Search Documents

By Jerry B. F. Champlin

NIOSHAn accelerated testing procedure developed by the Bureau of Mines for evaluating commercially available corrosion inhibitors is described. Ultra-sonic agitation of the corrodent solutions and the hot-finished mild steel test coupons was used to evaluate the effects of several variables on the effectiveness of two corrosion inhibitors. Small changes in the weight of the test coupons in both controlled and inhibited corrodents, before and after exposure, affected the precision and accuracy of the results. Minute amounts of oxygen in the systems were found to be causing the relatively large deviations in the corrosion developed in the controlled tests. Microscopic examination of the test coupons revealed that both surface preparation and internal strains resulting from fabrication methods materially affect corrosion behavior.

Jan 1, 1965

By Merwin H. Howes

In constructing the NORAD Combat Operations Center, controlled blasting techniques were employed to achieve smooth walls and to avoid shattering the rock beyond excavation lines. Extraordinary measures were taken to stabilize the rock to permanently preserve the openings. Rock stabilization was accomplished by means of reinforced concrete and gunite linings, rock boltings, installation of chain-link fabric, and epoxy resin and cement grouting. A particular zone of weakness at B vital location was supported by exceptionally thick reinforced concrete lining, rock bolts, and cement grout.

Jan 1, 1966

By R. E. Heithecker, D. B. Taliaferro

"INTRODUCTION Recovery of core specimens from subsurface formations and their subsequent analysis are important aids in efficient development and operation of oil and gas fields. Gore specimens first were obtained mainly for the geologic information they revealed; now they are analyzed to determine many of the physical characteristics and conditions of the subsurface formations as well. Cores recovered from the producing formations may be analyzed for porosity, permeability, oil content, ""connate"" water content, and other physical and chemical properties of the formation, all to the end of furnishing enough data for making reliable estimates of the quantity and avail¬ability of oil and as within a reservoir and in devising efficient means for their withdrawal.Examination of bottom-hole samples of oil gives valuable information concerning the amount of gas in solution in the oil within the reservoir and the resultant shrinkage of the oil when the gas is released. Producing characteristics of reservoirs nay be determined by means of subsurface pressure and temperature gages and measurements male at the wellhead; however, unless reliable core analyses are available, these data have only limited use in any quantitative study of reserves. In such a study the quantity of oil, gas, and water contained in a unit volume of the reservoir formation is extremely important. Although reliable methods of analyzing cores have been developed and the data thus obtained are valuable, their applications become more limited or reservoirs at higher temperatures and pressures are discovered. This condition results almost entirely from the fact that in recovering a core from a formation of high pressure and temperature by present methods a large part of the fluid content of the core is lost or contaminated to an unknown extent. For a number of years most petroleum engineers have held that if this loss and contamination of the fluid content of a core were eliminated, the value of core analyses would be increased greatly."

Nov 1, 1939

By John C. Machisak

The Nation's mining and quarrying industries have again met the annual challenge to their ingenuity--that of reducing disabling work injuries among their employees. The effectiveness of management in facing this problem and in meeting this responsibility is evident from the results of the 1961 National Safety Competition. Three hundred ninety-three or 45.3 percent of the mines and quarries participating in the competition established a new record number of participants operating throughout the competition year without a disabling work injury. Another record established in the 1961 contest was the number of participants (868) enrolled in the competition. This annual safety competition was begun in 1925 and is conducted by the Bureau of Mines, U.S. Department of the Interior. It provides for six bronze Sentinels of safety trophies which are awarded each year to the winning participant in each group. Since its inception, the competition has exerted a strong influence in the field of safety promotion. The statistical record of its accomplishments over the years gives strong support to the theory that well-organized and well- administered safety programs are effective tools to be used to reduce the number of disabling work injuries. It stimulates and holds the interest of employees and management in accident prevention. Because of this, mines and quarries participating in the contest have a more favorable safety record than those operations not enrolled.

Jan 1, 1963

By D. W. Dareing

Multiple branch wellbores and horizontal holes, when applied to deep lying ore bodies, have the potential of significantly reducing well costs by reducing total footage drilled per acre of well pattern. In addition, horizontal holes may increase sweep efficiency. Well completion is a major problem. They must be cased to contain leaching solutions within the underground portion of the production loop. Several drilling and completion concepts are given and evaluated in the report. Our evaluation shows that there is economic incentive to further develop these concepts for field application to ore bodies 1,500 feet. Multiple branch concepts are the most attractive. They can reduce well costs by as much as 30° when applied to 2,000 feet ore body depths (44%, at 5,000 feet) and can accommodate a lamer pump than conventional vertical wells. We recommend this concept be developed further to accommodate either dual or triple branches.

