Search Documents

By C. Pelley, S. Kelebek, G. Kunzel, P. Katsabanis

Small blocks of granodiorite have been subjected to blast loads from a single borehole and from a series of boreholes detonating at various timing intervals. The damage of the blocks was assessed through P-wave velocity monitoring, measuring the change of the point load strength index of the rock after dividing the large blocks into smaller ones and measuring the work index of the material at different distances away from the blasthole. Numerical modelling with the AutodynTM code enabled visualization of damage. It was shown that damage is optimum at a small delay time between successive holes while it drops rather drastically after this point.

Jan 1, 2003

By P D. Katsabanis, W Roberts

Commercial explosives exhibit non ideal behaviour which is very difficult to model. The fume spectrum produced by commercial explosives apart from its practical significance for underground mining is of great theoretical importance since it reveals information about the chemistry of the detonation process. Emulsions, watergels and dynamites were tested under various degrees of confinement in an one cubic metre closed chamber. Sand, concrete, steel and copper pipes were used to alter confinement. The degree of confinement was found to significantly influence the quantity (litres/kg of explosive) and the relative proportions of toxic and non-toxic fumes (percent of total fume measured). These results lead to further confinement testing using various rock materials. Fume results, and thus detonation performance were found to be dependent on the type of rock material used for confinement. Materials such as dolomite, limestone, and granite were found to result in a relatively high detonation efficiency of the subject explosive as shown by the distribution of detonation fume products. Conversely materials such as sandstone, talc and massive sulphide resulted in fumes suggesting low relative detonation efficiency. Fumes appear to be a sensitive indicator of the completeness of reactions occurring within the expansion zone of the composite emulsion explosive, while the detonation velocity is relatively insensitive to small variations in confinement. Estimates of sonic velocities of the confining rock materials were found to show no correlation with VOD results. However good correlation between fume results and sonic velocity suggests that the performance of an explosive as indicated by the resulting fume spectrum is affected by the degree of confinement.

Jan 1, 1992

By Robert J. Nothnagle, Kristen Franz Begor, Rodney W. Sutch

Recovery of contaminated groundwater in a fractured bedrock system presents some unique problems. Typically, the most common problem occurs from the inability to adequately characterize the discrete fractures through which contaminants may be migrating. Without adequate characterization, difficulties arise in properly positioning recovery wells and verifying the performance of the system. To overcome these difficulties at a site in Upstate New York, an innovative approach was developed involving the creation of an artificial fracture zone through controlled blasting to intercept contaminated groundwater flow.

Jan 1, 1988

By Sam Taoum, Omar Riahi

Few tools allow for accurately tracking ore dilution after blasting. Existing methods often rely on data analysis or linear interpolation of velocity, which can be imprecise and less effective in varied geological settings. A promising alternative is the use of numerical simulations, which involve complex mathematical calculations incorporating real physical data about explosives and geological characteristics. These simulations can model blast-induced fragmentation and subsequent ore dilution with greater accuracy, providing detailed insights into blast dynamics by considering factors such as explosive type, blast pattern, and rock properties. Numerical simulations integrate data from sources like seismic sensors, blast monitoring equipment, and geological surveys, offering a holistic view that single-method approaches cannot match. By simulating different scenarios, mines can predict the outcomes of various blasting strategies, optimize blast designs to minimize ore dilution, and maximize recovery. Advanced numerical simulations enhance the prediction of fragmentation distribution and size post-blast, crucial for effective dilution control and maximizing ore recovery rates.

Jan 21, 2025

By Richard Arsenault

The production of oil & gas from wells requires method of flow from the producing formation into the well bore. Once the well is drilled it will have casing pipe installed to protect the integrity of the well formations and means of delivery to the surface. Once casing pipe is installed it will be cemented in by pumping cement through the annulus of the casing pipe down to the bottom of the well and allowed to flow outside the casing pipe up into the formation.

Jan 1, 2007

By Mike McGill, Stephen Chung, Dale S. Preece

Cast blasting can be designed to utilize explosive energy effectively and economically for coal mining operations to remove overburden material. The more overburden removed by explosives, the less blasted material there is left to be transported with mechanical equipment, such as draglines and trucks. In order to optimize the percentage of rock that is cast, a higher powder factor than normal is required plus an initiation technique designed to produce a much greater degree of horizontal muck movement. This is a significant change from normal blasting practice where fine fragmentation and sufficient muck movement were the prime requirements to permit efficient excavation.

