Search Documents

By X. Y. Liu

A culture-independent approach based on 16S rRNA gene clone library was used to analyze the bacterial community change both associated to the solids and in the liquid phase during pyrite bioleaching process. Phylogenetic analyses of 16S rRNA fragments revealed that the retrieved se-quences mainly related to genus Leptospirillum, genus Sulfobacillus and genus Acidithiobacillus. During the bioleaching process, genus Leptospirillum trends to grow associated to the solids while major of genus Sulfobacillus were in the liquid fase, only accounting little portion in the solids. Genus Acidithiobacillus can grow both on the solids and in the liquid phase, but accounting high portion on the solids.

Jan 1, 2014

By B. P. von der Heyden, P. Neethling, M. Tadieb, L. Babedi

The effects of trace element substitutions in sphalerite mineral structure on optimised floatation response have, as yet, not been fully constrained or fully understood. To further this important field of study, this contribution focusses specifically on mineral and surface chemistry, and electro-chemistry of Cd- and Co- substituted synthetic sphalerites using Raman spectroscopy and Zeta potential experimentation. Raman spectroscopy illustrates that the presence of these impurities results in the introduction of a new mode, the relative intensity of which can be correlated (Cd r2=0.95 and Co r2= 0.99) to the dopant concentration. Comparison to X-ray Diffraction results measuring the unit cell parameter further shows that this relative intensity (Cd r2=0.81 and Co r2= 0.99) may provide insights into the degree of lattice strain within the mineral structure. The zeta potential distribution of an un-activated Cd-sphalerite show no detrimental effect as function of Cd content. Although the iso-electric point shifted from 2.45 at 1 wt.% Cd to 2.69 at 3.68 wt.% Cd, the zeta potential remained negative at alkaline media. Conversely, cobalt at low concentration of 0.36 wt.% had a detrimental effect on the surface charge, resulting to a close to neutral zeta potential at different pH. The adsorption of Cu ions on the surface of Co-bearing sphalerite conditioned in an alkaline media slightly increases the zeta potential of Co-sphalerite. While the Cd-bearing sphalerite decrease in negative zeta potential at >1 wt.% Cd indicating a complete exchange between Cu and Zn. The results presented herein illustrate that, based on the chemical nature of the substituting metal; sphalerite will exhibit multiple response to flotation reagents. Maximum recovery of zinc can thus only be achieved through multidisciplinary study and fundamental understanding of the effects of cation substitution on mineral structure and surface chemistry, the latter necessarily affecting the floatation response.

Jan 1, 2018

By A. K. Majumder

In an effort to test the extent to which fundamental fluid mechanics can provide a prediction of particle separation, a study on a simple parallel-sided sluice has been carried out using glass bead and ilmenite mixtures at various particle concentrations and flow rates. Great care was taken to devise a flow splitter at the end of the sluice that permitted accurate measurement of the fluid flow profile and collection of slurry samples, allowing evaluation of the particle species concentration profiles. The actual particle separation taking place was compared to predictions made by first describing the fluid flow by a modified ?law of the wall? model. The hydrostatic pressure variation in the flow was taken into account and the eddy viscosity was calculated from a mixing length expression incorporating Van Driest?s damping function. Using an average density and viscosity provides an explicit expression for the velocity gradient that can be numerically integrated for the flow profile. The particle concentration distributions were then modelled with Hunt?s sediment transport model assuming the particle eddy diffusion coefficient to be the same as that for the water. Hindered settling velocities of the particles were calculated using Brauer and Thiele?s formula, which takes the particle size and density distributions and solids volumetric concentration into account. The resulting predictions of particle separation are shown to be a strong function of the settling velocities of the particles used. Keywords: flowing film concentrators, fluid velocity

