Search Documents

By Jon C. Volkwein

The Bureau of Mines conducted a series of tests to evaluate the effectiveness of mixing a compressed-air-generated foam with dried whole-grain silica sand to suppress dust in minerals processing plants. Dust at downstream transfer points was monitored with personal gravimetric samplers and with Real-Time Aerosol Monitors (RAM's) that were connected to strip' chart recorders. Results showed dust reductions of 80 to 90 pct on three separate occasions at two different plants. The mechanism by which foam suppresses dust is discussed, as are the constraints on the use of foam, which may include incompatibility of the foam with the mineral product, difficulty in controlling the foam generator, and cost.

Jan 1, 1983

By D. Bienstock, R. C. Kurtzrock, E. R. Bauer, J. H. Field

To remove hydrocarbons and carbon monoxide in automotive exhaust by oxidation , a catalyst of 4.2 percent Uз Og , 1.7 percent Cr₂ 0 , and 1.7 percent CuO supported on 1 /8 - inch y- alumina spheres was tested in a reactor in place of the muffler of a 1 / 2 - ton truck . Tests were made with both nonleaded and leaded gasolines . With the engine at operating temperature , tests were made with the engine idling and with the vehicle cruising at 30 mph . Auxiliary air was added to maintain an oxygen concentration of 3 to 4 percent in the gas leaving the catalytic reactor . The vehicle was operated for 83 hours (about 60 percent of the time with the engine idling ) and 525 miles with nonleaded gasoline . Conversions of 98 percent of the hydrocarbons and 100 percent of the carbon monoxide were achieved with the engine idling and with 7,000 ppm carbon atoms and 4- percent carbon monoxide in the feed to the reactor . Hydrocarbon conversions of 75 percent were obtained at cruising speeds of 30 mph with a feed of 1,700 ppm carbon atoms ; the carbon monoxide concentration was less than 0.3 percent in the feed and was unchanged in passage through the reactor . Identical activity was obtained initially in switching to a gasoline containing 1.9 ml tetraethyl lead (TEL) per gallon . However, there was a gradual loss in activity thereafter . Conversions in tests with the engine idling about 50 percent of the time , had decreased by 23 percent for the hydrocarbons and by 25 percent for the carbon monoxide from their initial values after 122 hours and 1,300 miles of operation with leaded gasoline . The levels of radioactive materials in the exhaust of the reactor and the radiation in the vehicle were negligible .

Jan 1, 1963

By T. F. Anstett

The Bureau of Mines evaluated the potential availability of chrysotile, amosite, and crocidolite asbestos from 42 properties in market economy countries. This resulted in the development of tonnage-cost relationships indicating the quantity of grades 3 through 7 asbestos at various average total costs of production at 0% and 15% rates of return on invested capital. The availability of grades 2 and 8 was also evaluated, but since each is produced at only one property, no analytical results were given. Total demonstrated recoverable chrysotile fiber potentially available of grades 3 through 7 from the 42 properties evaluated follow: 1.59 million t, 21.00 million t, 16.74 million t, 15.54 million t, and 19.27 million t, respectively. The total amount of crocidolite is 1.69 million t. Owing to the good potential for discovery and development of new deposits, long- term availability of fiber of all three types is not in jeopardy. However, many of the crocidolite properties evaluated in the northern Cape crocidolite field of South Africa have relatively small demonstrated resources, and new deposits will have to be exploited by the late 1990's to sustain projected levels of production.

Jan 1, 1985

By A. E. J. Gallagher

This report summarizes the results of flotation studies conducted by the Federal Bureau of Mines on samples of extremely fine-grained lead-zinc sulfide ores. Samples from five ore deposits in the Pine Creek area, Coeur d'Alene district, Idaho, and one deposit in the Metaline district, Washington, were studied at the Albany Metallurgy Research Center to determine the recovery of sulfide lead and zinc by flotation. During the investigation it was found that flotation could be effectively applied to the selective recovery of exceedingly fine-grained lead and zinc sulfide minerals. Separation of galena and sphalerite was obtained on pulps ground through 1,600-mesh, in which most of the particles were smaller than 5 microns. Selectivity and recovery of minerals in this fine size range were enhanced by use of a chemical dye, diphenylthiocarbazone, as a galena promoter. Although unsuccessful on one ore, application of the dye in treatment of two other very fine-grained ores yielded lead concentrates containing over 62 percent Pb at recoveries in excess of 85 percent. More than 55 percent of the lead in these concentrates occurred as particles smaller than 2 microns.

