Search Documents

By W. E. Anable

The Bureau of Mines studied the purification of commercially available yttrium by melting it in a 100-kw electron-beam furnace. Button-scale melts were made to determine the ultimate purification that could be attained by melting yttrium at 1,733° to 1,770° C at low pressure (0.05 to 0.1 micron) for 1 to 120 minutes. In addition, numerous melts were made to study the effect of doping yttrium with carbon, 17 selected metallic additions, and 3 compounds. Except for nickel and zirconium, the metallic impurities in yttrium were lowered significantly on extended treatment; silicon was lowered only slightly. The nonmetallic impurities} oxygen, nitrogen, and carbon, were not lowered except on short exposures. In isolated instances, the oxygen content was lowered from 5,860 ppm to about 5,000 ppm. In most instances the carbon con-tent was lowered from 545 to about 220 ppm in 20 minutes and then increased again. It was concluded that yttrium cannot be purified by direct heating or by the doping technique employed.

Jan 1, 1965

By A. J. Barry

A practical method has been developed and field tested which provides an estimate of the bearing capacity of mine roof and floor. The relationship between penetration of the strata and imposed loads is determined by in situ tests. Information of this type is needed to determine the maximum allowable pressure that may be applied by self-advancing supports on roof and floor of a longwall face without causing a punching type of failure.

Jan 1, 1970

By T. T. Read, T. L. Joseph, F. H. Royster

In a preliminary study of the beneficiation of iron ores conducted by the Bureau of Mines, one of the authors (T. T. Read) found it necessary to ascertain, if possible, how much effect a decrease in the silica content of an iron ore has upon the cost of making pig iron from the ore. In the beneficiation of iron ores the most important impurity to be removed is usually silica, and the amount that can be expended on a beneficiation process to reduce the silica content of the ore is obviously determined by the amount of increase in the value of the ore after beneficiation. The price that can actually be obtained for a beneficiated ore is, of course, a matter of negotiation between the seller and the buyer, but since the relative value of different grades of iron ore must be chiefly based upon the cost of making pig iron from them, an approximation as to the effect which decrease in the silica content of ore has upon the cost of snaking pig iron is an important guide in estimating what probable average gain will result from subjecting an ore to a beneficiation process. A search of the literature failed to reveal any detailed statement on this important topic, but fortunately the data are at hand to permit making an approximate calculation of the probable effect. For the purpose of the calculation assume three iron ores with the following composition (natural):

Jan 1, 1924

By J. A. Organiscak

The Bureau of Mines recently investigated dust generation and methane liberation during half-and full-web cutting at a double-drum shearer longwall face. This study was conducted to ascertain the health and safety aspects of wider web shearing at longwalls. Results from these underground tests showed that deeper web cutting reduced dust generation and methane liberation per ton of coal mined, while significantly improving shearer production rates. When cutting with the airflow (head-to-tail cut pass) full-web cutting decreased dust generation per ton by 16 pct at the shearer and 6 pct at the tailgate, with an increase in shearer production rate of 72 pct. Methane liberation per short ton also deere~sed by 36 pet at the shearer and 22 pct at the tailgate. Full-web cutting against the airflow (tail-to-head cut pass) decreased dust generation per ton by 41 pct at the shearer and 37 pct at the tail-gate over half-web cutting, with an increase in shearer production rate of 61 pct. Methane liberation per ton also decreased by 35 pct at the shearer and 41 pct at the tailgate. These improvements for full-web cutting are a reflection of improved cutting efficiency (less dust and methane produced from cutting) and less new face area exposed per ton of coal mined (less methane liberated from face per short ton of coal mined).

Jan 1, 1988

By Fred D. DeVaney

Copper sulphate is a common flotation reagent for blonde ores. Metallic iron also is present in the mill circuit, and a reaction between the iron and the salt would be in accord with well-known chemistry. The abundance of metallic iron in a flotation food may be noted by even perfunctory examination. First of all the mine contributes metallic iron, then the coarse-crushing machines add their share, and finally the fine-grinding medium its portion. If the grinding is with cast-iron balls the amount of metallics is greater than when steel is used. Thus it, is that much more metallic iron is present than would be indicated by noting the ball consumption. An estimate that the total amount of metallics is twice that supplied by the balls and liners might not be far amiss. That copper sulphate plates out on iron in an acid solution is well known, but since flotation is practiced commonly in solutions where acid has not been added this reaction has not been given sufficient thought.

