Search Documents

By A. Gakwaya, P. Vachon-Joannette, P. Gagnon, J. Lévesque

"Predictive numerical methods are essential tools for reduced development cost and improved high performance designs of modern aircrafts. Their use leads to savings in terms of design cycle time and experimental trials. Composite materials subjected to impact loadings demonstrate various damage modes such as matrix cracking, fiber breakage, delamination and, ultimately, fabric fracture. Composite laminates are extensively used in the aerospace industry, and their damage modeling is complex due to their inhomogeneity and anisotropic behavior. Damage evolution affects both in-service properties and performance of these composites. In this work, the drop-weight impact test has been simulated. Using a material model that accounts for both delamination and intralaminar damage, laminates response is analysed using numerical simulations based on 3-D finite-element models of the commercial code Abaqus/Explicit. Experimental and simulation results are compared, in terms of energy absorption and contact force. The obtained numerical results show good agreement with experimental data.INTRODUCTIONAs primary aircraft structures are increasingly being made from advanced fiber-reinforced polymer matrix composites and are in general exposed to a variety of impact scenarios (bird, hail, debris etc.), an understanding of the impact event and the performance of composite materials during impact is important in the development of new structures. This work is focussed on low velocity impacts that typically occur when foreign objects hit the aircraft during maintenance or other on-the-ground operations. These impacts can cause non visible damage that affect the structural integrity of the composite components. While for metallic structures, damaging impact events typically leave noticeable dents due to plastic deformation, in contrast, for high strength carbon fiber reinforced composites, they can deform elastically to strain levels exceeding 1% and the internal damage can often occur without the formation of a visible dent. The identification and effect of impact damage on the performance of the structure is thus of great concern to the aircraft industry as the durability and damage tolerance of these composite structures are strongly influenced by the size of detectable internal damage."

Jan 1, 2016

By B. Krysa, A. Mitsui, T. L. Koehler

The presence of arsenic, even at trace levels, in copper processing leads to the risk of arsine gas where reducing conditions exist that can reduce any soluble arsenic present to its minus 3 valance state and generate hydrogen gas from the solutions. This risk is understood to be significant within the industry, particularly in the case of liberator cells where copper concentrations in solution are drawn down to remove the copper and impurities from the bleed stream. However, there are numerous other potential areas where the arsine gas risk exists including contact between active metal such as iron, zinc or aluminum and arsenic bearing solutions in pyrometallurgical dust treatment, refining and acid plant operations. In turn this breaks down to different mitigating strategies dependent on the risk scenarios considered; for example, how this risk interacts with Change Management, Confined Space Entry or Contractor Training. The ISO 45001 is an emerging standard meant to improve employee safety, reduce workplace risks and create safer working conditions all over the world. The paper shows a case study of how a framework consistent with the tenets of ISO 45001 has been used to provide a consistent assessment of this risk for a wide variety of copper operations and the expectations of how this may be used to effectively improve the effectiveness of barriers against future incidents. INTRODUCTION Arsine gas (AsH3), first identified in 1775, is a highly poisonous, colorless, non-irritating gas with a mild garlic odor that is heavier than air. Arsine gas is generated when reducing conditions are generated in the presence of hydrogen ions and arsenic compounds. Present permissible occupational exposure limit as defined by Occupational Safety and Health Administration (OSHA) as an 8-hour time-weighted average is ppm (0.2 mg/m3). Further increasing the risk, conventional respiratory protection utilizing half or full masks with gas filtering cartridges provide minimal protection against arsine. In copper processing plants, the risk of arsine generation is well understood in liberator cells, which are part of the electrolysis process. In this process, solutions containing copper are reduced in copper concentration removing not only the copper, but also arsenic, antimony and bismuth. The residual solution can be bled to control impurity build-up in the refinery. In this process, if the copper concentration is reduced to the point where As3- can form, arsine gas is generated via reaction with hydrogen ions generated during the plating process. The copper concentration at which arsine gas is generated depends on copper concentration at the cathode surface, the temperature and the acidity. As a result, there is always a risk of arsine gas generation in the liberator cell. Process measures to minimize or mitigate arsine evolution are tight control on final copper concentration, warm temperatures, fresh feed distribution and internal acid recirculation rates. Operator exposure protection measures are hooding, ventilation, arsine detection systems, restricted personnel access, automated shutdown controls and pre-defined evacuation plans.

