Search Documents

Table 1.-Salient statistics of carbon black produced from natural gas and liquid hydrocarbons in the United States [ ]

Jan 1, 1967

By C. H. Fisher

[Many methods of analyzing tar oils for their tar acid and base content have bun employed in connection with both academic and. industrial investigations. Most of these analytical procedures are based on the diminution in volume caused by extraction with alkali and mineral acids (contraction method), although other methods haves been employed.4/ In many instances the adoption of an analytical method was not preceded by adequate study, and, as a consequence, the literature, on this subject is conspicuous for its contradictory claims and recommendations. It has bin shown in the, case of certain synthetic solutions5/ that large errors may result if the analysis is carried out by simple extraction with alkali and mineral acids.]

Jan 1, 1936

By Norman G. Foster

The mass spectra of 14 previously unreported alkylthiophenes are pre-sented. Low ionization voltage data of selected compounds from these 14 and 23 previously reported alkylthiophenes are presented and discussed for their value in supporting fragmentation mechanisms analytical correlations. A comparison with and corroboration of earlier correlations is made. Additional correlations concerning detection of side chain branching and the detection of ethyl-alkyl and propyl-alkylthiophenes are made. A discussion of the possible fragmentation routes and mechanism of fragmentation is given. Speculative structures are inferred s out some of the ions and hence this work provides a basis for suggesting fation mechanisms for the alkylthiophenes according to modern theories ass spectrometry. Verification of these mechanisms must await the availability of isotopically labeled molecules which are labeled in specific lotions that permit the definition of the paths of frag-mentation. Some suggestions for further work to generalize on the correlations and studies made to this point are presented.

Jan 1, 1965

By S. P. Kinney, P. H. Royster, T. L. Joseph

"The study described in this paper, on the reactions in an iron blast furnace, is part of the investigation being conducted by the Bureau of Mines on combustion of coke and the reduction of iron oxides in the blast furnace. Previous study of the combustion zone of the iron blast furnace, by means of a series of as samples taken through the tuyeres across the hearths of 13 blast furnaces, showed that the combustion of the coke in the blast-furnace hearth is complete at a distance of 32 to 40 inches from the nose of the tuyere, measured horizontally toward the center of the furnace. The results of this previous work are sum¬marized in the curves shown in figure 1, where it will be noted that practically all of the oxygen disappears at a distance of approximately 30 inches from the nose of the tuyere.In order to determine the height at which oxygen is found in a vertical direction above the tuyeres - it had been suggested that the combustion zone turned upward near the tuyere and to obtain comparisons with the samples taken at the Bureau of Mines experimental6 (5-ton) blast-furnace at Minneapolis, the Bureau extended the gas sampling on a commercial furnace to a number of planes between the tuyere level and the stock line. The sampling was conducted on a 300-ton furnace, making foundry iron, operated by the Central Iron and Coal Co., at Holt, Ala. The furnace was smelting Southern red and brown ores and nodules from pyrite sinter. Figure 3 is a vertical section of the furnace showing the six planes sampled."

Apr 1, 1926

By F. E. Harris

The United States produces about 30 percent of the world output of salt. Numerous deposits occur in widely separated areas, but the leading producing States are California, Kansas, Louisiana, Michigan, New York, Ohio, Texas, Utah, and West Virginia. Although no great amount of salt is produced at present in Pennsylvania, the potential sources in that State recently aroused a good deal of interest. The United States salt industry is highly organized; it comprises fewer companies than when small crude works with primitive methods and equipment eked out salt for local needs, but concentration of output brought about by modern inventions and methods of production has improved the quality of the produce greatly and accelerated production.