Jan 1, 1994

By W. Boas, R. Silva, D. Yumi, L. Steffen

The continuity of the flow and stages within the mining process is essential to achieve success in its operation and results, especially when it comes to a gold mine. During the first seven months of 2022, crushing at the Morro do Ouro Mine had 19 stops in the primary crusher due to equipment blockage/obstruction, this could be due to the size of the material that was blasted with explosives and fed. The feeding of coarse material to the crushing plant impacts the operation in several ways, for example, premature wear of the equipment, reduction in the supply of the remainder of the beneficiation, reduction of the buffer pile and damage to the conveyed belt. In a mine located far from the community, the fragmentation improvement is mainly related to load increments or some other relatively simple change. However, when it comes to a mine located close to communities, alterations of this type must be analyzed in detail, as it can have an impact mainly in relation to vibration and flyrock. Aiming to improve the efficiency of the blasting, mainly in relation to the result of fragmentation, a project was created to improve the efficiency of the blasting with a focus on reducing the crushing stoppage and reducing the amount of material discarded due to inadequate granulometry. During the evolution of the project, several improvement solutions were proposed, for example adjustment of the power factor in relation to the geological characteristics of the rock mass, drainage, blasting geometry, vibration reduction techniques and several operational improvements. By using the techniques and methods identified as improvements during the project, it was possible to observe and quantify improvements in relation to the fragmentation of the blast. During the months of January to July 2022 there were 19 events. It was estimated that at this rate there would be 14 more blockage events, but there were only 3 events and that meant a 79% reduction in blockage. In addition to the reduction in crushing shutdown events, there was also a 53% reduction in the amount of ore that is discarded due to inadequate granulometry and, with that, the feed rate of the grinding system was able to reach the maximum feed limit due to the material being fed to the mill well fragmented, contributing to increase the production and productivity of the beneficiation process at the Morro do Ouro Mine in Paracatu-Minas Gerais-Brazil.

Jan 1, 2024

By E. McCullough, D. Preece, M. Ortel

The mining and oil industries employ techniques such as geologic mapping, core drilling and electromagnetic field techniques to explore for new deposits. New discoveries of major near-surface ore bodies are becoming progressively rare and traditional exploration methods are unable to resolve ore bodies deeper than about 500 m (1640.4 ft). Consequently high-resolution seismic reflection techniques show great potential for exploration to much greater depths down to almost 3 km (1.9 mi).

Jan 1, 2013

The use of angled shot holes can be extremely effective in blasting faces that either have a great deal of toe burden or where it is difficult to give a drill access to a face due to backbreak and face erosion. However many quarry operators are wary of using angled holes because of the perceived possibility of increased flyrock and uncertainty of the driller's abilities to drill at the designed angle.

Jan 1, 1994

By Philip Barnhard, Lyman G. Bahr

By recording the arrival time of a pipe wall at evenly spaced intervals in a plane perpendicular to the pipe axis, application of the equations of motion permits calculation of the pressure of the explosive acting to accelerate the pipe wall. Data observed from various non-ideal explosives are presented, together with values of pressure to be expected from thermodynamic calculations.

Jan 1, 1981

By B Mohanty

Several parameters such as, Energy, Strength, Brisance, Impulse, and Bubble Energy, are in common use in the explosives industry today to rate commercial explosives in terms of blasting performance. However, this multiplicity of terms, their frequent interchange and their purported one-to-one correlation with expected performance have given rise to a considerable amount of confusion, and have often resulted in unrealistic rating of explosives. In this paper, various theoretical and experimental methods of estimating energy and performance of explosives are discussed and their relative merits examined. These methods include, Computer Code Calculations, Cylinder Test, Trauzl Test, Ballistic Mortar Test, Underwater Test and Model-scale blasting. It is shown, in the light of actual blasting process, that such measures cannot be considered accurate indicators of expected blasting performance as the properties of rock to be blasted are either totally ignored or only partially accounted for in these methods. It is also shown that no single technique alone among those currently employed by the explosives industry can lead to realistic rating of explosives in terms of expected blast results. The need for the adoption of a two-tier rating system, one based on chemical potential "energy", and the other based on blasting "performance" is proposed, and specific approaches to achieve this objective are outlined.

Jan 1, 1981

By Tom Burleson

High-speed photography has proven to be an extremely valuable tool for the evaluation of blasting practices in the Warrior Coal Basin. A research project, coordinated by Nelson Brothers Inc. and The University of Alabama's Mineral Engineering Department, has centered on the use of high-speed photography to study and analyze blast performance. A large number of production shots in this region has been filmed and studied. The data obtained from the films have been used to establish graphical relationships between certain blast parameters and overall shot performance. These relationships will be used to develop a computer model that will estimate cast results from a given burden explosive energy combination. This paper describes the methods and procedures used to develop these relationships. The results of the research are discussed along with plans for continuing the research project.

Jan 1, 1988

By Ray Heater, Qian Liu, Alan Bauer

The channel effect is a phenomenon that takes place with decoupling explosive charges; an air shock wave propagating ahead of the detonation wave in the annular space around the explosive charge compresses the charge so that the process of detonation is modified and even stopped. For commercial explosives, such as AN/FO slurries and emulsions, the channel effect causes partial detonation under certain conditions. To simulate and evaluate the phenomenon, a hydrodynamic model was developed based on the assumption that the pre-shock wave is produced by Mach reflection at the tube walls. Based on instrumented experimental studies with the above explosives in diameters ranging from 25 to 90 mm in pipe sizes ranging from 35 to 127 mm, it has been possible to demonstrate that a criterion for failure based on a critical impulse concept fits the experimental data well. Critical impulse values for the various explosives tested are presented along with the necessary correlations between charge and borehole diameter required to produce this.

