Search Documents

By Huilan Yang, Feng He

This paper intends to introduce the development of copper smelting and converting technologies in China in recent years, with a particular emphasis on the introduction of various continuous converting technologies, and moreover, it analyzes the advantages and disadvantages of those technologies, including their impact on the downstream anode refining from different points of view. INTRODUCTION At present, many converting technologies are used in copper pyro-metallurgical plants in China, including Peirce-Smith (PS) converter, flash converting furnace, multi-lance based top blowing, bottom blowing and so on. These technologies have spanned a wide range of time. PS converter technology has been applied in copper smelters for many years and most of the blister copper have been produced by this technology; flash converting technology has been developed since 1990s and been maturely applied in several plants up until now; top blowing and bottom blowing technologies have been revived in China in the past decade and boast good environmental protection performance, energy efficiency, throughput capacity and short process flow. All of the said technologies have reference operations in treating high-grade matte. As more and more attention is paid to environmental protection globally and copper smelters continuously seek for cost reduction, it is necessary to share those converting technologies, especially those new converting technologies derived in China, with copper smelting practitioners in the world. This paper aims to analyze the advantages and disadvantages of various technologies from a macroscopic view and discuss their actual application effects, current developments and future improvements. BRIEF INTRODUCTION OF VARIOUS CONVERTING TECHNOLOGIES IN CHINA China has seen a rapid development in copper smelting industry in the past 30 years and has become the largest gathering place of copper smelters in the world, most of which are operating with PS converting furnace technology, however, with the increasingly strict environmental requirements of the Chinese government in recent years, the low-level pollution issue and the disadvantage of large gas exhaust amount per unit of copper of converting furnaces are particularly prominent.

Jan 1, 2019

By J. B. Brodie, C. Pelletier

"The vulnerability of Canadian and U.S. companies, their directors, officers and employees to onerous penalties associated with violations of environmental statutes and common law actions has provided the impetus for the increasing use of environmental audits. This trend is developing in direct proponion to the cost and difficulty of obtaining liability insurance. Companies operating in British Columbia should be cognizant of developing legislative and enforcement trends and their implications for individual and corporate responsibility. Canadian mining companies doing business in the U.S. should be particularly aware of the environmental exposure which may be assumed with property acquisition or by operations which produce or use any of an ever-increasing list of regulated substances.The environmental audit is now a key component of prudent business planning which will identify noncompliances and environmental liabilities, outline defensive strategies, and assist in a legal defence should charges be laid. This paper will discuss the purpose and mechanics of an environmental audit with emphasis on those features which will maximize protection against statutory and common law actions.IntroductionThe environmental audit is but one weapon in a comprehensive defensive strategy for corporate and individual survival in an increasingly litigious world. The principles of the environmental audit have been formulated as a logical response by management to an ever-growing list of environmental vulnerabilities, which often have the potential to result in plant shutdowns, prosecutions or fmancial liability of major proportions. Accordingly, the audit may play a critical role in maintaining profitability as well as assisting in the defence of a company and its employees against actions taken by regulatory agencies and citi7.cns under statute and common law. Should convictions result from these actions, the penalties are likely to be ameliorated by the demonstration of due diligence through management policy supporting the audit procedure.An awareness of environmental sensitivities, strict adherence to licensing requirements, and planning for environmental emergencies are now generally considered to be as important to profitable performance as operating costs, metal prices, and labour peace. Why is this so? The increased priority given to environmental matters is partly a result of changing attitudes amongst the mining profession, but perhaps more importantly, it is also a direct consequence of the proliferation of ever more stringent environmental legislation, the targeting of management for responsibility and the draconian penalties imposed for violations of such legislation. Contributing to this trend are recent court decisions involving disputes of an environmental nature in which the standard of care required for a successful defence now requires almost super-human diligence in environmental management. The principle of ""strict liability"" (in which negligence or permit violation does not have to be shown) is also being increasingly applied in the resolution of civil actions."