Sep 1, 2012

By M. Blagojev, R. Tomanec

"Studies reported in this paper used polymetallic Pb-Zn-Sb-As-(Ag, Au) ore from Dražnja, Kosovo. The ore is comparatively rich in Zn (6.56%) and Pb (2.87%), but with high rates of Sb and As. Conventional lead and zinc concentration by flotation produced galena and sphalerite rich concentrate with high recovery, but with excessive As and Sb. After chemical analyses, which could not detect the reason for the excessive elements, ore minerals were identified under the ore microscope, their texture characterized, and degree of liberation of useful minerals was assessed. Microscopy of the mineral concentrates revealed complex intergrowths of galena and marmatite minerals mostly with sulphosalt minerals (boulangerite, jamesonite and bournonite) and also with arsenopyrite mainly responsible for the unsatisfactory quality of the concentrate. These complex sulphosalts, among other things have similar behaviour during the flotation concentration, and in spite of their interlocking with galena, therefore inadequate liberation, sulphosalts remain in the lead concentrate. Microscopic analyses indicated that a better galena concentration product is possible with a higher rate of mineral liberation, and then by selective floc flotation of some sulphosalt minerals. Purpose of this work was to show that only chemical analysis is not sufficient, according to that we solved the problem by precise mineral identification and time consuming mineral liberation measurements. INTRODUCTION The polymetallic Pb-Zn-Sb-As-(Ag, Au) ore body of Dražnja, Kosovo, fairly rich in Zn (6.56%) and Pb (2.87%) was repeatedly explored and once even worked. Mineralization at Draznja was primarily represented by sphalerite, galenite and marcasite/pirite. Some sections comprise massive sulphides, and others are lower grade zones of semi-massive sphalerite/galena or marcasite/pyrite dominant sulphides. The ore body II was formed in the southern gallery in the structure Çukë – Lajthishtë (with content of 3.16% Pb and 7.31% Zn). Pb-Zn ore with increased content of As, Sb sulphosalts is not rare phenomenon in the world. While previously treated as unprofitable, economical uninteresting ore, today with development processing and new reagents (organic, ecologic), are the topic of scientific papers. The examination of Pb-Zn ore with high content of sulphosalts we find in deposits as: The hydrothermal vein deposit of Harja in the Baia Mare area, contain a wide variety of sulphosalts [Cook, N. & Damian, G., 1997]; also the deposits Fankou Mine in Guangdong Province and the Dachang Mine in Guangxi Province, where the flotation concentration of galena and jamesonite takes place [Runqing Liu et al. 2015], [Zhang Ting, Qin Wen-Qing, 2015];. On a samples from Tibet in China flotation separation test of galena and jamesonite was conducted [Sun Wei, Han Haisheng, Tao Hongbiao, Liu Runqing, 2015]. According to history of investigation, the mineralized area of Dražnja has a long history of exploration and possible exploitation activities [Slowey, Galen, 2009]. Recent workings were carried out in three stages through the 20th century."

Jan 1, 2018

By B. Csoke

As opposed to large household appliances, in the processing of which dissambling has an important role, this possibility is pushed into the background as the size decreases. The practicable solution is physical liberation of the used small electronic household devices (by comminution) and separation of the liberated components according to their physical properties. In the first phase of the experimental work the structural/material composition of the typical products (mixer, kitchen robot, hair dryer, coffee machine, iron, bread toaster, vacuum cleaner, oil fryer) was determined. In the second phase a physical liberability test for each appliance using a rotary shear/shredder for crushing and a hammer shredder for milling was carried out. In the third phase the experimental separability tests using an air classifier and a shaking air table, as well as an eddy-current and an electrostatic separator were performed. In the present paper the results obtained using the air classifier and the electrostatic separator, are reported. To follow the life of a grain a new methodological procedure was elaborated. The particle size fractions after comminution were sorted into material fractions (copper, aluminium, plastics, etc.), then separated, and finally the recovery of the material components in the products were determined. Furthermore, the joint separability was investigated from two points of view: 1) for grain fractions and 2) for each waste appliance. According to the tests carried out so far, it was established that it is reasonable to form appliance groups by selection (e.g. mixer, iron, bread toaster and similar appliances form the first group, while the sandwich oven,

Jan 1, 2014

By O. Guven, I. Karaagaçlioglu, O. Ozdemir, M. Çelik

In this study, the effect of morphological properties such as shape factors and roughness of the glass beads on their flotation efficiency were determined using image analysis and profilometer methods. There is a considerable correlation between the shape factors, surface roughness and flotation behavior of the glass sample. These results indicate that as the particle shape is away from roundness and smoothness, it acquires more hydrophobicity.

