Search Documents

During the construction of storage caverns, and during their lifetime if the use to which they are put so requires, it is necessary to provide adequate ventilation to ensure the safety and comfort of the underground workforce. An analysis of likely contaminants during construction has indicated that where a large facility is situated in a rock mass of even moderate temperature climatic conditions are likely to be the limiting factor during most of the mining operation and atmospheric pollution when blasting is undertaken. Possible options for improvement are increased air flow, cooling of intake air and reduction of the heat source by altering the number and type of haulage units employed in the cavern. Local solutions are an alternative approach where heat problems are confined to a few specific locations

Aug 1, 1994

By M. J. Scoble, L. M. Daneshmend, C. Hendricks

Paper presented at a meeting on: Artificial intelligence in the minerals sector, held in Nottingham, UK, 20 April 1993. An attempt is made to relate emerging technologies to education and training requirements by examining the nature of the Canadian mining industry's human resources. Particular attention is given to the trends evident in mine automation and their likely impact on instructional needs. The characteristics of "computer-aided instruction" systems are reviewed and related to the implementation and support of mine-wide monitoring and communication networks, which are seen as fundamental to the eventual automation of underground hardrock mines

Apr 1, 1994

By F. Tailoka

Bi was electrorefined from alloys containing 10-90 wt% Pb, together with Cu and Ag as minor impurities, in a basic cell and in a recessed-channel cell with 27.5:72.5 NaCl-PbCl electrolyte at 450-470 degrees C and 10 000-20 000 A/m2. The voltage in the basic cell was as high as 9 V, with some carryover of Bi to the cathode observed, whereas in the recessed-channel cell it was as low as 285-635 mV. Flow patterns observed in a room-temperature model indicated that the recesses provide both static liquid hold-up and good mixing of the alloy, enhancing cell performance in combination with the reduced anode-cathode distance of 0.90 mm. The purity of the resulting anode product is as high as 99.9%

Aug 1, 1995

By B. E. Burakov, S. D. Lupal, O. A. R. Thalhammer, B. Saini-Eidukat

Electric-pulse disintegration is a mineral separation technique that liberates all mineral grains from any igneous or metamorphic rock irrespective of its lithology or grain-size distribution. The normal mechanical crushing of whole-rock samples is replaced by the rending effect of an explosion, produced by applying an electric current from a high-voltage power source. A voltage greater than the 100 kV necessary for the electrical breakdown of rock samples is achieved by using capacitors charged in parallel, but discharged in series. The sample sits in a water bath and the rapid distribution of electric pulses leads to an explosion which occurs preferentially along grain boundaries of the sample. Individual, undamaged mineral grains can be recovered in their original shape and form regardless of grain size. Examples are given of the liberation and concentration of important accessory minerals from different rock types. The examples show the recovery of diamond from two types of non-kimberlitic host rock in Popigai and Kumdykol in Kazakhstan and platinum group minerals associated with chromitites from the Konjdor intrusion and sulphides from intrusions in the Kola Peninsula in Russia

Apr 1, 1995

By A. Dean, J. Roberts, I. Stone, J. R. Merefield

Paper presented at the conference: Risk assessment in the extractive industries, held in Exeter, UK, 23-24 March 1994, and first published London: IMM, 1994, preprint volume, 10pp., 11 refs. No completely reliable method for characterising and quantifying airborne dust risk exists. A new monitoring technology has been developed whereby dust collected from four-way directional and high volume samplers is analysed for mineral content and particle size for integrated dust mapping. A dust database was set up for the area surrounding the Ffos Las open cast coal site in South Wales. It included XRD directional traces from 17 gauges over 20 months, XRD traces from window ledges in the nearby communities, the major soil types in the area, dust data from haulage roads and public roads and reference-type mineral samples. The database can be accessed relationally to compare and analyse the data using mineral, direction, time, weather and geographical relationships. The data has been used to assess areas of low, intermediate and high levels of risk from dust fall-out