Jan 1, 1988

By T. R. Raponi

"The Williams Mine, Canada's largest gold mine, processes over 6,000 t/d of ore utilizing SAG/ball milling, leaching and CIP, carbon stripping, electrowinning and refining to produce gold dare bullion.Grinding accounts for over 50% of milling costs with grinding media, power and mill liners making up over 75% of grinding costs. Since 1991, several changes in these areas have been made which have significantly reduced costs, while fineness of grind and mill recovery have both been increased.This paper discusses the changes made in the grinding circuit over the past few years and assesses their impact on operating costs and mill operations.IntroductionThe Williams Mine is located in the Hemlo area of northwestern Ontario, about 40 km east of Marathon. It is operated by the Williams Operation Corporation, which is equally owned by Teck Corp. and Homestake Canada Inc. Canada's largest gold mine, the Williams Mine commenced operation in October 1985 at a rate of 3, 000 t/d. Mill throughputs have typically exceeded design, averaging 3, 397 t/d in 1986, and 3,380 t/d in 1987. In August 1988, production was increased to 6,000 t/d. Throughput averaged 4,212 t/d in 1988. Production increased over the next few years averaging 5,477 t/d in 1989, 6,248 t/d in 1990, 5,987 t/d in 1991, and 6,283 t/d in 1992. With a recovery of over 95.5%, production for the first three quarters in 1993 is averaging 6,408 t/d.GeologyThe main ore body is a steeply dipping conformable zone of microcline-quartz-muscovite rock. It occupies the contact zone between hanging wall metasedimentary rocks and foot wall felsic quartz feldspar porpyritic rocks of possible volcanic or subvolcanic intrusive origin. The ore body is enveloped by muscovite schists which are thickest on the footwall side. The schist is enriched with tourmaline, pyrite, and green mica containing vanadium and barium. The ore body contains pyrite and barite which occurs mostly in laminae and bands to veinlets and breccia fillings. The gold occurs as free (native) grains, 20 to 30 µm in size at grain junctions of the microcline and quartz. Visible gold is rare in the main zone. There are commonly two or more discernable layers of economic value which are separated by weakly gold mineralized material which usually consists of muscovite schist, barite rich zones or sulphide poor-microcline-quartz rock and in the upper and western fringes by biotite rich schist with feldspathic fragmental characteristics. Molybdenite is a common constituent as very fine disseminated grains in the microcline-quartz rock and is most prominent with gold enrichment. Stibnite and realgar are two of the more common accessory sulphides."

Jan 1, 1994

By J. Ouellet

The design of hydrostatic liner for a deep potash mine shaft in Saskatchewan poses tremendous technological challenges. Technology has evolved to a point where one could consider a new innovative approach to hydrostatic liner design. But there is still a place for conventional technologies such as cast iron tubbings. As will be discussed in this paper, improvement to manufacturing process, installation procedures and even new materials can bring this technology to an excellent level of performance. With the spur of new projects in the potash industry of Saskatchewan, the authors worked in various shaft liner designs from the conceptual stage through to the construction phase. They were either directly leading the design work on some of these projects or acting as an external reviewer on others. Most of these shaft liner designs involved cast iron tubbing technology and ground freezing. The major challenge in sinking potash shafts in Saskatchewan is to go through a water-bearing ground formation under high pressure, known as the Blairmore or Manville fm. The only proven stabilizing technology for these formations is ground freezing. For a potash shaft, dry shaft conditions are highly desired, so a fully waterproof hydrostatic liner is required. All the existing potash mine shafts in Saskatchewan, except for two with composite steelconcrete lining, used the cast iron tubbing technology. Two new shaft tubbing liners have been constructed recently, one in the Athabasca Basin and one for a potash mine in Saskatchewan. When the authors began working on these new projects, what became quickly evident is that the technological knowhow for designing and constructing tubbing liners was no longer available within Canada and that the past construction methods used to sink tubbing lined shafts was obsolete. The tubbing liner for the shafts sunk in the sixties were designed either by German or British companies. In both of these countries only few tubbing lined shafts were sunk in last 40 years and the technology used in the sixties was not improved. There are only few countries where tubbing is routinely produced and installed: China, Russia, Ukraine and Poland. Out of these countries Poland is the one where this technology is the most advanced. The authors, working in close collaboration with engineers from Poland, attempted to rebuild this knowledge for the mining industry in Canada. This process involved thorough analysis of old technical reports, literature review and study of current polish design and construction practices as well as site visits of existing shafts. Through actual construction experience, some lessons were learned as well as ideas for improvements. In this paper, the authors will present a succinct review of design and procurement process. But, the practical aspects of the construction and installation methodology will be treated with more emphasis, more specifically the practice leading to good liner performance. Some of the poorly understood technical aspects of tubbing installation will be discussed more thoroughly and some currently accepted myths dispelled.

