Search Documents

By Walter Kaeck

In a recent upgrade of their system, Amtrak converted a bascule type draw bridge over the Thames River to a vertical lift structure supported by the existing piers. During the bridge replacement, significant settlement occurred on one of the piers and movement continued thereafter. Construction was stopped as Amtrak became concerned as to how much the subsequent construction activities would cause the pier to further settle and tilt, not only impacting the operation of the existing bridge, but also jeopardizing the new lift span. Mueser Rutledge was engaged at this time to help understand and solve the problem. A remedial grouting program was developed to arrest the settlement. As a subcontractor to Cianbro Corporation, Pittsfield, ME, The Judy Company was hired to perform the remedial grouting work. Work platforms were constructed around the pier for support of the drilling equipment. A dual string drilling system was used to install sleeve pipes at depths of up to 185? below the water level. Ultrafine cement grout stabilized with additives was placed at 2.5 foot intervals through the depth of the sand and gravel stratum below the bottom of the pier. Logistics were difficult and the schedule was severely impacted by the remedial work, necessitating working six 12-hour shifts per week and working in the river through the winter months. After four months of drilling and grouting, movement of the pier stopped. At the conclusion of the remedial work, more than a million gallons of ultrafine cement grout were placed. Confirmation borings recovered completely solidified material with compressive strengths ranging from 500 to 1500 psi. The bridge replacement was then completed and is functioning. Continued monitoring through July 2009 shows negligible movement.

Jan 1, 2009

By Don W. Dotson

In 1962, Kondner prepared several papers dealing with hyperbolic stress-strain response of cohesive soils. The following year, Brinch Hansen proposed 80% and 90% failure criteria for stress-strain behavior of cohesive soils. Fellenius was instrumental in popularizing these failure criteria for pile load tests and offered a direct solution equation for the failure load according to the 80% failure criterion. Since the 90% Criterion has been incorporated into the International Building Code, equations for the direct solution of the failure load at the 90% Criterion would be useful to practicing engineers. This Technical Note supplies the derivation methodology for the 80% Criterion and provides expressions to determine the load and deflection at failure for the 90% Criterion.

Aug 1, 2013

By Jamey Rosen

A Project Information Management System (PIMS) was developed to manage and analyze QC data at the Herbert Hoover Dike Rehabilitation Dam Modification Cutoff Wall (owned by the Jacksonville District of the United States Army Corps of Engineers). A special feature of this PIMS was its geospatial component. Data collected from Bauer drill rigs were automatically “geoprocessed” into threedimensional features representing the predrill, jet grout, and Cutter Soil Mixing panel elements, as well as calculated verticality and overlap metrics. These features were visualized in interactive planimetric, profile, and 3D views that facilitated several quality control activities during the project.

By Lance Helwirg

New high and low double outfall bridge structures for a juvenile fish bypass system have been constructed on the Washington Shore approximately two miles downstream from the Bonneville Dam on the Columbia River. The high and low outfalls each extend approximately 400 feet into the river from the Washington shore and are designed to release juvenile salmon into the river at above-water discharge elevations for improved survival rates. The two outfall structures include post-tensioned concrete double box flume girders approximately 7 feet high by 13 feet wide, which will be submerged in river flows as high as 15 feet per second. Each of the 6 offshore foundation piers is composed of a single 10-foot diameter reinforced concrete drilled shaft with a permanent steel casing embedded into the river bottom approximately 100 feet. Challenging outfall design conditions included designing the entire structures to be submerged for long periods of time in 15-feet-per-second river water flow with a 60-foot cantilever at the end of each outfall, and with the superstructure 70 to 80 feet above the river bottom. Figures 1-1,1-2, and 1-3 show the high and low outfall structure overhead photos and elevation view.

Jan 1, 2001

By Paul J. Lewis

Estimation of the axial side shear resistance of drilled shaft rock sockets is directly related to the unconfined compressive strength of the bedrock. Commonly, the mean unconfined compressive strength value is calculated from a range of laboratory test results and is used to estimate the side shear of the bedrock. This paper presents the results from a full scale axial load test performed on an 8.5-feet-diameter drilled shaft rock socket, and compares measured side shear values to estimated values for two different rock strata. Measured side shear values correlated well with the design value calculated for the ?strong? rock stratum, but did not correlate well with the design value calculated for the ?weak? rock stratum. The mean unconfined compressive strength was used to calculate the side shear in both strata, but review of the laboratory data indicates that this value may not have been appropriate for the weak stratum due to a large variation in the laboratory test results. Also included in this paper is a discussion of the subsurface conditions, the laboratory test results, and the methodology used to design the drilled shaft rock sockets for axial and lateral resistance.