Jan 1, 1961

By Edward W. Parsons

To determine in what part and to what extent creep or movement exists in an installed rock-bolt anchor and the effect of the creep or bleedoff on the tension load on a rock bolt, as well as the effect of normal mining activity on the rock-bolt load and anchor, the Bureau of Mines conducted tests in the laboratory and in two mines using four types of expansion-shell anchors, the wedge bolt, and in one mine, explosive-anchored rock bolts. Specially mounted heavy-duty springs, calibrated to obtain load readings from spring movement, were installed on the test bolts to prevent a drastic reduction in tension load caused by slipping or seating of the anchor. A dial gage, reading to 0.0001 inch, measured movement of the anchor shell against the rock and seating of the anchor wedge plug in the shell. While all bolts had electrical resistance strain gages for load reading, only readings from the laboratory tests were used because those from the field tests were erratic. The tests revealed that most load loss resulting from static loading is due to the slippage and seating of the serrations on the anchor shell into the drill-hole wall. Dynamic loading, primarily from sudden shocks from nearby blasting, and possibly from ground movement or mining activity, will cause the anchor wedge plug to seat in the anchor shell.

Jan 1, 1969

By Arnold C. Love

This report discusses current research by the U.S. Bureau of Mines on the effects of whole-body vibration (WBV) and shock on underground mobile equipment operators. The highlights of a comprehensive literature review of WBV, shock, and seating are presented. Factors discussed include health and physiological effects, comfort, performance, and fatigue. Vibration data were collected from shuttle cars and ramcars at several underground coal mines in Pennsylvania, Ohio, and Illinois. The data were formatted so that they could be used to drive the Bureau's motion platform, and to compare them with ANSI S3-1979, Guide for the Evaluation of Human Exposure to Whole-Body Vibration. Human subject testing in the Bureau's vibration research laboratory evaluated the effects of two different seat angles and of the presence or absence of vibration and of foam padding on heart rate, blood pressure, and subjective discomfort. Only vibration significantly increased heart rate and systolic and mean blood pressures. Vibration and a steel seat had a significant effect on subjective discomfort. The apparatus used for these tests and the experimental procedures are described in detail. Recommendations are made for additional research on the exposure of underground mining machine operators to WBV and shock.

Jan 1, 2010

By S. L. May

Procedures for separating columbium and tantalum have been developed by the Bureau of Mines as part of a broad research program on the utilization of low-grade ores of columbium and tantalum, Columbium and tantalum compounds of greater than 99 percent purity have been obtained by application of the solvent extraction separation system: Hydrofluoric acid-sulfuric acid-methyl iso-butyl ketone. This system is unique in that it not only separates columbium from tantalum, but also separates these two metals from other metallic impurities. The system is effective for separating the metals irrespective of the tantalum and columbium ratio of the starting materials. Investigations in which the spent feed obtained from the initial coextraction step was recycled to the system indicated that efficiency was increased, and cost was reduced without impairing product purity. Continuous tests demonstrated that this solvent extraction system could be used in large-scale equipment without loss in efficiency or in purity of products. The separation of columbium and tantalum has been difficult because of the similarity in their chemical bahavior. Many methods have been proposed for separating these two elements, but most methods either did not achieve satisfactory separation or were tedious and time consuming. The Marignac process (3, 4)4 developed in 1866 was the only method used commercially until recently. This separation procedure is based on the difference in solubility in aqueous solution of potassium tantalum fluoride and potassium columbium oxyfluoride. Current commercial practice appears to favor solvent extraction as a method for separating tantalum from columbium (1). Several efficient methods for separating columbium from tantalum by solvent extraction (2, 9, 8) were reported earlier from this laboratory.

Jan 1, 1961

By A. L. Peyton

The Brewer mine, near Jefferson, Chesterfield County, S. C., was originally operated as a gold mine. As late as 1890 this mine was reported to have been one of the large gold producers in the southeast. Occurrence of topaz on the Brewer property was not reported until 1935, when it was discovered, by Parks3/ and Parks of the Federal Geological Survey while they were investigating gold deposits in the Piedmont province.