Jan 1, 1980

As fulfillment of the requirements of Contract H0387019 for the United States Department of the Interior, Bureau of Mines, a complete field kit, for performing on-site determinations of individual employee Time Weighted Average (TWA) exposures to nitrogen dioxide (NO2) and nitric oxide (NO), has been developed by MDA Scientific, Inc. This report provides background information and experimental data validating the use of this kit with confidence to ? 10 percent accuracy.

Jan 1, 1981

By D. J. Bauer

The Bureau of Mines has conducted extensive studies on the recovery of alumina from kaolinitic clay by a HCI leaching-HCI sparging process. The current study reports a modification of the process, which involves a double-leaching system. The first leach of the calcined clay is made at as high a HCI acid strength as possible so that the dissolution of aluminum chloride hexahydrate (AlCI3*6H20) is suppressed, Most of the impurities, but very little aluminum, are soluble in the strong acid. After liquid-solid separation and washing, the solids are leached with recycled weak HCI, which dissolves the AICI3'6H2O. The pregnant liquor is separated from the gangue, and AICI3'6H2O is crystallized from solu-tion by injecting HCI gas. A proposed flowsheet is presented, and the effect of bleedstream size on AlC13'6H20 purity is discussed.

Jan 1, 1984

By Arnold B. Hubbard

This report presents a hydrogenolysis study undertaken to obtain information on the constitution of the kerogen or organic material in Colorado oil shale and to determine some of the properties of the hydrogenolysis products. The high yield of hydrogenolysis products was separated, so far as possible, into type compounds; a number were identified. The results thus obtained were used as a basis for proposing the possible existence of certain structures in kerogen. To the authors' knowledge, few or no hydrogenolysis studies have been made of Colorado oil-shale kerogen by others. However, this method has been used in studying the constitution of coal. In general, the coal studies involved treating pulverized coal at different temperatures and hydrogen pressures with different catalysts. In some instances different solvents were used during the treatments.

Jan 1, 1959

By Arnold B. Hubbard

A thermal decomposition study of the kerogen in three Colorado oil shales was made at different temperatures by heating the shales in the absence of oxygen at atmospheric pressure and measuring the decomposition products (gas, oil, and bitumen) formed. From these data the specific reaction rates, "k", for the thermal decomposition of kerogen were determined for each temperature studied, making it possible to calculate the time required to accomplish a given amount of decomposition within the temperature range. The influence of temperature on reaction rates was presented by plotting the data according to the Arrhenius equation, thus providing a means of estimating the values of "k" for any temperature within the range of this study. It was found that the specific reaction rates for the thermal decomposition of the kerogen in the three sampler were comparatively equal at corresponding temperatures.

Jan 1, 1950

By R. F. Stewart

A key step in changing coals to fluid fuels and chemicals is the conversion of coal to synthesis gas by gasification with steam and oxygen. As oxygen represents one of the largest single expenses in gasification, its cost is a vital factor in the economy of the process. At present, the most economical method for producing tonnage oxygen is by the conventional rectification of liquefied air. Several alternate methods have been proposed for producing oxygen from air: (1) methods based on physical or chemical sorption of oxygen from air by liquids or solids or (2) the oxidation of certain inorganic com-pounds to higher oxides unstable at higher temperature levels. Economic limitations are discussed by which these methods may be evaluated. Chelated metals of the salcomine type are promising chemical sorbents of oxygen from air. This report covers a study of the reversible sorption of oxygen by salcomine and other chelates. The presence of water in the salcomine structure was verified; it is the loss of this water that causes slow deterioration of salcomine during cycling.

Jan 1, 1959

By Paul E. Bennett, James S. Browning, Thomas L. McVay

Continuous 1.0- to 1.5 - ton - per - hour pilot plant flotation tests were made to determine the technical and economic feasibility of recovering beryl from flotation tailing being produced at the spodumene concentrator of the Foote Mineral Company , Kings Mountain , N.C. Best results were obtained when using an acid circuit and amine - type cationic reagents to float a bulk beryl - feldspar concentrate and then selectively floating the beryl away from the feldspar , using a petroleum sulfonate collector . About 77 percent of the beryllium in the pilot plant feed was recovered in a concentrate containing 6.42 percent BeO . The capital cost of an integrated flotation plant capable of treating 500 dry tons of spodumene mill tailing per day for recovery of beryl and feldspar is estimated at $ 210,000 . Indicated direct operating costs for the plant were $ 1.52 per ton of dry spodumene flotation tailing treated . This approximated the value of beryl recovered , but potential profits of about the same magnitude lie in concurrent recovery of marketable spodumene and feldspar byproducts .

