Search Documents

By William Eathorne

"INTRODUCTION Retsof mine, adjoining the village of Retsof, Livingston County, New York, is about 5 miles northwest of Geneseo and 55 miles (air-line distance) due east of Buffalo. It is a single-bed rock-salt mine having extensive horizontal workings as much as 2-1/2 miles long and 1 mile wide and has been in continuous operation since 1885. Retsof tine is the largest producing salt mine in North America and is reputed to be the largest active salt mine in the world.Retsof is one of three large salt mines operated by the International Salt Co., Scranton, Pa.; T. Forster Courthope is general manager of Retsof and also of the company's Detroit salt mine in Michigan and has held that position for 27 years. He is assisted by Stanley Martin, general superintendent; R. Goetz, Maintenance superintendent; and John Riordan, mine superin¬tendent. All are old-timers at Retsof and, according to Courthope, contri¬buted the ""lion's share in bringing the mine to its present standard of safety.ACKNOWLEDGEMENTThis circular was made possible by the generous cooperation of T. Forster Courthope and his assistants, Stanley Martin, R. Goetz, and John Riordan. The information and time generously given are gratefully acknowledged.GENERAL INFORMATIONThe rock salt as mined contains about 99 percent sodium chloride and requires only crushing and screening to prepare it for the market. With the exception of a large jaw crusher underground, all crushing is done in a mill building attached to the headframe of the main hoisting shaft (fig. 1).Five sizes of salt are produced, ranging from about 1/2 inch diameter down to minus seven mesh."

Sep 1, 1949

By Ronald S. Conti

This U.S. Bureau of Mines report discusses the results of research conducted in the Bureau's experimental mine at Lake Lynn Laboratory on the response of fire sensors to simulated mine fires, which included (1) a slowly developing coal-conveyor belt fire, (2) a rapidly burning liquid fuel-belt fire, and (3) a liquid fuel-belt fire in the presence of diesel exhaust. During these tests, several mine fire sensors were evaluated with respect to sensor placement, spacing, and type. The data indicate that smoke sensors alarm several minutes before CO sensors do; and that, in the presence of diesel exhaust, a prototype diesel-discriminating smoke sensor can successfully function without being sensitive to the diesel contaminants. The vertical placement of sensors in the entry near the fire was also shown to be critical in terms of alarm times. Additional data showed that variations exist in response time and level of response for two brands of electrochemical CO sensor. Results also indicate that early detection of fires will improve the probability of miners' escape, because of reduced smoke concentrations during the incipient stages of the fire.

Jan 1, 2010

By Robert K. Koch, Henry E. Blake

Laboratory tests were made to determine if aluminum fluoride of commercial grade could be synthesized by reacting alumina hydrate with dilute ( 25 to 75 grams per liter of fluorine ) aqueous fluoride solutions . • Products containing up to 90 percent aluminum fluoride ( A1F ) were synthesized by reaction of alumina trihydrate ( A120 3H2O) with either dilute hydrofluoric acid ( HF ) or ammonium fluoride ( NHF) solutions , the ammonium fluoride solution resulting from ammonia ( NH ) desilication of a hydrofluoricfluosilicic acid ( HF - H₂ SiF ) solution . Fluorine recoveries of over 80 percent were obtained with either type of solution . The hydrated precipitates of AlF, and ( NH4 ) , A1F ( ammonium aluminum fluoride ) obtained by reacting hydrated alumina with these solutions were subsequently converted to anhydrous AlF, by controlled heating .

Jan 1, 1964

By Robert M. Becker

Part 5, the last of this series, deals with the theoretical confirmation and application of results developed in parts 1 and 2. The bulk-sampling variances of Hassialis and Kassel and Guy are compared with those in part 2, both as to formulation and as applied to ores and coal. The results provide confirmation for much of the development in part 2. Examples are presented for determining the reliability of bulk samples with respect to various measurable characteristics. These characteristics include, for example, assays for elements or compounds and particle surface area. The bulk samples considered consist either of a given weight, a given volume, or a given number of particles. In addition to problems of sample reliability, some of these examples may also be applicable to quality control. Several possible applications of results developed in parts 1 and 2 are outlined. These include tests for random data, degree-of-mixing indices, and particle-fineness indices.