Aug 1, 2013

By B. Y. Park

This paper develops a series of three-dimensional simulations for the Bayou Choctaw Strategic Petroleum Reserve. The U.S. Department of Energy plans to leach two new caverns and convert of one of the existing caverns within the Bayou Choctaw salt dome to expand its petroleum reserve storage capacity. An existing finite element mesh from previous analyses is modified by adding two caverns and increasing the size of existing Cavern 102. The structural integrity of the three expansion caverns and the interaction between all the caverns in the dome are investigated. The impacts of the expansion on underground creep closure, surface subsidence, infrastructure stability, and well integrity are quantified. The results show that from a structural viewpoint, the locations of the two newly proposed expansion caverns are acceptable, and all three expansion caverns can be safely constructed and operated.

May 1, 2009

By Richard Klimpel

"Over the last 15 years, there has been a number of plant scale sulfide mineral flotation tests organized by this author specifically aimed at understanding how flotation rate varies with reagent type and dosage. With regard to the Interaction of collector dosage, particle size, and frother type, the eight specific trends listed in the paper (Illustrated with data from two specific case studies) are qualitatively the same for almost all plants studied in some depth. The Interaction of flotation rate K and equilibrium (Infinite time) recovery R in the plant has been denoted as the R/K trade-off. The effect of collector dosage on the rate of flotation of specific particle size intervals is particularly interesting and once understood, is quite useful In understanding how industrial flotation plants respond to changing reagent type and dosage. The location and magnitude of the R/K trade-off can be different for various ores and various plant configurations, but the RIK trade-off is almost always present. The purpose of this paper is to clearly describe and illustrate the nature of this very Important flotation system Interaction so that operating engineers have a starting reference point for beginning successful plant Improvement studiesIntroductionIt is well recognized by industrial froth flotation plant operators that improving existing sulfide circuit performance is often difficult due to the self-compensating systems nature of the froth flotation system, e.g. Klimpel (1988, 1989, 1995). Extensive plant testing with existing and new reagents by this author throughout the world has clearly shown that one of the more important self-compensating mechanisms is the Interaction between collector dosage, frother type, and particle size. The term self-compensation in flotation simply means that as the plant operator consistently changes one parameter in the same direction, the nature of the froth flotation system Is such that the circuit will eventually begin to resist this controlled parameter change by automatic (uncontrolled) changes In other parameters and the overall circuit performance will go through a maximum or minimum (hence causing the operator to stop the parameter change)."

Jan 1, 1997

By E. A. Brown

"IntroductionBACK IN THE nineteen-thirties, when Eldorado was a private company and was preparing to become Canada's first radium producer, the Mines Branch in Ottawa did much work on the development of chemical processes for the Port Hope refinery (1).In 1945, after the Canadian Government had taken over Eldorado for •atomic energy reasons, the Mines Branch was called upon again, this time to help out by looking into ways and means of improving ore treatment methods for the mine at Great Bear Lake. A group of technical men was assembled to devote full attention to this work, which was known as the Eldorado Project.Three years later, in 1948, the Government decided to reopen the development and operation of uranium properties to private enterprise.Since it is a function of the Mines Branch to assisit private development of Canadian mineral resources, this new uranium policy made it important for the Branch to be in a position where it could provide up-to-date services, technical assistance, and information relating to treatment of radioactive ores, mineralogy of radioactive ores, and assay methods for radioactive ores.At the same time, .because of the demand for increased uranium production, lower grade ores had definitely come into the picture, ores that might be of decidedly lower grade than, say, Eldorado pitchblende, and of entirely different nature."

