Search Documents

By Kevin Malone

Mercury, or quicksilver as it is often called, has many applications in modern technology. Used principally in electrical apparatus, industrial contol instruments, insecticides and fungicides, electrolytic preparation of chlorine and caustic soda, chemical processes, pharmaceuticals, and dental preparations, the liquid metal has unusual properties that make it a preferred material for many industrial uses. United States consumption of mercury during the past 40 years shows a rising trend. In all except 4 years, U.S. production has been less than the domestic requirement, and imports, principally from Spain, Italy, and Mexico, have supplied most of the deficit. After World War II, domestic output decreased rapidly until 1950, when it was the lowest in the 100 years covered by production records. Higher mercury prices since 1950 have reversed the decline in domestic output and reduced the gap between U.S. production and consumption. Domestic output in 1958 was the highest in peacetime since 1883; however, the nation still imported 28 percent of its mercury requirements from 1950 to 1960 the price of mercury was high as a result of industrial applications of the mercury cell, the impact of the cold war and the Korean war, and the Government stockpiling program. The stockpiling program, in effect, put a floor under mercury prices even though only 9,428 flasks of domestic mercury went into the stockpile under the original program which ran from July 1954 to December 31, 1957. Under an extension of the program, an additional 17,463 flasks was purchased.

Jan 1, 1962

By D. C. Dahlin

To identify and characterize potential domestic chromium resources, the Bureau of Mines investigated podifom chromite deposits along the Border Ranges Fault in southern Alaska. Part 1 of this two-part report describes an extensive field investigation and preliminary resource evaluation studies by the Bureau's Alaska Field Operations Center. This paper, part 2, describes the mineralogy of 38 samples that were collected from low-grade deposits in the Chugach Mountains, on the Kenai Peninsula, and on Kodiak Island, and presents the results of laboratory batch beneficiation tests designed to concentrate the chromite. The samples are peridotites and chromites that consist primarily of variable amounts of chromite, olivine, and serpentine. They were beneficiated by a sequence of grinding, sizing, and gravity concentration operations. Twenty-four high-chromium or marginal high-chromium chromite concentrates, six high-iron or marginal high-iron chromite concentrates, and five submarginal concentrates were produced with chromium recoveries that ranged from 37 to 95 pct. Three very low-grade samples were not beneficiated. These results indicate that several of the de- posits may be significant chromium resources, Potential precious metals association with the chromite was also investigated. Analysis of these samples indicates that the chromite deposits are not good platinum sources.

Jan 1, 1985

By Russell J. Foster

Public awareness of, and involvement in, recycling has increased significantly in recent years. Nevertheless, recycling is generally perceived as a new development, and is familiar only in the context of municipal solid waste management. The actual magnitude and scope of metals recycling in the United States have gone virtually unnoticed. Over time, both the quantitative and qualitative aspects of secondary metals recovery and reuse have changed substantially, while the attendant regulations have become increasingly stringent. This U.S. Bureau of Mines report examines trends and developments in major metal demand and recycling, and analyzes the possible impacts of regulations with regard to recycling activities.

Jan 1, 1994

By Ellsworth Y. Dougherty, Edwards F. Fitzhugh

"INTRODUCTION During the summer of 1945 the Bureau of Mines made approximately 200 miles of reconnaissance magnetic surveys in north-central Mirnesota. The survey started near the western end of the Mesabi Iron Range and extended into the area to the southwest, west, and northwest and also southward to the-northern limits of the Cuyuna Iron Range. The purpose of the survey was to data to assist exploration for iron ore in the region through:1. Supplying a relatively unit form network of traverses, by which and future surveys of localities in the urea ray be correlated. Suggesting localities in which more detailed magnetic surveys may be justified, and, Disclosing localities in which there is lass hope of obtaining significant results from further magnetic surveys.The instrument used was a Hotchkiss Superdip, and traverses for calibration and comparison were run with a Schmidt-type magnetometer. Field observations and work directly related thereto were carried out under contract by E. J. Lang-year Co., Minneapolis. Engineers of the Bureau of Mines planned, directed, and reviewed the survey."