Jan 1, 1966

By S. W. Zoldok

[The Bull Valley iron-ore district lie,; in the northern part of Washington County, Utah, approximately 30 airline miles southwest of the highly productive Iron Springs area (fig. 1). Iron-ore occurrences in the district have been known for many years, but they have not been mined, largely because of the inaccessibility of the area. The Bureau of Mines established a development project in the Bull Valley district in September 1941. Two separate areas, the Pilot and the Cove Mountain, were investigated. The work was planned to increase iron-ore reserves for steel production in the Western United States. During the project period three diamond-drill holes aggregating 1, 000 feet were completed (fig. 2). The program also included 6 408 linear feet of surface trenching and 171 feet of underground work (figs. 2 to 8, inclusive). Analyses were made of 460 samples from the diamond-drill holes and surface and underground excavations. The results of the analyses are given in tables 1, 2, 4, and 5, and the logs of the diamond-drill holes are shown in table 3. Field. work was completed in September 1942.]

Jan 1, 1953

By J. J. Forbes

Since 1910 the Bureau of Mines has given training in the care and use of oxygen breathing apparatus under conditions that may exist during mine fires and after mine explosions. In 1929 the Bureau supplemented this instruction by initiating a course in advanced mine rescue training to prepare mine officials and others to organize men for mine rescue and recovery operations. The course of instruction has been developed and expanded since its inception to keep abreast with new ideas, methods, and equipment. Four miners' circulars were issued to be used in the training course. The first of this series (Miners' Circular 33) deals with mine gases and the various methods of detecting them; the second (Miners' Circular 34) gives instructions for sampling and analyzing mine atmospheres; the third (this circular) describes methods and equipment for protection against mine gases; and the fourth (Miners' Circular 36) explains procedures in sealing and unsealing mine fires and in conducting recovery operations, These circulars have been revised from time to time to keep them up to date.

Jan 1, 1954

By Charles B. Kenahan

The chemical and galvanic corrosion properties of commercially pure titanium, a titanium-manganese alloy, a titanium-aluminum-tin alloy, 2 titanium-copper alloys, and 2 titanium-aluminum alloys were studied. Tests were conducted in synthetic ocean water, tapwater, 1-percent sodium hydroxide, 5-percent ferric chloride, and 5-percent ammonium sulfate solutions, various concentrations of sulfuric and hydro-chloric acids, and 1-percent oxalic acid. All tests were carried out at 35° or 60° C., with a flow of air or helium. Dissimilar metals involved in galvanic-couples experiments were aluminum, magnesium, and stainless steel. Electrode-potential measurements on single (uncoupled) specimens were also measured. Commercially pure titanium and the titanium-base alloys were generally quite similar in their resistance to corrosion, whether alone or in. contact with a dissimilar metal. Contact with the titanium metals caused aluminum and magnesium to corrode by galvanic action. Coupling with stainless steel in sulfuric acid solutions decreased the normal corrosion rate of the titanium metals. Contact with aluminum in air-aerated oxalic acid and 0.1N sulfuric acid solutions resulted in cathodic corrosion of titanium and the titanium-base alloys; however, there were a few exceptions. The copper alloys showed better corrosion characteristics than titanium in certain sulfuric acid solutions but were more susceptible to chemical attack in some hydrochloric acid solutions.

Jan 1, 1958

By T. T. Campbell

Although secondary recovery of lead and lead-tin alloys has been common practice in the United States during recent years, there is little published in-formation concerning recovery techniques. Available information does not cover metal recovery from wet dross skimmings. This investigation by the Bureau of Mines was undertaken to develop techniques that would allow lead-tin alloys to be recovered from wet dross skimmings containing large amounts of zinc chloride. A process was developed, on a laboratory scale, for recovering lead-tin alloys from wet solder dross skimmings. Straight water leaching, either with or without a second leaching operation carried out with a Na2C03 addition for removing chloride, produced a dross that could be smelted without further treatment. Overall recoveries averaging 92 percent of the metal values in the dross were obtained in the form of lead-tin alloys, which had an average tin content of 16 percent and lead content of 84 percent. The recovered alloy contained less than 0.02 percent zinc, as determined by both chemical and spectrographic analyses.

Jan 1, 1956

By M. A. Elliott, H. H. Schrenk, L. B. Berger, John C. Holtz

"INTRODUCTION Diesel-powered locomotives designed specifically for underground operation were used in the construction of some of the tunnels that comprise the Delaware Aqueduct in New York State. Before this there had been limited use of Diesel-powered equipment such as trucks, bulldozers, and shovels in tunnel construction in various parts of the country, but this equipment was used without modification for underground use and, in some instances, appar¬ently without due consideration of the hazards that might be created by the introduction of fuel-burning equipment into confined underground spaces.As certain definite advantages were apparent if Diesel haulage could be used in tunnel construction in some sections of the Aqueduct, the contractors who were to construct the tunnels in these sections were desirous of using, this type of haulage equipment if it could be used with safety. This matter was given careful consideration by the various agencies concerned with the establishment of safe practices on the Aqueduct project before tunnel driving was started. Of chief concern were the quantities of toxic or objectionable materials that would be discharged into the tunnel air by the exhaust of the locomotives and the volume of ventilating air that would be required to dilute these exhaust gas products to concentrations permissible in the atmosphere of working places."

