Search Documents

By Richard J. Mainiero, Michael S. Wieland, Harry C. Verakis

The Bureau of Mines, U.S. Department of the Interior, has been conducting research on delay blasting in underground coal mines in support of the efforts of Mine Safety and Health Administration (MSHA), U.S. Department of Labor, to revise coal mine blasting regulations. Part of the research centered on developing an understanding of the factors that lead to misfires of permissible explosives. Research was conducted to determine whether frequency of misfires was related to borehole spacing. For a wide variety of permissible explosives, misfires were observed for about 50 X of the holes at 45-cm (18-in) spacing. Misfires were also observed for 60-cm (24-in) spacing, but the frequency of misfires was much lower than observed for the 45-cm (18-in) spacing. The Bureau has recommended that hole spacings of less than 60 cm (24 in) be prohibited.

Jan 1, 1986

By Ginn Huh

The blasting work to construct a subway in Seoul, Korea have often caused increased neighbor’s complaints because of ground vibration. In order to prevent the damage to the structure, it was necessary to predict the level of blasting induced vibration and to determine the maximum charge weight per delay within an allowable vibration level. The effect of blasting pattern, rock strength and different explosives on the blast-induced ground vibration was studied to determine the maximum charge weight per delay within a given vibration level. The blasting vibration was measured from 10 sites along the subway line in Seoul and an empirical particle velocity equation from over 100 test data was obtained, V=K(D/W1’3 )-” , where the values for n and K are estimated to be 1.7 to 1 S and 48 to 138 respectively.

Jan 1, 2000

By Robert McClure, Carlton Lehman

Rendering safe explosives in an urban environment presents a unique challenge due to the safety concerns and disruption to the general public. Potential damage to the surrounding homes, businesses, utilities and transportation infrastructure are some of the major concerns when planning the render-safe operation. Engineering controls to mitigate blast effects, such as damaging air over pressure levels, material ejection and ground borne vibration, need to be implemented as part of the operation. Monitoring of seismic and air overpressure during these operations are needed to protect against potential claims when controlled or unplanned detonations occur.

Feb 1, 2020

By Deepankar Das, Gulshan Kumar Sadhwani, Jyoti Prakash Sahoo

Sindesar Khurd Mine (SKM), the largest underground mine in the Hindustan Zinc Limited portfolio, is located approximately 60 kilometers (37 miles) north of Udaipur. In the 2018 financial year SKM achieved an annual ore production of 4.5 Mt (4.42 million LT) and mined metal production of 247 kt (243,099 LT).

Jan 1, 2019

By Robert McClure, Carlton Lehman

Rendering safe explosives in an urban environment presents a unique challenge due to the safety concerns and disruption to the general public. Potential damage to the surrounding homes, businesses, utilities and transportation infrastructure are some of the major concerns when planning the render-safe operation. Engineering controls to mitigate blast effects, such as damaging air over pressure levels, material ejection and ground borne vibration, need to be implemented as part of the operation. Monitoring of seismic and air overpressure during these operations are needed to protect against potential claims when controlled or unplanned detonations occur. Two recent render-safe operations conducted in and around urban environments dealt with deteriorated, sensitive dynamite and damaged blasting caps. Utilizing innovative neutralization chemicals and processes to render-safe the deteriorated dynamite, while protecting the general public, proved to be the safest, most environmentally responsible and cost-effective way to approach the problem. In both cases, the explosives, old dynamite and detonators were found in abandoned, unlocked magazines. The dynamite was in a significantly deteriorated state, which was evident due to the nitroglycerine found leaking in,around and under the dynamite cartridges. Iron wire permissible electric blasting caps were also found in a corroded condition with exposed explosives and un-shunted lead wires. With occupied buildings within 180 feet (54.86 meters) of the magazines, any procedure (e.g. transporting, countercharging, burning) that could potentially cause a detonation was not an option. In the event of an unplanned detonation during neutralization operations, several blast mitigation methods were employed to safeguard the site. This operation and a similar one with over 1,000 pounds of crushed and buried leaky dynamite were unique since all the explosives were rendered-safe and neutralized on site. The use of advanced neutralization products and filtering processes allowed for a safer, more environmentally responsible way to resolve the problem. The magazines and all residual solids and fluids were tested and confirmed by independent labs to have no explosives residues. The effluents were treated on site, tested and met safe levels, so they were disposed of at a local municipal wastewater facility.