Jan 1, 1939

By R. J. Kuczynski

The U.S. Bureau of Mines operated a 2,000-g (4.4-lb) batch process development unit for recovering platinum-group metals (PGM) from automobile catalysts. Virgin monolith, used pellet, and used monolith catalyst samples were tested. Leaching twice with 1-pct sodium cyanide (NaCN) solution at 1600 C for 1 h dissolved more than 95 pct of the PGM from virgin catalysts and more than 90 pct from used pellet catalysts. More than 85 pct of the PGM was dissolved from used monolith catalysts when a third autoclave step was added. Solid PGM concentrates containing more than 99.8 pct of the dissolved PGM and analyzing greater than 70 pct PGM were recovered by heating the pregnant leach solutions from virgin catalysts to 2500 C and used catalyst to 2750 C for 1 h. The solution after heating contained less than 0.2 ppm. total cyanide. The virgin residues passed the EPA Extraction Procedure Toxicity Test (EP Tox Test), the EPA Toxicity Characteristic Leaching Procedure (TCLP), and the California Waste Extraction Test (WET) for all elements except Ba. Adding sodium sulfate (Na2S04) to the virgin leach residues reduced the amount of Ba dissolved to an acceptable level. The used leach residues passed the EP Tox Test for all elements but failed the WET and TCLP for Pb.

Jan 1, 2010

This publication contains four papers presented at a seminar on mine subsidence control held in Pittsburgh, PA, on September 19, 1985. The seminar was designed to keep the mineral industry informed of new technology developed by the Bureau of Mines that permits reliable and accurate prediction of mine subsidence. The papers describe actual field studies undertaken by the Bureau to monitor surface subsidence over longwall panels. Topics discussed include the efects of subsidence on water table levels, the development of subsidence pre calculation methodology suitable for use with the specific lithological conditions of the Pittsburgh coalbed, an engineering comparison of technologies used in surveying for longwall mine subsidence, and a comparison of the process of subsidence over two different longwall panels.

Jan 1, 1985

By W. Hermanson

This report, which covers the period from January 16 to October 21, 1974, describes the work performed in compliance with the requirements of contract no. H0242028 and modifications 1 and 2 thereto. The purpose of the contract was to further reline and modify three of the canopies (shuttle car, loader, and roof drill) which were developed under contract no. H0220031, and to conduct further testing and demonstration of the relined designs. Modifications I and 2 involved conducting further in-mine evaluations of the face. drill and cutter canopies, also developed under contract no. H0220031. In addition to the canopy modifications, the contract involved an evaluation of an operator's seat concept for a shuttle car which was developed for the USBM by another contractor.

Jan 1, 1974

By James J. Dowd

The investigation to evaluate the reserves of coking coal in the United States suitable for the manufacture of metallurgical coke is being made by the Bureau of Mines in three parts: (1) To estimate known (measured plus indicated) recoverable reserves of all coking coal; (2) to upgrade marginal coals through effective preparation; and (3) to study the carbonizing properties of coals and coal blends not now widely used for metallurgical coke making. This is the sixth of a series of reports giving the results of studies by counties under part (1) of the investigation. (See appendix.) This report covers Fayette County, Pa., which comprises the Uniontown and parts of the Brownsville, Connellsville, Donegal, Waynesburg, Masontown, and Confluence, Pa., Morgantown and Bruceton, W. Va., and Accident, Md., quadrangles. (See fig. 1.) A short resume of the chemical and carbonizing properties of the coals ar.9 included. Data on the coal beds in this county were obtained from mining companies, land companies, individual landowners, and other sources of authentic information.

Jan 1, 1951

By J. B. Zadra

Much has been published by various investigators on the use of activated carbon for adsorbing precious metals from cyanide solution and pulp. For the benefit of the reader, a list of these earlier publications appears at the end of this report. The present paper deals only with a process for extracting gold from gold-laden carbon and re-use of the de-adsorbed carbon. At the Getchell mine, Redhouse, Nev., experiments have been in progress for several years concerning the use of activated carbon to adsorb gold from their slime circuit pulp. The experimental work has been successful. Their practice has been to ship the gold-laden carbon to a smelter for treatment, which meant the total loss of the carbon in addition to smelter and freight, charges, all of which proved costly and wasteful.

