Search Documents

By Ambrose Buchanan, Rob Farnfield, Charles Adcock

Beginning on 7th September 1940 the City of London was subjected to 57 consecutive days of bombing in what became known as the ‘London Blitz’. To commemorate the 70th anniversary of this event a television series was commissioned that required the open detonation of World War 2 equivalent bombs close to purpose built structures constructed using period design and materials. The structures were built on a remote test facility in the North of England that is able to fire large quantities of explosive in the air.

Jan 1, 2011

By Jean-Francois Lagueux, Andre Pomerleau

Goldex Mine is an underground mine located near the town of Val-d’Or. Multiple innovations were required to work the mine. Due to its low grade, it was important to develop a bulk mining method to economically extract the ore. The method used is a combination between shrinkage stope and long holes stope methods. This modified method is more than adequate; however, all of the ore body must be liberated in a very short period of time. Therefore, to bring down 23.0 M tonne (25.3 M ton) of ore, large blasts up to 1.8 M tonne (2.0 M ton) are required. The situation is also complicated by the fact that the mine is located in a residential area. No less that 40 homes are built within a 1 km (0.62 mile) radius of the mine site.

Jan 1, 2011

By Kia Riihioja, Mike Higgins

A major difference between electronic and pyrotechnic detonators is that, in almost all but the simplest of blast layouts, computer software is required to plan a blast using electronic detonators. While it may be possible to program delay times without software, using only the manufacturer’s control hardware, the full potential of electronic detonators can only be realized through software. Until recently, the only software available has been provided by the suppliers of the electronic detonators. These usually have just enough features to create a hole layout and to assign times to the detonators in the holes. The software is also able to communicate only with the manufacturer’s detonators. This means that the client may be compelled to change several parts of the blasting process when a different delay system is adopted, from design through to implementation and reporting, even though these may be sub-optimal at the client’s mine. While many authors have demonstrated improvements in blasting outcomes using electronic detonators, very few have discussed how the delay times were calculated. Where the calculations are discussed, it is also obvious that the delay times must be monitored and re-evaluated as conditions in the mine change. For example, the principles of superposition and scaled distance, burden relief and energy cooperation between holes should be checked constantly for different locations within the mine, changes in rock properties, or even for differences between design and actual hole positions. The most common methods in blast design software to calculate delay times are inter-hole interval, relief contour and direct editing. Although they are simple in concept, they can result in fundamental errors if they are not applied correctly. The software for electronic blast designs should be capable of not just a timing calculation, but also of showing, to some degree, the impact and interaction of the calculated times.

Jan 1, 2004

By Rolf Schillinger

Transport of Small Quantities of Explosives Material on Public Roads The transport of dangerous goods on public roads is extensively regulated by EU and national law. The transport of explosive material is not only done by forwarders but also by small companies and private persons with the goal of their own use. The following article tries to explain what is allowed and what is not.

Jan 1, 2010

By Tapan Goswami, Lloyd Hain, Geoff Brent

For many years Ramp 24 at Ensham mine in Queensland, Australia has suffered substantial coal loss and damage due to the fragile nature of the coal and problematic geological conditions, which have proved very challenging. In the past various blasting techniques were applied in attempts to improve coal recovery. One approach was to use a shallow throw (cast) blast followed by a separate post-strip blast underneath. Another method was the introduction of the practice known as “baby decking” with the addition of a large buffer of material in front of the coal. However, despite increasing mining costs, none of these techniques adequately reduced coal edge loss and damage.

Jan 1, 2008

By Dr. Bronwynne Victor, Quentin Steyl, D. Scott Scovira

Bulk emulsions and emulsion blends may be formulated with a single salt, dual salts, or multiple salts. Blasting professionals familiar with single salt ammonium nitrate emulsion products may be less acquainted with dual and multiple salt emulsion products that may include calcium nitrate, sodium nitrate, and urea in their formulations.