Jan 1, 2014

By J. A. Venter

Mineralogical studies indicate the Pt-Pd-Bi-Te class to react poorly on the flotation stimuli and indications are that these minerals are slow floaters. However, recent studies performed on a number of minerals from this class indicated strong interactions with potassium ethyl xanthate resulting in the formation of dixanthogen (only one of several xanthate species). The poor flotation response is not a result of poor interaction of xanthate with the surface. It is proposed that the oxidation products of sulfides in the process water interact with the PGM surface. To test this, the effect of thiosulfate (an important oxidation product of sulfides) was investigated by employing electrochemical measurements and FTIR spectroscopy. The electrochemical investigations indicate no strong effect of thiosulfate on the interaction of xanthate with the minerals surface as well as the reduction of oxygenthiosulfate is likely not responsible for the poor flotation response of these minerals in industrial plants.

Jan 1, 2014

By S. N. Shahcheraghi

Bioleaching method makes use of bacteria in solving metallic sulphides, so that these bacteria tend to convert insoluble metal sulphides into soluble sulphates. Since the kinetics description of this process is inevitable for better interpretation of relation between metabolism and growth of live organisms, as well as optimization of metals extraction processes, in this paper, this description is represented and designed in mathematic (kinetics) model for copper sulphide minerals based on Monod kinetics model. According to this model, special growth rate of bacteria (?) is a hyperbola function of restrictive substrate concentration (S). By Solving and developing of Monod kinetics model, a comprehensive kinetics model for bioleaching of copper sulphide minerals results. The designed is also applicable for other metal sulphides.

Sep 1, 2012

By Q. Huo

The alumina production might not continue when the sulfur content of bauxite was too high. In order to bring down the sulfur content in bauxite, we studied on the bauxite desulfurization by bacteria screened from the acid mine drainage at mines of high sulfur content. The screened bacteria were domesticated by the high sulfur content bauxite. The experiments of bauxite desulfurization were carried out under the conditions of 5% pulp density, temperature of 30?, rotate speed of 120rpm. Bacterial desulfurization for 30 days, the sulfur content of the bauxite was reduced from 5.73% to 1.55% and the desulfurization percent was 72.9%. The recovery percent of alumina was 94.3%. The study showed that it was feasible to bring down the sulfur content of bauxite by bioleaching and this technique might make full use of the low grade bauxite.

Jan 1, 2014

By S. A. Kondratyev

"The present research work aims at disclosing the dependence of flotation concentrate recovery and its grade on the physically adsorbed collecting reagent properties, viz., surface pressure in the reagent film at gas-liquid interface, velocity of reagent species spreading over the said interface, relation between interaction energies of collector molecules within a film and with water dipoles.When using a single collecting reagent it is possible to improve the flotation concentrate grade in two ways, namely, by reducing collector consumption rate or using a weaker reagent. According to the proposed mechanism, a decrease in the physically sorbed species of the collector leads to a decrease in the rate of removal of the kinetic restriction of a flotation contact formation. As a result, the recovery of the useful component is reduced and the content of valuable components in the flotation concentrate is increased. The relationship between the spreading velocity of physically sorbed species at the gas-liquid interface and the recovery and quality of the flotation concentrate has been experimentally proved. Reduction in collector consumption lowered the valuable component recovery at a higher grade of the concentrate.The reasons were established for a rise of valuable content in the flotation concentrate if a weaker collector was used. It is justified that the use of a weaker collecting reagent with a shorter hydrocarbon fragment declines physically sorbed species of collector. The spreading velocity of collector derivatives at gas-liquid interface tends to lower along with less participation physically sorbed species of collector in formation of a flotation aggregate. The spreading velocity is determined for products of interaction between butyl-and ethyl-xanthates and lead nitrate at gas-liquid interface. It is found that the spreading velocity of butyl-xanthate derivatives is higher than that of ethylxanthate derivatives.The research work gets insight into the nature of relation between useful component content in the flotation concentrate and the useful component recovery. It is pointed out that adjusting the collecting activity of a collector makes it possible to influence a useful component content in the froth product thus gaining a compromise between wanted grade and recovery parameters."

