Search Documents

By L. Gao, X. Gui

Fine coal obtained from Kailuan mine served as the processing object of this study. This material was difficult to separate. A flotation rate experiment was designed to investigate the process distribution characteristics of size and density during fine coal flotation. Size and density analyses of five clean were studied. The mineral morphology of flotation rate experiment cleaning was observed through scanning electron microscopy. The fractions -0.074+0.045 mm and -0.045 mm exhibited the best practical floatability and presented the highest combustible body recovery rates, but the selectivity and natural floatability of these two fractions were the worst. The - 0.074 mm fraction has contaminated the clean coal from the early stage of flotation, and the cumulative clean coal ash of -0.074 mm reached up to 17.20%. The low and middle-density classes displayed varying flotation behavior, but the flotation yield difference was only nearly 3%. The middle-density class caused the clean coal to have high ash content. The poor selectivity of fine coals, middle-density fraction, and fine mud resulted in high-ash clean coals during flotation. Thus, improving the selectivity of fine coal, restraining the flotation of fine mud, and grinding the coal to decrease the middle density mass fraction to liberate clean coals can yield high-quality clean coals through flotation.

Jan 1, 2014

By Rodney J. Hundermark, Sharif Jahanshahi, Shouyi Sun

"The major platinum producers in South Africa make use of electric furnaces for the melting of platinum group metal (PGM) bearing nickel – copper concentrates. To gain better understanding of the furnace operation, research was conducted at CSIRO Minerals in Melbourne, Australia. One aspect of the research project was the investigation of the factors affecting the electrical conductivity of melter type slags.Electrical conduction in slags can occur through two mechanisms: ionic and electronic. There is good understanding of the ionic mechanism. In slags containing high levels of iron, the dominant mechanism is electronic as a result of charge hopping (electrons or holes) between ferric and ferrous ions. There is limited understanding of the electronic mechanism and one of the aims of the research was to investigate this mechanism further.Experimental work was carried out at 1450 °C on Al2O3–CaO–FeOx–MgO–SiO2 slags similar in composition to the melter slags (typical composition range (wt%): Al2O3: 5, CaO: 5-15, FeOx: 10-30, MgO: 15-25, SiO2: 40-60). The approach was to vary the oxidation state of three different basicity slags and measure the conductivity response. The slags had molar (CaO+MgO)/(Al2O3+SiO2) ratios of 0.43, 0.64 and 0.94 and FeOx contents of up to 40wt%. A twoelectrode technique was employed with a shallow layer of slag contained in a magnesia crucible. The small amount of slag facilitated relatively quick equilibration (up to one hour) with the gas atmosphere. Experiments were typically started in air and sequentially reduced using different ratios of CO and CO2 gases.Conductivity increased with increasing basicity and increased significantly with iron oxide content. Above 20wt% FeOx, electronic conduction was significant and the conductivity varied with the oxidation state of the slag. The typical response of the conductivity to the change in oxidation state was the following: starting in air, as the slags became more reduced, the electrical conductivity increased to a maximum at around pO2 = 10-7 to 10-4 atm and then decreased with further reduction. The value of the pO2 at which the maximum occurred was dependent on the total iron oxide content and basicity of the slag. The magnitude of the conductivity of the slags increased with increasing FeOx content in a range of 20 to 170 S/m for 20 to 40wt% FeOx. For a given FeOx content in the slags, the oxidation state dependence of the conductivity varied with slag basicity. The trend observed was that the maximum in the conductivity occurred at higher oxygen partial pressures for the lower basicity slags."