Jan 1, 2019

By J. Drozdiak

In this paper we present the results of preliminary investigations into the applicability of new laboratory scale tests for the prediction of operating gap and specific throughput in high pressure grinding rolls (HPGR). The work is a part of the CAMIRO HPGR research program being conducted at the University of British Columbia, which aims to develop a suite of small-scale tests and procedures for the selection and sizing of HPGRs. A focus of the presented study is to test sample types in terms of their terra-mechanics based characteristics and relate them to specific throughput and gap results from pilot HPGR testing on the same samples.

Jan 1, 2012

By Loris S. Pascoli

The increased pace of globalization in the mining industry has presented more opportunities for Canadian service companies to participate in ventures abroad. However, varying cultures, laws, competitive environments and contracting philosophies in other countries make it impossible to take for granted what is normal in the Canadian context. The author discusses some of his experiences and situations encountered in over 30 years in the diamond drilling industry, the last third of which were primarily focused on projects outside of this country.

May 1, 2001

By P. Hale

"The trend to drives of more than 10,000 hp on large-capacity ball and autogenous mills for increased operating efficiency has been limited by factors in the conventional drive system. A solution to this problem, using modern developments in static converter technology, is the concept of driving the mill directly without gearing using a low-speed, low-frequency synchronous motor with a cyclo-converter power supply.This paper presents various practical arrangements of mill and low-speed motors giving the specific advantages of each system. The means of controlling inrush currents on starting and of spotting by the use of variable-frequency control are outlined in general form. Several gearless ball mill drives are scheduled for start-up in European cement plants and further orders have been placed."

Jan 1, 1970

By Paul Graham

Presentation Focus ? What is LTUG / What do we do? ? History of LTUG ? Examples of Benefits from LTUG Participation ? Encourage Participation What is LTUG? ? An informal gathering of surface mining companies to discuss and work issues of common interest and to share information and best practices around large tires.

May 1, 2008

By M. S. Ünal

Creation of 3D model of coal seams is a tedious and time consuming operation. Computer aided 3D solid modelling of coal seams can be performed in a fast and detailed manner. However, in case of having tectonically disturbed coal seams where faults may be observed, expert opinion is necessary to decide the geometry of the coal seam. The aim of this study is detection of fault zones with computers by using drill hole data. Firstly, a digital database is generated by using the drill hole data. Surface models of the layers are produced by applying triangulation method on coal seam roof elevations. The generated surface is divided into small squares and consequently dip and dip direction values are calculated for each square. Variograms for dip and dip direction are determined and maps showing the variation of dip and dip direction are generated by using geostatistical methods such as kriging and co-kriging. Examination of disconformities observed on estimation maps created by kriging and co-kriging clearly reveals the extension of faults. The method used in this study is applied to detect fault lines of a known mine field. 3D solid modelling of the coal seam has also been performed by using conventional cross-section method. The results of both methods were in good agreement. Identification of major faults by using the method introduced in this study could certainly simplify 3D solid modelling of coal seams.

Aug 1, 2013

By T. Scully

Since early days in coal mining, it has been known that some coals and the carbonaceous materials associated with them will heat and fire spontaneously. Many theories have been advanced to account for this phenomenon, but it is only within comparatively recent years that any scientific research has been carried out to determine the causes of this heating, the conditions which bring about its occurrence, and the reason why different coals heat with a varying degree of readiness. So far, this research has not cleared up these points entirely, but a great advance has been made in our knowledge of the matter. In general, any coal will fire spontaneously, although with a varying degree of readiness, provided conditions for its doing so are favourable enough. These conditions are that the coal must be in a fine state of division, that sufficient oxygen must be present for rapid oxidation, and that the air current passing must be so small that it is insufficient to carry off the heat produced by this oxidation. Many other minor factors, however, contribute to bring about spontaneous heating, either by producing initial heat themselves or by inducing the other major conditions.