Feb 1, 2020

By Paul L. Matrin

This paper will discuss the recent and on-going drill and blast optimization measures at the Sparkhule Limestone Quarry, which have resulted in a 44% reduction of drill and blast unit costs per ton of broken limestone. This amounts to approximately $240,000 of drill and blast saving per year at current annual production rates of about 2.5 million tons (2.3 million tonnes) total material shot. The reduction of drill and blast costs were accomplished by a detailed and controlled in-the-mine drill/blast experimentation and cost evaluation using 8 different blast pattern designs and shots totaling approximately 267,000 tons (242,200 tonnes) of shot and mucked material. A careful review of the geology of the deposit was performed to determine the different rock classification/strengths/structural properties and to adjust blast designs to optimize fragmentation for the different rock types. Equipment loading productivity and crusher throughput performance were monitored as part of the evaluation process to assure that an optimal fragmentation of broken rock was achieved with the new blast designs. The study included the review of bulk explosive and accessory selection criteria (ammonia nitrate/fuel oil mix - ANFO, mini prills (high density ANFO), sensitized and un-sensitized emulsions at a 30% emulsion/70% ANFO blend), blast pattern design, charge diameter and the cost of drilling. Laser profiling technology was used to assure proper bench heights, stemming and sub-drill footage and front row burdens. High speed photography, video and still photos were taken of the different designed shots to assist in the evaluation of the performance of each blast. Powder density checks, size distribution, back break, detonation velocity and pressure measurements were taken. Different borehole diameters were used for the drill optimization study and drilling cost and productivities determined. A detailed cost comparison between in-house blasting and complete shot service was prepared to evaluate if shot service is a cost effective alternative to current in-house loading and blasting including a review of the new and pending United States Bureau of Alcohol, Tobacco and Fire Arms (ATF) regulations and associated owner costs/risks and potential benefit of shot service.

Jan 1, 2004

By David E. Siskind

Increased mineral consumption and environmental concern have caused much interest in potential damage and annoyance from ground vibration and airblast produced by production blasting in surface mines and quarries. Ground vibrations are traditionally blamed for "shaking the house to its foundations," but often the airblast is responsible, particularly when the distances from mine to structure are large. Simultaneous measurements of ground vibrations, structure vibrations, and indoor and outdoor noise from blasting are being used by the Bureau of Mines to determine the relative importance of the ground and airborne blast energy in shaking the structure and making windows, dishes, etc., rattle.

Jan 1, 1977

By Luana Ferreira de Carvalho, Aurelio Manço Garcia, Gustavo Sampaio Lopes, Jose Silvio Corsini, Davi Bastos Martins de Oliveira

The Enaex Mining Technical Solutions (EMTS) team, in partnership with the Anglo American Iron Ore Brazil drilling and blasting team, has developed a study aiming to optimize the blast design applied at the Minas-Rio project. The study consists of modeling the dynamic behavior of one lithological domain to determine the best configuration of drilling pattern, charge configuration, timing and sequencing of the blast designs applied at the mine in this particular rock. The first stage of the study was the recognition of the rock blast process in question, assessing key parameters that characterize this whole operation: geomechanical characteristics of the rock mass, implementation quality for drilling pattern and explosives charging (collar position, hole depth, explosive charge length and stemming size) and recognition of current blast designs. The central element of this study was the creation of a vibration attenuation and seed wave model which has allowed the characterization of this particular rock mass present in a region determined by the Minas-Rio team. The model is based on a near field vibration test, constituting a powerful tool in the design of blast parameters. The blast design developed from the damage model simulations basically modified the timing and sequencing. The aim of this study was to improve the fragmentation resulted by the blasting, considering the particle size requirements demanded by the primary crusher and to increase the productivity of the loading and hauling operations. The results were analyzed considering the effective productivity of the two different fleet types of shovels, where the authors have analyzed more than 46000 values of productivity from September 2017 to August 2018, taken from the Dispatch system. A significant increase in effective productivity of these load equipment was observed, 7% to the PC4000 fleet and 2% to the PC5500 fleet, values supported by statistical parameters and hypothesis tests.