Jan 1, 2003

By Xingshi Yang, Ghislain Bournival, Seher Ata

"Particle-laden interfaces are a fundamental research topic in froth flotation since the process involves particle-coated bubbles in both the pulp and the froth phase. In most experimental studies the characteristics of the particle layer in multi-bubble systems are poorly defined. An experimental setup has been developed based on a Langmuir-Blodgett (L-B) trough. The modified trough allowed introducing an air bubble beneath the particle monolayer formed at the air-water interface which made the study of the interaction between the bubble and the monolayer under various pH values possible. The monolayer characteristics of the particles were also studied and compared in terms of surface pressure (?-A) isotherms and packing factor. On compression, the particles formed branched structure at high pH whereas a uniform monolayer was formed at lower pH. Observations related to the behavior of particles during compression and expansion cycles, and the coalescence of a bare bubble with the flat particle laden interface were provided and the implication of the results for flotation process was discussed.INTRODUCTIONFroth flotation is known for its versatility and ability to concentrate low-grade, complex ores. It is considered a physico-chemical process in which particles attach to air bubbles, depending on their hydrophobicity as well as other factors, and are carried to the surface to form a froth layer. Reagents are used to stabilize bubbles and the froth layer (Pugh, 1996). However, particles, which are carried by the bubbles or entrained, significantly contribute to the stability of the froth phase (Ata et al., 2003; Zanin et al., 2009; Bournival et al., 2015a). Their relevance in mineral processing has led to a number of fundamental studies on the effect of particles and their properties on the process of froth flotation.Flotation systems are particularly difficult to characterize due to the broad range of properties of particles (e.g. size, liberation, hydrophobicity, etc.) and inconsistent operational conditions (e.g. changes in water quality, reagent addition, etc.). Several studies have made the use of well characterized particles in laboratory conditions. Such studies allowed the finding of an optimal contact angle for the stabilization of the froth phase (Johansson and Pugh, 1992; Ata et al., 2002). Froths have a large number of bubbles so that individual interactions are not observed. The study of two bubbles allows to determine the stability of the bubbles, with particles, and to some extend the stability of the bubble-particle aggregate (Gourram-Badri et al., 1997; Bournival et al., 2015b). The removing of particles between two bubbles may also be studied from a Scheludko cell (Johansson and Pugh, 1992) or by observing a bubble with a flat interface (Sethumadhavan et al., 2002). However, these systems provide limited information on the arrangement of the particles."

Jan 1, 2018

By Ivan Bonchev, Elisaveta Djurova, Evgeni Visariev, Viktor Stoilov

"Two types of slag cooling is used world wide - cooling in ladles and cooling in pits. The flotation comparison of the type cooling regimes was done at Aurubis Bulgaria. In Copper smelter Aurubis Bulgaria (Pirdop), the residual copper in the slags from Flash furnace and Converters is recovered by flotation. The slag flotation plant processes blend of three parts FSF and one part converter slag. The slag processing comprises: pit cooling, crushing, two stages grinding (autogenous and ball) and flotation. The copper content in flotation concentrate is over 20 % and in flotation tail is under 0.5 %. In order to improve the copper recovery, different cooling rate of the liquid slags should be achieved. Three cooling experiments with flash smelting furnace (FSF) slag have been done: two of them in pits with different volume and one cooling experiment in metallic ladle. The ambient air temperature during the cooling tests was from -4 to +4 OC. Laboratory flotation tests in open cycle were done with an aim to compare the slags behaviors cooled at different conditions. In this paper the effect of different cooling on the flotation process will be presented. The copper recovery and distribution by sizes in the tails, copper content in the rougher concentrate, and the concentrate yield are discussed."

Jan 1, 2014

By Mario Gerards, Sergej Podkow, Marco Steinberg

"The JONES® WHIMS technology is based on the magnetic separation process and is widely used for the recovery of magnetically susceptible iron ore particles. The conventional machine design is well-known within the iron ore beneficiation industry for more than 50 years and recognized to be highly reliable, robust and extremely compact with the advantages of high capacity and selectivity. In 1981 Rana Gruber AS, Norway bought 14 JONES® WHIMS DP 317 separators when the magnetic separation plant was built and erected. Today, 11 of these old machines are still operating profitably and efficiently. The former supplier was the coal and minerals division of Klöckner-Humboldt-Deutz (KHD) which is today MBE Coal & Minerals Technology GmbH (MBE). This paper outlines a detailed description of the project of revamping the above mentioned old machines and describes the challenge of incorporating enhanced and newly developed technology into an existing processing plant. Further it gives an overview of the recent developments on the design of the JONES® WHIMS. In order to meet modern product requirements and to increase and secure plant productivity, in 2012 Rana Gruber AS settled a contract covering two new designed JONES® WHIMS DP 317 HFR separators to be implemented into the existing building and the upgrading of all 11 older JONES® WHIMS under the use of as many refurbished items as possible. The two new machines were fully developed by the product specialists of the supplier in cooperation with the operator Rana Gruber AS, thereby taking advantage of their great experience. The design of the new machine is based on the conventional design, i.e. the general operating mode as well as the overall dimensions are identical. Finally this paper gives an overview about the erection and commission phase of the two new machines and gives a detailed comparison between conventional and enhanced WHIMS technology."