Jan 1, 1931

By M. Al-Hilal, G. Rajja, A. Al-Ali, Y. Jubeli

Abstract -A radiometric survey was carried out over clastic sediments in the immediate vicinity of some phosphatic sediments of Cretaceous age in the Wadi Qasser Al-Hallabat basin of central Syria. The objective was to explore for uranium and to define its dispersion pattern. This was based on ground radiometric surveys and geological studies. All ground surveys (using radon emanometry, track etching, gamma-ray survey and geochemistry) gave similar results, outlining the locations of the radioactive phosphatic formations in the basin, and indicating the dispersion pattern of uranium in the clastic sediments in the surrounding area. The dispersal of uranium from upper Cretaceous phosphatic formation occurs by mechanical weathering and chemical leaching by oxidizing surface waters. A rough estimate is that about one-third of the original uranium content of the Cretaceous sediments has been dispersed. Mechanical erosion is responsible for the main part of this released uranium, which now occurs in Recent sediments. However, the occurrences of spotty secondary U mineralization indicates that another small part of the available uranium must have been chemically leached out by the prevailing oxidizing waters, forming minor surficial minerals.

Jan 1, 1998

By J. Shanks

In 1920 the writer presented some notes, embodying his experience with storage-battery locomotives as main under-ground haulage-motors at Brazeau collieries. (1) Since that date these motors have stood up well to the test of maximum output and heavy overloads, having accomplished all that was expected of them. The notes presented in 1920 gave a brief description of the conditions under which these motors were working at Brazeau collieries, also the cost, per ton mile, of operating them. The cost per ton mile has since then been appreciably reduced, by working the locomotives nearly to capacity and under more ideal haulage conditions, on both shifts. It is not the intention of the writer to repeat what was written in 1920, but rather to give members the benefit of his experience in operating different types or designs of locomotives; to draw their attention to the drawbacks of some designs, and to the improvements made in some of the more recent storage-battery locomotives put on the market, as regards efficiency, upkeep, and safety. Because of their flexibility storage-battery locomotives have advantages over any other type of haulage, where grades are suitable to their use. The number in use in the mines in the United States has increased enormously during the past few years, and this method of haulage is, at the present time, attracting the attention of British and Continental mining engineers.

Jan 1, 1924

By A. Dolatmoradi

Nanocrystalline structure formations produced by severe plastic deformation in Fe-0.15C with initial ferritic-pearlitic and IF steel with ferritic microstructures have been studied through microstructural observation and microhardness measurements. It was found that the nanocrystalline region first forms near the surface of samples due to localized severe deformation. It was also observed that the nanocrystallization rate of Fe-0.15C and IF steels and the deformed layer thickness in these two materials are different with similar milling conditions. The crystallite size and structural evolution of the samples during milling was studied by employing XRD and SEM.

Jan 1, 2010

By Alastair J. Sinclair, Asger Bentzen

Abstract - A simple linear model for interpreting duplicate analytical data for a range of values is described. The conceptual model can be quantified using a reduced major axis model rather than the inappropriate traditional least squares approach. The reduced major axis parameters (slope, intercept) and associated errors provide a quantitative basis for: (1) defining bias, and (2) comparing results within laboratories, between laboratories and between sampling/analytical methods. Application of the linear model must be preceded by extraction of obvious outliers or small groups of values that have an inordinately large impact on values of the statistical parameters defining the model. In addition, consideration must be directed to the presence of more than one population of sampling error, as in the case of multiple styles of mineralization being sampled.