By P. D. Lightfoot, C. Badeen, R. Turcotte, D. E. C. Jones

Following localized (i.e. hot-spot) ignition, there is a minimum pressure required for combustion to propagate in water-based commercial explosives. The latter is usually referred to as the ‘Minimum Burning Pressure’ (MBP) of the explosive. In the present work, both an apparatus based on hot-wire ignition and an associated methodology were developed to measure the MBP of water-based explosives. It was demonstrated that the MBP constitutes a sharp pressure threshold below which the probability of inducing sustained burning in these explosives becomes very small. It was found that each emulsion explosive tested has a distinct MBP value, which depends critically on its formulation. It appears that this test may offer a firm basis for the classification of emulsion explosives for regulatory purposes.

Jan 1, 2004

By Dale Ramsey

As someone who has enjoyed photography as a hobby for many years, aerial photography to me has always been an exciting way to give a different perspective to my images. Our industry is always in search of new technology for bet­ter and more cost effective methods to improve our trade and aerial photography is a great tool to improve project planning or document its progress. It has typically involved conventional aircraft both fixed wing and helicopters but neither method is always available or cost effective. The lat­est innovation since digital imaging is the development of Unmanned Aerial Vehicles (UAVs) or drones. But there is a lot of uncertainty with this amazing new technology’s fu­ture in the U.S. as the Federal Aviation Administration (FAA) is under review and development of UAV regulations for commercial use which are slated to be completed in 2015.

Jan 1, 2015

By Catherine T. Aimone

A series of experiments have been performed to characterize fragmentation and microcracking in quartz monzonite copper porphyry. The flyer plate impact method was used to generate plane shock waves in rock specimens for impact pressures between 1.6 and 7.3 GPa and impact pulse durations between 1.1 and 7.0 µs. The effects of pressures up to 4.8 GPa and pulse duration on fragment size distributions and microcrack densities were studied. The results show that pressures effect particle sizes to a greater extent at higher pulse durations. However, changes in pressure and pulse duration show little influence on the density of microcracks induced during explosive loading. These results indicate that the nucleation and growth of microcracks in rock subjected to shock waves occur uniformly throughout. A substantial decrease in particle sizes for high pulse durations is attributed to more time allowed for microcracks to grow and coalesce, forming individual particles.

Jan 1, 1985

By Lon D. Santis

The Code of Federal Regulations Title 30, Parts 56, 57, 75, and 77 require that detonators and explosives be separated by four inches of hardwood or equivalents when transported together in mines. This standard was developed to protect the explosives from initiation by the more sensitive detonators. The research reported here is an attempt to quantify the fire protection offered by four inches of red oak and other materials. Boxes with a volume of 6.75 cubic feet were made from four-inch thick rough green oak (RGO), two-inch thick RGO plied, two-inch thick #1 common (dried) red oak plied, and a metal/plywood composite. These and boxes meeting the Institute of Makers of Explosives' (IME) Safety Library Publication No. 22 were tested in bonfires. The boxes were instrumented with thermocouples, filled with detonators, and placed over a kerosene fire imparting about 16 kilowatts per square meter heat flux for up to 3 hours.

Jan 1, 1997

By Tom Watts

The practice of pumping bulk blasting agents is regulated by many agencies around the world. The explosives manufacturers have done an excellent job of hazard and operability studies allowing criteria to be established for the safe pumping of water based blasting agents. The challenge of a Bulk Trucks or Mobile Manufacturing Units (MMUs) manufacturer is to take the objectives of the regulatory agencies and the explosives manufacturers and responsibly design and build MMUs that are safe, compliant, and cost effective without compromising serviceability.