Jan 1, 2013

By Nils Schneider, Marc Peters, Stefan Frey, Andrea Fluck

Due to the worldwide population growth, the development of sustainable infrastructure and the exploration of renewable energies plays a key role to handle the rising megacity trends and to limit carbon footprint. Herrenknecht AG is a leading manufacturer of Tunnel Boring machines and has constantly endeavored through its extensive Research and Development programs to address limitations faced by the civil engineering industry as regards to construction equipment capabilities. New mechanized technologies, mainly coming from the tunnelling industry, have been developed by Herrenknecht AG as an efficient alternative to conventional civil engineering, where tailor-made concepts are required to comply with restricted conditions onsite. Very often this innovation led technology capability has meant making construction processes safer due to minimal human intervention and also far more productive due to higher performance as compared to other latest or conventional methods of construction. The rising need for even higher building structures and large-capacity bridges involve the development of innovative deep foundation technologies for on- and offshore operation. Conventional methods like bore piles reach their technical and economic limits under certain conditions. For building shafts and foundations, the mechanized Vertical Shaft Sinking Machine technology (VSM) from Herrenknecht AG is a proven innovation and has now been used in various onshore infrastructure projects worldwide to construct a total of 94 circular shafts in depths of up to 115 meters. It operates below the groundwater level, completely remote-controlled from the surface in a diameter range from 4.5 to 18 meters. Subsequently Herrenknecht noted that Offshore foundations, especially in non-drivable ground conditions such as soft and hard rock (e.g. limestone, sandstone, mudstone, granite etc. or soft soil with high density) and shallow continental shelf (water depth approx. 20-60m), presented construction challenges and equally an opportunity for building high performance equipment. The latter construction conditions usually requires drilled installation methods for applications such as harbor enlargements, bridge foundations and foundations for offshore wind turbines. The Offshore Foundation Drilling technology (OFD®) is Herrenknecht’s latest innovation, incorporating our learnings from the VSM and full-face Tunnel Boring machines, and the OFD® enables a rapid and economical offshore installation in such variable ground and rock conditions. This paper will discuss the technology behind the new mechanized technology of VSM and Herrenknecht’s latest innovation of the OFD® along with their respective application fields in foundations construction. The paper will further present in details, their range of benefits to the construction industry.

Nov 1, 2022

By Venugopal Bonani, Kumaran M., Thomas John

Liquid storage tanks are usually located in nearshore or coastal regions with soil profiles containing thick layers of compressible soils. These storage tanks are usually of large diameter up to 90m and carry high loads, and the tanks are supported by heavy deep foundations such as piles. These structures are subjected to huge lateral loads due to wind and earthquake, and any damage to storage tanks with highly inflammable liquids leads to disastrous condition. So, it is important that the top layer of soil (up to the fixity depth) should be strong enough to provide the required lateral load capacity to the pile. In a project for constructing LNG terminal in Odisha containing 2nos of 89m diameter LNG storage tanks supported with pile foundation located near to coastal region, for improving the lateral capacity of existing soil, the top 3m was replaced with compacted engineered fill (GSB). The site was a filled-up area with dredged soil from seabed, the top 5m-10m were soft to medium stiff clay with SPT N less than 10. The lateral design load on pile was 534kN under free head condition. Actual lateral capacity for the strata was around 200kN under free head condition which was less than required capacity as per structural requirements. Therefore, for improving the lateral capacity of pile the top 3m soil is replaced with well compacted engineered fill (GSB) in layers of 150mm and the capacity is proved by conducting initial and routine lateral load tests. This paper describes the properties of the engineered fill used and how the lateral load capacity of pile was improved to meet the design requirement.