By Luana Ferreira de Carvalho, Aurelio Manço Garcia, Gustavo Sampaio Lopes, Jose Silvio Corsini, Davi Bastos Martins de Oliveira

The Enaex Mining Technical Solutions (EMTS) team, in partnership with the Anglo American Iron Ore Brazil drilling and blasting team, has developed a study aiming to optimize the blast design applied at the Minas-Rio project. The study consists of modeling the dynamic behavior of one lithological domain to determine the best configuration of drilling pattern, charge configuration, timing and sequencing of the blast designs applied at the mine in this particular rock.

Feb 1, 2020

By S. Geerts, J Davidson

The purpose of the experiment was to determine detonation characteristics of various improvised explosives. The test consisted of detonating a pipe filled with an explosive compound inside of a plywood arena. The pipe will be located in the center of the arena to ensure even distribution on the witness panels. Details on pipe dimensions, weights of the pipe and explosive, and the density were recorded prior to testing for use in the model calculations. The same size pipes were used throughout to minimize the variables inherent in testing. The plywood witness panels will capture the fragments so that penetration data was obtained, primarily the surface area of impact and depth of penetration. Through the use of the penetration data in conjunction with a mathematical model the original fragment velocity was determined. The mathematical model was developed to measure lethality of fragments from explosives and was modified to determine the original fragment velocity instead. From this model other variables such as the Gurney velocity were calculated. This test was done with an explosive compound that was commonly found, and numerous improvised compounds. In order to guarantee accurate data all of the explosives used for testing were cap sensitive, to eliminate the need for a booster charge which would introduce many unknown variables. The one common explosive compound that was used was C-4 which has known data in order to show accuracy of the model and calculations. The other 5 compounds chosen will not have this data as they will primarily be improvised mixtures.

Jan 1, 2011

By Thomas Pallua, William C. Gates

"Two major railroad companies have identified several segments along the railroad corridor betweenTehachapi and Bakersfield, Kern County in California that require construction of a second track to improve operations in this area. The total project proposes an upgrade of five segments along the Tehachapi-Bakersfield route. The authors focused on two segments: Walong to Marcel and Cliff Siding Extension. The second track project comprised design of a through-cut adjacent to an existing tunnel and up to 120-feet-high (36m) side-hill cuts (both in granitic rock). The authors characterized the geologic ground conditions and ground behavior, including rock mass quality and strength using a combination of rock core drilling and rock slope mapping. The rock mass is generally characterized as granitic tonalite with strong core stones surrounded by a matrix of decomposed granite (DG)."

Jan 1, 2017

By Kenneth Faroni, Catherine Aimone-Martin, Thomas Gelormino

A blasting improvement program began in 1985 at two traprock quarries in Connecticut to reduce the levels of ground motions and airblast measured at residential structures surrounding the operations. The quarries are situated within town limits, adjacent to a number of historical and other structures. Although blasting vibration amplitudes were found to be far below those that could produce cosmetic defects in structures, they were perceived to be the cause of structural defects observed by homeowners. Based on a comprehensive * review of blasting practices in place during1985, an extensive vibration monitoring program was implemented. The initial study included the instrumentation of selected residential structures to record and analyze strains imposed within structures from quarry blasting, environmental changes, and from daily household activities. A comparison of the results was made with the results reported by the U.S. Bureau of Mines in 1980. The highest strain imposed in drywall from blasting (13 J_I strain) was 12% and 1% of the highest strain levels recorded for normal household activities and temperature changes, respectively. The present philosophy in production blasting is to attempt to keep vibration amplitudes as low as practical by implementing state-of-art blasting control techniques. Currently, blasting seismographs are placed in a circular manner around each quarry, providing production blast vibration records for 360 degrees of coverage at distances of 2500 to 4000 ft. from blasting operations. Seismograph and production blast records are analyzed each year and become part of a Blasting Improvement Plan submitted to the local zoning commission as part of the annual operating permit process. This paper summarizes the results of previous vibration monitoring programs and outlines the modifications made to blasting practices to minimize the levels of ground motions and airblasts. The public relations efforts and standard corporate procedures used by company personnel to address all blast related complaints and alleged damage claims since 1985 are also discussed.

