Search Documents

Most laboratory sealant studies were carried out in 2.0 inch I.D. Plexiglas tubes of 9.0 inches height containing 4.0 to 4.5 inches reconstructed soil from an 0-8 or 8-16 inch soil horizon at the Lanse site. (When soil was used from the Kato site, the top soil horizon was approximately 0-4 inches. The 4-8 inch horizon was somewhat comparable to the Lanse 8-16 inch horizon.) A 20 mesh Saran or steel screen was placed over the rubber stopper with a bottom drain to a 100 ml measuring cylinder. In some earlier experiments a 1/2 inch bed of 1/4 inch pea-gravel was then added, but in later experiments this was eliminated as it showed no particular utility. Field soil samples collected by a shovel were stored in sealed containers and sieved through a 4 mesh screen just before use. (Moisture content was typically about 25% for A horizon soil and about 20% for B horizon soil.) The sieved soil minus roots was then added in increments of about 1 1/4 inches. Compaction was effected by dropping a weighted ramrod (1-7/8 inches O.D,) five times from a height of two inches. If about twenty tamps were used or if the soil columns were rapped vigorously while water-logged, compaction was high with no detectable percolation. Freezing such samples would then usually cause very slow percolation, e.g. 1-2 ml/day. Using this as a standard procedure, percolation flows were usually stablized after two to three days to rates of about 100 to 200 ml/hour. Percolate was recycled carefully to minimize disturbance of the soil surface. When percolation flows were about 100 to 200 ml/hour, various additives (sealants) were introduced to the moist column in two to three increments to maintain a slight head. Additive concentrations were usually 2-1/2% with some at 5% in earlier experiments. Typical use of 40 ml of 2-1/2% additive corresponds to 4400 lbs/acre. When no more additive was present as supernatent liquid, water washes of about 15 ml were then used several times followed by special additives as needed. More water washes were then used to maintain a head of about 1/2 inch. Percolate was collected in 100 ml cylinders to measure percolation rates in ml/hr. Turbid percolate was evaporated to determine amount of eluted latex. Percolate was sometimes checked for pH by Pan-pH Indicator Paper9,10 reading in 0.5 units. Surface tension measurements were sometimes made by a DuNouy tensiometer10 in experiments using a surfactant for pretreatment.

Jan 1, 1972

By A. E. Back

A method has been developed in the laboratory for successfully treating titaniferous magnetite ore from the deposit at Iron Mountain, Wyo. The ore is roasted with 15 percent sodium carbonate to convert the vanadium to a water-soluble form and fix the soda for the subsequent electric-smelting step. Approximately 90 percent of the vanadium is recoverable in a product assaying 80 percent V2O5. The leached calcine is briquetted and smelted in a graphite-lined electric-arc furnace. Substantially all of the titanium is recovered in a soda slag, assaying 60 percent TiO2 and 2 percent Fe, which can be upgraded to 75 to 80 percent TiO2 by leaching with dilute sulfuric acid. The upgraded slag could be utilized for the production of titanium dioxide pigments or titanium tetrachloride. About 90 percent of the iron is recovered as pig iron, containing only minor amounts of vanadium, titanium, and sulfur. The high TiO2 slag compares favorably with slag containing about 70 percent TiO2 being produced by the Quebec Iron & Titanium Corp. at Sorel, Quebec. The data obtained from this investigation indicate that a feasible process has been developed for treating Iron Mountain ore, and larger-scale testing is warranted to develop engineering data for the ultimate utilization of this deposit as a source of titanium, iron, and vanadium. There are adequate supplies of basic raw materials, electric power, water, sodium carbonate, coal, and petroleum products within fairly short distances of Cheyenne and Laramie, Wyo., the nearest cities and probable plant- and labor-supply points.