Aug 1, 1946

By R. S. Dean

"Applied Mineral Physics, by R. S. Dean.- This is an introduction to the seven papers that follow. It discusses the practical aspects of mineral physics and outlines the theo¬retical viewpoint underlying the investigations reported herein.Explosive Shattering as a Possible Economical Method of Ore Presentation By John Gross and C. E. Wood. - It is shown that explosion shattering by impact is favored by large charges and by low ratio of water to charge. For 400-gram charges of dolomite crushed through 48 mesh the steam costs are less than 5 cents per ton of dolomite obtained. This is within the range of present steam costs for ball-milling dolomite.Electrical Properties of Minersl Aggergates I. Natural and Artificial Aggregates Crystallized Lead Sulphide By R.S. Dean and John Koster - This paper deals with the electrical properties of natural and synthetic galena. It is shown that massive crystalline galena has a normal positive temperature coefficient of resistance, whereas fine-grained steel galena has a negative temperature coefficient, the curve R v. T being exponential in form. That steel galena behaves somewhat like a leaky condenser is indicated by ballistic and alternating-current bridge measurements. In determining the cause of the erratic results of alternating-current resistance measurements it was observed that the measured re¬sistance was a function of the current through the specimen. The direct-current resistance was found to be proportional to the square of a superimposed radio-frequency current and independent of the frequency.The influence of grain size or the amount of metallic interface on the voltage-current characteristics at various temperatures on synthetic galena pastilles was studied. It is proved that the volts v. amperes curves are linear for all sizes and temperatures, that they have an intercept which is apparently a linear function of the temperature, and that their slopes are exponential functions of the temperature and give rise to a negative temperature coefficient of resistance.Apparatus for determing the Magnetic Constants of Mineral Powders by V,H, Gottschalk,and C. W. Davis.- A modified isthmus permeameter having a spark-suppressed primary and a multiplier in the secondary circuit to regulate the effect of capsules functioning as a twin isthmus is used to obtain quantitative data and normal induction and hystersis curves from small amounts of powdered material at fields surpassing 3.000 oersteds. Data and curves are given to demonstrate the calibration of the apparatus and the reproducibility of its results. Applications and limitations of the apparatus are noted.Magnetization Curves for Magnetite Poeders by V. H. Gottschalk and F. S. Wartman.- This paper gives measurements on four lots of purified and analyzed magnetites in mixed fractions with especial reference to the variation of permeability with grain size and with dilution by an inert material."

Feb 1, 1935

By A. E. Petersen

To reduce U.S. dependence on imports of titanium, the U.S. Bureau of Mines has investigated the recovery of titanium from perovskite (CaTi03). Domestic perovskite deposits represent a significant, but untapped, titanium resource. An acid sulfation method was developed that will extract about 97 pct of the titanium and the columbium and 70 to 90 pct of the rare-earth byproducts from perovskite concentrates. A flow-sheet for recovering titanium as pigment-grade titanium dioxide (Ti02) is discussed. Test work performed in developing each unit operation is described. The first three unit operations have been demonstrated using laboratory-scale continuous methods of operation: acid sulfation of perovskite concentrates, leaching sulfation residue to dissolve metal values, and precipitation of titanium oxysulfate monohydrate (TiOS04?HP) from the resulting leach flltrate. Batch testing of other unit operations was performed: TiOS04?H20 redissolution and iron reduction, precipitation of Ti02 by hydrolysis, and regenerating recoverable acid with rare-earth byproduct recovery. Cost evaluation results are provided, indicating that processing perovskite concentrates by acid sulfation may be an economically viable means of producing Ti02.

Jan 1, 2010

The following is a Maintainability Design Checklist for coal mining equipment. The purpose of the checklist is to provide a summary of design review points for the maintainability assessment of new or existing underground equipment. It specifically focuses on the identification of equipment design features, tasks, or procedures that impact equipment downtime, repair costs, labor hours and maintainer skill level requirements. Some checklist points are general in nature. The checklist was designed to be used across all categories of underground equipment. The intent is to draw attention to design features and maintenance procedures that will increase maintainability requirements. You are encouraged to adapt this checklist to site specific or machine specific requirements by: Inserting specific performance criteria for various categories of maintenance tasks. For example; all hydraulic lines on a shuttle car should be replaceable in 15 minutes or 25 minutes, etc. Adding or deleting checklist items for different categories of equipment. You would include environmental control equipment, for example, on face equipment and not on shuttle cars or man trips. Adding additional checklist items based on site or equipment specific maintenance histories or experience, company maintenance standards, or other factors.