Sep 1, 2022

By Sandeep Pattnaik

Spring stiffness of soil and rock at different depth is often required for a pile structural model. If the pile is rested in multiple layers of soil, then it is rather more complex to simulate the soil in a structural model. The spring stiffness will vary based on density of soil strata over the depth. When a pile is socketed in weathered rock followed by a soil layer, a sudden change in subgrade modulus can influence the pile deflection drastically. Determination of soil spring and simulation of the pile in this condition required correct interpretation of subgrade modulus. The conventional approach of pile spring calculation underestimates the spring stiffness by ignoring underlaying stiffer layers. A finite difference method (FDM) of analysis can reasonably estimate the p-y of soil / rock based on subgrade modulus of each layer. However, the transition between the layers can be better simulated as per the deflection pattern of the pile. The lateral deflection of the pile is mainly dependent on the stiffness of soil layer surrounded by the pile. Generally, the lateral influence of a pile varies from 4D to 6D depending on the soil type. Therefore, soil spring stiffness around the pile would require special attention of a Geotechnical engineer to avoid uncertainty in the prediction of pile behaviour. In this paper, emphasis has been given to develop an approach for pile spring stiffness design. A standard software program LPile has been used to develop p-y curves of soil and rock layers at different depths and then converted to soil/ rock springs over the depth. Modulus of Subgrade Reaction as given in IS 2911 (Part2) was also used to correlate the spring value for different type of soil. Obtained analytical results were compared with full scale field trial for lateral deflection of pile. A good agreement between these two approaches has been established. The effect of soil structure interaction in the structural model shall be simulated by assigning an equivalent vertical and horizontal soil spring, which is developed by Winkler’s soil spring approach. A simplified design principle for calculating the pile spring is discussed in this paper. This approach has been extensively used in Mumbai metro elevated line pile design.

Nov 1, 2022

By Piotr Kozlowski, Stanley L. Worst, Matthew J. Niermann

The Waterman Hospital in Tavares, Florida was undergoing an expansion and required a below-grade excavation immediately adjacent to the Emergency Department. This wing of the hospital was under high traffic and required uninterrupted access for ambulances as well as helicopter landings. The below-grade expansion was also next to a part of the hospital which did not have a basement. Tiedback soldier beams and wood lagging were used as the earth retention system where the shoring line was not immediately adjacent to the existing structure. Structural jet grout underpinning was used to support the existing building and to serve as the earth retention system in the more sensitive area. Jet grout underpinning was chosen to minimize movements, loss of ground and settlement of the structure which was bearing on clean sand deposits. This paper will discuss the design, quality control and construction of jet grouting and its application to this project. INTRODUCTION Project Background The expansion of the Waterman Hospital included an addition to the Emergency Department. This addition was located adjacent to the existing hospital building in a congested area with limited access. The north side of the addition was bordered by the ambulance drop-off area. The south side of the addition was bordered by the helipad landing area. Both areas had to remain open and fully accessible 24 hours a day, 7 days a week.

Jan 1, 2019

By Clif Kettle

The paper will detail the design and execution of passive and active settlement control measures, the means adopted to overcome the various physical and operational constraints, and to meet specified allowable settlement criteria. The paper will highlight the close integration between the tunnelling and geotechnical contractors, designer, and Client, and demonstrate how particular practical difficulties were overcome by both the design and the construction methods.

Jan 1, 2008

By R. Bruce Patterson

The New Tacoma Narrows Bridge is a classic suspension bridge founded on concrete caissons. Caisson construction was complicated by the proximity of the existing bridge piers, only sixty feet away. High capacity plate anchors were used successfully to moor the new caissons in currents as strong as seven knots during construction.

Jan 1, 2013

By Helene Kennedy, Josef Macsik, Yvonne Rogbeck, Gregory Makusa, Göran Holm

"Constructions activities in cities often imply large volumes of surplus material which could be treated by stabilization for re-use in new geotechnical constructions. Modification of dredged sediments by e.g. stabilization/solidification (s/s) is an example of sustainable handling option implying dredged contaminated sediments to become a potential resource for civil engineering constructions. The SMOCS project (Sustainable Management of Contaminated Sediments) within the Baltic Sea Region Programme 2007-2013 has developed a guideline based on a sustainability approach free to download at www.smocs.eu. The paper presents key issues in the guideline and highlights the importance of performing a field test as part of the design process. Two field tests with s/s-treated dredged sediments for new port areas are presented. Strength, permeability and leakage properties of s/s-treated contaminated sediments make beneficial use in geo-constructions possible. The influence of possible physical/chemical deterioration processes on the durability has been studied showing that freeze/thaw cycles might degrade the monolith of s/s-treated sediments. Consequently s/s-constructions shall be below freezing depth. Other deterioration processes such as salt and sulfate penetration were found of minor importance. Research is on-going to study the influence of and how to cope with freeze/thaw cycles on the long-term properties.BACKGROUNDConstructions activities in cities often imply large volumes of surplus material which could be treated by stabilization for re-use in new geotechnical constructions. The mechanical and environmental properties of the contaminated sediments could be modified through the stabilization/solidification method (s/s method) and provide a potential resource for civil engineering constructions. The SMOCS project (Sustainable Management of Contaminated Sediments) within the Baltic Sea Region Programme 2007-2013 has developed a guideline on management of contaminated sediments based on a sustainability approach. A field test on the application of the stabilization/solidification method for treatment of dredged soft contaminated sediments was implemented in the Port of Gävle, Sweden. The treated sediments were beneficially used as fill material in the new port area replacing ending natural resources."

