Search Documents

By Mark S. Stagg, Stephen A. Rholl

The Bureau of Mines is studying blast delay timing influences on rock fragmentation in a series of tests that started in 3-ft concrete blocks, progressed to 45in-bench reduced-scale tests in massive dolomite, and has now included 22-ft-bench full-scale tests in a thin-to-thick horizontally bedded dolomite. This paper discusses the full-scale test results and how they compared to the concrete block and reduced-scale studies.

Jan 1, 1988

By Ken Fiorentino, Gordon F. Revey

H3 Tunnelers recently excavated two conventional 48 foot diameter highway tunnels through the Halawa side of the Tran-Koolau Mountains on Oahu. The primary blast design challenge on this Job was minimizing overbreak In the alternating layers of pahoehoe and aa lava, clinker, end tuff. Two different excavation techniques were evaluated in the Halawa tunnels. The first method used drilling and blasting to excavate the tunnels to within one foot of their final perimeter. A roadheader, mounted on a backhoe, was then used to excavate the remaining foot of ground. The second method used conventional smoothwall blasting techniques, without any mechanical excavation. This paper describes the details and relative success of the two excavation methods tried in the Halawa tunnels.

Jan 1, 1993

By Paul Worsey

A strong inverse relationship between rock face movement and stemming ejection is presented. Previously unpublished data from blast control plug research and development involving high speed video analysis, which was conducted between 1986 and 1988, is presented. Face and stemming ejection velocities were calculated for tests utilizing the same bench blasting configuration comprising; a 4 ft high bench in dolomite, 3 ft burden and single 1.75 in. holes loaded with 2 ft of small diameter cartridge emulsion. The singular difference between these tests was the stemming configuration. Varying lengths of stemming were used with the presence or absence of differing experimental configurations of blast control plug. The effectiveness of this plug has been published previously.

Jan 1, 1990

By Mike Koehler

An underground mine that produces aggregate limestone was in operation for approximately eight years when geological changes resulted in dangerous rock falls. The roof in the mine was not bolted; therefore, the drilling and blasting program was called upon to maintain roof integrity. Drilling and blasting were analyzed and modifications were adopted to stabilize the roof. Initial changes were made in the drilling equipment, drill pattern, explosive type, and timing. Any amendments made, after the initial phase, were made individually so it would be easy to discern which changes worked.

Jan 1, 2002

By Fumihiko Sumiya, Koichi Kurokawa, Yukio Kato, Tetsuya Sawada

In some metal mines, it is a serious problem the decomposition of explosives which occurs suddenly by contact with ore containing pyrites under high temperature conditions. In the present paper, we investigated heat resistant properties of emulsion explosives and other industrial explosives by contact with ore containing pyrites under high temperature conditions.

Jan 1, 1992

By Virgil J. Stachura, Larry R. Fletcher, Matthew N. Plis

Falls of ground remain a leading cause of fatalities and injuries in underground mines. In response to this situation, the Bureau of Mines conducted a series of experiments in the White Pine room-and-pillar copper mine which resulted in smoother, safer ribs due to a reduction in the amount of overbreak caused by blasting. The tests evaluated the effects of changes in the loading of the rib holes of the mine's 20- by 28-ft drift round driven in shale and sandstone. The relative integrity of the ribs remaining after the blasts was measured using both photographic and seismic refraction techniques.

Jan 1, 1989

By Michael D. McGill, John L. Turner, Don Sieger, Doyle Newhouse

Since its introduction by Atlas Powder Company in late 1986 as a means of highwall stabilization in surface coal mines (1), applications of the basic AirDek (2) blasting technique have multiplied rapidly.

Jan 1, 1991

By Walt Meglasson

"Developing technologies in demolition equipment and processes have produced a newsophistication within the demolition industry. Yet, with increasing frequency, owners,architects, engineers, and contractors reject out of hand one of the safest and most effectivetools in the demolition industry today, specifically the use of explosives and blastingtechniques in man_made structure removal. The use of explosives in any application mustbe considered as a tool, no more or less dangerous than any other type of tool, when usedproperly. Accordingly, importance must be attached to recognizing the skill, integrity, andcare of those who use it. Massive amounts of information and help are available to assistthe rock blaster, ranging from the practical to the highly theoretical, but very littleinformation exists to guide anyone considering unleashing the power of explosives instructural demolition blasting. The planning and work required to execute such projects iscomplex, and the recognition of the different applications explosives can be applied to isthe first step."

Jan 1, 1993

By Jennifer P. Harrell, D. Joseph Hagerty

In many areas of the eastern United States, especially in the Midwest, past mining activities have left large and extensive underground openings. Now, renewed mining is occurring in such areas in surface pits. Also, construction blasting often occurs in rock over such old openings. Within the last fifteen years, some attention has been given to the interaction between surface blasting and underground cavities; concern has been expressed about the possible changes in vibrations transmitted through areas underlain by old mine workings (Siskind, Stachura and Nutting 1987). Previous studies also had indicated that underground openings could influence transmission of surface mine blast vibrations (see, for example, Woodward-Clyde Consultants 1977). The principal concern is that underground openings under surface blasting may intensify low-frequency vibrations. If such intensification occurs, use of available equations to predict peak particle velocities and to design blasting patterns and select blasting parameters could lead to possibly damaging ground shaking.

Jan 1, 2002

By H Russell

An account of an experimental blast at the Sullivan Mine involving a small pillar drilled with 4 1/2" diameter up-holes, and loaded with emulsion explosives from a truck-mounted tank/pump unit.

