). The main problem with the formation of this compound is the consumption of cyanide. Ferrocyanide contains six molecules of cyanide for each atom of iron {Fe(CN)64-} so the wasteful consumption of cyanide is greatly increased by its presence. Thiocyanate is also often produced during the reaction of certain iron sulphide minerals with cyanide, and contributes to the wasteful consumption of cyanide. In addition, environmental regulations in certain countries demand that thiocyanate be removed from the tailings, and this adds significantly to the cost of tailings treatment."

Jan 1, 2016

By A. Atrafi, L. Barroilhet

The top size of particles in the flotation of potash ores, which can be as large as 4 mm, exceeds by far the top size in other flotation plants. It is then understandable that while long chain amines are used in the flotation of fine fractions (below 0.8 mm) of potash ores the coarse particle flotation also requires an extender oil. While new and very promising fluidized-bed flotation machines (e.g. HydroFloat) constitute a significant development in the flotation of coarse particles, in the area of extender oils, as reviewed in 2007 by Strathdee, Gotts and McEachern, there have been no new developments to replace the industry standard asphaltene-based carcinogenic extenders. This situation first of all results from the experimental problems that arise when water-soluble minerals like sylvite are to be tested in saturated brine. Both oils and longchain amines are water/brine insoluble. The oil with the amine dissolved in it can however be emulsified and then used as an extender oil. Such oil droplets must wet KCl particles and the emulsion must be stable to avoid handling problems. In this paper we test the use of the phase inversion technique as a method of studying wettability of KCl particles by the oil in saturated brine, and the effect of amine dissolved in this oil on the wettability. The results show that this relatively simple technique can be used to characterize the wettability of fine KCl particles by the tested oil and to determine the effect of added amine on it, and so it can be useful in selecting proper extender oils.

Jan 1, 2016

"Line Creek Resources Ltd. produces three million clean tonnes per year of metallurgical and thermal coals for the international market. The mining operation, which is located in the mountains of southeastern British Columbia, produces coal from four pits by conventional truck and shovel methods.The South Pit, which has been in operation since J982, has a benched highwall 490 m in height. Shallow dipping coal seams at the base of the syncline formation will be exposed in the highwall over the next four years of pit life. The first of these seams, which will measure 500 m in final highwall length, was exposed in J994. An auger, powered by a 1250 hp engine capable of cutting 2.2 m diameter holes, was brought on site in J994 and has proven to be a successful means of recovering coal from the J3 m thick seam.This paper covers the background to the selection of an auger mining method to recover highwall reserves together with the geotechnical and methane considerations for this approach.IntroductionLine Creek Resources Ltd., a wholly owned subsidiary of Manalta Coal Ltd., owns and operates the Line Creek mine. The operation which consists of four active pits, a processing plant, and rail loadout is located in the southeastern coal fields of British Columbia. Figure 1 shows the general area.The coal bearing sequence at the mine is preserved on the east and west limbs of a major syncline. Up to twelve mineable coal seams, ranging in thickness from 2 m to 15 m are contained in the formation. Within the pits the seams are stratigraphically consistent and structurally undisturbed, except for small-scale thrust faults that create multiple repeats of the seams."

Jan 1, 1995

By N. Katsikaros, R. Agius, B. Adaszynski

"With stricter limits globally being imposed on cyanide discharge levels in plant tailings, having a reliable and well designed cyanide detoxification circuit is critical for any operation. The INCO SO2/Air method is most commonly used for cyanide detoxification where sulfur dioxide and oxygen combine to oxidize cyanide to the much less toxic cyanate. This paper discusses the steps involved with the development, from laboratory through to design, of a robust cyanide detoxification circuit. The goal is to produce a cyanide detox circuit that reliably meets discharge target with the lowest operating and capital cost.Design begins in the laboratory where continuous tests simulate full scale operation of a detoxification circuit. Detailed design relies on several design parameters, based on theory and experience, to ensure the reactor can satisfy requirements of the cyanide destruction reaction. Selection of the correct reagents and their supply to the reactor is important to an operable process with minimal operator workload. The operability of the system relies on correct process control strategies to maintain optimal reagent addition and chemical conditions in the reactor. These design factors are critical to providing a robust plant that will consistently meet cyanide discharge levels, ensuring uninterrupted production and plant profitability."

Jan 1, 2014

By S. Razavialavi

In the planning phase of every construction project, layout of temporary facilities is a crucial task; site layout can affect safety, travel cost and time, construction productivity, and space utilization. However, site layout planning can be a complicated problem, due to the interdependency of influencing factors. Although interaction among activities is one of the major drivers of site layout planning, it has not been properly addressed in past research. In this study, simulation is presented as a promising tool to address this gap. The capability of simulation technology to model complex processes in construction projects makes use of simulation tools in site layout optimization problems effective, while existing methods are unable to perfectly model these problems, in some cases. Additionally, the advantages and challenges of implementing simulation are assessed and a generic framework for simulation application in site layout planning is proposed.