Jan 1, 1998

By J. F. Harkom

Introduction The importance of the preservative treatment of mine timbers need scarcely be stressed here. Increasing the life of mine timbers will reduce one of the major costs of mining and also conserve the available timber supply which lies within easy access of the mines. When treated, several species of timber may be used which otherwise could not be considered, owing to their short life. Another feature which should appeal to the mining industry is that wood preservatives are a mine product, and the benefit to be derived from the increased consumption of wood preservatives due to the example set by mine owners is not inconsiderable. Mine timbers may be divided into three classes when considering preservative treatments. (1) Timber obviously not profitable to treat owing to long natural life or short period of time in service. (2) Timber that obviously should receive protection from decay. (3) Timber installed in locations where the length of service required will depend on future developments, so that preservative treatments might or might not prove to be a profitable investment.

Jan 1, 1930

The Cadia mine is shifting from the open pit operation to the Cadia East underground block cave. The resulting increase in milled tonnes and the decrease in fines production through shifting to block caving require an increase of over 25% in installed power. This expansion is being accomplished via the installation of up-front crushing and HPGR milling of the ore, with the SAG mill receiving a secondary crushed feed. This design, criteria and rationale for selection is presented. Over the coming years, the mine will further expand capacity. The target is to accomplish this with minimal addition of installed power or use of fresh water. This presents a challenge that epitomizes the future constraints on our resource dependent and intensive industry. The approach and proposed options to this longer-term expansion are also presented.

Jan 1, 2012

By A. Tohn, L. May, Adham. K.

The path from process conception to commercial implementation poses significant technical, economic, and sometimes political challenges for every project team. Solving the technical challenges typically distinguishes successful projects from those that fail. Here, the authors provide an outline for technical success based on lessons learned from years of experience in process design and R&D. Challenges faced by new technology developers, with regard to design and definition, are described. Experience-based methods to avoid missteps are shared. Special emphasis is placed on the selection of viable unit operations, definition of known and unknown parameters, experimental screening of options, and piloting for scalable design information. Use of computational models to define, assist, and interpret the pilot operations and results are described. Furthermore, the value of active collaboration amongst the design, research, and owner team is demonstrated.

Jan 1, 2011

By Robert MacPhail, Louis Racine, Bret G. Cousins

"Sodium Isopropyl Xanthate is employed in a wide variety of sulphide flotation procedures due to the specificity over other xanthates and the cost savings over other sulphide collectors such as thionocarbamates, xanthogen formates and dithiophosphates. An investigation carried out by Tennants Research Technology Applications (TRTA), has produced a chemically enhanced SIPX that has shown all the advantages of normal SIPX along with improved recoveries.Currently, FLEX 31 is manufactured at the Prospec Chemicals xanthate plant in Fort Saskatchewan, Alberta, Canada. Prospec, founded in 1983, produces approximately 4500 tonnes of xanthates per year and is presently undergoing expansion to produce approximately 6000 tonnes. The proprietary process for FLEX 31 is a new addition to plant operations that include the production of xanthates, thionocarbamates and xanthogen formates.This paper will cover the testwork on the zinc flotation circuit at the Louvicourt Mine in Val d'Or, Quebec. This testwork indicated that FLEX 31 could replace SIPX due to the ability of the FLEX to improve zinc flotation kinetics without adversely affecting final concentrate grade. FLEX has presently replaced SIPX in the zinc circuit at Louvicourt.BackgroundThe Louvicourt deposit is hosted by greenschist facies Archean volcanic rocks located in the southeast portion of the Abitibi Greenstone Belt. In the Val d'Or area, the volcanic rocks form an east-west striking, steeply dipping and south-facing sequence composed of thick mafic and ultramafic flows of the Lower Malartic Group.The joint venture has three partners-Aur Louvicourt Inc. (30%), Novicourt Inc. (45%) and Teck Corp (25%). Aur Resources holds 30% interest through Aur Louvicourt, a wholly owned subsidiary and is the operator of the project. Novicourt Inc. is 60.9% held by Noranda.Approximately 75% to 85% of Louvicourt's revenue comes from the sale of copper; 10% from gold (in the copper concentrate); 7% from zinc and 3% from silver (also in the copper concentrate) The copper at Louvicourt is fairly ""fast floating"". About 60% of the copper in the ore can be concentrated in the first flotation cells with feed grades of approximately 4% copper.The initial testwork and pilot trials had indicated that it would be difficult to achieve zinc grades over 52% and recoveries would have to be kept at a level amenable to salable concentrate grades. The actual mill results, with a fine regrind, achieved zinc grades of 55% to 56% at about 75% recovery."

