Search Documents

By N. Skopak, C. Aimone-Martin, J. Redyke, B. O. Meins

PipeBlast is a spreadsheet-based calculator based on research conducted by Southwest Research Institute (SwRI), used by the pipeline industry to determine if proposed blasting planned near existing pipelines can be safely executed. The two factors determining “safe” are blast-induced pipe wall hoop stresses and predicted peak particle velocity (PPV) at the pipeline. Although methodology used to predict hoop stresses is somewhat sound, predicted PPV amplitudes are highly exaggerated based on inappropriate attenuation models developed using spherical explosive charges of limited charge weights, placed in soil adjacent to model pipelines that do not represent rock blasting. Hence, pipeline companies readily reject well-design blasts and limit scaled distances far beyond what is reasonable and cost-effective to pipeline owners. Full-scale trench blasting in rock was conducted near a 24in (711mm) diameter operating API 5L X70 grade steel pipeline in Texas to compare PipeBlast model predictions with a Ground Strain Model (GSM) based on field measurements of ground motions on the surface and at the pipeline springline. Results of the GSM were compared with pipeline strains measured using wire gauges mounted on the Springline. The comparative results showed that a site-specific velocity propagation model provided good estimates of ground strains that are replicated on the pipeline walls in terms of hoop and longitudinal strains. Trench blasting 28ft (8.5m) from the pipeline produced ground motions of 7.6in/s (193mm/s). At this ground motion amplitude, the factor of safety defined as the allowable stress divided by the combined operating and blasting hoop stresses was reduce from 3.04 in the absence of blasting to 2.98. This paper explains the research and findings on which PipeBlast is based and presents an alternative approach to predicting blast-induced pipe wall stresses based on site-specific velocity propagation measurements and a ground strain model.

Jan 1, 2024

By Guillermo Lazcano Ríos, Jorge Parvez Aguirre, Alejandro G. Díaz Berríos, Felipe Rodriguez Alveal

Codelco's Chuquicamata Underground Division (DCHS) faces issues due to collapses in its subsidence streets, which hinders the advancement of the subsidence front and leads to the loss of areas and reserves. To address these issues, DCHS and Orica have developed a new excavation methodology based on pre-loading explosives in high drawbell. This methodology involves creating a high drawbell extending from the floor of the production level to the ceiling of the subsidence level, divided into two phases: upper and lower. A resin stemming is used to separate these phases. The excavation strategy adjusts to variables such as reception volume, fluffing, and excavation geometry, involving vertical pre-loading of the explosive and the use of a separating element between the phases. The test aims to validate the new excavation methodology and the retaining element in the rock mass, evaluating aspects such as drawbell geometry, impact on the rock mass, damage to the retaining element, and fragmentation. Wireless electronic detonators are used in the upper phase to improve safety by eliminating the need for physical connections, while traditional electronic detonators are employed in the lower phase. Low-density bulk emulsion is applied to minimize the impact on the Crown pillar and extraction point, and higher-density explosives are used above the subsidence level to ensure good caving. Results showed that the blast achieved 86% conformity with the theoretical design. Resin stemming allowed for 100% effective detonation in the upper columns, and the fragmentation obtained was 5.44 inches, which was less than expected. No damage to the Crown pillar was observed, and the explosive quality met standards. This technique has proven to be effective and viable, suggesting the possibility of eliminating the subsidence level in future levels, resulting in savings, and providing greater stability to the rock mass.

Jan 21, 2025

By Joshua Hoffman

The recruitment and retention of future talent into the explosives industry is becoming increasingly important. Student chapters help with this effort but what are they doing and are there things they could learn from each other? This paper discusses the University of Kentucky Student Chapter's efforts to grow membership, retain its recruits, and integrate them into the explosives industry. Several social and professional events during which the students are able to meet and network with members of their future industry are introduced. The special relationship that has been fostered between the University of Kentucky and Missouri University of Science and Technology is discussed. Professional development initiatives which are critical for a student to become vested in the industry are shared in this paper. These opportunities which range from internships to research positions allow a person to get a better understanding of the explosives industry and find the niche that best suits them. Many of the student chapters are closely connected with engineering programs. While this makes sense and both entities benefit from these arrangements there is a trend of job placement primarily in the engineering industry. By providing these students with the chance to learn more about the explosives industry and get hands on experience more of these future engineers and professionals can be retained after their graduation.