Jan 1, 2000

By Eduardo Berger

This paper describes a mechanized loading system, the HYDRODOSE, which allows the use of pumpable emulsions in underground mining. It also describes a pumpable emulsion explosive for small diameter holes, HYDROMITE PDB. Included are test results carried out in two Chilean underground mines.

Jan 1, 1991

By Alejandro Rosario, Ricardo Dumuihual, Guillermo Silva, be nito Danial Valde, Carlos Scherpenisse

A monitoring campaign to record dynamic pressures generated by detonation of a single blasthole was implemented at Barrick Gold´s Pueblo Viejo Open Pit mine (PVDC), located in the Dominican Republic. Pressure amplitudes beyond the dynamic compressive strength of the electronic detonator´s capsules have the potential to damage these electronic devices, generating misfires along with all the associated risks and entailed safety implications. In most instances, misfires generated from high dynamic pressures are a direct consequence of drilling deviations resulting in blasthole distances smaller than originally designed. Tourmaline Crystal Sensors specifically designed for high dynamic pressure measurements in aqueous media were selected to address the challenge. These sensors are custom-made and require additional instrumentation for proper operation, including signal conditioners and recording equipment capable of capturing simultaneous events, both in their amplitude and frequency components. Field-testing comprised detonation of a single blasthole using current explosive loading practices along with an arrangement of sensors positioned within water-filled drillholes in a spiral configuration. Distances, explosive weights and all 23 dynamic pressure record amplitudes are included along with additional data regarding arrival time and P-Wave velocity estimations. As with typical vibration models, the Scaled Distance concept (D/W1/2) was used to construct an attenuation model relating Dynamic Pressure as a function of Distance (D) and explosive Weight (W). The resulting model, adjusted to a 95% statistical confidence limit (covering 100% of the recorded data) was used to generate a series of curves (Abacus) estimating dynamic pressure as a function of distance for different explosive charges. These curves, in association with permissible pressure limits defined at 50% (FOS = 2) of the dynamic pressure strength reported by manufacturers for both, the 1000bar (Al) and the 1400bar (Cu) capsules; allow for the determination of critical (safe) distances between blastholes. Tests were implemented to cover a variety of field scenarios, accounting for different rock mass types, qualities and water conditions; however, preliminary analysis indicate the convenience of developing a unique trend that considers said variability. This approach allowed construction of a single, simple, unambiguous and operationally applicable design tool to address entailed safety issues.

By Clara Godoy, Álvaro Dapía, Paulo Couceiro, Håkan Schunnesson, Juan Navarro

This paper applies geostatistical tools in Measure While Drilling (MWD)data to estimate the probability distribution of values in all the points of the studied domain in order to assess the continuity of rock classes between boreholes. The analyses carried out by Ghosh et al.(2018) and Navarro et al.(2019) have been used as starting point of this work to classify the geotechnical rock condition in four classes: solid rock, fractured rock, cave-in rock and cavity. From it, an application for the geotechnical rock condition of ore bodies have been developed, aiming at characterizing the rock before the charging the holes to minimize unexpected rock conditions and to address issues associated with charging and blasting operations. Such problems are closely related with non-optimal rock fragmentation after blasting. The procedure has been applied in the geotechnical block model results obtained from Navarro et al.(2019)’s work in the Luossavaara-Kiirunavaara AB’s (LKAB) Malmberget underground iron ore mine, Sweden. Navarro et al.(2019)’s model was developed based on102 fan-holes from five ore bodies and extrapolated to the full-scale in20 drifts with 5600 fan-holes from two orebodies. A multi-step transformation of the MWD parameters was carried out in order to minimize external influences other than the rock mass. The study shows the calculations of the variogram and kriging estimation in the 3D domain for six ring-blasts, from one of the ore bodies studied in Navarro et al. (2019)’s work to assess the continuity of the rock classes along the six ring-blasts in a 3D mapping model. For that, intermediate rings between the measured ones from the MWD have been estimated. The probability distribution of values in the entire domain of rings with measured samples has been plotted together with the rock classes identified by the blasthole paths. The results show high accuracy in the matching between the kriging and the values given by the MWD data, allowing to visualize smooth trends of different rock classes along the ring. The representation of the 3D mapping model for the six ring-blast shows clear fractured and cave-in zones developed along the drift that correspond to zones with geotechnical problems found, as from internal reports.