Jan 1, 2018

By B. Csoke

In a first stage of our investigations material properties of fly ash (three acidic and one alkaline type originating from combustion of various age coal) obtained from four various dumps have been characterized. In a next step systematic mechanical activation experiments??grinding??and measurements have been performed with various ashes to establish relations between grinding fineness (specific surface area), specific work input demand of grinding and activity. In a third phase utilization of a mixture of mechanically activated fly ash and lime for producing an independent binding composition has been assessed involving determination of interrelationship(s) between the degree of activation of fly ash, the lime concentration and the resultant strength of the obtained concrete. Finally, pilot size experiments were conducted and a test road section was built to explore possibilities for the production of suitable binding composition from the mixture of fly ash and lime as well as the applicability such mixture for road construction. After summarizing major achievements of the first and second stages of the work (history) the present study deals with the research conducted in stages three and four. Experimental results support the conclusion that the obtained binding material is suitable for construction of road bedding.

Jan 1, 2014

By S. H. Morar

Froth flotation is a physico-chemical separation process that takes place in two phases; pulp and froth phase. It is widely recognised as a complex process, due to the range of interactions present within the system. Of critical importance is the role of the froth phase within the system. The pulp kinetics governs the maximum potential recovery within a flotation cell, while the froth phase governs the selectivity via the froth?s stability. Higher froth stability improves recovery at the expense of grade, and lower froth stability improves selectivity. It is well known that the two major factors affecting froth stability are attached particles and solution chemistry. This paper looks at a flotation bank at different froth depth and frother concentrations. The air recovery to the concentrate is determined at each condition and relates the effect of the operating conditions on froth stability and transport to the amount of solids that are recovered to the froth and concentrate by true flotation. The results presented show that, for a given process objective, which in this case was a consistent mass pull profile, depending on the operating conditions, solids recovery in the pulp is affected by the air rate required to maintain the target mass pull. To a smaller extent, the changes in the pulp composition affect down-stream pulp recovery. The variation in solids recovered into the froth drives the froth stability at the start of the flotation bank, while the frother drives the froth stability at the end of the bank. The performance in between these two extreme conditions arises from an interaction of these two effects. The consequences of these interactions can give rise to counter-intuitive responses that can confound efforts to optimise the performance of the bank.

Jan 1, 2014

By I. N. Gridasov, T. V. Ignatova, E. V. Shelepov

"Mikhailovskoye Deposit is comprised of oxidized ferruginous quartzites among other minerals with the former widely spread across the ore field and mined along with unoxidized ferruginous quartzites. PJSC Mikhailovsky GOK strategic development is aimed at iron ore product output expansion. The most critical item of the strategic development road map is process design for separation and concentration of hematite contained in oxidized ferruginous quartzites mined as the by-product in the open pit. Laboratory and semi-industrial tests run to design cost-effective, reliable and environmentally friendly process for Mikhailovskoye deposit oxide quartzites processing included the following processes: - pilot tests of reverse anionic flotation which produced concentrate with Fe60.1-62.9% total iron content and 66-69%Fe recovery rate; - combined magnetic separation and flotation (Marubeni Company, 1982) including slime removal, reverse anionic and cationic flotation and high gradient magnetic separation resulting in 48.9% yield, Fe55-57.5%, up to Fe60.5% hematite concentration ( Fe64.1% being the best result achieved),76.2% recovery. - magnetic separation and flotation, including separation in low gradient (1400 Oe) and high gradient (up to 17000-18000 Oe) magnetic field. The results of these pilots tests were the following: 57-59%Fe concentrate, 70%Fe recovery (Mekhanobrchermet, MGOK, 1982-1988): - magnetic roasting in pilot plant of TSGOK (Krivoy Rog) which produced 61.1%Fe concentrate with 81.5% recovery. Major disadvantage of the method is high generation of dust equal to 20% of the initial feed. Based on third-party studies flotation of oxidized ferruginous quartzites process embracing best processing methods was designed by Metalloinvest Management Company LLC and PJSC Mikhailovsky GOK engineers. This paper discusses analysis of studies aimed at intensification of separation processes with application of mechanical slurry agitation (MSA), addition of alkali (NaOH) and elutriation of initial feed. The paper also provides a design solution to implement a lab-scale MSA plant. It includes feasibility evaluation of MSA inclusion in flotation of oxidized ferruginous quartzites process to enable higher yield and hematite recovery in resultant concentrate. Outcomes of the discussed work have significant value for prospective engineering of OFQ concentration process."