Jan 1, 1964

By P. L. Sibrell

Previous research by the U.S. Bureau of Mines has shown that autoclave cyanide leaching of used automobile exhaust catalysts for recovery of platinum-group metals (PGM) is technically feasible. The purpose of this work was to investigate the chemistry of the dissolution of PGM in cyanide solutions in more detail. Where possible, samples of pure, elemental PGM powders or foils were used instead of automobile exhaust catalysts, because of their greater purity. Ultraviolet spectra revealed that Pt and Pd were solubilized as the square planar tetracyanometallate (II) complexes, while Rh was solubilized as the octahedral hexacyanorhodate (III) complex. This explained the poor recovery of Rh from solution by carbon adsorption, solvent extraction, and ion exchange observed in earlier research, because of the higher anionic charge and size of the octahedral complex. Leaching rate studies showed that the rate of solubilization was greatest for Pd, followed by Pt and Rh. Although the rate of chemical reaction was the controlling step for the dissolution of elemental Pt and Rh samples, the rate of pore diffusion was rate limiting for PGM in catalyst samples.

Jan 1, 2010

By Geoffrey G. Huggins

Discussions are presented of the three phases of the noise reduction program on flight-type coal conveyors. The three phases are identification of noise sources, evaluation of potential noise reduction concepts, and implementation of noise reduction which is intended to reduce conveyor noise to less than 90 dB(A) in the underground mining environment. The major noise sources are impacts of the chain on the tail roller and on the top and bottom decks. A total noise reduction of 11 dB(A) was achieved by using techniques which are applicable to retrofit. These are a vibration isolated tail roller and an isolated wear strip on the return deck. A theoretical model of isolation provided by the isolated tail roller is developed. Appendices are presented which contain information on other potential concepts and additional data generated.

Jan 1, 1976

By S. H. Lorain

Tin mining on Seward Peninsula, Alaska, has been intermittently active since the early 1900's. Most of the recorded production (over 2,200 short tons of metallic tin) has been obtained from placer deposits, but recent production also has resulted from development of lode deposits associated with intrusive rocks occurring in the western part of the peninsula. Generally, the lode deposits containing tin minerals (principally cassiterite) are found in dikes, in granite masses, and in silicate zones in limestone overlying the granite. Both the placer and lode deposits have been of considerable strategic interest to the Government because of the almost total absence of a domestic supply of tin. The most important tin-lode deposit discovered to date is in the Cassiterite dike at the Lost River mine, on Cassiterite Creek about 85 miles northwest of Nome. This highly altered, rhyolite porphyry dike averages 12 feet in thickness, strikes N. 75° to 85° E., and dips steeply to the south; it can be traced on the surface for about 8,000 feet. Throughout its explored length of about 2,200 feet the dike everywhere contains some tin and tungsten in veinlets and disseminations; economic concentration of the are minerals, however, is confined to definite shoots. The ore minerals include cassiterite, stannite, hulsite, paigeite, wolframite, scheelite, and base-metal sulfides; gangue minerals include fluorite, boron silicates, and lithium-bearing minerals. Some ore minerals also occur in the numerous other dikes and in the granite and intruded limestone in and adjacent to the mine.

Jan 1, 1958

By Sidney A. Suhler

A field operable, breadboard model, borehole radar was developed for the detection of hazardous geological anomalies in and above a coal seam in advance of mining. A four-inch diameter downhole probe was fabricated and tested in several environments. The radar transmitter was also employed in a cross-hole or through transmission mode to determine natural geotechnical and man-made conditions between boreholes. Sensitivity to underground conditions in both modes of operation were indicated.

Jan 1, 1978

Air pollution control regulation$ already implemented or being considered for implementation require substantial investment of capital to remove the sulfur oxides from copper, lead, and zinc smelter gases. There will be an attendant increase in production costs and possibly an associated increase in the price of these metals to the consumer. The total investment and any resultant metal price increase will depend upon the control regulations that ultimately will be adopted by the individual States. Controversy has arisen between the metals industry and governmental control agencies regarding the status of stack gas desulfurization technology and the ability of industry to control sulfur oxide emissions to the degree proposed by some of the more stringent regulations currently under consideration. This paper evaluates the problems involved in achieving various degrees of control over smelter sulfur oxide emissions and the technology available to accomplish the task of assuring clean air. The estimated cost of compliance is reviewed for the copper, zinc, and lead industries, but principal at tent ion is given to the copper situation.