By Philemon Desrochers, Ken Qian Liu

Following the success of the West Ore Zone distress mass blast in 2001 at Brunswick Mine, a similar approach was taken to distress the North Regional Pillar (NRP) which contained over 3 million tonnes of high grade ore. The NRP is located on the 1000 m Level with very poor hanging-wall (H/W) rock mass qualities. After an extensive geotechnical review, the distress slot is located close to the foot-wall (F/W) of the NRP in order to have the competent ore as H/W. The longitudinal area to distress covers 115 m along the strike and 85 m high from 1000 1-sub to 850 Sill. Prior to the final mass blast, 3 voids were created to allow rock swelling: the North void, the South void and the trench just below the mass blast. After over one year of preparation, the mass blast of 202,000 tonnes was successfully initiated on February 7, 2003 with 1561 electronic detonators and 210,000 kg of emulsion explosives. The blast achieved its objective of distressing the NRP as indicated the mine-wide micro-seismic monitoring system. This paper describes different stages of the project from void preparation to the mass blast itself, as well as some detailed aspects such as muck-pile prediction for mucking sequence with the help of DMC_Blast simulation code and electronic detonators.

Jan 1, 2004

By John Vynne

BHP’s Navajo coal mine installed drill monitoring and high precision navigation systems on their three overburden drills during 2002 and 2003. Details of the DrillNav system hardware and reporting system will be discussed, as well as the significant benefits Navajo has achieved since the systems were installed. Navajo is not satisfied with the current results and plan additional upgrades to the systems. In addition, Navajo plan to integrate the data from their drill systems with data from other systems to achieve even greater increases in drill productivity and to reduce overall mining costs.

Jan 1, 2007

By Bill Birch, Toby White, Ian Brown

costs/benefits of electronic detonators and measure their effects on primary crusher productivity. 9 blasts (3 shock tube blasts, 6 electronic blasts). Measured electricity consumption & primary crusher throughput. Change to Electronic Detonators resulted in a 7% reduction in primary electricity costs and a 15% increase in primary crusher productivity.

Feb 1, 2020

By J. Pizarro

Any organization that subjects its activities to a continuous improvement methodology, aiming to optimize their processes and services, must be able to adequately measure the results of the implemented changes to pursue better outcomes. This is no different for mining companies. When it comes to blasting, an accurate fragmentation analysis can correlate blast design and rock mass parameters to particle size distribution, enabling us to further analyze the correspondence of specific design patterns, applied to specific rock mass properties and the result in measured fragmentation indicators. Over time, many tools were developed for us to obtain PSD data, albeit each of them had their own shortcomings. The first ones to be developed involved photographing the muck pile including a scale object, uploading those photos to a PC, and using specialized software to analyze each one. As a result, analysts would get a PSD curve that served as reference for the performance of the blast. This method, which is still used, has major shortcomings. The most obvious one is that it is only able to capture a slice of the blast, which corresponds to the exposed section of the muck pile the analyst has access to, and even there its reach is limited to the areas that are safe for getting close enough for placing the scale, which are not many. Consequently, this is a very limited way to get a fragmentation performance assess for a blast. Currently, autonomous systems are capable of taking continuous pictures of the muck pile. Installed on a shovel, conveyor belt or crusher feed, these systems can take a continuous stream of pictures that are later analyzed automatically without the need of human intervention. These systems greatly increase the volume of data and, consequently, we have a PSD curve that is more representative of the blast performance. However, this technology still had issues when trying to sample front end loaders mining operations or getting results from underground blasting due to the inherent difficulties of these operations. New algorithms used for capturing and processing data for front end loaders can overcome the harsh environment of their operations and produce PSD data in high vibration environments and difficult mining angles. For underground mining, algorithms can be used to sample each truck exiting the mine, giving a reliable source of fragmentation analysis that can be traced back to their stope of origin. The development of this technology extends the existing system’s capabilities and helps us in our efforts to improve fragmentation results with each blast.

Jan 1, 2024