Jan 1, 1929

By Thomas M. Garland

A field study was made by the Bureau of Mines in cooperation with oil companies to determine the feasibility of changing the injection profile of water-input wells after water breakthrough at producing oil wells. A secondary objective was to study the particle size and quantity of plugging material required to change the input profile and the methods of applying these materials. Fifty-three injection wells were treated with various amounts and types of plugging materials and the injection profile was definitely changed in most of the wells treated. Increased efficiency of water injection after treatment was indicated by tracer surveys and injection-well performance. There were some indications that the rate of water production was reduced and the rate of oil production was increased as a result of selective-plugging treatments, but ,s found that an immediate change in the rate of oil and water production did not normally occur. In many cases, beneficial results from a treatment may never be observed in the rate of oil or water production due to the many factors that affect the performance of producing and injection wells.

Jan 1, 1966

By J. A. Ruppert, P. M. Sullivan

A study was made of filtration techniques for recovering the major part of the tin contained in iron - tin alloys known as hardhead . Special smallscale filtering apparatus and a three - stage cyclic process were developed . Eighty- seven percent of the tin contained in an alloy of 82 percent tin and 17 percent iron was recovered as pure metal by pressing at 975° C followed by a second pressing at 800 ° C and a final filtering at 250 ° C. Small amounts of Sb , Cu , and Fe impurities were removed by adding Al to the molten product and performing another filtration at 250 ° C.

Jan 1, 1964

By M. M. Fine

This Bureau of Mines report describes the theory, experimental procedures, and the results obtained to date in the development of the Bureau's process for magnetically roasting iron ores using scrap iron as a means of reduction. Since magnetic separation is an operational step common to magnetic taconite plants, the preliminary research studies emphasized only the novel magnetic roasting step. The studies included the use of automobile scrap, ferrous reductants such as borings and turnings, and prereduced pellets. Technical feasibility of the process was demonstrated both on a bench- and pilot-scale. Quality magnetic concentrates with recoveries of over 90 percent were obtained from a direct shipping ore containing 59.5 percent Fe and from fine grained semitaconites with about 30 percent Fe.

Jan 1, 1966

By Raymond W. Hiteshue, Sam Friedman, Martin D. Schlesinger

The Bureau of Mines in cooperation with the El Paso Natural Gas Co. investigated the effect of high temperature and pressure at short residence times on the hydrogenation of a New Mexico coal to gaseous and liquid hydrocarbons . The study was made in a bench - scale semicontinuous unit at pressures of 500 to 6,000 psig , 480 ° to 1,000 ° C , and residence times of less than 1 minute to 15 minutes . Ammonium heptamolybdate was impregnated on the coal to furnish 1 percent molybdenum based on maf coal . Coal could be rapidly hydrogenated at elevated temperatures and pressures to yield large quantities of gaseous hydrocarbons and small quantities of lowboiling oils , high in single - ring aromatics . At 800 ° C and 6,000 psig and a residence time of 1 minute , the yield of hydrocarbon gas was 43 percent and of liquid hydrocarbons 9 percent , based on maf coal . With a 15 - minute residence time , the yield of gaseous hydrocarbons increased to 68 percent with a decrease in yield of oil to 6 percent . At higher hydrogen velocities , the yields of oil were much greater but contained large quantities of asphaltene . Low concentrations of molybdenum (0.01 and 0.1 percent ) or a high concentration of iron ( 1 percent ) were ineffective at 800 ° C , 6,000 psig , and short residence time .