Jan 1, 1953

By A. Sheikh, S. Hardcastle

"Various methods of leaching are being used by Denison Mines Ltd. Uranium Operations. This study was designed to investigate the flood leaching operation of two parallel inter-connected stopes contained by pressure bulkheads. The teaching muck piles, created from large scale uppers production blasts, are aerated by compressed air lines laid beneath the pile prior to blasting.A SFr, tracer gas, injection technique has been employed to determine the post-blast integrity of the single-ended air distribution system. SF6 was injected into the compressed air line feed to the stopes and collected at borehole exhausts from the stopes in grab-sampling bags. Analyses of the air samples were performed with a gas chromatograph.The system was designed to give a sufficiency of oxygen to sustain bacterial activities used to enhance the leaching recovery in the muck piles. The results obtained indicated that there is a minor anomaly in the distribution system that may not be critical to the operation. Compared to an idealized case, the over-all efficiency of aeration throughout the muck is estimated at over 85%."

Jan 1, 1988

By J. A. Finch, J. Vergouw

"Flotation selectivity becomes progressively more difficult to achieve with decreasing particle size. One of the possible problems is agglomeration, i.e. particles clustering together. One mechanism derives from the surface charge all particles develop in water. Agglomeration driven by surface charge is known as coagulation. One form is coagulation between particles of two different minerals of opposite charge. Another is coagulation between particles of the same mineral when conditions are such that the charge approaches zero.The paper describes the method of measuring charge and a new automated settling technique for measuring agglomeration. The phenomena are illustrated with galena and pyrite. Methods of assessing the importance of agglomeration in the plant environment are still to be developed.IntroductionFine particles can agglomerate (i.e. adhere to each other) under certain conditions. This is counter-productive for any physical separation process, including flotation. One cause of agglomeration derives from the surface charge that all particles develop in water. Agglomeration due to surface charge effects is referred to as coagulation. There are two forms of coagulation. If the surface charge is brought to near zero then the force of repulsion is lost and particles coagulate. This usually applies to particles of one mineral type and the technical tenn is homocoagulation. On the other hand, if two particles have opposite charge there is an attractive force. Since the particles in this case are usually different minerals this is known as heterocoagulation.Both types of coagulation can cause minerals to be misplaced. In the case of heterocoagulation this is fairly obvious. One example that may be familiar is slime coating (fines of one mineral coating larger particles of another) But even homocoagulation can be a problem an agglomerate of the same mineral particles can entrap particles of another mineral."

Jan 1, 1997

By Patrik Ericsson

During the 90?s Atlas Copco and LKAB developed a pioneering fully automatic long hole production drilling system based on the Atlas Copco Simba W469 drill rigs. These drill rigs have since then drilled about 8.000.000 drill meters at the LKAB Kiruna and Malmberget mines. In 2005 LKAB ordered three new Atlas Copco Simba W6 C, to complement Simba W469s still in operation. These new Simbas are based on the latest generation computerized drilling technology have proven to meet the expectations of LKAB and now form a base for future automation in Kiruna and Malmberget mines. This paper will present experiences from the introduction of Simba W6 C in LKAB Kiruna and Malmberget mines. The paper will also elaborate on the latest developments in remote access and remote control technology making it a common automation option available for all computerized Atlas Copco drill rigs.

May 1, 2007

We report the studies of Proton-Exchange Membrane Fuel Cells (PEM FC) and hydrogen storage materials at McMaster University for the last 14 years. From the initial investigation of ionic conduction mechanism to the revelation of the origin of non-Arrhenius temperature dependence, as well as the synthesis and characterization of high temperature polymer electrolytes, both experimental and theoretical works have been compiled for the fuel cell membranes. In addition to the discovery of suppressed ionic conduction in Electrode-Membrane Assembly (EMA) and novel hydrocarbon PEMs based on micro-emulsion, the first evidence of hydrogen adsorption saturation by carbon nano-tubes was also achieved, which has been the bottleneck for the application of PEM FC. Prior to our study, a number of controversial publications have claimed the hydrogen capacity of these materials to be between 0.1 to 10.0 wt.%, and none demonstrated a plateau of adsorption with pressure that is consistent with monolayer saturation. Others suggested that the tube bundle structure is opened under high pressure to enable higher adsorption on newly uncovered surfaces, but received no confirmation. Using our home made high-pressure instrument with in-situ electrical probes, we found that a plateau is nearly achieved at about 300 atm in the room temperature isotherm, and that nanotube bundles actually compress with pressure instead of splitting, using in-situ electrical measurements.

