Search Documents

By Richard S. Gaps

The Derby and Alexander Claim, located within the Tunnel Ridge Wilderness Study Area (WSA), has placer gold resources. No lode deposits are known within the area, but lode gold deposits are found within 1 1/2 mi of the WSA. In additon, rock units which contain lode gold deposits north of the WSA are found within the northern portion of the study area. INTRODUCTION The Tunnel Ridge Wilderness Study Area (WSA), CA-030-402, encompasses 4,623 acres of BLM administered public land in Trinity County, California, about 35 mi west-northwest of Redding (fig. 1). Major access to the Tunnel Ridge vicinity is by U.S. Highway 299. Ac-cess to the WSA boundary is by a secondary paved road from Junction City and several light duty dirt and gravel roads (fig. 2). The WSA is on the southwest slope of Weaver Bally Mountain. The topography is rugged with moderate to steep slopes; elevations range from about 1,600 ft to 5,900 ft.

Jan 1, 1983

A system to continuously measure the concentration of radon in mine ventilating air has been developed and tested in a uranium mine. In use, the air/radon mixture to be monitored is pumped through filters into a scintillation cell where nuclear decay of the radon produces flashes of light. These are electronically counted, giving a quantitative measure of the radon present. Air is continuously drawn from the mine atmosphere into the radon sensor box. This air sample passes through two filters into the detector cell as shown in the schematic diagram. A portion of the radon in the detector cell will experience nuclear decay, producing polomium 218 and an alpha particle. The alpha particles from the fraction that decays strike a zinc-sulfide coating on the inside wall of the cell and produce flashes of light. These enter a photo-multiplier tube which records each flash as an electrical pulse. An amplifier increases the voltage of each pulse, allowing electronic screening to remove noise and other undesirable pulses. The remaining pulses are counted by a conventional data acquisition system.

Jan 1, 1978

By Rudy J. Matetic

The National Institute for Occupational Safety and Health (NIOSH) at the Pittsburgh Research Laboratory (PRL) is conducting research to reduce the noise exposures of roof bolting machine operators and to prevent additional cases of Noise Induced Hearing Loss (NIHL) thru the development of engineering noise controls. This paper describes and evaluates an engineering noise control for the roof bolting machine, namely the collapsible drill steel enclosure. The results of the evaluation demonstrated that using the collapsible drill steel enclosure provided a 7 dB(A) reduction in sound pressure level at the operator?s position of a roof bolting machine.

Jan 1, 2008

Quickly and cheaply consolidate underground slimes to facilitate their use as backfill and permit their easy handling for other reasons. Approach: The slurry containing slimes is pumped into active stopes and electrokinetically dewatered to provide consolidated back fill. How It Works: To densify slimes electro-kinetically two electrodes are placed in the material to be dewatered and densified. Typically, the electrodes are pieces of wire mesh fencing. One is placed on the bottom, and the other is suspended in the slurry near the surface. Figure 1 is a simplified section of a test. A d-c voltage of 100 to 400 volts is applied across the slurry. This causes the solid particles which are in suspension in the water (usually these are negatively charged) to migrate toward the anode; simultaneously, the water moves toward the cathode. Water immediately adjacent to the negatively charged solid particle surfaces contains an excess of dissolved positive ions. When these ions are attracted to the electrode and move towards it, they also exert

Jan 1, 1976

Research personnel from the Bureau of Mines, representatives of the Mining Enforcement and Safety Administration (MESA), and members of the mining industry met with other Government and Industry representatives at three seminars held in Pittsburgh, Pa., November 4, 1975; St. Louis, Mo., November 6, 1975; and Denver, Colo., November L1, 1975, to discuss the results of Bureau-sponsored research on coal mine illumination. The program, aimed at developing suitable illumination systems fur the working; places of underground coal mines, covered hardware development and field evaluation and the status of proposed MESA standards and proposed MESA enforcement procedures. These proceedings contain the opening remarks to the seminars and eight technical presentations an various aspects of coal mine illumination.