Jan 1, 1952

By F. J. Palumbo

An electronic color-sorting machine was tested for recovering colorless glass concentrates from mixed glass products. The tests were made using glass recovered from unincinerated (raw) urban refuse and residues resulting from the incineration of refuse. The results of the study revealed that concentrates analyzing about 86 percent colorless glass could be recovered from mixed unincinerated glass containing 54 percent colorless glass material. Recovery of the colorless glass was about 62 percent. Color sorting the incinerated glass was somewhat more difficult. Multiple-stage processing was required to recover 59 percent of the colorless glass material in a product analyzing 89 percent colorless glass. The feed material analyzed 41 percent colorless glass.

Jan 1, 1971

By G. H. Keith

A vanadium-base alloy consisting of the following elements in weight-percent--molybdenum, 20; titanium, 10; carbon, 0.1; silicon, 0.5; and yttrium, 0.5--had exceptionally high strength at temperatures up to 1,200° C. This alloy was capable of fabrication to sheet of ~ 1 mm thickness by a combination of hot swaging and hot and warm rolling. In the warm-rolled condition at ambient temperature, its ultimate tensile strength was 1,205 MN/m2. The strength at 1,200° C was 150 MN/m2. Within the temperature range of 25° to 1,200° C, the ductility of the alloy as measured by elongation increased from 4 to >90 percent. Strengthening was achieved by both solid-solution and dispersed-phase mechanisms. Alloys of 20 percent molybdenum and 10 percent titanium were stronger than the other molybdenum-titanium alloy compositions tested. Strength was increased 15 percent in the temperature range of 25° to 800° C, with no accompanying loss in ductility, by the addition of 0.5 percent silicon. Workability was improved by additions of 0.25 and 0.5 percent yttrium.

Jan 1, 1970

By Philip Thompson

A part of the Bureau of Mines mission is to help improve the Nation's mineral posture by providing the technology for utilizing low-grade ores. In this regard, laboratory testing by the Bureau of Mines has shown that the removal of insoluble slimes using selective flocculation and flotation is a viable method for treating low-grade potash ores that have a high content of water-insoluble impurities. Results indicated that over 82 percent of the insoluble slimes could be removed from sylvinite ore containing 5 percent water insolubles and 13 percent K20 by using nonionic or cationic polyacrylamide flocculants and cationic, anionic, and/or nonionic collectors. Subsequent potash flotation recovered 87 percent of the potash in rougher concentrates containing 57 percent K2O. Sizing and cleaner flotation of the rougher concentrates upgraded the products to 60 percent K2O. Filtration of the water-leached insoluble-slimes flotation concentrates on a bed consisting of leached insoluble-slimes concentrate mixed with potash flotation tailings recovered 80 percent of the brine. Filtration rates using the mixed bed were nine times faster than filtration rates obtained when the insoluble-slimes flotation concentrates were filtered separately.

Jan 1, 1979

By M. S. Cetiner

This report describes the prototype development If a medium to high voltage coupler, suitable for underground coal mining operations. The coupler has such unique features as automatic dust covers and continuous phase pin shielding. The coupler is rated at 7500V and 250A continuous operation.

Jan 1, 1982

By Warren Hastings

This paper describes the methods and costs, in units of labor end materials, of sinking a 7 compartment vertical shaft 1,261 feet through a fractured, water-saturated formation. The shaft, designed for hoisting 2,500 tons a day, is at Friedensville, Lehigh County, Pa., approximately 6 miles south of Allentown and Bethlehem. It was sunk by the E. J. Longyear Co. under contract to the New Jersey Zinc Co. Preparation for shaft sinking W8A begun July 1, 1947, and sinking was completed August 18, 1952. A total of 604,858 man hours was required to sink the shaft.

Jan 1, 1954

By T. E. Sterner

The Bureau of Mines investigated the use of a chromatographic gas analyzer in determining the concentration of combustion products in gas produced during field and laboratory thermal oil-recovery tests. Several parameters (carrier-gas flow, cell current, sample size, and temperature) known to affect quantitative analyses were studied using a commercially available dual-column, dual-detector chromatographic gas analyzer which had been modified to provide close control of these variables. The apparatus made possible a much closer control of air-and gas-injection rates and provided adequate data for performing material-balance calculations and for determining oxygen utilization during the laboratory and field combustion tests. The chromatographic analysis also aided materially in evaluating and measuring bypassing and gas travel times and in detecting high-permeability zones that were present in the reservoir.