Aug 1, 2013

By C. Gu

Flow field design is critical for PEM fuel cells. The flow field design can affect reactant distribution to the catalyst surface, water management, thermal management and current collection. Therefore, it has tremendous impacts on the fuel cell performance and durability as well as reliability and operational flexibility. In this paper, an optical method is used to study the reactant distribution in the flow field channels of two commonly used flow field designs, straight channel design and serpentine channel design. Images of the flow patterns are shown followed by discussions of the flow patterns.

Jan 1, 2005

By G. T. Lapidus, O. J. Solis-Marcial

Currently, ores with high-grades of copper oxides and secondary sulfides have become increasingly scarce, which has encouraged industry to look for alternative raw materials to obtain copper. The problem is that primary sulfides are difficult to dissolve at near ambient conditions. Proposed hydrometallurgical processes have not been implemented beyond a pilot or demonstration scale. One of the principal disadvantages is that the majority of these processes are not viable with ores that contain less than 4% copper. One of the more recently proposed techniques involves the use of organic solvents in the dissolution of copper concentrates with a chalcopyrite content of between 20 and 30%, which has shown high efficiency. The present research explores the ability of this process to leach copper from low grade chalcopyritic ores (<4% Cu) at different temperatures ranging from 20 to 50°C. It was found that depending on the temperature, high percentages of copper were extracted in 40 to 100 minutes, using different oxidants. Additionally, distinct leaching behavior was observed with each oxidizing agent. In some cases, the extraction kinetics adjusted to the diffusion controlled shrinking core model.

Jan 1, 2014

By Ken Woloschuk

??Owners?Perspective ??Owners?Challenges ??EcoNomics?Delivery Model ??Projects ??Project Outcomes ??Questions ??Balancing the triple bottom line initiative: ?shareholders expectations of economic costs and benefit; ?stakeholders expectations of social and environmental costs and benefits; ?deciding what is sustainable and which design alternatives are the most sustainable. ?? Delivering required project outcomes

May 1, 2008

By E. G. Joe

"Recent trends in Canadian mineral processing were reported in seven areas of interest covered by seventeen technical papers at the 1976 Annual Meeting of the Canadian Mineral Processors, held at Energy, Mines and Resources' Camsell Hall, Ottawa. New milling equipment included the Enviro-Clear thickener, large-volume Outokumpu flotation machines and abrasion-resistant polyurethane screens. Grinding experiences from a variety of milling operations were reported. Opportunities for increased sizing and grinding efficiency were presented. Flotation control by digital computer and by chemical additions were described in two mill operations. Slurry pumping and sampling techniques were described for various operations. Environmental control in milling was reported concerning dust suppression, arsenic removal and tailings disposal. Several aspects of gold milling were described by the most recently commissioned gold mine and by CANMET. Potash operations were reported showing the similarity of processing and process control to that of metallic minerals."

Jan 1, 1976

By R. Esteban, D. Runnels, S. Girgin, J. Torrealba-Vargas

"Each mineral processing project requires early testwork to evaluate the economic potential of a deposit. The testwork needs to be efficient and it should provide enough information to obtain key parameters, first for a high level flowsheet selection at the conceptual and PEA stages and then, for later stages, to confirm the flowsheet selection and optimize the metallurgical efficiency of the plant. The testwork should consider all rock types or lithologies present, and carry out testwork for the purpose of sizing the major processing equipment.A successful project requires that the project stakeholders develop an efficient sample collection program to produce enough material for a scoping and pre-feasibility level program. This involves the participation of a team of geologists, mining and metallurgical engineers in the project, as early as possible, to define the deposit characteristics that need to be validated.The project schedule requires a close control of the testwork scope, procedures, and timing, but also the efficient analysis of results to provide indications of red flags that could impact circuit design as early as possible.In some cases, projects are put on hold due to fluctuations of the world economy until the return of more favorable conditions. In that scenario, prior data analysis of former testwork results could reduce significantly the amount of testwork required to restart a project. The paper will also present examples where the analysis of former testwork data was used to reduce the amount of new testwork in addition to presenting examples of latest projects where the above-mentioned test program approach was followed."

Jan 1, 2016

By Andrea Lisjak

The mechanical behaviour of Opalinus Clay, an indurated over-consolidated argillaceous rock, is heavily influenced by the presence of preferably oriented bedding planes. The objective of this study is to illustrate a new modeling approach aimed at capturing the bedding-induced anisotropy of Opalinus Clay as observed in the laboratory and in situ. The combined finite-discrete element method (FEM/DEM) is employed as the main simulation tool. FEM/DEM is a numerical method that models material damage processes by explicitly considering fracture nucleation and propagation. A transversely isotropic elastic constitutive law is used to account for different elastic property values in the direction parallel and perpendicular to the layering, while strength anisotropy is captured using a directional cohesive fracture model. Quantitative calibration and validation of the model is based on laboratory results of indirect tensile tests and uniaxial compression tests. Emergent strength and deformation properties, together with the simulated damage mechanisms, are shown to be in good agreement with experimental observations. Preliminary results relative to the analysis of a circular tunnel show that the approach is able to reproduce the main Excavation Damaged Zone (EDZ) formation mechanisms as observed in the field.

