Search Documents

By Paul Worsey, Richard P. Ayres, Mark F. C. Schmidt

A new alternative technique designed to reduce rock scatter and flyrock during boulder blasting is being developed at UMR. The method uses small explosive charges and is designed for shooting in close proximity, while utilizing common blasting products found on the operators’ site. This ongoing work is being conducted internally as graduate and undergraduate level research. A paper describing the general technique was published in last year’s proceedings. This particular portion of the work was performed as an undergraduate research project as part of the requirements for the explosives emphasis degree option at UMR. Previous model work was performed using cubes of concrete. However, in real life boulders are often flat and irregular rather than perfect cubes. The purpose of this work was to determine how to deal with flatter boulders. The work comprised using different geometry blocks (simulated boulders) of the same volume (1 cubic ft.). Square concrete boulders using an 8.5bag concrete mix were cast using different width to height ratios (varying from 1: 1 to 3.7:1). Single 5/8 inch holes were drilled to 2/3 the depth of the blocks, charges placed approximately l/2 way in to the holes and the holes filled with water. The explosive charges comprised ICI Masterdets containing a OSg High Explosive base charge and incremental added weights of C4 explosive. In the experiments, the block height was progressively reduced and to compensate the charge weight was increased until acceptable fragmentation was achieved. It was found that a significant increase in charge wt is required to achieve the same fragmentation as the width to height ratio increases (the boulder becomes flatter). Furthermore, the increase in charge weight required is proportional to the width to height ratio. Basically, you have to use a higher powder factor for flatter boulders.

Jan 1, 2000

By Claude R. Ayoub, Charles A. Kliche, David G. McDowall

Homestake Mining Company's Open Cut Mine is located in Lead, South Dakota, in the northern Black Hills. The mine is within 300 feet of occupied residences on the south end, and within 1200 feet on the north end. Mining began at the north end of the open pit in October, 1983, and blasting related complaints began almost immediately. Noise and ground movement comprised the majority of the structural damage claims. As a result of these complaints, Homestake purchased a recording seismograph and began monitoring nearly every blast. In addition, the company hired a consultant to review Homestake's blasting and monitoring practices. He was also asked to do a single, one-time study of the cracks in six homes. This initial work led to Homestake monitoring all blasts with three seismographs and having South Dakota School of Mines and Technology do a year-long study of crack development and propagation in five homes in Lead.

Jan 1, 1989

By M. Oguz Ozkazanc, Gulsev Uyar Aldas

Because of its safety, being easy to handle, relatively inexpensive and containing a lot of energy, ANFO is the most popular and widely used explosive in Turkey as well as other countries in the world. According to change dated May 14th 1999 on the regulation 87/12028 related with explosives, blasters are not allowed to mix ammonium nitrate and fuel oil in the tield to make ANFO. Instead of this, they have been forced to use the ready ANFO prepared by explosive producer firms. As a result of this obligation, the use of technical nitrate for agricultural purpose and mixing AN and fuel oil in unsuitable conditions have been prevented. Indeed, wrong mixture means waste of energy and money.

Jan 1, 2001

By Hae-Moon Choi, Sang-Don Lee, Hee Soon Shin, Choon Sunwo, Chang-Ha Ryu, Hyun-Koo Lee

Building tunnels means dealing with what rock is encountered. Relocation of the site of the underground structure is rarely possible. Tunneling engineers and miners have to cope with the quality of the rock mass as it is. Different tunneling philosophies and different rock classification methods have been developed in various countries. Most of the rock classification methods are based on the response of the rock mass to the excavation. Tunnel support requirements could be assessed analytically, supplemented by rock mass classification predictions, and verified by measurements during construction. Rock mass classifications on their own should only be used for preliminary, planning purposes and not for final tunnel support. Design of blast pattern in tunneling projects in Korea is also for the most part prepared according to the general rock classification methods such as RMR or Q. It, however, does not take into account the blast performance, and as a consequence, produce poor blasting results. In this paper, the methods of general rock classification and blast design for tunnel excavation in Korea are reviewed, and efforts to develop a new classification method, reflecting the blasting performance, are presented. Copyright ©

Jan 1, 2004

By D Vrkljan, Z Ester

Excavating the building pit for the World Trade Center at Rijeka, it was necessary to blast over 160000 m3 of hard mass in fused condition. The building pit is located at a densely populated residential part of the main Croatian port Rijeka, close to the railway-track and traffic routes of the town. The permanent seismic monitoring points are foreseen on endangered housing and infrastructure facilities around the pit during designing and excavation of it. The seismic monitoring has been performed on 15 permanent points by occasion of over a hundred production and continuous blasting operations. The article considers the speeds of ground oscillations depending on applied maximum quantities of explosive charge according to fire degree, total quantities of explosives at the mine-field, structure of explosive charge, applied delay of mine boring and lines initiation mode and rock mass structure

Jan 1, 1999

By Dale S. Preece, Ruilin Yang

Shock wave physics is an important part of air-deck behavior since the bulk explosives in the column impart a shock into the air-deck where the air shock then passes through the air-deck at a rapidly attenuating velocity. Through both high-fidelity modeling and shock physics theory it is shown that the resulting pressure in the air-deck is two orders of magnitude less than the detonation pressure of the explosive. The induced air blast reflects from the bottom of the borehole and this reflected pressure, even though doubled, is still approximately two orders of magnitude less than the detonation pressure. Air-shocks will ring back and forth in the air-deck for a few tens of milliseconds while the adjacent explosive column(s) are detonating. Transmission of the initial shock through the air along with reflections is an intensive energy consuming process. Energy balance results in shock heating of the air and a temperature increase. However, the increased temperature of the air is also orders of magnitude less than that of the explosive detonation products immediately behind the detonation front. Replacing high energy explosives with zero energy air-decks in a blasthole will always have a negative impact on the adjacent rock fragmentation and movement.