Jan 1, 1976

By Christopher C. Jobes, Alan G. Mayton

The National Institute for Occupational Safety and Health (NIOSH) researchers have investigated seat design issues for the occupants and operators of underground mine transport vehicles relative to whole-body vibration (WBV) and mechanical shock. Considering the ergonomic and engineering improvements made to underground mine shuttle car seats, this study has focused on reducing injury risk by improving seating on transport vehicles such as scoops, mantrips, personnel carriers, and rail-mounted locomotives. Similarly, proposed seat design improvements included layering of various types of viscoelastic foam padding to isolate vehicle occupants and operators from adverse health effects of jarring/jolting exposure. This paper discusses the results obtained from laboratory vibration testing of new seat padding materials in seven configurations at the NIOSH – Pittsburgh Research Laboratory (PRL) showing that careful use of configuration and materials can reduce the operator’s exposure to WBV. In addition, results for four mine transport vehicles are presented from field data collection efforts at a Southwestern Pennsylvania mine showing that a NIOSH based design does reduce the operator’s exposure to WBV. Finally, the authors discuss efforts to develop and field test seat padding interventions using new padding materials and configurations based on the laboratory test results [The findings and conclusions in this report are those of the author(s) and do not represent the views of the National Institute for Occupational Safety and Health.]

By Manuel Gomez

This report presents prediction equations for 12 variables that are indicative of metallurgical coal quality. The variables include six for coke strength and six for carbonization product yields. All variables were predicted for coking coals having volatile matter contents from 16.3 to 42.1 percent, dry basis. The prediction equations, developed by mathematical-statistical techniques, were based on information from the proximate and ultimate analyses, the size consist, and the petrographic composition of bituminous coals carbonized in BM-AGA retorts at 800°, 900°, and 1,000° C. The equations were evaluated for validity with independent data derived from the 900° C carbonization of 33 binary blends of various coals and 22 binary blends of Pocahontas No. 3 low-volatile bituminous coal with 11 high-volatile bituminous coals. Results show that metallurgical coal quality can be predicted ahead of mining because data used to derive the prediction equations can be obtained at the time of exploration. Capability to forecast coal quality is useful in mine planning and should provide basic information for optimization of blending and crushing techniques and thus lead to the production of uniform coke.

Jan 1, 1970

By L. McWilliams, L. D. Patts, J. D. Noll, S. E. Mischler

Elemental carbon (EC) is currently used as a surrogate for diesel particulate matter (DPM) in underground mines since it can be accurately measured at low concentrations and diesels are the only source of submicrometer EC in underground mines. A disadvantage of using EC as a surrogate for DPM is that the fraction of EC in DPM is a function of various engine parameters and fuel formulations, etc. In order to evaluate how EC predicts DPM in the underground mining atmosphere, measurements of total carbon (TC; representing over 80% of the DPM) and EC were taken away from potential interferences in four underground metal/non-metal mines during actual production. In a controlled atmosphere, DPM mass, TC, and EC measurements were also collected while several different types of vehicles simulated production with and without different types of control technologies. When diesel particulate filters (DPFs) were not used, both studies showed that EC could be used to predict DPM mass or TC. The variability of the data started to increase at TC concentrations below 230, µg/m3 and was high (>+20%) at TC concentrations below 160 µg/m3, probably due to the problem with sampling organic carbon (OC) at these concentrations. It was also discovered that when certain DPFs were used, the relationship between DPM and EC changed at lower DPM concentrations.

Mine fires pose a serious hazard to the health and safety of mine workers. They occur regularly and their effects can be devastating. Objective Provide mine safety personnel, MSHA, and equipment manufacturers with a comprehensive, up-to-date, and well-documented database of metal and nonmetal mine fire incidents in the United States from 1950 to 1984 and perform a statistical analysis of these incidents. The data-base is designed for use by mine engineering and safety personnel to aid in determining especially hazardous practices or conditions.

Jan 1, 1988

By Ruth A. Holmes

A Bureau of Mines method for recovering nickel, cobalt, and copper from low-grade domestic laterites is described, which includes the unit operations of solvent extraction and electrowinning. Previous Bureau work indicated that addition of Na2S04 (sodium sulfate) to the nickel electrolyte improved current efficiency in nickel electrowinning. The present study determines the compatibility of Na2S04 with nickel strip-ping in the solvent extraction operation of the Bureau method. The effect of adding 100 g/l Na2S04 on nickel stripping, phase disengagement, and pH was determined in comparative laboratory-scale tests. In continuous-circuit testing, Na2S04 reduced stripping efficiency to the extent that five, instead of four, strip stages were required for complete stripping of nickel from the loaded solvent. In tests made in a phase-disengagement cell that had a variable settler area, the addition of Na2S04 did not significantly affect phase separation characteristics. The pH of the nickel electrolyte in the temperature range of 20° to 65° C was also unaffected by the addition of Na2S04. An economic evaluation showed that the energy saved by adding Na2S04 to the electrolyte would more than offset the cost of adding another stripping stage.

