Search Documents

By Doug Wathen, Philip M. E Thomas

The City of Fort Myers needed to replace a 40-year old 42-inch storm sewer line in downtown Fort Myers with a new 54-inch line to accommodate population growth. The old line had to be kept operational while a new line was installed. The contractor spent two months using a drop ball, a hoe ram, and large rippers trying to break the three to four feet of rock that needed to be removed to accmmodate the new pipe. Mechanical trenching was considered but was proven to be overly expensive. On very short notice, Ireco of Florida was asked to design and execute a blasting procedure that would allow this project to proceed. Nearby buildings were over 80 years old, three of them containing antique shops specializing in glass antiquities with attorney offices above them. High water table compounded problem with a 20-year old steel water main and clay drainage pipe 15 feet frcan the new sewer line. Holes had to be drilled within six inches of the edge of the existing pipe to four feet below the pipe on either side of the pipe and blasted. No interruption in the sewer line flow was to be tolerated.

Jan 1, 1996

By W. Birch

The traditional concept of scaled-distance modelling for predicting blast induced ground vibration holds many drawbacks, not least of which is the major effect data scatter imparts on confidence determination. An investigation by the Department of Mining and Mineral Engineering, The University of Leeds, England has resulted in the development of simple but effective method of improving prediction capacity through the reduction of effective error by incorporating individual location response into a scaled-distance model. The work is the product of an l&month blast-monitoring campaign at a limestone quarry situated in North Yorkshire, England. The data, when presented in the form of a scaled-distance model, indicates a typical scenario where a good overall correlation becomes marred by the extent of data scatter. Examination of the individual monitoring locations however indicates that the response of the individual location is an important factor in the explanation of the large residuals. The novel approach thathas been developed incorporates a series of locational site factors which when incorporated into a scaled distance model reduces the effective error and therefore improves prediction capacity. The approach is based on using a standard computer package “spread sheet” on the understanding that these are commonly available on all quarry or home computers. This approach has been validated by comparison with a more rigorous statistics method.

Jan 1, 2001

By S C. Brashear, D A. Anderson, A P. Ritter, S R. Winzer, R Broughton

Results of quarry blasts can be quantified to show the effects of controlled variables. Two studies have been carried out: one to document the effect of delay on fragmentation and the other to show the effects of higher relief patterns and more accurate initiators. By using such techniques as highspeed photography and timing studies of mucking and crushing operations, subtle differences in blasting efficiency can be measured and quarry blasting can be optimized. Given the range of available and developing blasting technologies, quarry operators should resort to quantitative analyses of their blasting practices to get maximum productivity.

Jan 1, 1985

By John Turner, James Lamb

The Minnesota Department of Transportation (MNDOT) has an extensive project to improve driving conditions and reduce hazards to motorists on US Highway 61 between Duluth, MN, and Canada along the north shore of Lake Superior. In 1991, the Lafayette Bluff Tunnel was completed just north of Two Harbors, MN, through a joint venture of Johnson Brothers Corporation of Litchfield, MN, and Obayashi Corporation of San Francisco, CA.

Jan 1, 1994

By Ravi Sahu, Kris Jeremiah

This paper aims to study the benefits of using Post Processed Kinematics(PPK) surveying methodology combined with Drone photogrammetry to achieve highly precise positioning (X, Y, Z) of drill holes based on the drill pattern and to highlight innovative workflow of transmitting the drill plan to smart drills for accurate drilling.

Feb 1, 2020

By Dennis A. Clark, Richard E. Calvin

As the scarcity of mineral resources increase and subsurface mining activities expand along with simultaneous surface mining in coal, industrial minerals and rocks, along with metals, the need to insure safe conditions is paramount.

Jan 1, 1981

By Jorge Alvarez

In a large-scale open-pit mining operation, continuous efforts are made to control damage to the slope walls. An essential tool in this effort is determining the PPVc (critical peak particle velocity) in areas of interest. By knowing this value and generating criteria, drilling and blasting designs can be established to reduce vibrations that affect wall construction. It is crucial to understand that the PPVc changes as different mining phases develop, especially due to exploitation on the benches, which leads to vertical inherited damage. Therefore, it is imperative to regularly update the PPVc based on field tests that provide accurate data. With this information, vibration damage criteria can be established, and drilling and blasting techniques can be designed to minimize the impact on the remaining rock mass. This document presents a methodology for generating scaled criteria that best represent the reality of the rock mass.