Jan 1, 2014

By T. N. Matveeva, L. B. Lantsova, N. K. Gromova

"Multimetal gold-antimony ores are complexed processing products, since they are characterized by veindisseminatedsulfide mineralization with fine-dispersed submicroscopic gold, low content and uneven distribution ofAu, which is concentrated together with iron sulfides (pyrite, arsenopyrite, pyrrhotite). Such ores are classified asrefractory ones and characterized by low gold recovery rates during cyanation. A particular feature of gold-antimonydeposits is the presence of antimony in industrial concentrations therein, along with gold that significantly increasesthe value of these deposits. The main antimony mineral is antimony sulfide - antimonite (stibnite). Gold-antimonyores undergo flotation concentration with producing collective gold-containing concentrates or gold sulfide andantimony concentrates. The purpose of the work is an experimental study of the flotation separation mechanism ofsulfide minerals of copper, antimony and arsenic using tannin-containing modifiers during processing of multimetalgold-bearing ores. During the research it was established that for the selective separation of antimony and arsenicsulfide minerals into concentrates of different kinds, it is possible to use vegetable reagents capable to be selectivelyadsorbed on the arsenopyrite surface. Using the laser KEYENCE VK-9700 and electronic LEO-1420 VP INCA-350microscopy methods, it has been established that the film of a vegetable modifier was not washed off with water andfixed firmly enough on the surface of the polished sections of arsenopyrite. In the X-ray spectrum there are C and Obands related to the reagent structure. The vegetative reagent is fixed both on the pre-adsorbed phase of the collectorand on the areas free from the collector. On the polished sections of antimonite before and after a contact with thetannin solution, only partial adsorbed tannin phases are detected, which disappear as a result of subsequent washingwith water.The reported study was funded by RFBR according to the research project ? 16-05-00646 ?."

Jan 1, 2018

By Seher Ata

This paper is concerned with the coalescence behaviour of two bubbles in dilute solutions of cetyltrimethylammonium bromide, methyl isobutyl carbonil and triton x-100. Two bubbles were produced at the tips of adjacent capillaries and the time elapsed between the first contact of the bubbles and film rupture was determined by means of a high speed camera. It was found that the amount of surfactant required to stabilise the bubbles increased in order of CTAB>TX-100>MIBC. The probability of coalescence decreased sharply with increasing surfactant concentration in CTAB and TX-100 solutions while with MIBC each bubble pairs resulted in coalescence, giving hundred per-cent coalescence probability.