Jan 1, 1983

By Harlow D. Phelps

"INTRODUCTION The Copper Butte mine was examined, surveyed and mapped (fig. 1) by a Bureau of Mines engineer in January 1944. As a result, it was decided to diamond-drill the deposit, using Bureau of Mines equipment, and drilling was started October 14, 1944, under the supervision of two Bureau engineers, and stopped April 5, 1945. Nine holes were drilled for a total of 1,274 feet, not including 48 feet on a lost hole. Figures 2 and 3 are sections at AA' and BB' of figures 1, and show the adjusted average assays of drill-hole samples. Figures 4 and 5 are separate maps of holes 4 and 6, respectively.ACKNOWLEDGEMENTSIn its program of exploration of mineral deposits, the Bureau of Mines has as its primary objective the more effective utilization of our mineral resources, to the end that they make the greatest possible contribution to the national security and economy. It is the policy of the Bureau to publish the facts developed by each exploitation project as soon as practicable after its conclusion. The Mining Branch, Lowell B. Moon, chief, conducts preliminary examinations, performs the actual exploratory work, and prepares the final report. The Metallurgical Branch, R. G. Knickerbocker, chief, analyzes samples and performs beneficiation tests. Both these branches are under the supervision of R. S. Dean, Assistant Director."

Aug 1, 1946

By Danny A. Riley, James R. Sanger, Hani S. Matloub, Lin-Ling Zhang, Ji-Geng Yan

This experimental study was done to determine pathological feature of vibration injury to the peripheral nerves in the hind limbs of rats exposed to 7 days of vibration. Materials and Methods Animals: Twenty four male Sprague-Dawley rats weighing 350-400 grams were randomly divided into two groups: sham control group and vibrated group. To document vibration-induced changes in the experimental model, the sciatic nerve was used because it contains both motor and sensory fibers and is relatively superficial in the posterior thigh. Customized Vibrating Platform: The hind limbs of the rats in the vibrated group were exposed to vibration in a custom-built vibrating apparatus consisting of two platforms: a smaller vibrating platform on which the hind limbs of the rat are secured, and a larger platform on which the remainder of the body rests. The vibration parameters (frequency 43.5 Hz, amplitude 1.5mm, acceleration 4.75G, velocity 6cm/sec., and displacement of 3.0mm) of this model were measured. Methods: Rats were anesthetized with 35mg/kg of intraperitoneal Nembutal (phenobarbital) and their hind limbs fixed to the vibrating platform by Velcro loops. Both hind limbs rest on the vibrating platform while the remainder of the body rests on the larger platform. The rats were vibrated 4 hours a day, for 7 days, with close monitoring of the vibration parameters. The 4-hour duration of hazardous vibration was based on recommendations from the British Standards Institution. The sciatic nerve of rats not exposed to vibration, but similarly anesthetized and secured to the vibrating platform, acted as controls. At the end of seven days of exposure to vibration, nerves from both the vibrated rats and the control rats were harvested after perfusion of the lower half of the body using glutaraldehyde as described below. Neural Fixation: The aorta was cannulated, and the inferior vena cava was nicked and the animal was initially perfused with 0.9% buffered sodium chloride. This was followed by perfusion of a filtered mixture of 3% glutaraldehyde and 3% paraformaldehyde fixation solution, The tissue was subjected to post fixation by routine. The neural tissue was then submitted for light and electron microscopy. Results While light microscopy showed minimal histological differences between vibrated (n=12) and control nerves (n=12), the changes revealed by electron microscopy were dramatic. These included thickening of the epineurium, as well as thickening of the myelin sheath as compared with normal nerve. Also, the axon plasma was detached from the myelin sheaths, and many vacuoles were seen between the myelin laminae(Fig.1); These changes were found in all vibrated animals, and in the whole segment of each vibrated nerve. Myelin balls, consisting of