Jan 1, 2018

By Bruno Michaux, Markus Reuter, Martin Rudolph

"It is relatively well-established in the literature that the flotation of calcium minerals using fatty acids as collector is very sensitive to the process water composition. In particular, hard waters have often been reported to strongly reduce the target mineral recoveries due to the formation of insoluble compounds such as calcium and / or magnesium dioleate, thus reducing the amount of collector available for adsorption onto the mineral surface. In this study, the flotation of a fluorite pre-concentrate was performed with tall oil, an industrial collector essentially containing fatty acids. The tests were performed in a variety of synthetic waters to simulate multiple degrees of water hardness, and to differentiate the role of magnesium and calcium ions on the flotation performance. The flotation tests revealed that, under the studied conditions, a significant difference between flotation in calcium-rich and magnesium-rich waters was observed, suggesting strong ion-specific effects in the system. Specifically, calcium-rich waters slightly improved the fluorite recovery, whereas magnesium-rich waters caused a decrease in recovery by as much as 20%. This paper is focused on the flotation kinetics aspect of the system. This approach highlighted the interesting finding that calcium ions did not simply increase the fluorite recovery, but also significantly increased its flotation kinetics. The magnesium ions, on the other hand, had the exact opposite effect.INTRODUCTIONAs the mining industry is facing an increasing number of issues related to its fresh water consumption, the idea of using alternative water sources for mineral beneficiation is gaining significant momentum. As a result, a proper understanding of the role of water chemistry in flotation is becoming more and more urgent, leading to an increasing number of studies on this topic."

Jan 1, 2018

By Indrajit Paul, Atanu Pal, Kapil Modi, Sanjay Chandra, Chandra Sekhar, Srinivas Dwarapudi

"High alumina content in the Indian iron ore fines (2.5% Al2O3) resulted in poor quality pellets at the recently commissioned 6 MTPA pelletizing plant and a study was under taken to establish suitable pellet chemistry through proper fluxing agents. Limestone fluxed pellets were prepared at varying basicity (0 to 0.8) and pyroxenite fluxed pellets at varying MgO contents (0 to 3%) to study their effect on the metallurgical properties. Fired pellets were tested for their strength, RDI, reducibility and swelling. Microstructural studies, optical and SEM-EDS, were carried out to quantify different phases and their chemistry. Acid pellets exhibited poor quality whereas limestone pellets at 0.8 basicity and pyroxenite pellets at 1.5% MgO exhibited optimum metallurgical quality. Formation of widely distributed silicate melt in limestone pellets and high melting point slag & magnesioferrite in pyroxenite pellets found to improve their quality. However during commercial production of MgO bearing pyroxenite pellets, their room temperature and low temperature properties found to be inferior, but exhibited better high temperature properties, viz. softening-melting behavior. Contrary to this, commercially produced limestone pellets, comprising CaO, exhibited better strength and RDI but showed poor high temperature properties. To yield the benefits of both CaO (for good strength and RDI) and MgO (for low swelling and high softening), a dual flux combination was established by using both limestone and pyroxenite/olivine together that resulted in optimum metallurgical properties. Coke rate at the blast furnaces found to be reduced by 1kg for every1% increase of dual flux pellets in the burden.INTRODUCTION Iron ore agglomerate quality plays a vital role in decreasing the reducing agent consumption and increasing the productivity of blast furnace. In most of the integrated steel works, the burden mix for blast furnace is decided as per the availability of the iron ore agglomerates like sinter and pellets. More attention has been given in recent years to the use of fluxed pellets in blast furnace due to their good strength and improved reducibility, swelling and softening melting characteristics. Generally, quality of pellets is influenced by the nature of ore or concentrate, associated gangue, type and amount of fluxes added and their subsequent treatment to produce pellets. These factors in turn result in the variation of physicochemical properties of the coexisting phases and their distribution during pellet induration. Hence properties of the pellets are largely governed by the form and degree of bonding achieved between ore particles and the stability of these bonding phases during reduction of iron oxides (Panigraphy et al., 1990). It is important to note that conditions and parameters of pelletizing are specific to given ore or concentrate; the present study is undertaken for typical Indian hematite ore fines high in alumina. Except authors earlier work on quality of pellets from Indian iron ore (Dwarapudi et al., 2008, 2010), there is no considerable literature reported on the effect of pellet basicity and MgO content in the basicity range of 0 to 0.8 for Indian hematite ore."

