Search Documents

By W. Doherty, P. C. Lightfoot, V. A. Fedorenko, N. S. Gorbachev, V. I. Kunilov, A. J. Naldrett, Z. Johan

Paper presented at the conference Economic geology in Europe and beyond II, models for mineral deposits in sedimentary basins, held in Keyworth, UK, 13-14 April 1994. A model is presented which regards the Lower Talnakh- and Talnakh-type intrusions as part of the plumbing system for the overlying lavas. As magma ascended along the Noril'sk-Kharayelakh fault it was forced to spread out within sedimentary strata immediately beneath the obstruction of the accumulated volcanic sequence. Here it was severely depleted in chalcophile elements by sulphides, which were then trapped by their high density and remained behind in the main arteries to form the central, elongated zone of maximum thickness. Subsequent magma also lost Ni, Cu and PGE to the sulphides as it flowed through. The Lower Talnakh-type intrusions represent part of the plumbing system that became blocked at an early stage, before the influx of much mokulaevsky-type magma rich in chalcophile elements. The model accounts for the high metal content of the ores in comparison with the size of their associated intrusions, the extensive metamorphic aureoles, the chalcophile depletion of some overlying volcanic suites, the presence of the ore in near-surface intrusions rather than deep magma chambers, and the sulphur isotopic composition of the ore

Apr 1, 1995

By A. Hemami

In order to automate the operation of mechanical loaders it is essential to have a knowledge of the forces that act on the bucket and of the trajectory that the bucket should follow. A trajectory for the cutting edge of a bucket is derived from studies of the forces acting during the scooping phase. The proposed trajectory has a minimum energy consumption and is simple to automate. It is determined initially by setting to zero certain components of the resistive forces to the bucket motion which would otherwise result in unnecessary work and consequent energy wastage. The method for finding the appropriate trajectory is discussed on the basis of the properties of the material to be loaded and the loader size.

Jan 4, 1993

By H. B. Bell, L. C. Smith

Measurements have been made of the activity of 'FeO' in 'Fe0'-Mn0-Ti02 melts at 1475 degrees C. The results obtained are discussed in terms of ideal mixing of titanates and in terms of a regular solution model. On the basis of the regular solution model activities of Ti02 and MnO in the Fe0-Mn0-Ti02 and Mn0-Ti02 systems have been derived. The data have been shown to be consistent with the liquidus lines in the phase systems. Examples are given of the application of the data to slag-metal equilibria, being used to derive slag-metal data between liquid iron and Fe0-Mn0-Ti02 slags

Dec 1, 1971

By A. B. Holland-Batt

Deposition velocities play an important role in many fields of engineering and an impressive range of measured data has accumulated in the literature. Numerous workers have addressed the problems that are associated with the prediction of deposition velocity because of its particular relevance to the design of pipelines and pumping stations. However, despite this extensive effort, the calculation of friction heads still requires reference to experimentally based graphs to determine Durand factors and there is still scope for improvement in the prediction of the deposition velocity at different solids concentrations. Equations to characterise the relationship between the Durand factor and the volume concentrations of solids in the slurry are presented. A correlation for the prediction of the deposition velocity is also developed and tested against some of the classical experimental data. The application of predicted values of deposition velocity in assessing the potential for the sanding-up of spiral separators is then described and a case study is presented.

Jan 12, 1992

By Gibson J.

The writer hopes to prove that the economical tram is of even greater importance than, say, the economical engine, and as no difficult and involved calculations are required, and all the governing facts are simple and well known, the former is more easily attainable than the latter. In the first section of this paper the factors that determine the size and the construction of the tram are examined; whilst in the second section the road on which it runs is dealt with

Dec 1, 1916

By K. M. Kinealy, A. R. Ramsden, D. H. French

A negative correlation exists between sphalerite composition and gold content when gold is transported as Au(HS)2(-); however, there are spatial and temporal differences within a single deposit. A previous model for the formation of volcanogenic massive-sulphide deposits within thermally intensifying and waning hydrothermal sytems in much the same way as is observed around modern sea-floor vents is supported. The results also emphasise that recognition of the mechanisms of gold transport in ancient deposits depends critically on an understanding of their mineralogy and stratigraphy

Jan 1, 1991

By M. Thompson, B. Coles, M. Hale

The use in regional geochemical reconnaissance of replicate analysis of natural coatings of iron and manganese oxides on the surface of pebbles in stream sediment is described. Pebble coatings were selectively analysed for their relative contents of absorbed trace elements by ablating a small quantity of the coating with a laser beam and sweeping the aerosol obtained into an inductively coupled plasma atomic emission spectrometer. Using this procedure, a geochemical survey in northwest Wales revealed anomalous concentrations of Cu, Mo, As, Zn, Cd, Pb and Co in the pebble coatings of streams draining the mineralised Coed-y-Brenin diorite and the Dolgellau gold belt.