Apr 1, 1995

By G. G. Barbante

An understanding of the thermodynamics of smelting copper anode slimes is a prerequisite for improvements to the process. During slimes smelting, a silver-copper selenide matte is formed and subsequently oxidised to silver metal. As part of a series of investigations, molten silver selenide matte was oxidised at 1 100 degrees C with pure oxygen. The chemical potential diagram for the system was developed and used for qualitative prediction of the results of the experiments. A simple, computational thermodynamic model of converting is presented, the adjustable parameters of which were determined by matching the model with the experimental results. The practical usefulness of the model was demonstrated by predicting the effect on silver recovery of smelting temperature and of using either oxygen or air as the smelting gas

Jun 21, 1905

By S. G. Ozkan

An investigation was carried out into the effect of physical parameters, such as particle size of the sample, residence time, solid/liquid ratio and impeller speed in the flotation cell, on the solubility in soft tap-water of colemanite (calcium-bearing borate) from Emet, in Turkey. Solubility increased steadily with residence time from 5 to 20 min but only minimally thereafter. There was a similar increase with impeller speed from 500 to 1 500 rev/min, beyond which a solubility of around 1.05 g/l was again established. There was a slight decline in solubility as the solid/liquid ratio was increased from 1 to 30%, with stable values around 1.05 g/l at a 20% ratio, while a sharp decrease was observed with decrease in size down to the -20 micrometre fraction. The effect of solubility should be taken into account if the application of a wet-processing method is being considered for the ore, while it can also result in losses of material during handling and storage

Jun 21, 1905

By J. A. Finch, D. Lin

The robustness of the large-sections correction procedure, Hill's fast approximation, Barbery's correction and the PARGEN correction was examined by comparing their ability to reconstruct the true liberation distribution using sectioning data from computer-generated spheres. The results indicate that the flexibility of a correction procedure is related to the assumptions it makes about the continuity of the liberation distribution, locked-particle characteristics and ore texture. Overall, the large-sections procedure appeared to be the most generally applicable. The Hill fast approximation performed well, but this was probably because it partially incorporates the sphere model; the performance of the PARGEN and Barbery corrections varied from case to case.

Dec 1, 1995

By C. S. Spirakis, A. V. Heyl

Paper presented at the conference Economic geology in Europe and beyond II, models for mineral deposits in sedimentary basins, held in Keyworth, UK, 13-14 April 1994. The modified basinal brines, containing partly oxidised sulphur species, scavenged metals from basement rocks and sediments and transported them through the host rock, which contained local concentrations of organic matter. Reacting in various ways with the mineralising solution as temperatures at the sites of mineralisation changed, organic matter caused the precipitation and dissolution of a variety of minerals in the ore zones; it was organic matter that caused all of these reactions to occur at the same sites. Thus all components of the mineralising fluid - salt, water, heat, sulphur and metals - were obtained within the ore district. The siting of the mineral districts was related to the locations of faults through U- and Th-enriched granites beneath sediments containing basinal brines, and the locations of ore deposits within the districts were controlled by local concentrations of organic matter

Apr 1, 1995

By L. J. Cabri

Although no complete mineralogical balances have been published, the background knowledge and proven, highly sensitive analytical techniques to produce them already exist. For PGE-Cu-Ni sulphide ores a combination of ore microscopy, image analysis and electron microprobe analysis with proton microprobe analysis of sulphides for Pd, Rh and Ru and ion microprobe analysis for Pt, Ir and Rh (in some minerals) should provide the necessary data when combined with reliable assays. Other sulphide ores, such as the Cu-Ni-(PGE) ores of Sudbury, Ontario, require a similar approach except that the ion microprobe would be more suitable for the analysis of Pd, Pt and Rh because of its greater sensitivity. Oxide-silicate ores may be harder to deal with quantitatively, although the potential to confirm the presence of trace PGE within silicates and oxides may be greater than in PGE sulphide and Cu-Ni-(PGE) sulphide ores. However, solid solution of PGE in oxides and silicates still requires thorough documentation and evaluation in terms of their significance for the overall metallurgical balance