Jan 1, 2013

By TH Kleine, AR Cameron

Size assessment of fragmentation is all about estimating the population of fragment sizes in the rock pile. A knowledge of the size distribution of particles can be used in applications from evaluating the stability of a waste dump, to optimizing a blast design to achieve a required fragmentation, to on-line control of a crushing and sieving operation.

Jan 1, 1997

By Thomas M. Keevin, Gregory L. Hempen, David J. Schaeffer

In an attempt to reduce the potential for fish mortality during the explosive demolition of Locks and Dam 26, Mississippi River, the U.S. Army Corps of Engineers, St. Louis District explored the use of a bubble curtain to reduce the fish kill radius of underwater explosions. Bubble curtains are walls of bubbles rising from a bottom-resting bubbler manifold supplied with compressed air. Demolition engineers have long been aware of the attenuating properties of air bubbles in water. As such, air curtains have been routinely used to protect underwater structures from damage by underwater explosive shock waves. However, their use in protecting aquatic resources during full-scale explosive demolition projects was untested.

Jan 1, 1997

By Laurence Neufville

Proper risk assessment and blast design are very desirable to the execution of a blast. Not only will this ensure that it achieves its desired outcome, but the probability of complaints and litigation will be reduced. Blasting engineers rely heavily on site-specific data for analysis and input to the blast design equations, and therefore data collection is critical to this process. The traditional approach to data collection is to carry out site-specific reconnaissance by visiting the site, but the time spent doing so can be reduced if a remote sensing approached is adopted.

Jan 1, 2009

By Paul Sairato, Cathrine E. Johnson

Recruiting and retaining students in the explosives industry is becoming increasingly important each year. With no undergraduate degree in explosives engineering currently available in the United States, it is from other industries and degree disciplines we must recruit. The 2014 annual ISEE conference saw the first anonymous online survey distributed to members of SEE student chapters of the International Society of Explosives Engineers. The survey contained questions about future job and career plans, ideal job placement, expectations of salary and current academic degrees. The purpose of the survey was to determine what these students expect or require from a career in the explosives industry, and their current path to pursue this. This information can help steer recruitment activities and job offers for graduating students. The success for both student response rates and interest from the industry has allowed space for a yearly update of this survey. This paper provides the data from a second, restructured, online survey distributed to all student members of the International Society of Explosives Engineers, globally. Understanding the main incentives for a student to accept a graduate position as an explosives engineer can help us, as an industry; position ourselves to remain competitive in recruiting against other major degree disciplines.

Jan 1, 2015

By J. Aravena, S. Gajardo, M. Ayala, P. Salinas

Both, Teck Carmen de Andacollo (Teck CDA) and Orica, work hard in the implementation of new technologies available in the explosives industry and drilling and blasting techniques, with the objective of sustainable development of their operations, regeneration, and protection of the environment, also considering the welfare and relationship with the surrounding communities. The open-pit Carmen de Andacollo mine is located adjacent to the town of Andacollo. Therefore, both companies together have developed the implementation of different techniques and technologies to mitigate the impacts of mining operations in the community, considering an important part of this challenge to minimize the impact of their perception of blasting by reducing the level of vibrations and sound pressure (airblast), in addition to the control of dust and smoke, strengthening sustainable production in harmony with communities. The technologies and techniques that have been implemented are the installation of airblast and vibration monitoring stations stands out, whose database has records since 2011. Using the vibration database, different models were developed to predict the vibration level of blasting in its design phase, achieving a difference of 4.1% between the estimated and measured values in the last year. Two techniques stand out to minimize the ejection of material, "Hydraulic Dome" and "Dual layer blasting", the first consists of water irrigation on the surface to be blasted and the second is an unconventional blasting technique, which was awarded in 2015 for its results in the environment. Also pre-splitting engineering has been modified in a positive evolution, where through different configurations, the airblast has been reduced by 15% compared with records from 2011 to 2022. Finally, due to the impact of operational restrictions, such as days available to blast, number of holes, and powder factors, the wireless initiation technology was implemented, which allowed reducing the limitations in the loading, generating an improvement in terms of blasted materials over conventional systems. Understanding the restrictions and challenges in terms of impact on communities, the correct implementation of all these techniques is important, and in conjunction with collaborative work, it has been shown and validated that producing in a sustainable and sustainable manner is possible.