Jan 4, 1992

By J. A. Franklin, E. Broch, G. Walton

To make the best use of rock core, the mechanical character of the rock should be evaluated concurrently with conventional geological observations. The advent of simple techniques, such as the point load 'nutcracker' test, makes field logging of mechanical properties competitive with sampling and testing in the laboratory

Dec 1, 1971

For the convenience of those who are unfamilar with thermodynamics, the following brief description and explanation is given of the thermodynamical terms and methods used in this book. It must, however, be strongly emphasized that the account given below is not an introduction to chemical thermodynamics; its sole purpose is to give the reader a rough understanding of the methods used in the earlier chapters. For further information, reference must be made to the standard textbooks on chemical thermodynamics by Glasstone.

Jan 1, 1953

By J. R. Budden, P. A. Spencer, J. Barrett

The initially produced arsenic (III) is very toxic to the unconditioned culture but the mixed culture has the capacity to oxidise it to arsenic (V) in the presence of iron (III). It was possible to build up the resistance of the culture through progressive sub-culturing on arseno-pyrite until it could tolerate steady-state concentrations of 30 mM arsenic (III) and 200 mM arsenic (V). With some samples tested in the continuous systems the final arsenic concentrations reached 330 mM. It proved possible to use the laboratory batch data to establish the optimum operating conditions for continuous test systems with capacities of up to 32 m3. Data on the residence time, oxygen uptake rates and gold extraction from the bio-oxidised residues could then be confirmed by continuous testing without the need first to use empirical means to determine optimum conditions for continuous bio-oxidation. The data on residence time, oxygen uptake rate, solids density and neutralisation could be used to estimate the capital and operating costs of treating any given tonnage of the concentrate of interest. It was established that the arsenopyrite concentrates can be suitably bio-oxidised to cause the liberation of at least 90% of the gold content. The method is simple to operate and is flexible over a wide range of external conditions

Apr 1, 1991

By S A. M Crawshaw, J A. B Fortune

Trackless battery powered haulage vehicles have been in operation in British coal mines principally for longwall face transfer and personnel transportation. Changes within the industry have resulted in the introduction of room and pillar coal mining methods and the introduction of increasingly heavier longwall roof supports This has resulted in the introduction of: • Battery powered coal haulage machines, which, without the need for trailing cables, increase productivity within room and pillar mining. • Battery powered longwall shield haulers which are capable of carry ing the heaviest shield supports currently being utilised within the British coal mining industry. The conventional machines have been adapted from an American design to meet the requirem ents of European legalisation. This has seen the- emphasis being placed upon the supplier with the European M achinery Directive being introduced, necessitating the assigning of a 'C E ' m ark to each vehicle. Battery vehicle technology has advanced to meet the demands of the ever changing market and will no doubt he further adapted to meet the requirement of the British coal mining industry.

Jan 10, 1996

By B. H. Smith

"Most of the discoveries of nickel sulphide deposits in Western Australia have followed the search for gossans. The chances of further discoveries depend on improving our understanding of the cover of strongly leached and transported materials that obscure approximately 85% of the area of the Yilgarn Block that has nickel sulphide mineralization potential. The lateritic profiles that are observed on the Yilgarn Block today were formed over a period of more than 100 m.y. of warm and humid climates. This lateritized land surface has been preserved by induration during subsequent arid climates as well as by the structural stability of the Yilgarn Block.In geochemical surveys of lateritied terrain samples have to be taken from at least the saprolite zone usually by drilling so that confident predictions can be made of the significance of analytical data. Account must be taken of the mineralogy of samples, as well as the nature of the horizon of a laterite profile that is being sampled, owing to the concentrating effects on trace elements of Fe and Mn oxides.Multivariate techniques have been applied successfully to analytical data in gossan recognition when textural evidence is ambiguous. Pathfinder geochemistry has also been used in gossan recognition and the most significant recent advance has come from studies of platinum group metals in nickel sulphides and their dispersion during weathering."