Jan 1, 1950

By A. T. Iannacchione

Roof-rock instability in advancing sections of underground coal mines is a major contributing factor to accidents resulting in fatalities and injuries. Such roof-rock conditions can also result in loss of production due to additional cleanup time and increased amounts of reject material. The Bureau of Mines is investigating fundamental geologic factors affecting coal mine roof-rock instability in order to develop techniques to predict zones of potential unstable roof-rock. Two distinct directional trends of unstable shale roof-rock in a mine working the Upper Kittanning Coalbed are delineated: one trend is associated with the sandstone-shale transition zone, the other with a fault system. The unstable shale roof-rock associated with the transition zone, a consequence of differential compaction, is comprised of slickensided roof-rock. Whereas, the unstable shale roof-rock associated with the fault system, a consequence of structural deformation of the strata, is comprised of fault planes. These faults, small in comparison to the sandstone-shale transition zone, are difficult to delineate with a standard drilling program. Trends of the transition zone associated with the sedimentary facies change are projected into unmined portions of the coalbed with the aid of exploration core data.

Jan 1, 1981

By D. J. MacDonald

The Bureau of Mines has conducted bench-scale investigations leading to the design of an integrated process for producing reactor-grade zir-conium oxide (Zr02) from zircon sand, which avoids the air pollution, water pollution, fire hazard, and odor problems associated with the hexone-thiocyanate process. The integrated process consists of three steps: production of crude zirconyl sulfate solution, solvent extraction, and production of Zr02 from strip liquor. This report describes the solvent extraction step. Multistage, countercurrent liquid-liquid extraction with a tertiary amine in kerosine was used to separate zirconium from a dilute H2S04 solution containing hafnium and other impurities. Process steps de-scribed include extraction from an aqueous feed solution to form a hafnium-contaminated, zirconium-bearing organic-phase solution, scrubbing to separate zirconium from coextracted hafnium, stripping to transfer hafnium-free zirconium into an aqueous strip liquor, chloride-loading to produce a chloride-bearing organic solution, scrubbing with the chloride-loaded organic solution to remove traces of uranium impur-ity from the zirconium-bearing strip liquor, and regeneration to pre-pare the organic solution for reuse. These steps were performed simul-taneously in steady-state, bench-scale experiments. Zirconium recovery of up to 93 pct was achieved. Results of an economic evaluation are included.

Jan 1, 1984

By C. Melvin Lepper

Microseismic energy is generated when stresses accumulated in rock formations are released in the form of fracturing. The acoustic emissions resulting from these rock fractures and movements are detectable as velocity signals in the earth near the energy source. A Bureau of Mines microseismic system that is capable of detecting the acoustic emissions from pit slope movements is described. The digital circuitry incorporated in the system allows a microprocessor program to immediately calculate and present the location coordinates for the seismic energy source in the mine pit wall. This monitoring system is compact, portable, reliable, and relatively inexpensive and rapidly provides accurate information to the mine operators about the stability of a pit slope.

Jan 1, 1982

By Louis A. Panek

Determining the change of stress in rock based on measurements of the deformation of a drill hole is a procedure that is increasing in popularity. A closely related procedure involves the applicat10n of this principle to determine the existing stresses in a rock medium, by cutting free (core drilling) an annulus containing the drill hole. In this Bureau of Mines report, expressions are derived from which one can calculate the stress ellipsoid--the three-dimensional change of stress, or the existing three-dimensional stress field, as the case may be. Study of these equations shows that the stress components in three dimensions can be determined by measurements in only two drill holes, and yields general principles that are useful in planning an efficient program of drilling and measurement. Procedures are given for calculating the least squares estimates of the stress components and their standard errors, and for evaluating or comparing calculated values by means of standard statistical inferences.

Jan 1, 1966

By Kim B. Shedd

The Bureau of Mines measured fiber dimensions on crocidolites (riebeckite-asbestos and magnesioriebeckite-asbestos) from the world's four crocidolite mining regions. The objective of the study was to determine whether there are measurable morphological differences between crocidolite fibers that correlate with the high reported incidence of mesothelioma in miners and mill employees in the Cape Province of South Africa and Western Australia, as compared with little or no reported incidence of this cancer in the Transvaal Province of South Africa or Bolivia. Fiber dimensions measured with the scanning transmission elec-tron microscope showed that crocidolites from Western Australia and the Cape Province have more thin fibers than crocidolites from Bolivia and the Transvaal Province.