Jan 1, 1965

By A. E. Gooch

The Bureau of Mines conducted research in an attempt to provide a more sound basis for recommending improved artificial support during deepening of the main shaft of the Lucky Friday mine in the Coeur d'Alene mining district of northern Idaho. Field measurements of closure across the short axis of the 13-by 26-foot shaft were as high as 16 inches. Elastic/plastic finite-element (F/E) analyses were made, reducing the values of large-scale in situ rock mass properties until field closure measurements generally corresponded to displacements in the F/E analyses. Resulting plots of rock mass displacements, stresses, and areas of plastic failure display the results of creating openings (shaft, in this case) in deep mines in difficult ground conditions requiring artificial support.

Jan 1, 1976

By R. L. Bolmer

Driving long development raises probably is one of the most hazardous and expensive operations in underground mining. The safe handling of men and materials becomes more difficult and more time consuming in the higher sections of the raise. The efficient ventilation of these sections often is a major problem. This information circular describes a unique method by which Resurrection Mining Co, safely and efficiently completed a 622-foot vertical raise at its Irene shaft near Leadville, Colo. The method used by the company involved driving a raw, 6-foot-diameter ventilation raise and emergency escapeway, using a work cage that was suspended on a hoisting rope extended down a small-diameter drill hole. Although the method was new and experimental, the raise was completed in record time. Overall costs were less than they would have been with conventional methods. The company's initial experience suggested improvements both in design and operating technique that should prove of value to others who contemplate using the cage method of raising

Jan 1, 1958

By Cloyd M. Smith

Progressive mine management is placing increased emphasis on improved ventilation as a contribution to better safety , health , and productivity of miners . Management is on the alert for means of bettering the working environment by increasing the flow of air and distributing it more effectively to the working places , having in mind the necessity of avoiding exorbitant ventilation costs . A basic need in planning betterments of this kind is knowledge of existing rates of flow and air pressures , infCoorrmmaattiicon that is supplied through ventilation surveys . Some companies make partial surveys from time to time , but few make complete surveys on a routine basis . This report describes the practice of a large British anthracite -mining company , which operates 24 collieries in South Wales , in carrying out a routine program of ventilation surveying . Ventilation characteristics and climatic conditions in the working places of its collieries are determined at frequent intervals with a view to increasing the effectiveness of ventilation and protecting the health of workers . It is thought that many of the points of the procedure used in making the surveys and in compiling and reporting the results will be applicable to American practice and that a discussion of the program may be helpful to colliery managers who are planning similar work .

Oct 1, 1949

By William J. Wuest

The technical analysis of parameters that can influence roof and rib reinforcement is important to the operation of safe and profitable underground mines. One such parameter, studied in this U.S. Bureau of Mines investigation, is the effect of time on untensioned, resin-grouted bolt anchorage characteristics. A group of seventy-three 4-ft-long bolts with three different grout column lengths were I installed in a stable coal mine roof. The bolts were then subjected to standardized pull tests at various intervals throughout a 37-month period. For each test, load-deformation data were reduced to determine axial stiffness and yield point. The magnitudes of these two anchorage characteristics at the time of installation were compared with results from subsequent pull tests to determine if anchorage capacity deteriorated. Bolts with 18-in grout columns were studied over 9 months, and no measurable loss occurred. Bolts with 48-and 24-in grout columns were studied over 37 months and also exhibited no measurable loss.