Jan 21, 2025

By Alan Minchinton, Ian Kirby, Jim Chan

It has long been known that successful blasting in soft and hard rock can require the use of different explosives. While choosing an explosive of the right energy density is important, the dynamics associated with non-ideal detonation behaviour play an equally major role. Tuning the energy release rate of an explosive to optimise its blast efficiency can be likened to tuning an internal combustion engine to improve its performance.

Jan 1, 2014

By A. Gontijo, A. Matos, P. Lincoln, L. Fonsecail

This paper investigates how to manage and model the vibrations caused by rock blasting in a Brazilian underground mine. Considering the frequent detonations and the previous lack of effective vibration control, understanding, and reducing the impact of these seismic waves is critical. We emphasize the use of the near field model technique, which considers the varied physical properties of different rocks, optimizes blasting plans, and minimizes damage to the rock mass. We detail a case study that demonstrates a comprehensive approach to vibration control. The discussion includes the creation of a monitoring plan, the methodology used, results and the specific challenges and solutions found during the blasting process. This study provides a practical guide for similar future projects. Finally, we present a predictive model based on the collected data, offering insights into the vibrations caused by blasting. This model helps decision-makers minimize the risk of displacing rock blocks in the blasting area, improving safety and operational efficiency

Jan 1, 2024

By O E. Crenwelge

Seismograph measurements are usually made near blasting operations solely for the purpose of monitoring compliance with governmental regulations. However, recordings of seismograph signals have far greater potential than this, if the proper procedures are used for analyzing the transient data.

Jan 1, 1991

By N H. Maerz

The digital image analysis program WipFrag has been developed under contract to INCO for use in quality control of underground blasting operations. This paper outlines the relevance of fragmentation to underground mining, the hardware and photography requirements, and key features and operating principles of the software.

Jan 1, 1995

By Floyd W. Crump

New technology in video equipment, such as Super Video Tapes, Super Video Camera Recorders equipped with high speed electronic shutters, and VCR's with editing capabilities make it possible to resolve high speed events to still frames with an event elapsed time of 17 milliseconds (ms). This is far from the 2 ms resolution available with a High Speed 16 mm Film Camera such as the LOCAM at its maximum 500 frame persecond speed, but is adequate for many field blast evaluations.

Jan 1, 1991

By P. D. Katsabanish

Air decking applications are examined using numerical modelling and the AutodynTM code. The mechanism of damage is illustrated and discussed. Air decking is shown to provide advantages over stemming when powder factor is maintained. The current effort does not support reduction of the explosives column in favour of air decking. In a similar fashion, bottom hole air decking increases fracturing in the area of the air deck, compared to when the same volume is occupied by inert materials; however air decking does not appear to reduce the requirement for subdrilling. The apparent discrepancy between the numerical results and some field observations reported in the literature is discussed.

Jan 1, 2005

By Quian Liu

Since the establishment of the CANMET Experimental Mine in Val d'Or, Quebec in 1991, research activities in rock fragmentation have been carried out not only in the underground laboratory but also in production mines in the north-west Quebec region. Among the instruments available for rock fragmentation, the Kodak EktaPro 1000 Motion Analyzer (also called the high speed video system) has been one of the most useful tools for monitoring blasts in both underground and open pit. This system is capable of recording events at rates from 50 to 12,000 frames per second (fps). The buffer memory has a capacity of storing 2050 images. To use this system in the underground, a steel box was made with a bullet-proof glass in the front to protect the camera. The processing and recording equipment are placed in an aluminum case which can be located about 30 m away from the camera via an extension cable. For each blast monitored, high frequency geophones and accelerometers were used to monitor ground vibrations and give a timing reference of the explosive detonations to correlate with the observation of the captured images.