Jan 1, 2011

By Ulf Nyberg, Changping Yi, Daniel Johansson, Håkan Schunnesson

To investigate the non-ideal detonation properties of aluminized emulsion explosive, a series of tests for an emulsion explosive with 5% aluminum powder additive were carried out with mortar confinement. The velocity of detonation (VoD) and the curvature of the detonation front for different charge diameters were obtained from the tests with a high-speed camera

Feb 1, 2020

By Calvin J. Konya

Backbreak behind the last row of boreholes can be a significant problem for blasting operations. Backbreak will interfere with the proper drilling and execution of the subsequent shot and can produce well defined boulders, which will not be broken by the subsequent shot. In order to determine the effect of timing on backbreak, a full scale blast with 6 1/2 inch boreholes was used to test the effects of timing. The test site was a quarry which had suffered from severe backbreak regardless of the blasting pattern or explosive used. One half of the production blast was loaded and initiated using the current technology at the quarry, the other half of the blast was deliberately timed in such a manner as to minimize backbreak. The timing was such to allow for ground movement in one row before the subsequent row fired. The test results proved that the amount of backbreak and flyrock could definitely be controlled with the selection of the proper borehole timing.

Jan 1, 1987

By M Sampara, W Comeau

The introduction of large-diameter holes to underground mining has made possible the development of new mining methods such as the Vertical Crater Retreat (V.C.R.) method. It is not only the safest underground excavation system but also provides mass production at a lower cost than any conventional mining method (1, 2, 3, 4, 5).

Jan 1, 1981

By Matt Brandon

This case study demonstrates how integrating drone and GPS surveying with 3D modeling software creates more effective blast designs that address specific geotechnical challenges while improving safety and blast performance. In this case study an 80ft (25m) highwall experienced recurring slip plane failures exacerbated by a previously mined 40ft (12m) bench that removed back support, creating an unstable triangular rock mass. Previous blasting along this wall displaced the upper 40ft (12m) of material, opening geological discontinuities and causing progressive slope failures that compromised crew safety and blast effectiveness. High-resolution drone photogrammetry, GPS surveying, and laser measurements were employed to precisely map slip planes, bedding planes, and fault structures within the bench geometry. These geological features were imported into 3D design software to develop a shot pattern that strategically utilizes natural rock discontinuities rather than working against them. GPS-guided hole placement ensured accurate field implementation, while marking geological features on the surface of the bench provided visual references for the blast crew. The final blast design positioned the last row of holes to break preferentially along an existing slip plane while avoiding intersecting the next slip plane behind the blast. Explosive loading and timing sequences were adjusted based on the hole location relative to the 3D geological model to optimize fragmentation while maintaining wall stability. The optimized design improved highwall stability significantly, by reducing the slip plane failure mechanism that had previously compromised operations. Measurable improvements included enhanced highwall stability, reduced back-break, improved blast performance, and reduced safety risks for equipment operators and blast crews. Two subsequent shots using identical methodology were able to remove the rest of this problem area, confirming the repeatability and effectiveness of this integrated approach. This methodology demonstrates practical integration of surveying technologies with geological understanding to solve complex blasting challenges. Accurate 3D modeling of geological features enables blast designers to work with natural rock structures rather than against them, resulting in safer, more effective blasting practices. This case study shows the value of understanding the precise locations of geological features for optimizing blast design and provides a replicable process for addressing geotechnical challenges in blasting operations.