Jan 1, 2010

By Robert S. Dalzell

Following the introduction of roof shields to the U.S. longwall mining scene in 1975, the number of shield faces (faces supported by shields) has increased steadily, and the occurrence of accidents associated with ground control inadequacies at longwall operations has shown a downward trend. However, ground control problems in longwall mining still exist. New mining systems, however efficient, have run afoul of roof control. Shield faces have suffered extended stoppages because of roof cavities. In this report, the Bureau of Mines addresses the problem of longwall roof control. The report presents a review of foreign remedial and strata replacement techniques for longwall faces and evaluates their potential for domestic application. The technology reviewed includes meshing, chemical rock stabilization, cribbing, strain-absorbent modules, inflatables, synthetic foam, and monolithic fills.

Jan 1, 1985

By L. F. Heising

The Bureau of Mines evaluated 191 composites from the central Mesabi Range, Minn., chiefly by reductive roasting and magnetic separation. After reductive roasting and magnetic separation at minus 325 mesh, 28 composites produced concentrates that contained an average of 66.0 percent iron with less than 10 percent silica. Recovery of contained iron was over 90 percent. Natural magnetic material in excess of 5 percent was present in 142 composites. Trial flotation tests were used to evaluate three samples unresponsive to reductive roasting and magnetic separation procedures, and satisfactory concentrates having low silica contents (averaging 6.6 percent) were achieved.

Jan 1, 1965

By Eric Cather

A mineral investigation of prospects in the Sawtooth Mountains B Wilderness Study Area (WSA) by the U. S. Bureau of Mines in 1983 revealed none had mineral production, resources, or development potential. The area is underlain by tonalite and smaller amounts of schist, One developed prospect and one prospect pit are in the WSA. They are in schist similar to host rock which has yielded gold in nearby mining districts, Sand and gravel deposits in the WSA are large but too far from markets to be considered resources. No energy (oil, gas, coal, or geothemal) resources were identified in the USA.

Jan 1, 1984

By R. D. Leitch

The work of the United States Bureau of Mines on stream pollution3 by coal-mine drainage has included a study of seasonal variations in acidity and volume of several streams in Pennsylvania. The acidity of these streams has been determined during the two or three years prior to 1930 and the results may be considered to represent "normal" low water conditions. The summer of 1930, however, was unusually dry and represents what may be termed "extreme" low water conditions on these streams. This report is a comparison of the results obtained for extreme low water of 1930 and for other years. The streams investigated were Buffalo Creek in Somerset County, Indian Creek (lower 5 miles) in Westmoreland County, Little Toby Creek in Elk and Jefferson Counties, Daguscahonda Run in Elk County and West Creek in Elk and Cameron Counties. These will be treated separately in the order given. Most of the descriptive matter and physical data pertinent to the streams and drainage basins are taken from published reports of the Pennsylvania State Water Supply Commission, 1917.4

Jan 1, 1931

By A. F. Baker

Tests were conducted in commercial foundries to determine the suitability of calcined anthracite as a cupola fuel. The calcined anthracite performed satisfactorily at two of the three foundries where iron-melting tests were conducted. Performance at the third installation was unsatisfactory because metal temperatures deviated widely and, in general, were lower than is desirable for the type of castings being made.

Jan 1, 1963

By W. C. McBee

Technology for the preparation of densifiable sulfur concrete (sulfapave) materials has been devised by the Bureau of Mines. The materials are intended as new construction materials for use in corrosive areas where conventional materials fail. A series of modified sulfur cements were developed, which can be used in combination with dense-graded aggregates to prepare sulfapave materials with excellent corrosion-resistant properties. The materials can be mixed, laid, and compacted into place with conventional hot-mix asphalt pavi.ng equipment. Mixture designs utilizing 5-to 30-pct-modified sulfur cements and dense-graded aggregates gave material properties ranging from rigid to flexible. Laboratory corrosion tests in sulfuric acid showed no material loss or deterioration of physical properties over a 1-year test period in concentrations ranging from 0 to 60 pct at ambient temperatures. Preliminary results on field testing the materials for durability to weathering, corrosion, and traffic have been excellent, with no evidence of failure in the materials.