Jan 1, 1953

By W. P. Yant

[At the majority of mines where flame safety lamps are used either as working lights or as a means of detecting gas, no check it made on this condition of the various parts of the lamp and their assembly other than a visual ink inspection. Although this inspection should be made carefully in view of tae serious consequence that may follow Vie use of a faulty lama, In many instances the inspection is of a perfunctory nature. The Bureau of Mines has therefore designed a small box or gallery for testing lamps for defects and improper assembly before they are taken into the mine. The test simulates the condition when a lamp is extinguished by its introduction into an explosive mixture and the operator attempts to relight the wick while the lamp contains the explosive mixture. This test is more rigorous than merely subjecting a lighted lamp to an explosive methane-air mixture. In the latter test the products of combustion tend to blanket the propagation of flame from within the lamp to the exterior, especially if there are defects at the top of the gauzes. Moreover, when the lighted lamp is subjected to an explosive methane-air mixture the methane builds up slowly within the lamp until the lower inflammable limit is attained, whereupon a feeble explosion occurs within. If the nonlighted lamps is first filled with the methane-air mixture that gives the maximum violence and is than ignited, the dampening effect of products of combustion is obviated and the strain on defects is]

Jan 1, 1930

By Robert L. Jones

The Boston Consolidated mine is situated in the Bingham mining district, Salt Lake County; Utah (fig. 1). The property has had a noteworthy production of cupriferous, gold-bearing, pyritic ore in addition to lead ore. The Bureau of Mines established a diamond-drilling development project on the property in September 1943 with the primary objective of determining the continuity of a mineralized zone in the Commercial limestone below and to the northeast of the 800-foot level (fig.2). Examination of the geologic feature at the property previous to drilling indicated that the mineralized limestone horizon would continue belay the 800-foot level, but with a flatter dip than disclosed above this level. During the project period, 36 holes totaling 4,001 feet were drilled from underground stations outlining the zone below the 800-foot level (figs. 2 and 3).

Jan 1, 1949

By R. M. Jimeson

Pressure-drop measurements through beds of granular iron, lathe turnings, steel wool, and parallel-plate assemblies were made at linear velocity and gas-density ranges expected in the Fischer-Tropsch hot gas recycle process.4/ Equations relating pressure drop, linear velocity, gas density, and bed porosity were derived. The results indicate that the exothermic heat of reaction can be removed at a lower cost by using catalyst beds with high porosity. INTRODUCTION The Fischer-Tropsch hot-gas-recycle process requires a catalyst offering low resistance to gas flow as one condition to economic feasibility. Conventional granular or spherical catalysts used during early development of the process in Germany did not meet this requirement. Large pressure drops across these beds made the cost of recirculating the gas excessive. The Federal Bureau of Mines is investigating the process by using novel and unusual catalysts that offer little resistance to gas flow. Pressure-drop measurements across these types of catalyst beds are discussed in this report.

Jan 1, 1959

By Ann G. Kim

The U.S. Bureau of Mines applied its mine fire diagnostic method to an abandoned anthracite mine fire site in Carbondale, Lackawanna County, P A. The technique to locate fires in abandoned coal mines and coal refuse piles includes the determination of hydrocarbon concentrations in mine gases, the imposition of an underground gas flow direction, and use of a surface mapping method, to define heated and cold zones in underground coal strata. The heated zones at Carbondale were characterized by elevated methane concentrations. The results of 25 communication tests were analyzed to define 2 large (approximately 100 by 250 ft) and 5 small, isolated heated zones. An approximate correlation existed between the location of the heated zones and areas of anomalous snow melt. The correlation between the results of the diagnostic? test and subsurface temperatures was not significant.

Jan 1, 2010

By H. M. Cooper

Many analysts have had difficulty in obtaining accurate and consistent determinations of the volatile matter in low-temperature coke when the usual standard method for coal was followed. The tendency is toward too-high results, due to mechanical losses which are extremely difficult to avoid or control. With cokes there also may be an error due to excessive oxidation of the fixed carbon. Much of the earlier experimental work on the volatile-matter determination in coal, such as that of Parr, Fieldner and Davis, and others, has been on the effect of time, temperatures, shape and size of crucibles, method of applying heat, and type of furnace, all of which data has evolved the present A.S. T. M. standard method for volatile matter in coal and coke. It is not the purpose of this investigation to deal directly with the above phases of the procedure, but rather to study some of the factors affecting the results in those types of fuel which give erroneous results due to mechanical losses. This mechanical loss is usually designated as "sparking." There are two kinds of sparks or incandescent particles which may appear: particles of soot from partially condensed carbon from the burning gases, and unburned particles of the material itself which escape. The first type does not affect the accuracy of the volatile matter results, and is therefore negligible. The second type, however, causes appreciable loss and results in showing higher volatile percentages than actually exist.

Jan 1, 1932

By K. Shimamoto

This study has been prompted by the anticipated demand for rhenium by the petroleum industry and the concern for an adequate supply of rhenium to meet the demand. The present and projected outlook for rhenium relative to its distribution and occurrences, the recovery factors involved in ore beneficiation, capital and operating costs, changing technology, and the projected uses and market growth of rhenium are presented in this report as part of the Bureau of Mines program to determine the availability of recoverable rhenium in a developing market.