Jan 1, 2000

This section presents highlights of world economic and mineral industry performance in 1982, a year characterized by continued recession, and selected 1983 forecasts of economic indicators of importance to the mineral industry, some of which indicate a modest improvement in the economies of the United States and Western Europe. The U.S. Economy in 1982 In 1982 U.S. gross national product (GNP) in current dollars increased at a rate of 4 percent, but GNP adjusted for inflation (real GNP) declined at a rate of 1.8 percent. Yearend 1982 real GNP was at roughly the same level as in 1980 (table 1). Thus no growth in real terms had taken place in the United States during the 1980-82 period.

Jan 1, 1983

By Peter Grandone

Steel and iron pipe lined with cement to protect it against corrosion has been used in the municipal water systems of the New England States since about 1870. In most recent years, the petroleum industry adopted cement-lined pipe to forestall corrosion, particularly in those areas where large quantities of corrosive brines and hydrogen sulfide are associated with the oil produced. Many of the oil companies had on hand large quantities of corroded pipe, normally disposed of as scrap, which could be cleaned, lined with cement, and returned to service. It was soon learned that after the so-called scrap pipe was lined with cement much of it could serve fully as well as new cement-lined pipe. The demand for lining used pipe with cement resulted in the establishment of several processing, plants in the Mid-Continent oil-producing area. Today six cement-lining plants serve the areas three in Oklahoma and one each in Kansas, Texas, and Illinois. All of these plants have lined large quantities of used pipe for the brine-disposal systems of western Kansas, Illinois, and east Texas and also for the operators of water-flooding projects in northeastern Oklahoma and southeastern Kansas, where large quantities of brine and fresh water are being injected into the oil-bearing formations as a secondary oil-recovery method. Since war demands during the past 2 years have created an acute shortage of steel, the need of reclaiming used pipe for the expansion of oil-producing operations has become more evident than ever before. Thus the new industry (about 6 years old) - lining used pipe with cement - is saving large quantities of steel at a critical time by reclaiming used pipe and preventing further- corrosion.

Jan 1, 1945

By D. E. Wolfson

As a part of its overall program of coal carbonization, the Bureau of Mines is studying the coking properties of coals that may be used for metallurgical purposes. The objectives of this study were given in detail in a previous report The inherent suitability of coal for metallurgical purposes depends primarily on (1) chemical composition, (2) preparation characteristics, and (3) carbonization behavior. The first two factors, Be well as the amount of available reserves, are considered in selecting coals for carbonization tests. The selection of coal beds in Harlan County, Ky., for coking tests was based, in part, on recent studies of coal reserves by Wallace,3/ who estimated the recoverable reserves in beds 28 inches or more thick, in tons, as follows:

Jan 1, 1956

By Donald W. Mitchell

Studies were made in the Bureau of Mines Experimental coal mine to evaluate the effectiveness of a few extinguishing agents and techniques for controlling a fire on a simulated mining machine. The investigation showed that water containing an alkali-metal salt or a surface-active (wetting) agent was more effective than water alone. For close attack, fog applications was the most effective technique studied; high rates of agent application controlled the fire more quickly than low rates. The ability to control the fire increased as the distance of attack decreased. Dry powders controlled the fire when applied by shovel but not when applied airborne by rock-dust distributor or by hand fire extinguishers. Dry alkali-metal salt powders (potassium and sodium bicarbonates and sodium tetraborate) quenched the fire more readily than limestone dust. In each instance the finer powder, the greater its effectiveness. In an open ventilated entry, smoke and hot gases backed against the air currents. An airspeed of 230 feet per minute was required to permit approach to within 10 feet of the fire. At lower airspeeds, approach could be made by extending the brattice across the bottom two-thirds of the entry, by pushing the smoke ahead with water sprays, or by discharging dust from a rock-dust distributor. In a dead-end entry, the fire was approached to within 30 feet by coursing fresh air along an airtight line brattice; however, it was safer, easier, and less time-consuming to attack the fire from a fresh-air base 100 feet away with a solid stream or by high-expansion foam; the latter method was more effective.