Jan 1, 2014

By M. Kanuchová, J. Briancin, M. Achimovicová

"Faculty of Mining, Ecology, Process Control and Geotechnology, Technical University, Košice, Slovakia An industrial eccentric vibratory mill was used for direct and short-time mechanochemical reduction of ilmenite concentrate (FeTiO3) and anatase (TiO2) with magnesium metal powder in order to reduce Fe and Ti resp. and hereby to convert them to the more soluble phases suitable for further hydrometallurgical processing. X-ray diffraction analysis of FeTiO3 after 60 min of milling with Mg confirmed the presence of Fe0 and Mg2TiO4 phases and for TiO2 after 180 min of milling the new TiO and MgO phases have appeared. X-ray photoelectron spectroscopy has detected Fe0 (metal) and Mg2+ species which are corresponding to the product of FeTiO3 mechanochemical reduction. The product of TiO2 mechanochemical reduction has revealed XPS spectral lines corresponding to Ti2+, Ti4+ and Mg2+ species on its surface. Morphology of mechanochemically reduced samples was studied by scanning electron microscopy analysis. Subsequent leaching of mechanochemically reduced FeTiO3 and TiO2 was performed in dilute HCl and H2SO4 at 80oC and compared with mechanically activated samples. The recovery of Ti has reached 100% for FeTiO3 and 79% for TiO2 after 60 min of leaching. Based on this study the flowsheet for possible processing of natural refractory titanium ores patented by author was adapted and documented. INTRODUCTION Ilmenite (FeTiO3), along with rutile (TiO2) represents the most important titanium resource necessary for titanium industry, for production of titanium metal, alloys and pigment grade TiO2 which are becoming more important and versatile for various industries such as an aircraft and aerospace, navy, chemical, automotive, medical and offshore wind industries, for machine and plant engineering and architecture as well, mainly due to high corrosion resistance. Pigment grade TiO2 is utilizing in pigment, plastic, glass, paper and rubber industries (Zhang, 2011). There are obvious research efforts for development of the potential alternatives to the expensive thermo-chemical commercial processes of titanium raw materials processing. Zhang (2011) has summarized conventional thermo- a electrochemical processes which involved a combination of pyrometallurgical, hydrometallurgical and electrometallurgical technologies and highlighted the improved hydrometallurgical routes promising for commercial application in the future. Such improvement could also be mechanical activation of FeTiO3, TiO2 by high-energy milling which causes their structural disordering, the changes of physical and chemical properties, consequently and has a positive effect on the dissolution kinetics (Achimovicová et al., 2014a, 2017, Baláž, 2008). The various types of mills such as a planetary ball mill, a vertical ball mill, a drum mill, an attritor were used for mechanical activation of FeTiO3 as a pretreatment process for subsequent leaching (Achimovicová et al., 2014)."

Jan 1, 2018

By Xu Wang, Bang Chen, Xiujian Luo, Wei Tang, Xiao’ou Xia, Fangming Liu

"The inertia cone crusher has lots of advantages, such as big crushing ratio, fine particle size, material layer crushing, good passing tramp iron performance and stable technical index, realized open crushing circuit and simplified crushing flowsheet. The crusher was input to China’s Beijing General Research Institute of Mining and Metallurgy (BGRIMM) from Russia’s Mekhanobr-Tekhnika Research & Engineering Corporation at the beginning of the 1990s. This paper introduces that after years of absorption and innovation how Chinese researchers optimized and creatively designed about transmission mechanism, bracing structure, kinetic parameters, lubrication system, dust sealing system, damping system and hydraulic control system etc on the basis of keeping its advanced theory and unique structure, therefore the crusher’s stability was raised and the usage cost was reduced greatly. Accordingly the inertia cone crusher in China has been widely used in many fields, such as mineral resources and the recycling of metallurgical slag. The achievement in cooperation was fully affirmed by governments of Russia and China, and cooperation of science and technology in the mining and metallurgy industry between Russia and China is promoted greatly. INTRODUCTION From the early 1950s, the former Mekhanobr Institite(now Mechanobr-Tekhnika Research & Engineering Corporation) devoted itself to the research of inertial cone crusher and put it into industrial application in the late 1980s. Inertial cone crusher is like a maverick flower in the field of crusher. With its excellent performance and excellent application effect, it shocks the world and is destined to shine with a bright future. In the early 1990s, the chief leaders of the Beijing General Research Institute of Mining and Metallurgy (BGRIMM), Academician Sun Chuan-yao and Professor Zheng Baochen, captured the extraordinary performance and strong vitality of inertial cone crusher with keen eyes. So the two big institutes started the cooperation to introduce inertial cone crusher to China. Since then, Inertia cone crusher has been able to flourish in China and have achieved impressive results with two institutes’ continuous effort."

Jan 1, 2018

By S. M. Javad Koleini

The aim of this research is to extract zinc from complex lead and zinc ore containing carbo- silicate lead and zinc minerals using sulphuric acid. Samples, taken from Dareh Zanjireh mine located in central of Iran, were subjected to leaching tests after calcination process. Experiments were planed according to the Taguchi statistical method. The calcinated samples contain 13.98% zinc and the constituting minerals being dolomite and zincate. Various parameters such as speed of mixing, temperature, time, solid to liquid ratio and pH were studied. A solid to liquid ratio of 1:6 gr/mL at 60°C and 800 rpm speed of mixing for 30 minutes resulted in a product with 85.96% zinc recoveries.