Apr 1, 1994

By I. R. Hanby

A simple solution to the problem of whether to round the calculated number of trucks up or down to the nearest whole number is to adopt as criterion the minimum cost per unit volume/mass moved, assuming all trucks in the fleet are of the same type. When the effects on journey time of varying haul-road slope are calculated for several rolling resistances, it is shown that the optimum angle of 7.5 degrees is moderately independent of both rolling resistance and height climbed; the lower the resistance, the lower the sensitivity to ramp angle, but if haul-road gradients do not exceed 1 in 10 (5.7 degrees) for safety reasons then travelling time will never be more than 7% greater than its theoretical minimum. Further calculations result in a graph of the maximum payload values to incur the minimum cost, for different values of total effective resistance

Jan 1, 1991

By G. Richards

Research shows that having more women in the top mining jobs can bring bottom-line benefits. Mining companies are starting to embrace the need for greater gender diversity at board and senior management levels, figures and examples are given.

Jul 1, 2015

By Jinsheng Chen, S. S. Peng

The relationship between support performance parameters and parameters representative of mining and roof conditions is characterised by uncertainty, non-linearity and dependence, so the theory of artificial neural networks was selected as a basis for shield design. A computer program based on a back-propagation training algorithm was written to derive the weighting factors between inputs and outputs from field data; once these had been established two mathematical models were developed to describe the relationship. Back-calculation of field data indicates that the results generated from the neural network models are much more accurate than those derived by traditional methods and can be used with a higher level of confidence. The support density, possible yield frequency of face supports and interval of periodic roof weighting under specific mining and roof conditions can be determined by application of the models

Jun 21, 1905

By G. G. Barbante

Anode slimes produced during copper electrorefining are a valuable source of silver, gold, selenium and tellurium. The conventional pyrometallurgical process for treating slimes involves preliminary leaching in sulphuric acid followed by smelting in a reverberatory furnace with fluxes, but it is slow and has many recycle streams. The chemistry of the phases and the reactions that occur in slimes smelting are poorly understood and and this prevents major improvements to the process. Laboratory-scale experiments were conducted using unleached slimes, with and without the addition of fluxes and under neutral, oxidising and reducing conditions. Results show that selenium is readily removed as gaseous selenium dioxide and that molten Cu-Ag-Se-O phases form when fluxes are added. Oxidation-refining of these phases by air injection and flux addition can result in the formation of silver suitable for further electrorefining

Aug 1, 1995

By G. S. Camm

Gwynfynydd is a small, high-grade black shale-hosted vein-gold deposit. The Chidlaw Link Zone is the only area being mined and contains 24 000 t ore grading 15.2 g/t gold. Within the Link Zone a complex vein structure occurs consisting of a mother vein up to 5 m thick and narrow (less than 0.5 m) leader veins. The former shows minor variations in dip, strike and thickness, whereas the latter show marked changes in all three. The leader veins are hosted within the footwall zone of the mother vein and both are composed of quartz with galena, sphalerite, chalcopyrite, pyrite and minor arsenopyrite. The vein system is transected by a series of cross-vein and intra-vein dip-slip faults. Pockets of gold occur at vein intersections or branches and within the complex footwall zone and are often related to variations in vein attitude and/or geometry. The Chidlaw Link Zone displays a complex, erratic distribution of gold mineralisation and a multi-stage history of structural activity, fluid flow and mineral deposition

Jun 18, 1905

By Xiao Min You, D. R. Swonbourne

Smelting of Cu anode slimes involves the use of a slag to hold the oxidised Cu, but some Ag is also inevitably oxidised to the slag. The solubility of Ag in sodium silicate slags at 1 100 and 1 150 degrees C has now been determined over a very wide range of oxygen partial pressures. Silver was found to be present in the slags both as neutral atoms and as AgO(0.5). The activity coefficient for atomic Ag was a very strong function of slag composition and temperature, whereas that for AgO(0.5) was much less affected by slag composition and was almost independent of temperature over the limited range examined. The results reveal that the dissolved Ag cannot be fully recovered by reduction of the slag with very reducing gases