Jan 1, 2005

By S Grönstrand, C. Perez, A. B. Yañez, F. Coddou, P. Morales, H. Elgueta

"The TankCell® 300 forced air flotation cell designed and built by Outotec, with active volume of over 300 m3, was installed at Codelco’s Chuquicamata concentrator in September 2008. After that, a program was conducted, where the new cell was tested against the plant’s existing flotation cells of type TankCell® 160, with an active volume of over 160 cubic meters.Testing program was exhaustive and detailed. Grade-recovery curves for each setup were reported, along with recoveries by particle size. Secondly, operational characteristics like air feed and froth height setpoints, and power consumption are compared side-by-side. As the third topic, gas dispersion characterization included velocity mapping, holdup, bubble size and bubble surface area flux operating range. The fourth area of interest was the retention time distribution (RTD) of the 300 and 160 m3 cells in comparison. A detailed campaign using radioactive tracer tests was conducted to clarify this.All of the investigations mentioned above are reported in separate papers for more detail. The aim of this paper is to collect the key findings, and present them in real terms, always referring to operability and metallurgy of the cells. It is destined for people designing new plants and to those improving and expanding existing ones. The most frequently heard question is: will the new large cells operate at same efficiency as the smaller ones. In short, the answer is: NO. They operate at improved efficiency!INTRODUCTIONIn the last two decades of minerals processing, there have been three dominant trends of development in the flotation technology: equipment scale-up, cell characterization and circuit modeling. Equipment scale-up has been rapid in the past two decades. In the year 1990, the largest flotation cell in use was 50 cubic meters of size. This year, 300 cubic meters is the largest installed cell. Characterization of flotation equipment and circuits is a very popular subject nowadays and has helped many operations to improve their recoveries through better control strategies, for example by using optimized air feed and level control profiles (Gorain, 2005), (Doucet, Gomez, Finch, 2006), or through better maintenance (Coleman, Urtubia, Alexander, 2006). Characterization work is closely linked to circuit modeling. The aim is to produce sufficient amount of data to allow reliable model building. These models are then used to design new circuits and to improve existing ones. So in summary, these three lines of development have slightly different aims – from capital and operational cost to performance optimization. Ultimately, they converge in the same end result – maximizing the profitability of the operation. Following chapters will summarize the extensive test work and scientific studies at Codelco Chuquicamata. The aim was to compare a TankCell® 300 cell, with nominal volume of 300 m3, against two TankCell® 160 machines, with 160 m3 volume in each. The work should yield answers to questions: does the larger cell produce similar results – is the scale-up successful?"

Jan 1, 2010

By P. P. Sinha, D. N. Bhatia, B. R. Ghosh, R. K. Gupta

Medium carbon, low alloy, high-strength steels containing Ni, Cr, and Mo are used for the fabrication of various types of high-strength fasteners required for launch vehicle structures. Cold heading properties and response to hardening and tempering are the essential requirements of the material for fabrication and application, respectively. Combining these two requirements is essentially warranted in high-strength fastener-grade steels. Cold heading properties require ductility, which can be achieved through spheroidizing treatments. In the absence of a suitable spheroidizing cycle for medium carbon 3.8 Ni, 1.8 Cr, 0.3 Mo steel, experiments were carried out with a theoretical understanding of the alloy system. This paper presents the experiments and results obtained after a spheroidizing treatment, which was carried out to optimize the process. Hardness measurements were carried out and microstructural studies were conducted to assess the spheroidization process and to determine the optimal spheroidization parameters.