Jan 1, 1964

By C. W. Vierrether

Tailings from the Pea Ridge iron mine contain significant amounts of apatite, which has rare-earth element values associated with it. In association with the recovery of rare-earth minerals as a secondary resource, the U.S. Bureau of Mines conducted an investigation on the recover ability of the rare-earth minerals from these tailings. The mill tailings were subjected to a phosphate flotation to separate the apatite from other constituents. More than 70-pct recovery of the rare-earth values was achieved. Based on mineralogical characterization and prior analysis of rare-earth-bearing breccia pipe material at Pea Ridge, it is proposed that processing this phosphate concentrate on a vanner table would yield up to a 95-pct recovery of the rare earths in the concentrate, with the apatite reporting to the tailings. Intensive ore microscopy studies of the original tailings to the flotation products led to the identification of monazite, xenotime, and rare-earth-enriched apatite as the major rare-earth-bearing minerals in the tailings.

Jan 1, 2010

By Margaret R. Egan

The Bureau of Mines subjected three commercially available brands of transformer fluid to a series of combustion studies. The experiments were conducted in the intermediate-scale fire tunnel, which was designed to simulate environmental conditions in underground mines. The work was divided into three phases. In phase one, the brands were compared for gas production, smoke characteristics, and combustion yields. In phase two, the production constants of transformer fluids and other fuels were compared for the rate of formation of gas and smoke as a function of fire size. In phase three, several diameters of liquid-pool fires were compared in terms of fire size and burning rate. These transformer fluid measurements will be added to the existing coal and wood data that can be used as a basis of comparison for future studies of other mine combustibles. Further research into the combustion product emissions from combustible materials found in underground mines will lead to improved and realistic fire detection and suppression systems,

Jan 1, 1986

By T. M. Romslo

"INTRODUCTION This report presents factual data obtained by the Bureau of Mines in the course of an investigation of the Antler mine in the Cedar Valley mining district, Mohave County, Ariz.The Antler property was first examined by Thomas L. Chapman, mining engineer, Bureau of Mines, on December 18, 1943, and January 28, 1944. In June 1945, A. H. Wadsworth, Jr., and R. L. Griggs, geologists, Federal Geo¬logical Survey, examined the Antler mine and several other mines in the district. Both Chapman and Wadsworth recommended diamond drilling of the Antler property to determine the character and extent of ore deposition.In October 1946, the surface and underground workings were surveyed by George Huseman, Mining engineer, and T. M. Romslo, project engineer. The following month Eldred. D. Wilson, geologist of the Arizona Bureau of Mines, assisted by the project engineer, mapped the geology. Subsequently trails were built to drilling sites and diamond drilling started January 16, 1947. The project was completed April 25, 1947.ACKNOWLEDGMENTSIn its program of investigation of mineral deposits, the Bureau of Mines has as its primary objective the more effective utilization of our mineral resources to the end that they make the greatest possible contribution to national security and economy. It is the policy of the Bureau to publish the facts developed by each project as soon as practicable after its conclusion. The Mining Division, Lowell B. Moon, chief, conducts preliminary examinations, does the actual investigative work, and prepares the final report. The Metallurgical Division, O. C. Ralston, chief, analyzes samples and takes beneficiation tests."

Mar 1, 1948

By J. K. Whyatt

Assuring ground control safety in many mining and tunneling projects depends, at least in part, on an understanding of in situ stress conditions that will be encountered. Yet it is rarely practical to conduct more than a very limited number of stress measurements. Stresses along the route of a proposed excavation are typically interpolated from available measurements, often assuming a linear variation of stress with depth (or elevation). However, projects where multiple stress measurements are conducted often report more complex variations of in situ stress, usually in apparent relationship to geologic structures. These structures often include lithologies of contrasting elastic properties. A method is proposed for estimating stresses in these cases by first back-calculating regional loads from available stress measurements and then modeling the distribution of stress throughout the rock mass. The method has been successfully applied to a set of in situ stress measurements from the Coeur d’Alene Mining District of northern Idaho, USA. Results provided new insights into district stress conditions and the distribution of rockburst hazards along mine drifts and between various mines. This success should transfer readily to suitable deep tunneling projects.