Jun 21, 1905

By J. A. Hudson, D. L. Millar

Paper presented at a meeting on: Artificial intelligence in the minerals sector, held in Nottingham, UK, 20 April 1993 (original title: Rock engineering system performance monitoring using neural networks.) Synthetic and analytical approaches to objective-based design of rock engineering projects are discussed. Rock masses are considered as complex dynamic systems with components that concurrently interact with each other and their environment. The existence of a rock engineering system canon (i.e. a set of systems governing rules) is proposed. Its possible components are highlighted and an application is demonstrated using a "rock mass automaton" designed to simulate dynamic heat distribution in rock. In the example given, the canon implements the basic result from probability theory applied to the thermodynamics of solids. Rock engineering system performance is reduced to the mapping of the output of a rockmass to varying input (design) options, within the state space of the systems model. The Kohonen Self-Organising Map provides an extremely useful analytical tool to reduce the hyper-dimensionality of rock engineering system behaviour. Further, the hyper-dimensional state vector is mapped "quasiconformally" such that the neural map tends to spatially organise similar input state vectors, facilitating interpretation of rock engineering system behaviour (performance monitoring). Work is reported on the development and validation of the automation as a basis for an internal representation of the rock mass bahaviour. The results are reported of simulations compensating for the uncertainty of the exact mechanisms operating within the rock mass, using additive noise with the input state vector in the training stages of the self-organising map implementation. Initial work on adopting Grossberg's Adaptive Resonance Theory neural network architecture for classification of rock engineering systems behaviour is also presented

Apr 1, 1994

By F. T. Da Silva

Concentrates of titaniferous minerals containing around 30 wt% Ta2O5 are processed hydrometallurgically by hydrofluoric acid leaching and solvent extraction, followed by the precipitation of hydrated potassium heptafluorotantalate. A fundamental study of the thermodynamics of this precipitation and recrystallisation was undertaken to increase understanding of the conditions most conducive to the production of pure, well-crystallised K2TaF7. Activity-pH diagrams for the Ta-K-F-H2O system explained the dissolution of Ta2O5 in fluoride solutions quite well and also the precipitation-recrystallisation of K2TaF7.H2O. X-ray diffraction and scanning electron microscopy confirmed the thermodynamic observations. It was concluded that the best precipitating agent for K2TaF7 from fluoride solutions is KF but a recrystallisation step in a HF environment produces purer, well-crystallised K2TaF7.H2O, eliminating oxy-salts and other impurities

Jun 21, 1905

By L. E. Mordberg, E. N. Nesterova

Geochemical studies of the bauxite deposits show that the primary composition is gibbsitic. Some trace elements were relatively mobile during bauxite formation with the content of Th, U and Zr increasing and that of Rb, Ni and Co decreasing. Y and Pb were relatively immobile during lateritisation; their contents and ratios were inherited from different types of underlying rocks. The supply of Ni and Co took place at the diagenetic or epigenetic stages; their ultimate source was the crystalline basement in the region. The studies support the view that the bauxite was likely to have originated as a result of in-situ lateritisation and not through sedimentary transport and redeposition

Jun 18, 1905

The reduction of zinc from slags by a molten, carbon-saturated bath was examined in a laboratory study under conditions of continuous slag feeding. The results show that it is possible to reduce the bulk of the zinc from the slag before there is a net reduction of iron. However, the recovery of zinc was not as high as in batch tests performed in an earlier study. Lead in the slag was reduced simultaneously with the zinc to very low levels and was volatilised. Copper in the slag was reduced and dissolved in the alloy. An attempt was made to identify potentially commercial ways of treating zinc slags using an iron bath. The approaches that appear to have the greatest potential are reduction in a batch process using electrical heating and reduction in a continuous process with co- or countercurrent flow of the slag and alloy. In the latter the alloy would be prepared in a separate furnace before being contacted with the slag. The purpose of this would be to superheat and carburise the alloy so that no additional heat or reductant would have to be supplied in the slag-alloy reactor

Jul 1, 1991