Jan 1, 2015

By Frederick C. Rhyner

The United States government sponsored the construction of a new vehicular bridge over the Diyala River in Bubriz, Iraq. This paper describes the geotechnical engineering for design and construction of drilled shaft foundations for this bridge. An Iraqi geotechnical engineering firm made borings and laboratory tests while analysis and design recommendations were provided in the United States. Despite the severe challenges of engineering in a war zone, excellent cooperation was the key to a successful effort. Three drilled shafts designs were necessary to accommodate the different subsurface conditions: a) medium-compact to compact sands, b) stiff to hard clays and c) mixed soil profile. The alpha and beta methods were used to estimate capacities for a conservative design, recognizing that quality control during construction might be less than what is normally provided in the United States. Iraq has a high seismic risk and LPILE was used to estimate the drilled shaft response during earthquake loading conditions. Settlement estimates were made using FHWA methods. Construction was carried out entirely by local Iraqi firms, despite the challenges of working in an active conflict area.

Jan 1, 2009

By A. Ortigão, M. Felix, E. Falk, T. Koehler

"Ground improvement techniques such as vibro-replacement or deep soil mixing are fairly young products in the Brazilian geotechnical market. Soft soils in this country are deep, very soft, have low sensitivity and are challenging. In general, ground improvement techniques are increasingly selected as more costefficient and flexible solutions on infrastructure projects compared to the conventionall technologies such as piled embankments, wickdrains with surcharge or jet-grouting. The geotechnical challenge expansion project for the Porto Alegre Airport, South Brazil, involved a taxiway area of five ha of 8 to 10 m of soft clay deposit. The deep soil mixing (DSM) technique was selected as a cost-effective solution to reduce settlements. As part of the design, an extensive soil investigation programme includ ing laboratory and field trials was carried out to define the most economical slurry-recipe, DSM installation patterns and quality control specs. This paper gives details of the field and laboratory trials and present results.INTRODUCTIONThe International Airport of Porto Alegre in the state of Rio Grande do Sul in Brazil is located in an area with extensive sediments near to Guaíba Bay. During the different construction phases of the airport over the last decades, the soft clay deposits have been a challenge for the local geotechnical community as well as for the specialized contractors (Schnaid et al, 2001). As part of the most recent expansion scheme, a cargo-terminal with a five ha airplane tarmac area will be constructed."

Jan 1, 2015

By S. Y. Fantaye

This paper discusses the design, construction and performance of a 30 inch thick diaphragm wall recently constructed in Baltimore, Maryland at Inner Harbor East. The project site is an established marina and waterfront property. The geologic profile consists of fill, alluvial silt and clay, Potomac sand and clay, decomposed rock, and weathered rock on top of gneiss bedrock. The approximately 1,300 ft long perimeter diaphragm wall serves as a water cut-off, perimeter basement wall and support of excavation for the high rise project?s five levels of below-ground parking. Due to the fast track construction and the tight schedule, the initial design of the diaphragm wall was based on a limited amount of geotechnical information. Supplemental borings were then performed along the alignment of the wall to verify the design assumptions and wall depths. Additionally, the design criteria required that the wall be keyed into a competent stratum with low permeability. The Engineer of Record for the diaphragm wall, Mueser Rutledge Consulting Engineers (MRCE) completed the design and produced accelerated construction documents allowing the developer to release the drawings early for bid. This paper describes the theoretical soil parameters used to develop the loads, moments, and shears for the design of the diaphragm wall and the temporary tieback anchors. It also discusses the refinement of these soil parameters using the observed wall displacements and tieback pre-stressing forces as a baseline. This paper compares the calibrated parameters to the values used in the design of the wall. It explains how the soil structure interaction model was developed and the soil parameters calibrated using PLAXIS 2D non-linear finite element software. The paper also discusses the use of the proprietary CWS joint by Soletanche/Inquip JV as end stop between consecutive wall panels and the unique top-down construction utilized to support the diaphragm wall at the Southeast double re-entrant corner.