Jan 26, 2026

By Ayman Tawadrous, Hendrik Botha, Simon St J Tose

The early miners and their mules always had the challenge of transporting unstable dynamite underground. The modern pumpable explosives, whilst far safer, still present a major logistics challenge for the mobile charging units (MCU). The challenge today is the efficient explosive delivery into declines, ramps, and vertical shafts, often requiring the MCUs to travel excess distances up and down to surface to re-load. Alternatively, the management of cassettes or ISO containers is utilized to deliver the pumpable base emulsion to the MCUs at the working face. Additionally, local laws and regulations regarding shaft clearance further compound the task and result in pausing other operations in the shaft or decline or ramp until the completion of the explosive transport. This paper examines the research & development challenges of dropping base emulsion down a vertical pipe to depths in excess of 1000 m (3280 ft.), either to an underground storage or directly into the MCU, depending on the depth. The boreholes (with pipes) are drilled in close proximity to the underground work areas. The paper also discusses the rheology of the emulsion within these vertical pipes as well as the economic benefits of such an innovative system. The learnings gained from this work, along with examples demonstrating the significant reduction in MCU travel and the safety benefits, are presented for the industry to consider moving forward.

Jan 21, 2025

By Jack Eloranta

This paper compares energy requirements for blasting, crushing and grinding. By tracking electrical consumption for various powder factors, a general trend has appeared. This study involves over 100 million tons of ore and powder factors ranging from .5 lbs/LT to .8 lbs/LT. Actual energy usage is compared to predicted energy based on the Bond equation.

Jan 1, 1997

By Ery Wardhana, Stefanus Jagad, Relinda Sanistya, Hasucita Tausi, Rido Situmorang

The blasting process is one of the most high-risk activities in mining operations. Shotfirers and blasting crews face hazards from slope failure, toxic gas and fumes, or unstable ground condition every day of the blast. But on the other hand, to ensure all of the holes are detonated, shotfirers are required to reenter the location to check. With advances in technology, nowadays the use of drone in mining is not something that is rarely seen. It has been used for mapping and slope-monitoring. This paper will discuss the application of drone for blasting process in a mining pit in East Kalimantan, Indonesia. By using drones, it is not only safety factor which can be improved but also operational efficiency and technical analysis. The duration it takes for post blasting process can be reduced because the drone can directly enter the location after blast. The technical analysis for the blast can also become more comprehensive, as the before-after photos and video documentation can be taken with wider view. It helps with fly rock calculation and fragmentation analysis too.

Feb 6, 2023

By Rolf Koenig

After the Dynatronic firing system was demonstrated for the first time at the SEE conference in Miami in 1987, it was officially approved in Germany at the beginning of 1993. Dynatronic has now been on the market for 5 years. At present, it is used in several European countries and successful test series have been running in Australia.

Jan 1, 1998

By Tyler Rockley, Carla Reyes

Autonomous fragmentation measurement systems designed for shovels have been in operation for nearly two decades, however fragmentation systems capable of performing in the dynamic conditions of the front-end loaders (FEL) were only recently introduced to the market. This paper presents an in-depth evaluation of an automated digital fragmentation measurement system specifically designed to perform under the dynamic operational conditions of the FEL in two of Teck’s mine sites. As early adopters of this novel application, Teck embarked on a Proof-of-Concept (PoC) trial phase, defining a set of key performance indicators (KPIs) to qualify the performance of the digital solution in tough mining operating environments. The KPIs focused primarily on the hardware robustness, quality of image and segmentation, both day and night, availability of the system and sample ratio. The benefits expected from using this technology include increasing the safety of the current fragmentation measurement process, improving the quality of the analysis, increasing the sample representativeness, and using the attributes of the system to create an oversize detection alert to inform the loading operation process. A critical part of the evaluation was verifying the system’s effectiveness on the particle segmentation algorithm as this element often gets overlooked, especially when dealing with the large number of samples autonomous systems can generate; minor misclassifications due to inadequate segmentation are often dismissed as they might not be statistically significant, however systematic misclassifications can cause unacceptable deviation in the data and limit the intended application of the technology. The system’s performance was further validated through several tests that involved identifying objects of known sizes to ensure the reliability on the consistency of the particles’ segmentation.

Jan 21, 2025

By Carlos Agreda

The rock blasting environmental impacts such as: flyrock, groud vibrations,airblast,and/or noise, dust and fumes are identified and mentioned. Some comments on the correction factors that might be taken into consideration to calculate the initial velocity and the maximum projection of the rock fragments are mentioned as well.

Jan 1, 1995