Jan 1, 1961

By John C. Edwards

A fire location computational model was developed by the U.S. Bureau of Mines. The model can determine all the possible paths in a mine that smoke can travel from a fixed fire source to a smoke detector. The associated FORTRAN computer program can be utilized to determine the minimum travel time from a source fire to a smoke detector. The difference in travel time from an isolated fire source to two or more detectors can be used to isolate those airways in which the source fire is located.

Jan 1, 1990

The investigations reported herein comprise preliminary studies to evaluate large scale mining systems adaptable to the thicker oil shale deposits in the deeper central portion of the Piceance Creek Basin. The studies include an evaluation of the geology, hydrology and resources of the Basin., evaluation of a potential prototype mine site, synthesis of rock mechanics data on Green River Formation oil shale, selection and preliminary design and cost evaluation of six potential mining systems and a ranking analysis to aid in selecting the most promising system. Results of the ranking analysis indicate the following four systems to be most promising for large scale underground oil shale mining: - Chamber and pillar (using spent shale backfill) - Sublevel stoping with spent shale backfill - Sublevel stoping with full subsidence - Block caving with LHD's Recommendations for phase II are to investigate the above systems in greater detail, refine present cost data, and perform economic evaluations of oil shale mining using these systems.

Jan 1, 1975

By Roy E. Williams

1. The major sources of heavy metal ions in wastewaters of the Coeur d'Alene Mining District are effluents from metallurgical processing plants. Effluents from mine operations provide a secondary source for heavy metal ions. Based on data analyzed by the Federal Water Quality Administration, mercury and arsenic are escaping from some mill waste ponds, but they are in the suspended phase. 2. Metallurgical process effluents are combined with mine waste effluents in tailings ponds, consequently, the quality of the tailings pond decant water is highly degraded. The major effect of combining metallurgical process effluents with mill wastes is a drastic change of pH in the tailings pond. This chance may be an increase or a decrease depending on the metallurgical process. The effluent from an electrolytic antimony plant drastically increases the pH in the tailings pond permitting the removal in solution of antimony via the pond decant system. The addition of low pH effluents to the tailings ponds results in a net decrease in pH which makes lead, zinc, cadmium, and copper more soluble, thereby permitting their removal from the pond via the decant system.

Jan 1, 2011

By F. R. Lee

[WHEN the Bureau of Mines was established in July 1910, one of the problems immediately attacked by the new organization was the development of standard, for the design and testing of electrical equipment that could be used without fear of initiating fires and explosions in underground coal mules. Research and investigation by Bureau personnel, supplemented by the published results of similar work by European mining authorities, led to the establishment of standards or "schedules." which guide manufacturers in the design of many types of electrically operated machines and devices used in. underground coal Mining. By issuing these standards, Bureau personnel establish the requirements to be met by such equipment before it tan be approved by the Bureau of Mines as permissible for use in gassy coal mines. Every 2 years the Bureau of Mines publishes a list of equipment that leas been accepted as approved or permissible during the preceding 2 calendar years. This is done to inform the mining industry of the availability of the latest equipment for safe use underground.]