Jun 1, 2012

By A. M. Bell

"Hallnor mine is in the township of Whitney, Porcupine district. To date, its production of gold has been second largest in the east Porcupine field. Ore was discovered in the property in 1936 by diamond drilling in overburdened country. This drilling was undertaken by Noranda Mines following the discovery of ore in conglomerate at Pamour 1 mile to the east.Milling commenced at the Hallnor in June 1938, and to the end of 1945 432,000 oz. gold had been produced from 889,000 tons of ore, giving an average recovery of 0.49 oz. a ton.The West mine of Pamour, the Broulan orebody, and the veins on the Hallnor and Bonetal are all parts of a mile long vein system that has been separated into three sections by cross faulting. In consequence, they could well have been described in one paper. In treating them individually the viewpoint obtained from each may lead to conflicting opinions, and any conclusions advanced in this paper on the general structure should be modified by the conclusions advanced in papers on the neighbouring properties.GENERAL GEOLOGYRock FormationsThe Hallnor orebodies occur within 400 feet of the contact between lavas and sediments, and may lie in either lavas or sediments. The lavas near the ore consist of flows of pillowed andesite and one flow of more acid and less sheared and chloritized lava locally named trachyte. These flows strike east-west and dip steeply. At the surface on the east side of the property the volcanics have been intensely altered to a massive carbonate rock having a north-south thickness in excess of 1,000 feet . This carbonate body extends west across the property with a plunge of 45° (Fig. 1)."

Jan 1, 1954

By Maureen A. McGuinness

Kidd Mine, an Xstrata Copper operation in Timmins, Ontario, operates a 400 t/h pastefill plant that provides paste backfill to stopes at the depth of 9000 ft. This paper will cover the operating practices of the pastefill plant both on surface and underground, highlighting tailings excavation, paste mix design and the pipe maintenance program. Kidd Mine, une opération d&apos;Xstrata Copper à Timmins, Ontario, opère une usine de remblai d&apos;une capacité de 400 t/h. Le réseau de distribution permet d&apos;acheminer le remblai en pâte juste qu&apos;à une profondeur de 9000 pi. Cet article couvrira le mode opératoire de l&apos;usine de remblai tant à la surface que sous-terre en mettant l&apos;emphase sur l&apos;extraction des rejets miniers, la recette du remblai en pâte ainsi que le programme d&apos;entretient du réseau de distribution.

Feb 1, 2008

By W. R. Tyson

Imperfections such as lack-of-fusion and undercut are inevitable in field welding of pipelines. Above a certain size, such defects must be removed or repaired. In the present state of the art, determination of allowable defect size is done by Engineering Critical Assessment (ECA). This requires measurement of toughness, and comparison of toughness with crack driving force. ECA methods used in current international pipeline standards will be reviewed and compared.

Jan 1, 2010

By Lawrence Devon Smith

"The Management and Economics Society has undertaken a survey of industry practice in the evaluation of mineral projects. The survey addresses a number of issues relating to evaluation techniques, discounted cash flow methodology, and risk. Completed during the spring and summer of2005, the results provide a record of opinion at an active and vital time in our industry.The 2005 survey questionnaire was distributed by e-mail to groups and organizations around the world. There were 22 respondents out of several hundred questionnaires distributed (we gather this small proportion of respondents is typical for such surveys). The responses, although a small number, show a consistency that suggests that the survey has captured the views of the industry. The results of the survey are summarized below in series of tables and graphs.The reader is cautioned that the results are a snapshot of industry practice at a point in time as represented by a small sampling of the industry's practitioners. These results should be viewed as indicative values."

Jan 1, 2003

By J. H. Archibald

"This paper describes the use of vector analysis for determining the intersection of mineral deposit veins. The mathematical evolution of the analysis is outlined.IntroductionMany mineral deposits can be characterized by sets of intersecting veins. Often a vein will have a steep dip and may intersect with another similar vein. Finding the intersections of these veins is usually done by graphical means. Structural geologists, by the methods of descriptive geometry, can usual ly predict where intersections of veins will occur. This method normally requires accurate drafting and layout of the problem and does not always lend itself to solution in the field.Another method for solving this problem involves the use of vector analysis, which is easily adapted to hand-held programmable calculators. It is assumed at the outset that the reader is familiar with the dot and cross products used in vector analysis. Two excellent references are cited at the end of this note for convenience.A plane, in general, is defined by three points. The points of interest here are the points where three vertical drillholes penetrate the vein, or plane, in question. The elevations of these three points are best referred to sea level. This requires knowing the elevation of the collar of the drillhole above sea level and the drillhole depth from the collar to the vein. The elevation of the intersection point is then found by subtracting the hole depth from the collar elevation. These three points now define the plane of the vein. A similar set of three points will define a second vein, and it is our object to show analytically their intersection if it exists."

Jan 1, 1983