Jan 1, 1947

By Mackenzie Burnett

Quick-Fix Blowout Stoppings were evaluated in several underground mines as an alternative to conventional ventilation control bulkheads. Blowout stoppings offer considerable savings in bulkhead construction and repair costs if the 0.1 inch H20 of differential pressure required to inflate them is available. The Quick-Fix Blowout Stoppings were utilized successfully in uranium mines in the Southwestern United States where savings in bulkhead construction and repairs to blast damaged bulkheads are estimated to equal $9,500 over the projected 2 year average life of a blowout stopping. Two types of material were evaluated. Five methods of anchoring the stoppings to drift walls were evaluated. Three methods of anchor attachment to the stopping material were evaluated. Blast pressure measurements were made in conjunction with the evaluation of the blowout stoppings.

Jan 1, 1978

By S. A. Matthes

This Bureau of Mines report describes analysis of a copper slag for 13 elements from a single sample solution by flame atomic absorption spectroscopy. Samples are dissolved with 7 ml of an HC1-HF-HN03 (3:1.5:2) mixture in heated plastic pressure vessels. A 1.5-pct boric acid solution is added to dissolve precipitated fluorides and to reduce matrix effects that interfere with atomic absorption analysis. Preparation time is less than 1 hour per batch of 10 samples. Total analysis time is less than 6 person-hours for 130 determinations with an average relative standard deviation of 1.83 pct for the 13 elements. Simple acid standards were used for all determinations. Values obtained by this method are in excellent agreement with values obtained by slower, more costly procedures.

Jan 1, 1980

By Lindsay D. Norman

Four chloride and seven fixed-nitrogen processes for recovering manganese from domestic resources are described. The chloride processes are divided into two classes (leaching and chloridization) depending upon the major operation responsible for converting the manganese minerals to the chloride from which manganese oxide products are obtained. The fixed nitrogen processes, all of which yield high-grade manganese oxide products, are essentially either leaching or roasting processes. The 11 processes include HC1 leach, HC1 chloridization, HC1 chloride volatilization, CaC12 chloride volatilization, NO2 leach, HNO3 leach, HNO3 ?NO2 leach, H3 ?CO2-H2O system leach, (NH4)2SO4 leach, (NH4)2SO4 roast , and ammonium salt roast .

Jan 1, 1963

By R. Duncan Gardner

This paper describing the milling practice at the concentrator of the Harmony Mines Co. is one of a series being; prepared by the Bureau of Mines on milling methods and costs in the United States. For the period February 15, 1929, to June 1, 1929, the concentrator treated 200 tons of copper ore per day containing 3.84 per cent copper and recovered 99.2 per cent of the total copper in concentrates averaging 26.61 per cent copper. Milling practice at the Harmony Mines is in most respects similar to the usual practice at the average flotation concentrator producing bulk flotation concentrates. The exceptionally high recovery is due to a number of minor conditions. These minor details will be stressed throughout this paper.