Jan 1, 1984

By Zhou Jiahan Wang Feng

This paper introduces the mechanism and the operating process of dike building by silt squeezing blasting. DBSSB (dike building by silt squeezing blasting) has the following advantages: shorter construction period (the construction period is decided only by the speed of rock materials filling)greater consolidation of the body of the dike, more structural stability, smaller settlement. Therefore by conventional standards the same dike can be designed with a smaller cross section than other construction methods, and at a reduced cost when enough rock materials can be provided in site.

Jan 1, 2006

By D Schneider, H Elliott

The advantages and disadvantages of using inclined boreholes in blasting has been under discussion for a long time. Some recognized disadvantages are that drilling costs, both operating and capital costs, are higher for inclined holes than for vertical ones, and that drilling accuracy is more difficult to maintain. People who have used angled holes in practice, on the other hand, have claimed that the quality of blast results was improved. In fact, their popularity has increased, especially in Australia.

Jan 1, 1988

By Shijie Qu, Paul N. Worsey

Pre-splitting has become widely adopted for the formation and protection of final surface rock excavation profiles in both large scale civil construction and highway rock cuts. Jointing has been shown to affect the success of pre-splitting and the smoothness of the resulting profile, however, only closed joints have been investigated. Frequently jointing that is closed at depth is open at and near the surface due to weathering, reduced stresses and ground water percolation. In many instances, problems are associated with surface rock layers whereas at depth these problems are either reduced or do not exist.

Jan 1, 1987

By Gungor Tuncer, Erhan Bakirci, Ali Kahriman, Atilla Ozmen, O. Nuri Ucan, Savas Gorgun

There are several methods for demolition of structures but most of them depend mostly on conventional ways of using machines for breaking and crushing structural elements. However the need for lots of work force, expense and extreme amount of time for demolition, made most of these methods non-popular nowadays. Therefore, trials to accomplish a more economic and less time taking method lasted with the use of blasting. By applying controlled blasting on a suitable structure, the structure can collapse and break down to pieces in very short period of time, with no extra work force and cost. In spite of advantages of explosive demolition, the potential danger of explosives and the damage that the blasting may cause to surrondings, if not controlled properly, made people timid to the method especially in urban areas. Therefore, the pre-assumption by computational analysis has become an essential matter in the process.

Jan 1, 2002

By Rhys Baker, Tim O’Brien, Joshua M. Hoffman

This paper discusses this division of power as it relates to the explosives industry. Each branch is responsive to the public and the processes through which each promulgates regulation and legislation require public input in different forms.

Feb 1, 2020

By R W. Givens

This paper discusses emulsion performance and characteristics. Also presented are pattern design equations by a weight strength method, a "Q" factor method, and a coupled energy powder factor (CEPF) method. Pattern expansion by replacing ANFO with emulsion is presented along with quality control checks for emulsion products. The predicted performance of the calculated burden and the equivalent powder factor as a function of the emulsion percentage, as determined by the three methods, is compared. Field results indicate that of the three methods the weight strength is the moot conservative, the "Q" is overly optimistic, and the CEPF more accurately predicts the effect of coupling and is more consistent with a variety of emulsion and heavy ANFO products.

Jan 1, 1989

By D K. Joyce, B Mohanty

"A variety of initiation modes are currently in use. This includes initiation by single ormultiple detonators and boosters, by detonating cords of varying strengths, and bycombinations of cords and boosters. A lack of clear understanding of the role of initiationon detonation characteristics often leads to under-utilization of the explosives system inblasting. This paper reviews the current practice of initiation in packaged and bulkexplosive products. It illustrates the effect of various types of initiation on energy releasecharacteristics in emulsion and ANFO, through calibrated underwater energy tests. Itcompares energy release under end-inidadon against side-inidadon condition for variousinitiator strengths. The effect of confinement on these characteristics has also beeninvestigated. It is shown that side-initiadon by detonating cord results, in most cases, insignificant degradation of detonation properties. This study also provides guidelines forselecting the optimum mode of initiation for various blasting situations."

Jan 1, 1993

By Leslie Taylor, R. Reed Skagga, William Gault

The ultimate aim of our overall task, of which the effort described in this paper is a part, is to be able to model the impulsive output of buried charges and the response of targets of interest. It is not practical or cost-effective to determine the response of all targets of interest to buried charges of all sizes by testing them. In order to have confidence in our models, however, they must be validated by a modest number of tests. A critical element in modeling the response of a target is the ability to model the loading function. The load a buried charge applies to a target above it when the charge detonates can be characterized in terms of the vertical impulse. The vertical impulse is a function of the size of the charge, its depth of burial, and the properties of the soil in which it is buried. The primary objective of the effort described in this paper is to determine the load a known charge places on a non-responding target so the data can be used to validate our models.

Jan 1, 2005

By Norman S. Smith, Richard L. Ash

Many factors affect rock fragmentation from blasting. One variable seldom considered when designing blasts, however, is the borehole length. An example is described of how the length was adjusted to give better breakage when using 4-inch diameter blastholes at a quarry. To explain the basic principles involved test results from experiments conducted by the authors where borehole lengths were altered are presented and evaluated.

Jan 1, 1976

By Huang Fenglei, Jin Qiankun

A new linear charge method has been applied in coyote blasting for highway excavation in which presplitting boreholes are set along the designed rock slope with some empty chambers at the end of linear charges whose axes are perpendicular to the axis of the highway. Three-dimensional nonlinear finite element analysis for this method has been conducted using LS-DYNA3D. The results indicate that the blasting damage to the rock slope is reduced greatly using the new linear charge method in coyote blasting.

Jan 1, 1998