Jan 1, 2016

By R Frank' Mammele Chiappetta, Conny Postupack

A major problem that has continued to plague the surface coal industry is blast induced damage to the coal seam. Atlas Powder Company has addressed this situation through seven years of field research in full-scale production environments. Many operations across the United States have been evaluated.

Jan 1, 1988

By Michael Wieland

The work principle from thermodynamics is used to model the shock and heave for explosives shot in rock or under water, with the latter compared to reported results. The work principle utilizes restrictions and constraints to yield a representative fit to the irreversible (natural) shooting process. The reduction of the internal energy of the reaction-zone yields the total expansion work (TXW), the resultant sum of the rock/water shock and heave. The restoration technique of forming a closed thermodynamic loop yields the reversible mechanical work (RMW) or the rock/water heave. The residual work that remains when RMW is subtracted from TXW yields the irreversible disorder work (IDW) or the un-dissipated (without loss) shock in the surrounding rock or water. The work principle renders an unequivocal relationship for the shock-loss factor, rather than the traditional roundabout formula for correcting the underwater gauge-shock of un-modeled explosives. There’s a novel heave-ratio factor that unquestionably rates the fit of results under comparison. Rock-shots are more complex in nature than underwater shots due to rock fracture and stratum rupture, though numerical resolution is worthwhile. The proposed rock-water-jelly (RWJ) model yields rough estimates, with rock-type results not wholly different from their underwater counterparts. Though reported underwater shots reveal shock and heave trends with respect to charge formulation ingredients, there are no such rock-shot results for comparison, since the relevant test measurements in rock remain difficult, if not intractable.

Jan 1, 2007

By A. S. Tawadrous

This paper is an evaluation of Artificial Neural Networks (ANN) as a tool in the design of the geometry of surface blast patterns. The built model uses eight different parameters, which affect the design of the pattern. Those parameters are rock type, stratification, blasthole diameter, bench height, type of explosive, priming position, powder factor and fragmentation size required. The network was trained to predict burden and spacing of the blast pattern. The model was built and trained (back-propagation technique) using 43 case histories collected from the literature. The model has then been validated using 16 cases from operational quarries.

Jan 1, 2006

By Julia Creasey, Natalie Hodgson, Claire Ward, Craig Davies, Helen Sarginson

"Emulsion explosive producers are attempting to lower the cost of emulsion production by using lowquality ammonium nitrate in emulsion formulations. Low quality ammonium nitrate contains additivessuch as anti-caking agents and crystal modifiers which contaminate the emulsions causing instability. This presents a need for an effective emulsifier that will maintain emulsion stability under thesechallenging conditions."

Jan 1, 2017

By Bryan J. Lane, Paul N. Worsey

The recommended maximum explosive weight for boulder blasting using internal charges is 0.1 O-kg/m” (3.5 oz./yd) (Olofsson, 1988). Normally this charge results in excessive scattering and flyrock, creating increased liability for the operator, especially in congested areas. An alternative technique using smaller explosive charges is being developed at the University of Missouri - Rolla. It is designed to reduce boulder scatter, flyrock and fumes and allows shooting in close proximity, using common blasting products.

Jan 1, 1999

By Mohammed Alkazimi, Katie Grantham

The purpose of this paper is to quantify the risk to both the environment and surrounding infrastructure from a pipe sealing implosion. Both accuracy and the precision in determining how a submerged infrastructure damaged by underwater explosions performs provide better decision-making capabilities for managers facing impending oil spills. This determination is vital, especially for both emergency and crisis management teams, as categorized consequences based on both the nature of the structural layout and the surrounding marine environment assist in identifying whether or not the utilization of this technique is applicable. Thus, the decision maker’s aim, in a crisis, is to minimize any associated risk that might result in aggravating the situation by endangering both the infrastructure and marine life. Therefore, the resulting risk matrices will enable technical personnel who are not experts in explosive technologies to be armed with the information necessary to determine if this mitigation technique is applicable to their situation.