Jan 1, 1973

By H. W. Sheffer

Technical and economic aspects of community refuse disposal systems and their effects on the environment are identified and described. Seven landfills and two incineration systems, located throughout the United States, are reviewed.

Jan 1, 1971

By J. A. Cavallaro

The heats of formation of anhydrous barium carbonate (witherite), strontium carbonate (strontianite), and lead carbonate (cerussite) were determined by solution calorimetry. The solution mediums were hydrochloric acid for barium and strontium carbonates and perchloric acid for lead carbonate. The heats of formation at 298.15° K are as follows: BaCO3 -297.5 ± 0.8 kcal/mole; SrCO3 -294.6 ± 0.5 kcal/mole; and PbCO3 -168.0 ± 0.3 kcal/mole.

Jan 1, 1966

By G. H. Keith

The Bureau of Mines determined the mechanism(s) involved in observed anomalous changes in mechanical properties of vanadium-base alloys. Tensile properties of electrorefined and commercial-purity vanadium-base alloys containing up to 5 atomic percent molybdenum or titanium were measured between 77° and 673° K. Snoek oxygen and nitrogen peak heights were measured to determine the changes in dissolved interstitial content caused by increasing quantities of solute. In addition, changes in lattice parameter were followed wit: precision X-ray techniques. Softening, observed in alloys containing titanium, is explained by the formation of a second-phase titanium compound with oxygen or nitrogen. However, because of partitioning of titanium between compound formation and solid solution formation, about five times the stoichiometric amount was required for complete reaction. Addition of 1 percent titanium drastically lowered the strengthening due to strain aging, at 673° K, and 2 percent titanium essentially eliminated it. All alloys were ductile at 77° K. Variations in the tensile properties of the molybdenum-containing alloys are explained by variations in the amounts of interstitial impurities present. The molybdenum did not react with these impurities and had no effect on strengthening due to strain aging. Commercial-purity vanadium alloys containing more than 2 percent molybdenum were brittle at 77° K.

Jan 1, 1969

By L. C. IlsLey

The last previous Bureau of Mines publication relative to details of permissible methane detectors (Bulletin 331, published in 1930) describes detectors of four different types, namely flame, combustion, catalytic, and a combination Weatstone-bridge and catalytic type in which catalytic action at the surface of a platinum filament when in methane causes a change in the temperature and resistance of the filament, thus unbalancing the bridge circuit and giving a reading proportional to the methane concentration. Three detractors of the latter type have been approved since 1930. A brief description of each follows: U. C. C. Detector Approval No. 902, covering the U. C. C. indicating detector, as described in Bulletin 331, was extended. January 27, 1930, to cover important changes in design that permit checking the calibration of the detector at any time whether in gas or fresh air. Essential features of the detector are shown in figure 1.

Jan 1, 1937

By Deno M. Pappas

The objective of this Bureau of Mines investigation was to identlfy and evaluate alternative binder materials for use in stabilizing and consolidating highly fractured roof along longwall faces and gate roads. The desirable characteristics of a stabilization material were defined, and an extensive search was conducted to find materials satisfying these characteristics. Of 20 materials originally scrutinized, 9 were chosen for laboratory analyses. The laboratory tests evaluated bond strength and tensile strength under both dry and wet conditions. An optimum material was not found. The laboratory analyses indicated two possible candidate materials for longwall stabilization: high-aluminous cement and two-component epoxy; however, the tensile strength of the high-aluminous cement was mediocre, and the epoxy cement is toxic, flammable, and fairly expensive. The potential market demand for an effective and economical stabilization macerial is discussed in the appendix.

Jan 1, 1988

By E. G. King

Many of the existing thermodynamic values for the titanium halides are estimates, including all the entropies and high-temperature heat contents of their crystalline and liquid phases. This report contains the results of low-temperature heat capacity measurents (which lead to entropy values at 298.15° K,) and high-temperature heat-content measurements of four halides - trichloride, tribromide, tetrabromide, and tetraiodide. The new data are combined with selected heat-of-formation values at 298.15° K. to obtain improved values of the heats and free energies of formation of these halides at high temperatures, thus supplementing the previous data of Kelley and Mah.5/ ACKNOWLEDGEMENTS This investigation was conducted under a cooperative arrangement between the Federal Bureau of Mines and the Department of the Navy, Office of Naval Research. The work was done by Bureau of Mines personnel using Bureau of Mines calorimetric equipment. The Office-of Naval Research supplied the supporting funds and arranged for procuring the samples of the titanium halides. The samples were prepared and analyzed by the Inorganic Chemistry Section, Division of Chemistry, National Bureau of Standards.

Jan 1, 1961