Jan 1, 1985

By M. J. Pazuchanics

This U.S. Bureau of Mines report presents results from an ongoing investigation of the use of adaptive signal discriminating methods to distinguish between cutting coal and cutting mine rock. Bit-cutting forces and tool vibration were measured in the laboratory as a linear-cutting apparatus (LCA) made constant-depth cuts in coal, sandstone, and shale test specimens. A portion of the collected data has been analyzed and some preliminary results are given here. The influence of data bandwidth, data window size, number of signal features, and voting among classifiers on classification performance are noted. Results to date, based on ideal-cutting conditions and simple geologic materials, indicate that of the four classifiers tested there appears to be no single best classifier. Usually, classification accuracy showed slight improvement as the number of features considered for classification increased. The highest classification accuracies were achieved when voting was conducted among classifiers followed by voting among force components.

Jan 1, 1991

By Edward C. Peterson

Recent studies indicate that the United States halt substantial reserves of ilmenite, one of the major titanium minerals. However, the studies showed that sources of rutile, another important source of titanium are limited. This paper summarizes and evaluates results and conclusions reached by the various investigations initiated by the Bureau of Mines and others pertaining to the titanium mineral resources of the Nation. Domestic occurrences of ilmenite that are economically exploitable by present-day beneficiation methods are found in Florida, New Jersey, New York, South Carolina, and Virginia. These deposits are estimated to contain 50.3 million tons of titanium dioxide (TiO2). Occurrences of ilmenite that cannot be processed economically under present technological conditions are found in California, Colorado, Minnesota, Montana, Oklahoma, Oregon, Rhode Island, and Wyoming. These reserves amount to 51.1 million tons of TiO2. Reserves of rutile found in the United States are estimated to be 1.8 to 2.1 million tons of TiO2. Other than occurrences in Florida and South Carolina, rutile is found either in small scattered bodies or in deposits where the mineral cannot be recovered economically by present beneficiation methods.

Jan 1, 1966

By Horace T. Reno

This information circular surveys the iron are industry of the world. It presents a comprehensive statistical record through 1970 of the U.S. iron ore industry and world trade patterns. The supply position of the United States and the other principal industrial countries of the world are summarized; detailed information is given on iron are production, consumption, imports, exports, mine capacities, substitutes, properties, and uses. There is a generalized discussion of the technology of mining and smelting iron ore, with a selected bibliography on the current state of these arts. The circular contains a summary economic account of world iron are resources, and discussions of the structure of the domestic and principal foreign mining industries, iron are mine employment and labor productivity, research and development, legislation, government programs, and strategic factors.

Jan 1, 1973

By R. T. MacMillan

A number of chemical techniques have been applied to manganese ores from three areas of Aroostook County, Maine. Although large tonnages of these ores have been proved, they are low grade, and their exploitation has awaited a suitable beneficiation scheme. As conventional ore-dressing methods had failed to yield satisfactory results, attention was turned to chemical procedures. Leaching with dilute (7-percent) H2S04 extracted over 90 percent of the manganese from ore of the Dudley farm area, consuming 3.8 pounds of acid per pound of manganese extracted. Ores from the Littleton Ridge and Maple Mountain-Hovey Mountain areas were less amenable to this treatment, yielding approximately 80 and 60 percent of their Mn content, respectively. To increase the percentage extraction of manganese in the latter two ores, a number of factors were varied, including (1) acid concentration in the extracting solution, (2) ratio of acid to Mn in the slurry, and (3) preliminary heat treatment of the ore with a reducing agent. Other acids, including HNO3, HC1, and H2SO3, were tried also; however, no significant improvements in the Mn leached from Maple Mountain-Hovey Mountain ore were made. The manganese extraction of Littleton Ridge ore was raised to 90 percent by providing 9 to 11 pounds of HNO3 per pound of Mn in the ore.

Jan 1, 1954

By E. P. Youngman

This paper presents one of a series of digests of foreign mining legislation and court decisions that is being prepared in advance of a general report relative, to the rights of American citizens to explore for minerals and to own and operate mines in various foreign countries. This interpretation of the mining laws of British Guiana has been prepared from the best available sources in Washington and is, released subject to amplification and correction, if necessary, by United States foreign-service officials. INTRODUCTION The sources of information available in the preparation of this paper are the following: 1. The Crown lands ordinance, No. 32 of 1903, September 26, 1903.

Jan 1, 1934