Jan 1, 1996

By George Booth

In mining operations the cost of timber is an item of much importance, because the life of mine timbers is, in many cases, very short and, as the supply of the better grades becomes depleted, less durable kinds must be used. This, of course, tends to shorten still further the period of service-ability. While it is possible that concrete and steel may, to some extent, take the place of timber in mines, their high initial cost and the difficulty in installation will greatly restrict their use. Moreover, wood, besides being comparatively cheap to handle, possesses other desirable qualities, and for many purposes a satisfactory substitute is hard to find. Both the decreasing supply and the increasing price of timber make its more efficient utilization imperative. AGENCIES DESTRUCTIVE TO MINE TIMBERS Timber used in mines is exposed to destruction from many sources. Wear, breakage, and waste are responsible for much loss. Wood rollers and drum laggings must be frequently replaced on account of the constant wear by ropes. Unprotected timber in chutes and mills is also rapidly worn by abrasion, and track ties in main haulage ways get worn by the feet of mules, cut by ropes, etc. Large amounts of timber are broken by 'crush' and 'squeeze,' and much temporary timber is buried beyond all recovery in pillar workings and in those mines which resort to back filling. Decay and insect attack, however, cause the greatest damage. If not totally destroyed by one or both of these, the timbers frequently become so weakened that they break under the pressure upon them.

Jan 1, 1926

By S. C. Bouffard

Barrick's Zaldivar operation in Chile produces copper by heap leaching, solvent extraction, and electrowinning. The heap consists of a dynamic pad, and its stacking and operating conditions have changed over its 11 years of operation. These changes have included pad re-mining midway through the cycle, tightening of the irrigation drip lines, an increase of the coarseness of the particles, and an increase of the heap height. This paper reviews the heap operating data to understand the effects of these changes on the kinetics and recovery of copper minerals. Field tests demonstrated that neither re-mining nor tightening the irrigation grid added value for both low and high grade oxide and sulfide ores. The P80 of the feed ore was increased by 0.8 mm, which did not reduce the copper recovery of oxide and sulfide ores. The increase of the heap height above 8 m lowered moderately the copper recovery from sulfide minerals, and very slightly the recovery from oxide minerals. Despite the lower recovery, the higher tonnage stacked in the taller heap increased the copper output. Optimizing the chemistry of the agglomeration and feed solution holds more promise for increasing the copper recovery than the above physical changes.

Jan 1, 2007

By Zhanyou Huang

The logic and capabilities of a short-term planning tool are presented. It was developed using mixed integer linear programming (MILP) techniques to solve the open-pit and underground mine planning problems that include multiple mining areas, multiple processes, multiple destinations and blending requirements. It finds the optimum schedule that achieves the objective while satisfying comprehensive product quality and quantity requirements, equipment utilizations, as well as physical and technical constraints. A case study is given to demonstrate its applications.

Oct 1, 2009

By Zhanyou Huang

The logic and capabilities of a short-term planning tool are presented. It was developed using mixed integer linear programming (MILP) techniques to solve the open-pit and underground mine planning problems that include multiple mining areas, multiple processes, multiple destinations and blending requirements. It finds the optimum schedule that achieves the objective while satisfying comprehensive product quality and quantity requirements, equipment utilizations, as well as physical and technical constraints. A case study is given to demonstrate its applications.

Oct 1, 2009