Jan 1, 1984

By D. A. White

A simple model for hydrocyclone classification based on the crowding theory first put forward by Fahlstrom is presented. This is a mechanistic theory that postulates that the behaviour of a hydrocyclone is the result of an ordered process that is independent of its dimensions. The main variables that describe the process are the fractions of feed solids and water that are ejected from the underflow. A simple model is developed from basic properties of the classification process and is compared with theory. Agreement is good but improves when the cyclone has a high solids content

Dec 1, 1991

By R. W. Ruddle

"Besides copper, iron, silicon, and oxygen, a large number of elements may be present in copper ores, the more important of which are zinc, lead, arsenic, antimony, bismuth, selenium, tellurium, nickel, cobalt and the precious metals; impurities of less importance are calcium, magnesium, aluminium, barium, sodium, potassium, manganese, lithium, fluorine, titanium, uranium, vanadium, tin and molybdenum. All of these elements are eliminated to some degree in the subsequent roasting, smelting and converting operations.Information on the elimination of impurities during the smelting of copper is surprisingly meagre, however, rather more information is available on impurity removal during the smelting of the ore in reverberatory or blast furnaces."

Jan 1, 1953

By A. M. Marabini, S. Battaglia, M. Ciriachi

A computer program has been developed that produces graphic representations of the atomic structure of any crystallographic plane of a mineral. The information provided by the program relates to a purely geometrical model of the crystal structure in which each atom is represented solely by the x, y and z coordinates of its centre. Despite its simplicity, the program can be used as a first approximation model in studies of the interaction between mineral processing reagents and the surfaces of mineral grains which are assumed to be coincident with cleavage planes.

Jan 4, 1992

By C. C. Harris

The use of Alyavdin's equation Y(x,t) = 1-e(-bt) for describing the effect of grinding time on size distribution is discussed. The equation transforms into linear form by expressing it as log-log reciprocal (1 - Y) versus log t. For plotting, specially divided grids are available; Rosin-Rammler or Weibull charts may be used. The data of Herbst and Fuerstenau are especially useful for illustrating the Alyavdin-Weibull chart in two applications: (1) presenting data (which are relatively unaffected by experimental scatter) and comparing them with theoretical predictions, and (2) as a test for the zero-order kinetics production hypothesis. The chart based on the Alyavdin-Weibull equation is suggested as a useful aid in the analysis of kinetic data (/ versus f), though not as a procedure in its own right. Proposed applications are (1) displaying data with excellent clarity, since it avoids the kind of congestion inherent in some other plotting methods, and (2) as a test for assumed kinetic relationships. Sometimes, equation 1 describes the data quite closely, and in these cases the parameter values appear to be related to certain operating conditions.

Dec 1, 1971

By J. P. Rees

Describes methods of dust-sampling such as weighing the dust caught on cotton-wool, the sugar tube, konimeter, circular konimeter and the thermal precipitator. Covers the work of mine dust inspectors, the Miners' Phthisis Prevention Committee and the Chamber of Mines Dust Department.

Jan 1, 1947

By G. H. Blackwell

Sequences in open pit mining must be planned and regularly revised to incorporate changes in the variables which affect profitability. Interactive computer planning with colour graphic facilities is an effective tool for this purpose in the short and medium term. An interactive computer planning system for medium-size, low grade porphyry copper-molybdenum open pits is described. The planning system proved especially valuable during the critical stages of pushback mining when deep, inner pit ore was nearly depleted and the erratic grades of the next pushback provided ore and marginal material at a time of depressed metal prices.

Jan 8, 1993

By R. P. Foster, ed.

The short selection of papers in the special issue provides an insight into the level of exploration activity in Africa and the science and technology that are underpinning it. A country-by-country survey is followed by discussion of geochemical exploration in tropical soils, the Liptako region of Niger, structural styles of deposits in Zimbabwe's Bulawayo-Bubi greenstone belt, structural controls in Zimbabwe's Eldorado shear zone, the regional framework for deposits in the Odzi-Mutare-Manica greenstone belt of Zimbabwe and Mozambique, and the Iperindo deposit in Nigeria's Ilesha schist belt

Apr 1, 1996

By T. J. White, R. A. Farnfield

Early computerised blast monitoring equipment consisted of a digital version of the existing analogue machines with, perhaps, a few enhancements. Many additional facilities have since been developed to enable the efficient collection of high quality data. These developments are examined with reference to digital sampling, triggering systems, the storage of complete recordings and signal processing. Recent advances have been made in the use of blast monitoring systems that comprise multiple blast monitoring locations with centralised control and data collection. Software has been developed to help record blast parameters and assess environmental effects. Computer databases have many advantages over their paper counterparts. Data can be easily retrieved and processed. The scaled distances used in the prediction and control of peak particle velocities can be calculated rapidly when the data are obtained directly from a database. Since the whole vibration signal can now be recorded, signal processing can be used to provide information such as signal length, dominant frequency and response spectra.

Jan 4, 1993