Jan 1, 2008

By Mike Muchard

A design phase load test program was performed at the Broadway Viaduct bridge site to evaluate load carrying capacity and constructability of post grouted drilled shafts. The program included construction, instrumentation, post grouting and load testing of three drilled shafts. Two shafts included sleeve port and plate base grouting apparatus and were post grouted. The third shaft was un-grouted and served as a control shaft for comparison of the un-grouted end bearing. The shafts were 5 feet in diameter with the control shaft at 55 feet in length and post grouted shafts at 55 and 66 feet. SPT borings at the centerline of each test shaft defined geotechnical conditions at each shaft. Test shafts were instrumented with strain gages and concrete integrity was evaluated with crosshole sonic logging. Instrumentation and data acquisition was used during the post grouting operation to fully capture the shaft behavior. Finally, Statnamic load testing was performed on all three shafts to their ultimate capacity. The fine to coarse sandy soils in which the shafts were tipped in were well suited to improvement from post grouting. Grout pressures of 660 psi were achieved with 0.08 inch or less of upward shaft movement. Subsequent Statnamic load tests showed 183 to 192 percent greater end bearing in the post grouted shafts as compared to the un-grouted shaft. The overall result showed a potential savings of approximately 9 feet to 35 feet of drilled shaft length in addition to the increased quality assurance from post grouting.

Jan 1, 2009

By V. A. Sernov

"One of the ways to increase the bearing capacity of a piled foundation is to take into account soil resistance in the base of the raft. Piled raft is similar to shallow foundation and can transfer significant part of the load into the base. It allows reducing number of piles in the foundation or shortening their length. As a result building terms and foundation costs reduce considerably. However, nowadays in Belarus there is no reliable and suitable in design practice methods of calculation of piled-raft foundations. In order to devise such methods we have analyzed the results of piled foundation tests fulfilled by various authors up to date and have carried out series of field and laboratory investigations in Minsk. The most important results of the investigations are provided in the article. Methods of analysis of piled-raft foundations are described.INTRODUCTIONPile foundations of late years are used extensively in connection with the increased number of storeys and load increment on the soil. Often pile foundations are applied in comparative favorable ground conditions at the surface of the base. In such cases the increase of the bearing capacity of foundations and the reduction of construction cost are questions of primary importance for designers. One of the ways to increase the bearing capacity of a piled foundation is to take into account soil resistance in the base of the raft. Piled raft is similar to shallow foundation and can transfer significant part of the load into the base. It allows reducing number of piles in the foundation or shortening their length. As a result, building terms and foundation costs are reduced considerably. However, nowadays there is no reliable and suitable in design practice methods of calculation pile foundations with bearing rafts. In order to devise such methods we have analyzed the results of piled foundation tests fulfilled by various authors up to date and have carried out series of laboratory and field investigations.Long before the constitution of the first piled-raft foundations in the Soviet Union there were attempts to consider soil resistance in the basis of isolated and strip grillages. Such bases can be considered as separate fragments of the piled-raft foundation. Prof. A. A. Bartolomey had tested more than 70 pile foundations of natural size in different ground conditions. The length of piles was 3 12 m (?????????? 1995). The observed results show that the raft carries about 10 12% of the total load applied when length of piles is over 9 m and space between piles is a=3d. Bearing capacity of the raft is about 35 40% when the length of piles is 5 8 m and a=6d. Prof. Golubkov has tested 2 prismatic piles (cross section: 350x350 mm, L=3800 m) and 2 pyramidal piles (cross section: head - 600x600 mm, foot – 100x100 mm, L=3000 m). One of the piles was tested with a raft and the other one without a raft. Significant influence of the raft on total bearing capacity was determined, the more the settlement was the more it influenced on the raft. Bearing capacity of the raft was 27,5% in foundation with prismatic pile and 42% with pyramidal pile (???????? et al. 1971)."