Jan 1, 1930

By Sarkis G. Ampian

Crystalline silica (quartz, cristobalite, and tridyrnite) is regulated by the Mine Safety and Health Administration (MSHA) and Occupational Safety and Health Administration (OSHA) because of its potential for causing debilitating but nonmalignant lung diseases. In 1987, the International Agency for Research Against Cancer (IARC) conducted a review of the health literature and concluded that crystalline silica was a probable human carcinogen. As a result of this finding, OSHA was required to regulate crystalline silica under its Hazard Communication Standard (HCS). The standard requires that all materials handled by OSHA-regulated facilities be labeled according to the requirements of RCS and that workers receive proper training on the handling of the material if the crystalline silica content equals or exceeds 0.1 weight percent (0.1 %). MSHA currently is considering enacting its own RCS. This will be similar to OSHA's RCS. If the standard is enacted, most mineral producers will have to determine the respirable monitor filter and bulk crystalline silica contents of their ores and products so that workers and/or customers will know whether they are in compliance with the 0.1% HCS and/or the OSHA permissible exposure level (PEL) of 50 µg for an 8-hour workday for respirable crystalline silica as determined from monitor samples. Two major concerns with the RCS are the widespread occurrence of crystalline silica in nature and the suitability of current technology for routinely determining crystalline silica concentrations at the 0.1 % RCS level. Most ores are extracted from silica-bearing deposits and it is a common constituent of rocks and soils. OSHA's RCS will have the greatest impact on the producers of crushed stone, diatomite, dimension stone, gravel, industrial sand, perlite, pumice, pyrophyllite, sand, and talc because these materials frequently are shipped directly from the mill to the customer. MSHA's RCS would affect nearly all mineral producers. Those producers that have crystalline silica present in concentrations near the 0.1 % cutoff point will have the most difficulty with the analysis. Crystalline silica can be quantified at the 0.1 % level by X-ray diffractometry in simple systems containing one, two, and possibly three minerals if (1) none of the accessory minerals has X-ray diffraction reflections that coincide or overlap with those of crystalline silica and (2) the standard has a particle size distribution and crystallinity similar to those of the sample. In some instances, it may not be possible to determine the crystalline silica content of a sample with any degree of certainty using the recommended regulatory protocol. In all cases, it is recommended that a qualified mineralogist identify the minerals in a sample prior to any regulatory analysis. Additionally, the uncertainty as to whether some silica polymorphs should be classified as crystalline or noncrystalline and the suitability of metastable high-temperature standards, such as cristobalite and tridyrnite, for regulatory analysis at ambient temperatures should be addressed further. This overview is written both to highlight these problems and to serve as a guide for analysts, regulators, and industry personnel who are involved in the crystalline silica issue. It also covers some of the difficulties and/or shortcomings in quantifying crystalline silica, such as the ubiquitous mineral quartz, in the workplace.

Jan 1, 1992

By R. L. Rough, W. K. Overbey

The Bureau of Mines obtained samples of oil - reservoir rock from wells in Ohio , Pennsylvania , and West Virginia as part of an investigation of the susceptibility of petroleum reservoirs to secondary - recovery techniques . Illustrations and tables showing the geographic and stratigraphic sequence of the cored reservoirs and 40 tables of detailed lithologic descriptions of the reservoirs are presented . Information relevant to geologic surroundings , oilfield history , coring and well logging operations , and reservoir core analyses are referenced throughout the report .

Jun 1, 1970

By H. C. Fuller, E. L. Anderson, F. S. Wartman, M. A. Cook

"This paper gives an account of the production of ductile-grade titanium powder in 100-pound batches by reduction of purified titanic chloride with magnesium, followed by grinding, leaching, and magnetic separation of the reaction product. Apparatus, technique, and methods of controlling product quality are described, and some data on operating costs are given.Although man has been aware of the existence of the element titanium for over 150 years, only recently has the metal itself been available in a form pure enough, particularly with reference to absorbed gases, to allow an estimate of its physical properties. In comparison with mild steel, the tensile strength of titanium is about the same, the resistance to atmospheric corrosion greater, and the specific gravity much less.These properties suggest the usefulness of titanium as a structural material for applications requiring resistance to atmospheric attack and a good strength-weight ratio. Although known reserves of titanium, high-grade enough to be useful at present are not sufficiently extensive to predicate that titanium might supplant iron, aluminum, and magnesium for structural purposes, the reserves are large enough to make its use as a structural material quite feasible in certain fields in which its unique properties are required.As a result of these considerations, the Bureau of Mines station at Tucson initiated an, investigation into the technology of titanium in 1938. First, a critical survey and small-scale trial of virtually all suggested methods7/ for producing the metal was made. The method devised by Kroll8/ seemed best adapted as a source of metallic titanium for, although the purity of the product was not as high as that of products from some other processes, it seemed that modifications in technique necessary for larger-scale production could be made more easily.Essentially, in applying the Kroll process, titanium tetrachloride was reduced to metallic titanium by adding the chloride slowly to molten magnesium contained in a molybdenum-lined iron reaction chamber filled with a protective atmosphere of argon. After reduction to the state of completion desired, the reduction mass and chamber were allowed to cool. Then the chamber was opened, and the reaction mass, consisting of titanium, magnesium chloride, and some unused magnesium, was removed by suitable means. Most of the magnesium chloride and metallic magnesium were removed by leaching in dilute hydrochloric acid. The leached sponge was then ground wet in a ball mill, releached in strong acid, and dried Removal of free iron by magnetic separation completed the production process.Development of the Kroll process by the Bureau was undertaken first at the station at Salt Lake City, in 1942 and the amount formed per run was increased in several steps from a few grams to pounds.9/ In addition to increasing the size of batch over that used by Kroll, the technique was simplified somewhat by the use of unlined reaction vessels."