Jan 1, 2007

By Paul Semple

"In 2007, Noront Resources Inc. discovered the high grade nickel copper PGE deposit in northwestern Ontario in a region now known as the Ring of Fire. Since the initial discovery, Noront has advanced the Eagle¹s Nest Project and in September 2012 released a feasibility study for the development of the Eagle¹s Nest Project. This paper summarizes the results of this recent study and outlines additional work planned in the next stages of project development. INTRODUCTIONThe following paper summarizes the findings of the recently completed feasibility study on Noront Resources Ltd.’s Eagle’s Nest Project. The feasibility study was compiled into a NI 43-101 report by Micon International. This paper is intended to summarize the major technical findings and for complete information, interested parties can find the entire NI 43-101 report at www.norontresources.com or on SEDAR.LOCATIONThe McFaulds Lake project area, which includes the Eagle’s Nest deposit, is located at approximately UTM 5844000 N and 547000 E, and between approximately 52º42’ and 52º50’ N latitude and 86º06’ and 86º24’ W longitude, approximately 250 km west of the community of Attawapiskat on James Bay and 575 km northwest of Timmins. The closest all-season accessible community to the McFaulds Lake project area is Nakina, 300 km to the south, where there is a paved airstrip, in addition to all weather road and railroad access (see Figure 1).The First Nations communities of Webequie and Ogoki/Marten Falls are located 90 km west and 120 km south southeast of McFaulds Lake, respectively. Both communities are served by regularly scheduled air service, primarily from Thunder Bay; both Thunder Bay and Timmins serve as support centres for the James Bay communities and the exploration projects in the area."

Jan 1, 2013

By Les Johnston

_ BACKGROUND - About EPCOR - Genesee Generating Station - Phase 3 Expansion _ TECHNOLOGY SELECTION - Selection Criteria - Combustion Options - Flue Gas Emission Control Options _ STAKEHOLDER VIEWS _ PROJECT STATUS _ EPCOR is an integrated utility company for water, gas, electricity and technology services. _ EPCOR has about 1.6 million customers in Alberta, Ontario, Manitoba, BC, and the U.S. Pacific Northwest. _ EPCOR Generation Inc. operates three power stations in Alberta which were in operation before deregulation, including the coal-fired Genesee Generating Station. _ EPCOR Power Development Corporation owns generating stations in Alberta, BC and Washington State and will be building the Genesee Phase 3 expansion.

May 1, 2002

By P. W. Godbehere

"INTRODUCTIONMagnetic mill linings have been developed from an invention by Mr. Bertil Brandt, the originator of the Skega rubber lining. The OREBED magnetic mill lining is a concept in which rubber covered strontium ferrite permanent magnets are arranged on the inside wall of a mill shell so that they attract magnetically susceptible material be it ore, media or tramp, to form a protective layer over the magnets and to serve as an operating surface with indefinite life.Noranda Mines Ltd. through its associate Norcast Division of Noranda Metal Industries formed a joint venture with the inventors to market magnetic mill linings in North America. For the past twelve months trials have been undertaken in conjunction with Orebed Inc. to test and develop these linings for grinding mill applications at the Horne Concentrator. Two independent milling circuits are currently being operated, one treating a siliceous gold ore and the other a copper slag.This paper presents the results of the magnetic lining test programme to date."

Jan 1, 1983

By N. M. Soonawala

Detailed regional geophysical and geochemical surveys, ground surveys and drilling were undertaken to follow-up the federal-provincial Uranium Reconnaissance Program (URP) over the 27,OOO-km2 Kasmere-Munroe area in northwestern Manitoba. An analysis of the URP data showed a fair correlation between the regional airborne radiometric results and lake-bottom geochemical results, both of which also correlated with the regional geology. More detailed surveys defined anomalies with greater precision within the broad zones outlined by the URP. The ground follow-up indicated that URP anomalies can be caused by varying degrees of uranium concentration in the rocks. Mineralization of interest was found in leucogranites at several locations within the survey area. Anomalous uranium concentrations were also found in coarse pegmatites and Hudsonian granitic intrusions. It can be concluded that large-scale regional surveys can be followed up in relatively short periods of time to yield meaningful results if a properly planned exploration sequence is employed, each stage of which successively narrows the area of interest.