Jan 1, 2024

By Daodu Opeyemi

This paper describes several damages of blasting operations on some case studies, analyzes causative factors, and emphasizes preventive measures. Due to several complaints from some host mining communities as a result of blasting operations; two quarries from Nigeria suburbs were visited for study. The blasting design parameters in the mining companies were examined. Also, the history and existing conclusion of the neighboring buildings were studied using structured questionnaire, personal contact and visual examination. From the study carried out, it was discovered that varying negative environmental and socio economic problems resulted from the effects of vibration and flyrock on the nearby agro mining communities. The consequences are not limited to distortion of landscape but also include extinction of some animals, poor agricultural productivity; such as damages to economic trees and reduction in the yield of crops, health problems as a result of shock resulting to psychological disturbances, communal conflicts, blast induced cracks of structures and sometimes total collapse of host agro mining buildings, thus indicating that most mines did not comply with the safety concept of the existing environmental laws and regulations. Based on the results of the study it was recommended that proper blast design of quarries/mines should be conducted and the compulsory use of seismograph will be crucial in developing predictions. Environmental impact assessment should always be conducted before, during and after each blasting operation. Other possible control of vibration, flyrock and airblast, are also discussed in the paper

Jan 1, 2009

By Rakesh Raghavaraju, Bibhu Mohanty

Prediction of fracture and fragmentation characteristics of a rock mass subjected to dynamic loads, such as in blasting remains a major technical challenge. The present study is aimed at characterizing the shock transmission properties in controlled experiments in small scale in a well-characterized granitic rock, under varying borehole coupling conditions. Single blast-hole tests were conducted in a granitic rock sample of 145 mm (5.7 inches) diameter and height. The boreholes (in two diameters: 6.4 mm (1/4 inch) or 9.5 mm (3/8 inch)) were loaded with detonating cord of varying charge weight (5.3 g/m or 25 grains/ft to 31.8 g/m or 150 grains/ft of PETN). The effect of explosion gas penetration into the target rock was eliminated by inserting a thin-walled copper liner along the borehole wall. Embedded carbon composite resisters were employed at varying distances from the borehole to measure transmitted shock pressure for two coupling conditions (i.e. air and water) at distances of 1x to 9x the borehole diameter. The paper analyzes the decay of shock pressure as a function of distance from the borehole, and its implication on shock-induced fracture properties of the target rock as the first step in predicting fracture and fragmentation behaviour in a well-characterized rock.

By F Ouchterlony

Soviet precursors to Cunningham’s Kuz-Ram model from 1983 are described. They are rooted in the mean fragment size and Rosin-Rammler (RR) fits to sieving data and rely on approximations. Three versions of Kuz-Ram model are presented and all three are de facto based on the median fragment size x50, even if the term mean is used in the papers. This discrepancy caused Spathis in 2004 to suggest a correction procedure for the Kuz-Ram rock factor A, which was said to explain some of the missing fines in the model. This correction, while applicable to Cunningham’s 1983 paper, does not apply to his 1987 paper in which he presents his own A factor. Common fixes of the Kuz-Ram model’s fines issue are fragmentation models where the fines are mainly generated in a crushed zone around a blast hole. This is contradicted by careful model blasting tests. The lack of a largest block size in the RR function may lead to spurious values of the uniformity coefficient n, e.g. in conjunction with image based fragmentation measurements or crusher modeling. These issues may be solved by using the transformed RR function, which has a largest block size xmax or its replacement by the Swebrec function such as in the KCO model.