Jan 1, 1964

By Glen C. Reed

"The Avon mica district of Latah County, Idaho, is situated on a heavily forested spur of the Thatuna Range at an average altitude of 4,000 feet. The nearest rail connection is at Avon, a small farming settlement 7 miles to the south. The main supply point is Moscow, Idaho, which is 35 miles by graveled and graded county roads from Avon.Discovery of mica-bearing pegmatites in 1885 was followed in 1888 by exploitation of several outcrop deposits. Although factual data are unavailable, past production appears to have been well in excess of $100,000. Recent production (September 191 to April 1945) amounted to 65,824.78 pounds of trimmed sheet mica and 33,294.17 pounds of punch mica having a total gross value of $434,298.The several properties of the district are variously owned by estates, individuals, and the State. When active, all wore under lease or sublease to individual operators.The deposits are in an area of pre-Cambrian schists adjacent to a small granitic outlier of the Idaho batholith. The pegmatites are nearly concordant in dip and strike to the foliation of the enclosing schists. The more persistent bodies are usually tabular, lenticular, or pegmatite. Individual dikes range in length from 10 feet or less to 300 feet.The recoverable crude mica content of the pegmatites ranges downward from a maximum of 115 pounds per ton of pegmatite mined. Material discarded in rifting and trimming operations further reduces recovery to a maximum of 5 pounds per ton -of pegmatite mined. The average recoverable sheet content of the 'recently operated .deposit is estimated at 2 pounds per ton of pegmatite -mined. Available data indicate that about 21 percent of the district's recent production of trimmed sheet mica has been ""Group A"" material suitable for exacting condenser requirements. A few of the dikes contain local concentrations of beryl.Reserves of the three known major deposits of the district are estimated at about 600 to 1,000 tons of combined ""indicated"" and ""inferred"" crude block mica. One of these deposits is inferred to contain between 150 and 450 tons of beryl.It is believed that those mica reserves are minable only under a cost-market price ratio similar to that established during 1943 and 1944. A small part of the reserves can be ""high-graded"" under the present price structure. Profitable recovery of the beryl would require a market price four to five times that paid in 1944.Preliminary examination of the Avon mica district was made by the Bureau of Mines in the summer and fall of 1942. A study of the Muscovite mine and a brief reconnaissance of the surrounding district led the Bureau to recommend that the district be explored by angle-dozer trenching."

Jul 1, 1946

By W. Hermanson

This report presents the results of a task to complete a final design of a remote controlled hi-roof bolting machine for high roof areas in coal mines. The project was begun by visiting several coal mines to become familiar with roof fall areas. Several machine concepts were generated and presented to the design committee for criticism. A preliminary design was completed, as covered by this report. A Final Design and Final Report will be issued incorporating the committee comments at the Preliminary Design review and comments received concerning this Preliminary Design Report.

Jan 1, 1979

By Alexander May

The U.S. Bureau of Mines conducted studies to determine if phosphate slag stockpiles at Tennessee Valley Authority's National Fertilizer Development Center were hazardous materials. The stockpiles were not hazardous materials as determined by Environmental Protection Agency (EPA) extraction procedure (EP) toxicity test. Radium-226 concentration was 28.7 pCi/g in slag and 2.1 pCi/g in background material. Radium-226 was not leached from the slag. Fluoride concentration was 3.87 pct in slag, 0.18 pct in subsurface material under slag, and 0.08 pct in the background. Slag material permeability was 1.65 x 10-3 cm/s, and subsurface material permeability was 3.24 x 10-6 cm/s. Rain water, trapped in a depression on top of the east slag stockpile, became seepage water at the base of the stockpile. Concentrations of EPA toxic elements in seepage water were much less than concentrations from an EPA EP toxicity test on the slag. Twelve elements-Na, Mg, Ca, Sr, Ba, Cr, Mn, Co, Cu, Cd, AI, and P-had higher concentrations in seepage water than in rain water on top of the slag stockpiles, or in creek water adjacent to stockpile bases, indicating that they were leached from slag stockpiles.

Jan 1, 1990

By M. D. Aldridge

The results of designing, constructing, installing and operating a ventilation monitoring system throughout an entire commercial coal mine is presented. Measured parameters were airflow, methane, carbon monoxide, temperature, relative humidity and differential pressure. A central computer provided for automatic system operation. Preliminary tests of two remotely controlled ventilation regulators were performed in conjunction with the monitoring system.

Jan 1, 1977

Construction workers may be exposed to hazardous dust containing crystalline silica during site preparation when drilling systems are used. The National Institute for Occupational Safety and Health (NIOSH) found that drill dust could be decreased by using wet or dry dust reduction engineering controls, enclosed cabs, and implementing a dust control program.

Jan 1, 2009