Jan 6, 2006

By Jueun Lee, Jong-Hwa Yoon, K. Rider, Bernard J. Martin

Whole body vibration is known to affect movement accuracy [1], however little is known about changes in the organization of movement and movement strategies used to limit the influences of perturbations. The specific aim of this work is to analyze the motion and coordination of upper body segments of seated operators performing reaching tasks under whole-body sinusoidal vibration exposure and simulated vehicle ride motion. The long-term objective is to model reach coordination and predict the dynamic behavior of the upper body motion under vehicle vibration exposure. Method The reach task consisted of pointing with the right hand index finger to targets located on touch screens placed in front of the subject, 45° overhead and 90° to the right in the mockup cabin of an HMMWV placed on a 6 DOF ride motion simulator. The task was performed under stable (no vibration) and vibration (sinusoidal vibration or simulated ride motion) conditions. A motion capture system was used to record kinematic data of reflective markers to recreate body link trajectories. Joint angles (torso, shoulder and elbow; Figure 1) were then computed using quaternions. Coordination between body links was defined as a) the joints angle-versus-angle relationships between the upper arm and lower arm, and b) the joint motion onset relationships between torso, upper arm and lower arm in the time domain. Results Angle–versus-angle relationships. The relationship between upper arm vs. lower arm angle and torso vs. upper arm angle for a far forward reaching movement in the stable (solid lines) and vibration conditions (dotted lines) are illustrated in Figure 2. Fig 2A compares the control condition with a 4 Hz lateral vibration while Fig 2B compares the control condition with a 6 Hz vertical vibration. It appears that under vibration exposure the reduced upper arm extension is compensated by an increase in torso flexion. This effect is seen in the last phase of the movements (encircled areas). In addition, the lower arm extension is delayed under 6 Hz vertical vibration (Fig 2B left panel). Time of joint motion onset. The timing relationship between torso, upper arm and lower arm is largely a function of the target to be reached. Examples of delays between body links are illustrated in Figure 3. The control condition is compared to a 6 Hz vertical vibration for three

Jan 6, 2006

The State of Washington has a federal program that gives the Office of Surface Mining responsibility for assuring the reclamation of lands affected by coal mining. Most of Washington's coal-bearing regions lie west of the Cascade Mountains. The state's coal reserves are estimated at 1.4 billion tons, about 0.3 percent of the nation's total coal reserve. Steeply dipping. minable seams range from 2.5 to 25 feet in thickness. The occurrence of coal in Washington has been documented since the early days of its settlement; at one time, coal production played a significant role in the state's economy. During the late 1800s and early 1900s, coal was second only to lumber in Washington's industrial production. Coal production declined as other sources of energy were developed. By 1959, production was at 200,000 tons. Regulation of the coal mine operations in Washington is conducted by the Office of Surface Mining's Casper, Wyoming, Field Office and its local office in Olympia, Washington. All permit applications and abandoned mine land reclamation are completed by the OSM Western Support Center in Denver, Colorado. Inspections of mine and reclamation sites are conducted by OSM reclamation specialists located in Olympia.

Jan 1, 1992

By Terry J. Kreidler

In recent years, west-central Arizona and adjacent California have become the focus of geologic and exploration attention because of its excellent exposure of detachment-fault terrane. Detachment faults, normal faults with nearly horizontal fault planes, are the result of regional extension. Rocks on the lower plate consist of mylonitized intrusive, metasedimentary and crystalline rocks highly altered to chlorite; upper plate rocks comprise sedimentary, volcanic, metasedimentary, and metavolcanic rocks. The movement of the detachment fault causes the rocks on the upper plate to be severely fractured and brecciated thus making them Ideal conduits for mineralizing fluids. Mineralization favored the more reactive sedimentary and volcanic rocks of the upper plate. Three gold deposits, located in upper plate rocks, are currently being mined along the Colorado River corridor: the Picacho Mine near Yuma, Arizona, 70 mi south of the study area; the American Girl Mine In southeastern California, 60 mi southwest; and the Copperstone Mine near the southern end of this study area. Samples from the above three mines were used to create a geochemical model of detachment-related gold deposits. Antimony, arsenic, barium, copper, mercury, molybdenum, manganese, tungsten, and zinc all occur In the mine samples in concentrations at least three times greater than found elsewhere in similar rock types. Samples taken by the Bureau from the wilderness study areas contain similar anomalous concentrations of the same elements as well as elevated concentrations of several other elements Including: lead, fluorine, cerium, uranium, and samarium.