Jan 1, 1994

By Malcolm Mellor

Practical procedures that have been developed for pre-split blasting and smooth blasting in common rocks are reviewed systematically. Topics covered include shothole spacing, charge weight per unit length of shothole, decoupling ratio, adjustments for explosive type and rock type, and weight of explosive per unit face area. Relevant properties of frozen rocks, frozen soils, and ice are compared with those of common unfrozen rocks, and appropriate adjustment of blast design is discussed. Interim relationships for the design of controlled perimeter blasting in frozen soils and massive ice are put forward, recognizing that additional experimentation is required. Special problems in controlled blasting of ice are discussed. These include effects of wet holes, delayed removal of burden, and submerged burden. Special attention is given to the cutting of ice islands and icebergs. An Appendix describes an operation in which the face of an ice wharf at McMurdo Sound was trimmed by pre-split blasting.

Jan 1, 1976

By Philip M. E Thomas

For over sixty years man has struggled to defeat the natural swamp lands known as the Florida Everglades as demand for land to support the burgeoning population growth in the state continued almost unchecked. Over the past ten years there has been a growing awareness that this land development could wipe out a whole ecosystem in a very short time unless steps were taken to reverse the trends. In 1991, a state law called the Marjory Stoneman Douglas Everglades Protection Act was enacted giving power to the South Florida Water Management Board to condemn certain lands for conversion to manmade swamp lands, designed to filter polluting run-off water from the agricultural lands around Lake Ockeechobee.

Jan 1, 1994

By Ettore Contestabile, Cameron Thomas

Implosive-type electrical/mechanical connectors such as XECONEX have been used extensively for joining electrical transmission lines. This implosive action of explosives has also been applied to other forms of high energy metal working with excellent results. However, as with many other products, the inherent blast energy of these units has caused some environmental concerns especially when used in proximity to inhabited areas.

Jan 1, 1995

By Gary L. Self, Ronnie Daniel

With the advent of large scale blasts utilizing overburden casting techniques, it was imperative that an ultra reliable surface delay system be developed. Shock tube and detonating cord surface delay systems have been hampered by the lack of a reliable easy-touse method of incorporating multiple paths of initiation to each hole. Two new redundant nonelectric delay systems have been developed utilizing multiple signal paths to allow a higher degree of safety and reliability. The first system designed uses a combination of detonating cord and nonelectric shock tube delays to allow multiple delay paths to each hole. The second system incorporates a new all shock tube delay system which allows multiple delay paths while minimizing over-pressure by eliminating detonating cord trunk lines. These two redundant systems have been used in over 500 production blasts without any misfires due to surface cut-offs or detonator malfunctions.

Jan 1, 1989

By E. Contestabile, B von Roser

Schedule IV containers in Canada and IME- containers in the United States have made possible the transport of mixed loads. That is, using these containers for detonators, one can simultaneously transport detonators and explosives on the same vehicle. As a result of a recent accident, the Canadian Chief Inspector of Explosives asked for a review of the appropriateness of the Schedule IV container in its present use. The Canadian Authority asked for a re-assessment of the adequacy of the Schedule IV container in preventing propagation of a reaction from the detonators in the container to the remainder of the explosives on the truck, and its ability to contain fragments generated by the detonators. A series of tests was performed to determine the initiation threshold temperature for non-electric detonators and the failure threshold temperature for the shock tube to establish some guidelines for preventing communication from one case of detonators to another within the transport container at elevated temperature. Tests fell into the following categories: inter-case sympathetic detonation, detonator thermal auto-initiation, shock tube thermal sensitivity, and intra-case sympathetic detonation. The results indicate that temperature is a critical factor, which determines to what extent, if any, communication occurs.

Jan 1, 2002

By Mark Roberts

Automation, data analytics and optimisation are key trends in the mining industry. Doing more, and better, while expending less resources targets KPIs around efficiency and productivity. With the explosion of data, the next step is to develop an optimal level of processes and systems to harness this data to support value-in use decisions. Typically, significant amounts of resources and effort are invested to develop realistic simulation models. However, models are frequently not integrated with existing systems, and therefore are underutilised. When we consider the specialised process of blasting, integration with upstream and downstream processes is a significant driver to realise sustained improvements and value. The application of genetic algorithms and cloud computing to solving complex mining problems has advanced over the last 15 years, in particular with mine scheduling. Genetic algorithms are unique in that they support true multi-objective optimisation, utilising population-based methods to present trade-offs between multiple solutions. Secure in-cloud processing speeds up the processing, with results delivered in timeframes that are not feasible with desktop computing.

Feb 6, 2023