Jan 1, 2018

By H. D. Yu

In this paper, an evaluation about the process mineralogy of the rich iron mine in Mongolia with comprehensive methods is given; this provides foundation of the comprehensive recovery of iron and cobalt in the ore. The research shows that the iron?s grade is 61.23%, Co?s grade is 0.02%, the ore is rich iron ore and its Co content also reaches border mining grade. For the ore, if want get high grade iron concentrate powder, must identify the mineral composition and the occurrence of iron and take into ac-count the recovery of Co content as associated resources. Chemical phase analysis results show that 86.35% of iron exists in magnetite, which means that the theoretical recovery ratio of iron is close to 86%. Minerals spectrum analysis confirmed that the magnetite containing a small amount of Mg, Al, and other impurities, the actual iron minerals to 70.28%, which means that theoretically iron grade iron concentrate only close to 70.28%. Based on the result of iron chemical phase analysis, by investigating the liberation of sulfide minerals and gangue, the recovery index of iron can be forecasted, when grinding fineness is 35%, 45%, 55% and 65% bellow 0.074mm,theoretical content of Fe in iron concentrate separately is 67.71%,67.88%,68.78%,and 69.43%,accordingly the theoretical recovery of Fe is 87.38%,87.05%,86.92% and 86.63%. From the perspective of process mineralogy, the forecast mineral beneficiation indicators show that the ore is easy sorting ore, iron processing operations have higher recovery rate, but wants sorting of high-grade iron ore concentrate still need appropriate grinding fineness. Furthermore, associated element Co, existing mostly in pyrite and pyrrhotite, is valuable in the ore. Pyrite and pyrrhotite have ideal liberation under grinding, so cobalt can be easily enriched in sulfide concentrate.

Jan 1, 2014

By X. M. Yu

A large amount of polluted sludge is produced by a nonferrous metal factory after treating waste water with lime/ferrous salt. The concentration of arsenic in the dried sludge is high to 5.84%, a toxicity test is taken on the sludge according to GB5085.3-2007 and the extraction content is 15.75mg/L, which surpasses the arsenic extraction standard [As]=5mg/L, the sludge is categorized as hazardous waste. If put outside without disposal, it would be very harmful to environments. Here we report an optimum protocol to extract arsenic; S2- alkaline liquor is utilized to treat the arsenic sludge. At 85?, 10L 7% S2- liquor is added into 1kg dried sludge and the resulting mixture is stirred for 120min at 250r/min, then separated by centrifugation and the compressed waste residue dried naturally. The average arsenic content is 1.40mg/L, lower than GB5085.3-2007 Standard and arsenic-free residue is consistent with GB18598-2001 Standard, which can be bury safely. The extracted arsenic is transferred into copper arsensite for use as addictive in copper electrolysis and the waste water can be recycle after calcium is removed.