Jan 1, 1988

By Neil E. Gehrig

The word "slurry" was used by Dr. Melvin Cook and Mr. Henry Farnam to describe a new blasting agent developed in 1956. This development, along with the development of ANFO triggered the Modern Era of Blasting. We have seen the results, a massive expansion in the commercial explosives industry. Someone once said, "You can't know where you're going if you don't know where you've been." With that in mind, this paper deals to some extent with the origin and development of slurry explosives and then with their future high potential.

Jan 1, 1982

By Tim A. Beattie, John R. Grant, David L. Kennedy

After many years of research, ICI staff have developed a numerical modelling system for the study of detonator/primer/explosive configurations. Results from this work clearly identified that current primer designs were not as effective in delivering their energy potential as needed. Alternative designs were evaluated and several prototypes, all essentially spherical in shape, were built for testing. Results have shown a significant improvement in various aspects of primer performance, including omni-directional pressure transferral and increased energy release rates. Reliable, high performance priming of explosives is now achievable for a much wider application range.

Jan 1, 1991

By J Mensah, G C. Sen

Often large boulders of rock have to be fragmented in civil or mining engineering operations. These oversize boulders are encountered after primary blasts in both surface and underground excavations of minerals. Various methods are employed to break large boulders into a manageable size for loading and crushing. These methods range from mechanical breaking (such as drop-ball and hydraulic impactor) to the use of explosives. Apart from these, static agents (such as expanding chemicals) are used in special circumstances.

Jan 1, 1989

By R W. Bellenie, P N. Blakey

The phenomena of post detonation gases in muckpiles is reasonably well known. It causes the 'rumbling' noises occasionally heard after a blast in open pits or quarries and is thought to occur due to initiation of carbon monoxide, hydrogen, etc. by 'hot' spots within the muckpile. The problem usually occurs with highly aluminized products, but can occur with any oxygen deficient product. This phenomenon was never a problem underground due to restriction on access to blast areas, ventilation criteria, etc. until the advent of large diameter blastholes and particularly their use for specialized applications such as drilling for blasting down 'hang-ups' in ore passes.

Jan 1, 1980

By L D. Lawrence, R S. Day, Gordon Coleman

Commercial emulsion explosives are typically characterized by their relatively high detonation velocities due to the intimacy of oxidizer and fuel and to their sensitization with glass microballoons. However, numerous blasting operations in softer, more porous rock formations are better fragmented with slower shooting explosives. Although mixtures of emulsions with large amounts of ANFO (60-80%) can considerably reduce the high velocities, little water resistance is achieved with low levels of emulsion blended with ANFO. "Water proof" blends containing typically 50 percent of emulsion become quite costly due to escalating powder factors in ANFO patterns. Blends of sensitized emulsions with 20-30 percent ANFO retain the high velocity characteristics of the emulsions as well as increased densities which can also adversely affect blasting results in softer rock formations. The introduction of a reliable and predictable on-site gassing process for sensitization and density control of repumpable emulsions, with or without added ANFO, offers the end user the option of supplying a final product more suited to his blasting needs. The capability to widely vary final product loading densities and consequently product detonation rates better tailors the final explosive to different rock characteristics. The beneficial advantages of this system in softer rock formations have been well documented. Overall comparison between these variable density products with typical repump emulsions containing solid density control will be reviewed. Besides the obvious cost advantages and safety advantages of these systems the end user is provided more definitive control of his blasting operation.

Jan 1, 1990

By Roy Rose, Bruce Bowles, Wesley L. Bender

Numerous large diameter water wells are used to dewater the pit at the Sleeper Mine. Occasionally, a well will be located inside the boundaries of a blast. Although one might expect that wells so located would become inoperable due to blast-induced damage, in most instances this has not proven to be the case.

Jan 1, 1991

By D T. Froedge

To preface these remarks, it is not intended that this paper be a criticism of anyone or any organization involved in drafting the current regulations, for it appears that everyone involved in the process has made an extreme effort to be safe. We wish to show that in this case by making huge safety margins, we have created an unsafe condition in another area. That is by creating vast safety margins in the area of mobile transmitter intensity versus distance scales we have caused a severe handicap in the use of the mobile transmitter in securing blasting areas. The use of these mobile transmitters, which are absolutely essential in clearing areas where there are woods, mountains, or urban structures is virtually eliminated because of the safety factors prescribed in the regulations. We wish to show that these mobile transmitter safety factors are much too great, and can be traded off to increase the margin of safety in the ability to clear blasting areas.

Jan 1, 1975