Jan 1, 2016

By Tom Snyder, John Brulia

PART 3 – UN Identifi cation Markings for the Highway Transportation in Commerce of Bulk Explosives, Oxidizers, and Combustible Liquids

Jan 1, 2015

By Felipe França Sitonio

Parameter’s control of explosives used in blasting operations have become more relevant over the years, bringing a better understanding of detonation performance. Giving into consideration that bulk emulsion density’s variation reflects directly on blasting results due to its importance in product sensitivity and velocity of detonation (VOD), blast designs are conducted assuming that cup density measurements are reliable and explosives gassing agents will perform as per specifications. Nevertheless, confinement conditions in boreholes like temperature, presence of water and surrounding circumstances of rock mass are often neglected on predictive modelling and off-site measurements. This paper describes the assembly of a device equipped with pressure sensors and its utilization in confined boreholes of an open pit mining operation, aiming to obtain in situ monitoring of density variation in several explosive columns. After we developed a software to get and process data of a hardware prototype and the device functionality was validated in water, oil and quarry mining experimental trials, 7 of 291 boreholes in a gold mine operation were chosen to be monitored with two probes each, placed at the top and at the bottom of the explosive column profile. The results obtained enabled a comparison between the bulk emulsion density variation when acting in different environments, since we selected boreholes with diameter of 101.6 mm (4 in) and 139.7 mm (5.5 in) and some with presence of water. Besides the increase of explosive density with depth related to hydrostatic pressure increase, we found an overall error of 6% in cup density measurements when compared with sensors placed at the bottom of boreholes and 2% when compared with sensors placed at the top of explosive column. These findings provide detailed insights into how bulk emulsion explosives behave in different circumstances including depth and borehole diameter, giving the opportunity to re-evaluate blast design parameters such as its geometry, sequence pattern, charging profile and explosive composition.

Feb 2, 2020

By Robert Hopler

BH Note: This price list stresses the point that the number six strength cap should be used with all high explosives. It’s interesting that duPont chose to continue to supply the lesser strength caps – but lowered the price of the #5 or #6 to be closer to that of the #4 and #3. There were imports of the lower strength caps at the time that had to be competed against, hence the price reductions. Another interesting point on this price list is the noting on the “Red Cross Explosives” page that these explosives reduce the danger incurred during the operation of thawing. As noted many times in these articles, this problem was not to be solved for about another 16 years or so.

Jan 1, 2011

By Lance McAnnuff

Whatever system is devised to control noise and ground vibration from blasting operations must present an effective compromise between the rights of the individual to be undisturbed by the actions of others, and the necessity for society, the whole of the population individually and collectively, to have the services and the products of commerce, industry and transportation along with the relaxation of recreational and cultural pursuits, all at a price within the means of the same society. One of the first jurisdictions in North America to attempt to quantify acceptable environmental limits for specific blasting operations was Ontario, Canada’s largest and most populous province. A process for development of guidelines applicable only to quarries and strip-mining operations was begun in 1974 and culminated with their inclusion in a “Model By-Law” published by the Ontario Ministry of the Environment in August 1978. This paper examines the process of development of the final guideline document and its application over the last 25 years. While acknowledging that the published guidelines for air blast and ground vibration control have provided a useful and generally workable framework for the purposes of land use planning and complaint or damage claim reduction, a number of flaws, weaknesses and misinterpretations connected with their application are identified. Recommendations for amendment of the controversial items are submitted with a view to making these and potentially similar guidelines in other jurisdictions, more acceptable to both government and industry.