Jan 1, 1985

By D. J. Judy, D. J. Rabovsky, W. H. Pailes, V. Castranova, K. Van Dyke, J. Rabovsky, N. A. Sapola, M. McPeek

"Platelet activating factor (PAF) can be released from pneumocytes following exposure to occupational dust (Am. Rev. Respir. Dis. 135:83, 1987). In addition, PAF has been shown to induce pulmonary inflammation, edema, and bronchoconstriction (Hosp. Prac. 19, 67, 1983). This investigation reports the effects of PAF on the properties of three types of cells found in the lung. PAF (1-100, K1/2 = 2.5 pH) caused depolarization of neutrophils as well as generation of chemiluminescence and secretion of hydrogen peroxide. These responses were dependent on the presence of extracellular sodium. However, PAF did not alter oxygen consumption of neutrophils. Although PAF (10 uM) caused depolarization of alveolar macrophages, no stimulation of chemiluminestence, superoxide secretion, or oxygen consumption was observed. However, PAF (10 uM). did potentiate chemiluminescence and superoxide secretion in response to zymosan (2 mg/ml) by 55% and 36%, respectively. In addition, PAF (10-90 uM) caused aggregation of alveolar macrophages. PAF (2-10 uM) also caused depolarization of type II cells, but did not affect membrane integrity or oxygen consumption. However, PAF (10-18 PM) enhanced the activities of two distinct forms of cytochrome P-450 in type II cells and caused aggregation of type II cells at PAF doses above 18 uM. These data indicate that PAF can affect the secretory activity of pulmonary phagocytes and the ability• of type II cells to detoxify foreign compounds (Bureau of Mines Grant - G1175142).INTRODUCTIONPlatelet activating factor (PAF) is a glycerophospholipid (1-0-alkyl-2-acetylsn-glycerol-3-phosphoryl choline) which has been shown to Mediate a broad range of biological activities (1-3). Its pulmonary actions include contraction of pulmonary tissue (4), secretion of leukotrienes from leukocytes (5), airway constriction (6), pulmonary edema (7), and enhanced migration of neutrophils into the airspaces of the lungs (8,9).PAF can be released from several different cell types, such as, basophils, neutrophils and alveolar macrophages, in response to a variety of particulates or membrane stimulants which include zymosan, calcium ionophore, phorbol esters, chemotactic agents, and endotoxin (10-13). Therefore, PAP may play an important role in the development of pneumoconioses by mediating pulmonary responses of lung cells to a variety of occupational dusts. To investigate this possibility, we determined the effects of PAF on several physiological parameters of neutrophils, alveolar macrophages, and alveolar type II epithelial cells."

Jan 1, 1988

By George L. Gates

This report presents is an evaluation by the Federal Bureau of Mines of the effect of clay-water, brine, and oil-base drilling fluids on the productivity of test wells drilled on the Umiat anticline in U.S. Naval Petroleum Reserve No. 4 in northern Alaska. Eleven, wells were drilled on the Umiat structure as part of the U.S. Navy's extensive exploration of the Reserve during 1944-53 to determine the possibilities for oil production. The Federal Geological Survey cooperated in the exploration program and has published a comprehensive report3/ on the geology of the area and case histories of the wells. The re¬port also includes the results of special studies by the Bureau in connection with the drilling and coring of well 9 with oil-base mud in hole and was the source of much of the information used in preparing this publication. Of the eleven wells, four were drilled with rotary tools and water-base mud (one of the water-base muds was an oil-in-water emulsion mud), five were drilled with cable tools with brine in the hole, one was drilled with cable tools with brine in the hole and later reamed with rotary tools and crude oil, and one was drilled with rotary tools and oil-base mud. Although all of the wells penetrated sandstones that contained oil and gas, some were productive and others were not. The latter two wells, one completed with crude oil in the hole (with some added brine) and the other with oil-base mud, had the greatest productive capacities. The wells drilled with cable tools and brine in the hole had lower productive capacities. In contrast, two of three wells completed with rotary methods and fresh-water drilling mud and the well com¬pleted with rotary and emulsion mud were unproductive.

Jan 1, 1960