Jan 1, 2014

By Neill Bartie, Jacques Eksteen, Sharif Jahanshahi, Shouyi Sun

The gradual increase in Cr2O3 levels of UG-2 ores has become a matter of concern for platinum producers in South Africa due to the formation of chromite spinels in melters. The effect of bulk FeOx/MgO ratio, Cr2O3, temperature and oxygen partial pressure on phase stability and composition in the system FeOx-MgOSiO2- Cr2O3-Al2O3-CaO has been studied between 1400°C and 1600°C using the drop-quench technique. An increase in temperature was found to result in a decrease in [Fe/Cr]spinel. An increase in bulk FeOx/MgO caused Mg, Al and Cr in spinel to decrease, forming more magnetite relative to other spinels. [Fe]spinel decreased and [Cr]glass increased with a decrease in oxygen partial pressure.

Jan 1, 2003

By Gabriel Barrios, Juan Pérez-Prim, Marcelo Tavares

"The application of High Pressure grinding Rolls (HPGR) has been growing in the mining industry for the last 10 to 15 years. The major benefits generally supporting this trend are better energy efficiency, improved grinding capacity, less sensitivity to ore grindability variations and higher metal recovery in downstream processes such as heap leaching and flotation. The HPGR machine comprises a pair of counter-rotating rolls mounted in a sturdy frame. One roll is fixed in the frame, while the other is allowed to float on rails and is positioned using pneumohydraulic springs. The feed material is introduced in the gap between the rolls and is crushed by the mechanism of interparticle breakage. Comminution performance is largely determined by the pressure exerted on the bed of particles by the floating roll hydraulic system. The operating bed pressure depends on the hydraulic system start-up parameters and the loading response of the feed material. The work describes how the coupling of the multi-body dynamic simulation with Discrete Element Method in which particle breakage is described using the particle replacement method, can be effectively used to predict the performance of the HPGR. The model considers important variables as the HPGR rolls geometry and design, the hydraulic spring system start-up parameters and the material loading response, to describe operational key outputs as material throughput, operating gap and roller pressure distribution. The preliminary version of the model has been used to predict the effect of material properties on the operating gap and the load distribution on the surface of the rolls, demonstrating that it can describe qualitatively the HPGR operation, indicating that the model will be a power full tool for the simulation and selection of industrial HPGR units."

Jan 1, 2014

By G. Dodbiba, T. Fujita, M. Kawata, S. Yamasaki, K. Mitsuhashi, J. Ponou, Y. Iwazaki, T. Atarashi

"The grade of copper ore and concentrate is recently decreasing and it will continues decrease further in the future. The effective liberation treatment for low grade copper ore and the removal of arsenic from copper concentrate is becoming even more important. In this work, the magnetic separation of copper concentrate by heat treatment and the flotation of low grade copper ore by microwave irradiation was studied. The heat treatment of copper minerals in the air atmosphere, the magnetization of most copper minerals increases and especially the magnetization of chalcopyrite shows the largest magnetization, after being heated at 500 oC. The wet HGMS of copper concentrate has been studied and the results have then been compared with the ones when calcined concentrate was used instead. The microwave treatment before ball milling increased the degree of liberation up to 100%, especially when compared with the case when only ball mill was applied to the as-received ore. The flotation of ground copper ore after microwave irradiation showed that the grade copper minerals such as chalcosite and bornite in froth part is much larger than that of tailing part.INTRODUCTION The copper has been used many kind of technological fields and will be more important for the future technology. The global copper production from mine is predicted as shown in Figure 1 (Northey, S. 2014). The copper production peak will be appeared in 2030 and the demand peaks in 2040. In the future the recycling of stocked copper and copper alloy will be necessary to satisfy the demand (Yoshimura, A. 2018). Changes in the grade of copper in copper concentrate, exported from several countries are shown in Figure 2. The copper grade in copper concentrate after mineral processing is gradually decreases every year and it is less than 30% nowadays. On the other hand, the copper ore grade change and prediction are shown in Figure 3. The grade of copper ore is also decreasing to less than 1% in 2010 (Northey, S. 2014). In the future the copper grade gradually decreases, reaching to less than 0.5% in 2080 and the energy to produce the copper metal will increase. The effective liberation treatment for low grade copper ore and the removal of arsenic from copper minerals become more important, nowadays. The microwave irradiation of copper ore for the liberation, energy etc. has been reported by several researchers (for example, Batchelor, A.R. 2017). The magnetization change of copper ore by heating has been reported to remove the arsenic (Sawada, M 2015). In this report, the magnetic separation of copper concentrate by heat treatment and the flotation of copper concentrate by microwave irradiation are discussed after the characteristics of secondary copper minerals are investigated by these treatments."