Jan 1, 2016

By Arash Khosravifar

One of our research thrusts at Portland State University (PSU) centers on developing design guidelines for pile foundations in liquefiable, laterally spreading grounds. This research has been primarily sponsored by the DFI Committee Project Fund (CPF) program through four awards, totaling nearly $240,000 in financial support. DFI contributed half of this financial support, while the other half was contributed in-kind by PSU and DFI Project Advisory Board members. Leveraging the CPF funds, we secured an additional $550,000 in financial support from the National Science. Foundation (NSF), which has enabled our research group to continue exploring this topic and contributing to the broader engineering community's understanding of the behavior of pile foundations in liquefiable soils. The CPF funds have fostered collaborations with practitioners and researchers beyond PSU. Notable examples include collaborative research involving data from five large-scale centrifuge tests on pile-supported wharves by Steve Dickenson, Ph.D., New Albion Geotechnical; Nason McCullough, Ph.D., Jacobs Engineering and Scott Schlechter, Geotechnical Resources, as well as 1-g shake table tests of bridge pile shafts conducted by Professors Ahmed Elgamal, Ph.D., and Ahmed Ebeido, Ph.D., of the University of California, San Diego. In addition to these collaborations, our research has benefited from industry-university partnerships formed through the involvement of DFI Project Advisory Board members. Their support and feedback ensure that our research products are practical and imple- mentable in real-world projects. The impact of the CPF funds extends to supporting graduate students' theses, which were the basis for 17 technical publications. Some of these publications are expected to have a significant impact on the industry. For instance, our 2018 DFI Journal paper, co-authored by former master's student Jonathan Nasr, cur- rently with the Army Corps of Engineers, has been cited in the 2022 British Columbia Supplement to Canadian Highway Bridge Design Code S6:19. A noteworthy product of our study is a step-by-step design procedure for pile- supported wharf structures subjected to the combined effects of lateral spreading and inertial loads, outlined in a 2022 American Society of Civil Engineers' (ASCE) Journal of Geotechnical and Geo- environmental Engineering paper co- authored by former doctoral student Milad Souri, Ph.D., PE, Geotechnical Resources.

Nov 1, 2023

By Florian König

It is well known that the bearing capacity and stiffness of displacement piles may increase significantly with time, a phenomenon usually referred to as set-up. In cohesive soils the set-up is commonly explained by consolidation processes in which the dissipation of the excess pore pressures around the pile leads to an increase in effective radial stresses. Recent case histories show that set-up may also occur in sand over a period which exceeds by far the consolidation process. Therefore, other effects apart from the dissipation of excess pore pressures must contribute to this long-term set-up effect. This paper presents the results of a series of multiple pile load tests on prefabricated concrete piles which capture the effect of pile set-up empirically. The main characteristics of the set-up trend are shown with respect to soil type, pile dimensions and distribution over the pile length. Possible reasons for pile set-up like consolidation and stress relaxation after the end of driving are examined using a finite element model which simulates the pile installation process.

Jan 1, 2006

By Maurizio Siepi, Paul van Horn, John Coupland, Julian Crawley

"TTMJ is the acronym for the Slurry (Diaphragm) Wall Tension Track Milled Joint currently in development as part of the European Union's innovative and far-reaching Horizon 2020 initiative (FTI Pilot-2015-1 720579). The TTMJ Project has been specifically set up to deliver this versatile new step-forward in Slurry Wall technology. The TTMJ System is protected by patent in Europe and the USA, and is currently under development by a consortium comprising Trevi SpA (Italy), Arup (Netherlands) and CCMJ Systems (UK). The principles of the TTMJ System together with the installation process are herein described in general terms. The system is still under development with field trials scheduled for early 2018, so some of the detail will not be disclosed at this stage. It is the intention of the Authors that the results of these field trials and a more complete description of the System will be presented in a paper we intend to submit for the DFI/EFFC International Conference on Deep Foundations and Ground Improvement to be held in Rome, Italy in June 2018. The final section of this paper explains how the TTMJ system can be applied to a common application of slurry wall construction; deep circular or multi-cell shafts. The system can be used to construct shafts more easily and at less cost than current methods. It also allows shafts with smaller internal dimensions to be constructed than is currently practical.INTRODUCTIONCCMJ Systems (UK) realised that an innovative new approach to forming joints in both Slurry (Diaphragm) Walls and Secant Pile Walls would provide greatly improved joint integrity to greater depths, to the overallbenefit of retaining wall quality, across the world-wide foundations industry.In particular this new system is designed to:??Increase the effective depth range of Slurry Walls (especially walls excavated by grab) and Secant Walls??Remove the requirement for Stop-ends or Joint Formers??Allow for a Shear Key at the joint??Allow for a Water Stop to be installed at the joint??Permit Continuous Reinforcement across the joint??Optimise Reinforcement Density and hence Concrete Flow??Facilitate joints in corner panels eliminating the need for “L” shaped cages and reducing largesingle-pour concrete volumes and slurry storage capacity requirements.??Enable the construction of smaller-dimensioned square and circular deep shafts (especially useful for city-centre sites) than is possible with current methods.CCMJ Systems approached other industry specialists with a view to forming a development team to explore the possibilities for this new technique."

Jan 1, 2017