Jan 1, 1992

By Stephen R. Iverson

Mineral deposits examined in and near the Raywood Flats RARE II area have low potential for development. The Mill Creek Mine (fig. 1), has produced about 14,000 tons (13,000 t) of marble, and another 5.5 million tons (5.0 million t) of marginal marble reserves suitable for lime, chemicals, and cement production are estimated to remain at this deposit. However, nearly all the marble is outside the study area. The deposit is marginal because alternate sources of marble are closer to markets. A tungsten occurrence in the marble is too small and low grade to be considered a resource. Ten tons (9.1 t) of uranium- and thorium-bearing material have been mined from a pegmatite dike at the St. Patrick Mine. However, this occurrence also is too small and low grade to be considered a resource. More than 400 lode and placer claims have been located in or near the study area. There are no current claims or mineral, oil and gas or geothermal leases.

Jan 1, 1983

By Nicholas T. Zilka

Mineral resource studies by the Bureau of Mines indicate three areas within the Selway Bitterroot Wilderness have mineral resource potential. Regional studies suggest that a granitic stock on the south side of the Wilderness has high potential for a Climax-type stockwork molybdenum deposit (pl. 1, no. 8); but detailed surface investigations failed to recognize a deposit. The Elk Summit area on the north side of the Wilderness contains subeconomic resources of columbium (niobium)-bearing ilmenite in placers (p1. 1, no. 19). Subeconomic silver-copper-lead resources occur in a vein on the northeast side of the Wilderness at the Clift Mine (pl. 1, no. 2-5). The study area has no known deposits of oil and Haas, coal, geothermal resources, or other energy-related commodities.

Jan 1, 1982

By W. Timothy Adams

The production of natural abrasives varied in quantity and value compared with 1976. Output of tripoli-type materials was approximately the same in both quantity and value. Special silica stone products decreased in quantity and increased in value. Garnet production decreased both in quantity and value. The production of emery increased and the production and value of manufactured abrasive material was approximately the same. Foreign Trade Imports of abrasive materials were 23% more in value than in 1976, and exports plus reexports increased in value 10%. Net imports, the excess of imports over exports and reexports, were $35.3 million. The volume and value of all abrasive materials exported varied.

Jan 1, 1980

By R. H. Grau, R. B. Krog

The National Institute for Occupational Safety and Health (NIOSH) has investigated the unique ventilation requirements of large-opening mines to help identify and evaluate the effectiveness of various fan types to improve the ventilation and air quality in the underground workplace. Large-opening mines, with their low airflow resistance factors, can be ventilated with free-standing auxiliary fans because airflow pat-terns in these mines are primarily controlled by airflow momentum. The flow characteristics of both vane-axial and propeller fans were investigated and tested at four large-opening mines to assess the effects of fan location on recirculation and entrainment. Each fan type has its own airflow, entrainment and penetrating air-flow characteristics, and operating costs that are advantageous for specific applications. Either fan type can be used for most auxiliary applications. However, this research has shown that the optimum placement and use criteria for propeller fans differ from those promulgated by the U.S. Bureau of Mines (USBM) for vane-axial fans Brechtel et al. (1985)

By David E. Van Dillen

The computer program described in this user's guide provides for the static, three-dimensional, linear and nonlinear analysis of structural and geological systems by the finite element method. The guide describes the capabilities and general features of the program and shows how input is prepared. A number of recent advances in finite element theory and computer technology are incorporated in the program. Nonlinear material properties are provided for, including isotropic, anisotropic, and time-dependent material properties, gravity loading, simulation of a sequence of excavation or construction, and a slip or joint element. The finite elements include beam, rod, axisymmetric and plane quadrilateral, hexahedron, thick shell, axisymmetric and plane joint, and a three-dimensional joint. The program also has an automatic mesh generator to minimize user input preparation for continuum finite element meshes.

Jan 1, 1981