Jan 1, 2013

By Roy McKinstry

In March of 2001, Barrick Goldstrike became the first surface gold operation in North America to evaluate the advantages of electronic detonators. A detailed study was conducted to quantify the benefits of the use of electronic detonators to the downstream excavation, crushing and ore processing operations. The following methods were used to quantify blast performance: High speed film and video monitoring Firing time and rock response analysis of the high-speed films Digital fragmentation analysis of the post blast muckpile Vibration waveform analysis (including Fast Fourier Transforms and seed waveform modeling) Excavator performance quantification Crusher, SAG mill and ball mill performance evaluation Ore recovery analysis Cost/benefit analysis

Jan 1, 2002

By E. Líder, J. Pavez, J. Rivera

The application of new technologies, methodologies, and the use of new products in mining operations is a practice that is becoming more common in the industry every day, added to the new challenges and restrictions found in the operation. In the city of Tierra Amarilla, the interaction between mining operations and the community presents a constant challenge given the proximity to the community and the limitations that this presents. Explosive charge mass, in conventional blasting using traditional explosives (ANFOs, packaged explosives for example) limits the explosive charge lengths (they are reduced), impacting the explosive charge productivity. To improve the productivity of explosive charge and fragmentation, the use of low-density explosives was proposed, allowing the increase of the explosive charge length, trying to maintain the vibration levels within the established limits (2mm/s), preserving the fragmentation of the rock in the required sizes. The present study shows the results obtained from the application of low-density bulk emulsion for production blasting charges using upward and downward fan drillings. During this process, 18 blasting events were carried out, of which 8 were Up-hole loading (average density of 0.75 gr/cc) and 10 with Down-Hole loading (average density of 0.95 gr/cc). In summary, a total of 110,760 tons of ore have been broken, using low density emulsion, meeting the proposed objectives such as: 33% reduction of vibrations, 12% overbreak (within the theoretical design), P80 of 11in and 4.6% in fines.

Jan 1, 2024

By Diego Quezada, Carlos Munoz, Marco Arellano

It is well-know that the presence of fine materials in mining has a direct impact on the plant processes with a great influence in the total amount of ore production and recovery. In Cu mining heap leaching is affected negatively by the presence of fines material (< 100 # Ty) in leaching piles, where a decreasing in Cu recovery is achieved in a lot of cases. D&B practices used normally in mine operations can generate fines > 4% in blasted piles, but the principal effects are reflected in the downstream processes where pre-conditioning post-blast materials release greater quantities of fines.

Jan 1, 2010

By Jhon Silva-Castro, Russell Lamont

Understanding the behavior of materials subjected to high strain rate conditions is of fundamental importance to the mining industry. Several stages of the mining process involve high speed loading rates including blasting, scraping, comminution, etc. Technical comprehension of how rocks deform, fracture, and fail under these loads is a fundamental first step required prior to any serious attempts at optimization of the energy utilized for pertinent activities in the mining process. A Split-Hopkinson Pressure Bar (SHPB) was designed and constructed at the University of Kentucky to study the dynamic properties of various types of rocks.

Jan 1, 2017

By Ruilin Yang

This paper provides a theoretical analysis of shockwaves in an air-deck induced by detonation of an explosive charge and shows that the initial shock pressure in the air-deck at the interface with the explosive charge is only about 1% of the detonation pressure. A rarefaction wave with the low pressure travels back into the explosion detonation products greatly reducing the post-CJ detonation pressure. Additionally, AUTODYN modelling shows that the pressure attenuates further during shockwave propagation along the air-deck. Although the pressure increases at the bottom of the blasthole due to shock reflection, the overall pressure in an air-deck does not increase and is still around 1% of the detonation pressure which is too low to break most rock.

Jan 1, 2016

By D J. McLane, J T. Rathbun, B T. Lusk

The dynamics of explosive detonations are understood, however recreating a real-world, full scale scenario is costly. The use of a shock-tunnel allows testing to be done on a smaller scale, with the simulated effect of a large explosion. Analyzing explosive waveforms using this method can greatly reduce cost in testing blast resistant products, such as anti-terrorism devices, mine safety products, and military equipment. The purpose of this paper is to better the understanding of how the waveform characteristics resulting from an explosive detonated within a shock-tunnel differ from those in an open-air arena test. The variables of comparison between an open-air arena test and those conducted within a shock tunnel are peak pressure, impulse, shock wave velocity, and cross sectional shape of the shock front. Understanding how these variables differ, tests utilizing a shock tunnel can be conducted with a higher degree of accuracy and repeatability.

Jan 1, 2013

By J. P. Remi Proulx, Juan Camilo Gonzalez T., Winston B. Wilches

Alabama USA based Drummond Ltd. operates two open pit mines in the Cesar Coal Basin of Northern Colombia. The mines produce a combined total of over 25 million tons (22.7 Mt) of thermal coal per year which is transported by rail to Puerto Drummond, a direct ship loading facility, where it is exported to over 15 countries. The company has proven and probable reserves in excess of one billion tons of thermal coal.

Jan 1, 2015

By Robert Hopler

209. Nitro-glycerine is produced by the action of nitric and sulphuric acids on glycerine, and is a heavy liquid of oily appearance, of specific gravity about 1•6, varying from colourless when quite pure to a yellow or brownish yellow. It is of a very sweet taste, and without odour, and is an active poison. Mere handling of it will in most persons induce sickness and headache. It explodes when heated to about 360° F. or from shock, but in small quantities it ignites and burns with some difficulty by the mere contact of flame.

Jan 1, 2011