Jan 1, 2018

By E. A. Bekchurina, Yu. P. Morozov

"This paper presents the results of a study of the concentration of flotation froths in tapered chutes. The tests were conducted on lab and full-scale plants, and the results obtained were mathematically processed. The kinetics of monophase recovery from a stationary flotation froth, hydrodynamics of froth flows traveling in a tapered chute were investigated. The effect was studied of the mass fraction of the valuable component in the chute feed, yield of the chute’s overflow, and chute design on the concentration performance. Processing of the collected data revealed the general laws of the process and allowed to develop a technique for modeling concentration of the flotation froths of sulphide copper ore in a tapered chute to predict the performance without testing. It was found that concentration in tapered chutes allows to obtain products that are comparable in quality with froths after one or several cleaner flotation stages.INTRODUCTIONThe present production expansion rates require continuous improvement in the grade of flotation concentrates, while the grade of the mineral feed is constantly deteriorating. This leads to a significant complication of flotation flowcharts. Flowcharts become multi-staged with multiple cleaner flotations, negatively affecting the production costs.In recent years, researchers are paying close attention to the processes occurring in the froth layer in the flotation cells. Improving the concentrate grade is facilitated by secondary concentration of minerals in the froth layer, which consists in fixing the hydrophobic particles released as a result of the coalescence of the bubbles of the upper layer when moving downward at the liquid-gas interface of the froth layer. In this case, the released hydrophilic particles, trapped in the froth layer as a result of mechanical removal, migrate from the froth together with the liquid phase."

Jan 1, 2018

By Y. Y. Zhou

This paper introduces the application of CRIMM high-gradient magnetic separator in refinement of feldspar powders as well as the supporting technical outfits needed by the refining process with the high-gradient magnetic separator as main equipment. It could reduce the content of Fe2O3 to 0.03% with a deferrization rate of 85.88% from the feldspar raw ore containing 0.17% Fe2O3by using the above refining technology, producing an ultrapure feldspar product.

Jan 1, 2014

By X. O. Xia

This paper introduces a kind of flotation machine for nonferrous metal, ferrous metal and non-metal minerals. With the application and development of flotation machine, researching the designment of master parts, including tank, impeller, stator, false bottom. Through the commercial run to validate the correctness of designment, achieving satisfied technical and economic target and supplying a kind of efficient and reliable flotation machine.

Jan 1, 2014

By A. M. Muhamedilova, S. M. Narbekova, L. V. Semushkina, D. K. Turysbekov, N. K. Tussupbayev

The research and development of new, more selective collectors in order to improve flotation efficiency represent one of the main priorities in the development of innovative technologies pertaining to flotation separation of various substances and minerals. The use of collectors’ mixtures is considered as the universal instrument for ensuring necessary proportion of chemically and physically sorbed collecting reagents in every individual case. Currently hard-dressed, refractory ores and man-made raw materials, which are characterized by low content of valuable components, fine dissemination of mineral assemblages and similar technological properties of constituent minerals, are widely involved in the recycling processes. The possibility of processing tailings, which are left after flotation beneficiation, has been considered in the case study of tailings of the Zhezkazgan beneficiation plant and the Tishinsk copper ore deposit with utilization of the modified multifunctional flotation reagents. Modified poly-functional collector is the mixture of composite Aerofloat, TC-1000 and butyl xanthate. Reactants ratio is 1:1:3. The advantage of the suggested flotation reagents is that they are composed of two polar groups and have a long hydrocarbon radical. This structure, being in the water during flotation process, plays a dual role: first, as a collector adsorbing on the mineral surface it produces metal complexes with polar groups in the form of bridges; second, apolar radicals flocculate valuable slimed components, thereby intensifying flotation process. It has been shown that flotation of Zhezkazgan tailings with utilization of the lesser modified reagent amount compared to butyl xanthate has enabled to produce crude copper concentrate with 13.0 % copper grade and 80.22 %recovery. Compared to the baseline technology, copper content of crude concentrate has been increased by 5.1 % and the recovery by 31.4 %. It is shown that tailings flotation of the Tishinsky field by applying modified collector allows for increase of the of useful components extraction in a collective concentrate with: copper 9.63 %, lead for 8.41%, zinc 9.2 %, iron 2.73 %, gold 3.57 %.