Jan 1, 1971

By John L. Miller

The synthetic fluormicas may be divided on the basis of silicon content into tetrasilicic, trisilicic, and disilicic. Properties of lead and barium disilicic fluormicas were determined to characterize these two representative members of the disilicic group. Properties described include unit-cell parameters from X-ray diffraction, optical data, chemical composition, density, melting point, and mechanical and dielectric properties. Both the lead and the barium micas were typically monoclinic; neither was sufficiently cleavable to yield usable mica splittings. Both yielded polycrystalline, machinable ceramics with excellent mechanical and dielectric properties.

Jan 1, 1963

By J. L. Holman

The Bureau of Mines is conducting research to recover strategic and critical metals such as Ni, Co, and Cr from mixed contaminated super-alloy scrap. One approach being studied involves melt refining of superalloy scrap to produce anodes for electrolytic deposition of Ni-Co alloy. This melt refining of superalloy turnings is described based on melt-oxidation and oxidation-carburization experiments, using roasted superalloy grinding sludge to supply the 0 needed to oxidize Cr and other readily oxidized elements to the slag. Controlled melt-carburization subsequent to oxidation improved the metal phase recovery of Ni and Co to well over 90 pct and decreased electrolytic solubility of Cr, Mo, and W by carbide formation. Electrolytic refining experiments were conducted using a controlled-potential mode (preset cathode potential). Data show effects of Fe and Cr impurities, cation concentration, electrolyte pH, S04-Cl electrolyte ratio, temperature, cathode potential, and cation-selective membrane use on current efficiency, current density, and deposit composition. Disposition of Ni, Co, Cr, MO, W, and Fe is compared for melt-oxidized versus oxidized-plus-carburized anodes. Deposits containing >97 pct Ni + Co (major impurity Fe) have been routinely obtained from scrap anodes. Research is continuing to improve deposit quality in sustained deposition and to recover Cr and other metals from refining slags and anode sludges.

Jan 1, 1986

By S. H. Ash

THIS REPORT covers the third in a series of five projects into which the Conowingo tunnel system has been divided for geographical and practical reasons. It outlines the work constituting Project No.3 that consists principally of the following: (a) To sink the No. 15 shaft and extend the Alden, Sugar Notch, Baltimore No.2, and Laflin shafts from their present depths to tunnel level; (b) to drive a tunnel off these shafts to connect with the western end of the tunnel in Project No.1 (Lackawanna) and to a point 1 mile south of the No. 15 shaft; (c) to construct an emergency pumping plant at the No. 15 shaft, complete with 3 centrifugal pumps of 200-cubic-foot-per-second (c. f. s.) capacity each, and a discharge-water shaft and a discharge tunnel for conducting the water from the pumping plant into the Susquehanna River; and (d) to construct a lateral tunnel 1 mile long off the main tunnel in the vicinity of the No. 15 shaft, to be known as the Wyoming lateral. The project, as outlined, is a self-contained drainage unit that will permit unwatering inundated mines and safeguarding active mines in the Wyoming Basin of the Northern field and also will handle the water in the Lackawanna Basin, thus permitting the temporary pumping plant provided in Project No.1 to be discontinued. The pumps installed in the temporary pumping plant provided in Project No.1 can then be moved to the emergency pumping plants recommended in Projects Nos. 2 and 3, to be installed as the third or standby unit.

Jan 1, 1955

By G. L. Oldright

In the first paper of this series (R. 1. 4333) on the cooperative work with the Eagle-Pitcher Mining & Smelting Co., changes in the nature of the sinter feed were measured by corresponding changes in the retorting temperatures necessary to distill zinc at the best rates; the firing schedules summarized such changes. In this paper, third of the series, are noted same of the changes in practice that were brought about by the need to treat more fused, glassy, and "hard" sinter, as the operators qualify it. Losses of uncondensed zinc were increased by adding zinc-bearing materials from which? the zinc was readily distillable to hard sinter requiring higher-temperatures for zinc distillation. The rates of zinc distillation were increased by grinding the fuel finer; there were few benefits and loss of dust on grinding the sinter finer, unless the fine ?coal and fine sinter were brought into contact by pelletizing, and the pellets made but little dust.

Jan 1, 1948