Jan 1, 2014

By E. V. Leont'eva, V. R. Vafin, A. G. Kladova, N. L. Medyanik, A. P. Ponomarev

"The thermochemical technology for recovery gold, silver from mature flotation tailings of pyrite ores by two-stage sintering with chlorine-ammonium reagents and leaching of bakes with water is developed. The economic effect of the technology implementation is calculated. KEYWORDS Gold and silver recovery, mature flotation tailings, pyrite ores, chlorine-ammonium reagents, leaching INTRODUCTION The relevance of processing the technogenic reserves of ore mining and concentration wastes accumulated over the long operation periods of mineral deposits is beyond doubt. Hundreds of tons of precious and non-ferrous metals that were not recovered during the primary processing are concentrated in the accumulated wastes. For example, tailing storage facilities (TSF) at the mineral processing plants in the Southern Urals region of Russia hold more than one hundred tons of gold and thousands of tons of silver in the mature flotation tailings (MFT) of copper pyrite ores. Secondary processing of technogenic materials is facilitated by the fact that they are preprocessed — ground and compactly deposited on the surface, but complicated by the low (compared to ores) grade, uneven distribution of the valuable minerals, altered and unstable material composition of the mineral feed. This leads to low recovery rates of valuable metals by conventional physicochemical processing methods. It is necessary to develop innovative methods of deep integrated processing of industrial wastes, based on the study of the material composition of specific technogenic mineral resources and based on ensuring the environmental safety of the resulting secondary waste. MATERIALS AND METHODS The object of this study are the MFT of Uchaly Concentrator in the Republic of Bashkortostan, Russia, which processes copper pyrite and copper-zinc ores. According to the data of particle size, chemical, X-ray phase, and optical microscopic analyzes, samples of the MFT are characterized by considerable particle fineness (the fraction of the size class -41 µm is 89-90%), low grade of gold (1.7-2.0 g/t) and silver (18.0-19.5 g/t), comparable grades of iron (23.0-26.8%) and sulfur (28.1-28.7), but different grades of copper (0.12 - 0.73%) and zinc (0.34-1.26%). The most common mineral in the samples is pyrite (50 - 56%), found in intergrowth with grains of other sulfides (0.1-4%) - sphalerite, tennantite, chalcopyrite, covellite. Quartz and aluminosilicates are the dominant rock minerals (21-36%). Based on the results of the phase analysis, it was established that approximately 70% of the gold in the samples is found in a form that is resistant to cyanidation — it is locked in sulfides (52-56%) and quartz and coated by films. Along with sulfides and rock minerals, common gold and silver minerals (chalcogenides, intermetallides, native gold) in the form of submicro- and nano-sized precipitates are also associated with intergrowth of a complex structure. These features of the material composition allow classifying the MFT of the pyrite ores as a mature feed material and emphasize the need for chemical non-cyanide methods to recover gold and silver from the mature minerals and associations they are found in."

Jan 1, 2018

By S. Liu

With the development of global economy, the demand of mineral?s quantity and quality are in-creased, valuable minerals are more and more finer and poorer, and the capacity of concentration plant are more and more high. Using large-scale flotation cells can obviously enhance the capacity of treating the mineral, reduce the cost, and increase the economic benefit and competitive ability for the enterprise. BGRIMM advanced advisable technical scheme with optimally parameter and route for the feature of dynamic in large scale flotation machine, and developed the KYF Large Scale Flotation Cells, which have used more than 400. The paper advanced the history, the design principle, the operating principle, the structure feature and the application of KYF flotation ma-chine.

Jan 1, 2014

By Z. F. Dai

The Thompson Nickel Belt, located in Northern Manitoba, Canada, contains more than 400 million tonnes of ultramafic low-grade nickel mineralization in 9 deposits. One of these, the Pipe deposit, was mined between 1971 and 1983 producing a Ni concentrate of 9% to 11% grade at 73% recovery. The operation was terminated because the poor recovery, low Ni grade and high MgO con-tent of the concentrate made processing this ore uneconomical at the metal prices prevailing at that time. Vale Inco is now re-evaluating these deposits with the intent of providing a new source of concentrate for its Thompson integrated processing facility. It is known that serpentine slimes coating on the sulphide surfaces are responsible for the poor metallurgy. Various desliming methods were tested including settling, elutriating, tabling and hydrocycloning. Hydrocycloning has proven to be the most effective means of desliming. With a feed assaying 0.70% Ni and 33% MgO, a rougher flotation concentrate assaying 22.7% Ni and 4.8% MgO was produced at a Ni recovery of 62.5% (relative to the feed to grinding), with no utilization of slimes dispersants. Another 16.6% Ni recovery was achieved in scavenger flotation resulting in a total Ni recovery of 79.1%. Batch flotation tests using various flowsheet configurations to optimize the grinding, desliming, reagentizing and flotation conditions are in progress.

Jan 1, 2014