Jan 1, 2018

By Jan J. Cilliers, Nicolas Barbian, Esther Ventura-Medina

"Froth structure and stability are known to play an important role in determining flotation recovery and selectivity. An industrial sampling campaign was performed to develop a clearer understanding of the effect of flotation variables on froth stability and the role played by the resulting stability on flotation performance.Froth stability was estimated as the fraction of bubbles bursting on the surface of the froth through image analysis and the solids loading on the bubbles at the top surface. It was generally found that high air flowrates resulted in a drop of froth stability showed by a drop in the fraction of air overflowing and a decrease in the solids loading and simultaneously produced low copper recoveries and low concentrate grades. Deep froths only allowed a small fraction of air to overflow and consequently produced low recoveries. An increase from a standard to high frother dosage did not result in a larger fraction of air overflowing, hence producing low recoveries. Likewise, low frother addition only allows low recoveries because the resulting unstable froth cannot support itself. Low aeration was found to be preferential as it allowed high particle loading, therefore high bubble stabilisation, and low gangue entrainment, resulting in the highest flotation performance.Additional laboratory tests were performed to introduce a new stability parameter and to give a clearer understanding of the effect of flotation variables on froth stability. The results confirmed some of the observations made on the plant."

Jan 1, 2003

By L. Burdukova

"In flotation, depressants are used to reduce the amount of gangue that reports to the concentrate and hence increase the selectivity of the flotation process. At the University of Cape Town extensive batch flotation tests are carried out to evaluate industrial depressants and standard procedures have been developed over the years.This study was conducted in order to develop an improved method for comparing depressants using machine vision as an aid. The modified method of batch flotation involved a test with prolonged intervals between scraping to allow more time for the froth to build up and mature.This method of testing showed increased differences between the flotation performance obtained as represented by grade recovery curves for carboxymethyl cellulose and guar depressants when compared to the standard method of testing with shorter scraping intervals. The improvement was attributed to reduced entrainment resulting from longer drainage time in the froth and therefore yielded a better test for comparing depressants on the basis of true gangue flotation with minimized entrainment. As expected, the sulphide recoveries were unaffected by the change in method. The machine vision system also added to the information obtained during these tests by recording bubble size trends throughout the tests which were later analyzed and related to the amount of flotable gangue in the froth. Modifications are recommended to improve the usefulness of machine vision in batch flotation."

Jan 1, 2003

By S. Narra

Converting biomass into valuable fuel requires various preprocessing of the raw materials. Biomass densification is one of the conversion processes for its utilization. The aim of densification is to produce biomass pellets, which can withstand regular handling stresses and exhibit high densities with uniform size and shape. Physical properties, such as the particle size distribution after comminution is of highest importance for the binding mechanisms in the pelletisation process. Durability and strength of the pellets play an important role indicating the ability to withstand handling stresses. Particle size distributions of the cereal straws (Rye and Wheat) after specific comminution and liberation processes have been carried out with the help of three different image analysis (Microscope, Camsizer and Fibreshape). The durability of the pellets have been investigated as specified in the standards (ASAE standard S269.4) with a quadratic crate and the strength of the pellets with compression and tension testing machine (Zwick Roell type: ZMART.PRO). The particles size results showed differences in both length and width after different comminution processing. An exact comparison between the particle size analyses with the three different image analyses was not possible. The particle size distribution and the different comminution processes displayed influences on the durability and strength of the produced pellets. The particle size distribution displayed approximately 40 % of fines and 60 % of fibers. The particle size distribution displayed a direct relation to the durability of the pellets. Further durability and strength of the pellets displayed a good correlation.

Sep 1, 2012