Aug 1, 1949

By W. M. Mahan

This report describes work carried out by the Federal Bureau of Mines in cooperation with the General Services Administration (GSA). Tests on nickel oxide reduction were conducted at the Pyrometallurgical Laboratory at Pitts-burgh and Bruceton, Pa., and at a rented plant at Canonsburg, Pa. Nickel oxide was reduced to sponge nickel, which was then melted to produce specification-grade nickel ingots containing a minimum of 98.50 percent nickel plus cobalt and a maximum of 1.00 percent cobalt. One purpose of this study was to determine if specification-grade nickel could be made from nickel oxide produced at the United States-Government-owned plant at Nicaro, Cuba, in pilot-plant scale operations involving direct reduction and melting processes. A second and equally important purpose was to obtain cost data on the pilot-plant operation to estimate the cost of producing ingot nickel at an annual rate of 12 million pounds. Laboratory tests verified that nickel oxide, in saggers and in the presence of anthracite fines and dolomite in the ratio of approximately 20:5:1, could be converted to sponge nickel when heated to approximately 1,900° F. for about 2 to 4 hours, depending on the size and density of the oxide charge. The tests also determined the type of saggers suitable for pilot-plant operations.

Jan 1, 1959

By D. D. Fischer

Recovery and separation of molybdenum and rhenium from a process solution was accomplished by a technique developed by the Federal Bureau of Mines involving a combined solvent extraction and activated carbon adsorption procedure. The processing sequence required treatment of the solution with S02 to reduce the chlorate ion and adjust the pR prior to solvent extraction of molybdenum and rhenium with a tertiary amine. Molybdenum and rhenium were stripped from the organic phase with an NH40H solution, and the strip solution was then passed through activated carbon to preferentially adsorb the rhenium. After washing entrained molybdenum from the column with a brine solution, rhenium was eluted with an MeOH-H20 mixture. The activated carbon was regenerated with water. Molybdenum was recovered as (NH4)6Mo7024 by evaporating the column effluent. Rhenium in the column eluate was reextracted with a tertiary amine, stripped from the organic phase with dilute NH40H, and recovered as NH4Re04 by evaporating the strip solution. The final (NR4)Re04 product contained < 80 ppm impurities. Sodium sulfate was crystallized from the first solvent-extraction raffinate by lowering the solution temperature to 0° C. Precious metals contained in the original process solution were adsorbed onto the activated carbon.

Jan 1, 1975

By Charles N. Speltz

Coal resource data from public and private sources, in conjunction with previously published data, were used by the Bureau of Mines to determine the location and extent of strippable coal resources in Colorado. Total strippable resources of approximately 18 billion tons were estimated in 12 separate coal regions, fields, or deposits. Coal recoverable by contour mining techniques was not included. Criteria used in defining strippable resources were a minimum coalbed thickness of 2 feet and a maximum overburden thickness of 150 feet, except where the coalbeds are of exceptional thickness. Ail Colorado coal is either Cretaceous or Tertiary in age. Cretaceous coals occui In the Dakota Sandstone, the Mesaverde Group, and equivalent formations while Tertiary coals occur in the Dawson Arkose, the Fort Union and the Wasatch Formations, and equivalent formations. The strippable coal ranges in rank from bituminous in the Yampa region to ligniferous in the Denver basin. Ali this coal is low in sulfur content (less than 1 percent); ash content is low to high; heating value ranges from 3,000 to 12,000 Btu&apos;s per pound. Ash from the lignite of the Denver basin was found to contain an abnormally high percentage of kaolinite which conceivably could be recoverable as alumina.

Jan 1, 1976

By James C. Duchon

The use of extended workdays (regular shift lengths of 10 or 12 h (hour), while still maintaining a 4O-h workweek) in mining operations is attracting growing interest in the United States. There is very little doubt that extended workdays is a very popular alternative among the work force because of the significant increase in days off, including weekends, especially when compared with traditional rotation schedules of working seven straight shifts or having only one weekend off every 4 to 6 weeks. However, there are some serious concerns by management, workers, unions, and various governmental policymakers that working 10-or 12-h days may create an added risk of accidents and health problems. The U.S. Bureau of Mines reviewed the literature studies related to the safety and performance issues of extended workdays. This report presents a summary of those findings. The studies examined in this review are divided into three sections: (1) laboratory, (2) field, and (3) accident and injury analysis. In general, results are inconclusive. Studies have shown both positive and negative effects. It is concluded, therefore, that in industries such as mining where accidents are a serious concern, special measures and evaluation in the use of extended workdays be considered.

Jan 1, 1994