Jan 1, 2004

By Alan Tordoir, Mark Roberts

The drill and blast process is a critical function within the production cycle which significantly impacts the ability of an operation to effectively meet its safety and production targets. Acknowledging that D&B design and reconciliation practices were conducted inconsistently across operations, a Group wide initiative was launched to embed a standardized design and reconciliation platform in line with the company’s Operating Model principles. A technical system was selected to deliver the digitalization of critical D&B information and enable ‘analyze and improve’ routines for design compliance monitoring and downstream productivity optimization.

Jan 1, 2019

By Robert B. Hopler

"The story of packaged explosives begins with the use of black powder (also called gunpowder) in mining. Although discovered in the 13th century, it was not until 1627 that the first records of use in mining is recorded. It took until the early 1800's before its use began in underground coal. Althougha free-running, granular material, its recommended (and safest) manner of use was for the miner to pour it into ready-made or onsite formed paper bags prior to insertion into the borehole. This was absolutely necessary in horizontal or upward-slanting holes."

Jan 1, 1991

By Milos J. Bila

I would like to discuss today several safety topics that we at Nobel feel are going to be particularly critical to all of us who are involved in the manufacturing, transportation, storage and use of commercial explosives during the '90s. My purpose is to identify these topics in order to allow those in the commercial explosives community to better understand the potential difficulties we face.

Jan 1, 1992

By Sami Kara, Marsel Nabium

As a mining project is developed from conceptual to production phases, there exists a variety of uncertainties and difficulties that affect the operation’s designs and economic values. A notable design parameter to be taken into account is the factor of dilution. Dilution is the waste material not separated from the ore in the stages of mining and is sent to the processing plant. It is defined at the ratio of tonnage waste mined and sent for processing over the combined ore and waste tonnage milled. Dilution reduction is one of the areas that offer metal mines an opportunity to increase revenue and reduce costs, resulting in enhanced profits. Effective dilution control programs require interaction on a multidisciplinary level. This paper outlines recent initiatives undertaken at Polysmetal Silver Magadam Mine to reduce dilution and increase revenue. This paper provides an overview of the solution applied in underground Silver mine in Russia. The paper reviews the dilution problem throughout the entire mining process, and provides a rational approach to underground mine Blast design in order to minimize dilution. The mining companies put a lot of effort into extracting lower grade while minimizing cost. The dilution control assists with achieving this goal. In Polymetal Silver Magadam Mine we succeeded to control more than 20 blasts by keeping almost the same grade measured in the face. The results indicated that using the adequate blasting timing design can help to separate the ore from the adjacent waste in drift blasting with different ore body configuration.

By Thomas Barkley

Mining tradition holds that a parallel round underground can not be any deeper than it’s smallest face dimension. ln other words, a mine using a 12’ (3.7 m) high by 24’ (7.3 m) wide room and pillar mine, the deepest pull that can be achieved is plus or minus 12’ (3.7 m). After experience with decking of rounds in a 12’ (3.7 m) diameter shaft to achieve more than 12’ (3.7 m) advance per round, the concept of deepening the pull on horizontal parallel rounds seemed to be a feasible concept. Tests were conducted in a conventional room and pillar metal mine with a round size of 12’ (3.7 m) high by 24’(7.3 m) wide. Standard rounds were drilled with a 16’ (4.9 m) steel as parallel rounds to an average depth of 14.5’ (4.4 m). The average depth of pull on these rounds was about 13’ (4.0 m). Using the available drilling equipment, 20’ (6.1 m) drill steel was used to drill holes to an average depth of 18’ (5.5 m). Five rounds were drilled and shot with a resulting aven$e pull of 16.2’ (4.9 m) or 90 % of drilled depth. Rounds were designed with decked bum cuts to maximize depth of pull in the cut area An innovative method of de&mining drilling accuraq was used to estimate it’s effect on depth of pull in the rounds. This method used a standard automatic 35-mm camera and scaling to determine the average drill deviation for many of the holes in the rounds.

Jan 1, 2000