Jan 1, 1979

By M. Rebolledo, N. Mora, G. Zarate

For decades, the mining industry has been focussed to find an efficient and economically attractive process for the leaching of chalcopyrite. Jetti Resources has developed a novel hydrometallurgical alternative to extract metals of value from mineral ores that the mining industry has struggled to process. Jetti’s catalytic technology, whilst being especially advantaged for extracting copper from low-grade and highly refractory minerals, such as chalcopyrite, seamlessly integrates with existing heap leaching methods and downstream processing operations. The technology uses a catalyst which weakens the metal-sulfide bond in the crystalline structure of the chalcopyrite mineral and alters the structure of the passivation layer allowing the leaching process to continue. Metallurgical test work was conducted to examine the effect of ore variability, in terms of grade and copper deportment. The results presented in this study highlight the amenability of the technology and demonstrate that it is possible to enhance leaching performance of copper primary sulfides over a wide range of copper grades, from 0.1 to 2.2%. Further, it is concluded that despite the copper grade, the tests with increasing chalcopyrite content render copper recoveries up to 4 times higher compared to the tests under non-catalyzed conditions. Jetti’s catalytic technology is currently being evaluated at larger scales, namely a commercial dump leach operation and 50-tonne crib tests. The results obtained thus far are compared to the results from conventional sulfide heap leaching tests. INTRODUCTION For decades, the mining industry has been focussed to find an efficient and economically attractive process for the leaching of chalcopyrite. Chalcopyrite (CuFeS2) is the most abundant and recalcitrant of the copper sulfides (Singer, 2017). Owing to its abundance and economic importance, it is the most demandable natural source for copper worldwide. In fact, the projected demand for copper is further expected to rise much higher beyond the current demand by the year 2020 (Panda et al., 2015). Therefore, it becomes imperative to find low intensity hydrometallurgical technologies for the extraction of copper from chalcopyrite in ores of such low-grades that are un-economic to concentrate and to augment the supply by extracting copper from ores with complex mineralogy that cannot be concentrated (Watling, 2013).

Jan 1, 2019

By J. B. Boisvert, W. Board, C. R. Mooney

"Traditional geostatistical modelling methods are difficult to apply to heavy-tailed deposits because the extreme positive skew of the grade distribution leads to bias. The focus here is on an innovative method of modelling the high-grade population by conditionally simulating discrete volumes (nuggets) of gold with marked Poisson and Cox processes. Capping and other ad-hoc manipulation of the assay data is not required; however, an intensity map for the point processes is required. The method is demonstrated on a dataset from an epithermal deposit and demonstrates an improvement in reducing smearing and controlling the skew of the grade distribution.RÉSUMÉ Les méthodes traditionnelles de modélisation géostatistique sont difficiles à appliquer dans des gisements dont la distribution de la teneur est à queue lourde car l’extrême asymétrie positive de la distribution de la teneur génère des biais. Dans le présent article, l’accent est mis sur une méthode novatrice de modélisation de la population à haute teneur par la simulation conditionnelle des volumes discrets d’or (pépites) au moyen de procédés marqués de Poisson et de Cox. La limite d’utilisation et d’autres manipulations ad hoc des données ne sont pas requises; toutefois, il faut une carte des intensités pour le processus ponctuel. La méthode est démontrée sur un ensemble de données d’essais provenant d’un gisement épithermal et elle montre une amélioration dans le lissage du flou et dans le contrôle de l’asymétrie de la distribution de la teneur."

Jan 1, 2015

By Y. X. Zhao

This paper briefly describes the characteristics and induced factors of coal mining bumps based on the investigation of recent bumps accidents occurred in China. According to the theory of non-equilibrium thermodynamic and dissipate structure, the process of strain energy accumulation and dissipation in the ?Coal-Surrounding Rock? system (CSRS) is discussed during the preparation of coal bumps. In addition, a series of experiments are conducted to analyze the relationship between bump-prone property and micro-structural characteristics of coal. The process of coal bumps induced by propagation of fractures and deterioration of coal mass properties are also analyzed systematically.

May 1, 2009