By R. H. King

A very simple cold-bend test was devised and tested for evaluating thermoplastic jackets used on mine-power-feeder cables. A test sample is bent into a semi-circle whose radius is equal to the minimum bend radius recommended by IPCEA and then cooled to the, desired test temperature (-35°C). While at temperature, the sample is straightened by pulling the cable ends with a winch arrangement. The results show that of the jackets tested, those which cannot withstand the test literally burst when the sample is straightened.

Jan 1, 1978

By W. L. Staker

The Bureau of Mines investigated the use of shredded automobile scrap for copper cementation. Air agitation was used to improve the cementation rate and prevent excessive buildup of copper on the iron. The pieces of scrap were too large to be properly evaluated in the laboratory; therefore, a pilot scale test unit was constructed and the process tested at field locations. Pregnant solution was obtained from industrial leaching operations, processed in the test unit and the barren solution and cement copper were returned to the plant process stream. The test results showed that the air-agitated launder containing auto-mobile scrap was an effective means for recovering copper from leach solutions. A continuous l4-day test run was made without a noticeable decrease in cementation efficiency. The most suitable scrap product was obtained from incinerated automobile hulks shredded in a hammer type of shredder. However, it was necessary to remove small pieces such as nuts and bolts because they interfered with the discharge of the copper product.

Jan 1, 1976

By Robert W. Geehan

"INTRODUCTION The Bureau of Mines has been investigating deposits of critical and essential minerals in the United States since 1939. Many of the mines were developed.A preliminary examination of the Sultan mine was made in January 1945 by the author, who recommended investigation by drifting and crosscutting. The Bureau conducted a project at the mine from April to June 1946. Claims investigated are in sec. 20, T. 25 S., R. 58E., Mount Diablo base and meridian, in southern Clark County, Nev., about 7 miles southwest of Good-springs.The Sultan mine has been an intermittent producer of zinc-lead-silver ore since 1910. During World War II, ore was shipped to the Government stock pile at Jean, Nev., and to the International Smelting& Refining Co.'s smelter near Salt Lake City, Utah. Throughout the past year, ore has been milled and the concentrates have been shipped to the smelter."

Sep 1, 1947

By Henry E. Perlee

Air compressor explosions that are caused by the ignition of combustible vapor mixtures cannot be explained by a single reaction mechanism or sequence of events. Explosions have been caused by the sudden release of large quantities of lubricating oil, by the rapid vaporization of oil that had accumulated slowly in high-pressure piping, and by the production of decomposition products from carbonaceous deposits. Ignitions can be caused by the heat produced in a catalytic reaction, in a compression process, or when a shock wave is propagated through a combustible vapor-air mixture. The frequency of these ignitions can be minimized by establishing proper maintenance and cleaning schedules. Further study is needed to satisfactorily correlate the various factors involved in compressor explosions.

Jan 1, 1963

By H. Kenworthy

The objective of this investigation was to evaluate the technical feasibility of smelting certain low-grade domestic iron ores in an electric furnace. Laboratory-scale experiments showed that a high recovery of iron in the form of pig iron can be obtained from east Texas ores containing less than 25 percent iron. The pig iron was amenable to standard-or electric-furnace-refining methods for producing steel. Car-bon, silicon, and phosphorus were the primary impurities removed in refining. Overall recoveries of iron as pig iron exceeded 95 percent, in contrast with commercial mineral-dressing recoveries on these particular ores of 50 percent of the iron as a 45-to 50-percent iron concentrate.

Jan 1, 1958

By W. E. Wallace, C. A. Hill, M. J. Keane

"Diesel exhaust particulate material from exhaust pipe scrapings of two trucks, diluted automobile diesel exhaust particulate material collected on filters, and two oil shale ores were prepared for the Ames mutagenrcity assay by dichloromethane OOP ex¬traction, by dispersion into 0.85% saline, or by dispersion into dipalmitoyl lecithin (DPL) emulsion in saline. Salmonella typhimunum TA98 was used to detect frameshift mutagens in the samples. Samples of diesel soot gave positive mutagenic responses with both DCM extraction and DPL dispersion, with the DPL dispersion giving higher results in some cases. The results suggest that possible mutagens associated with inhaled particles may be dispersed or solubilized into the phospholipid component of pulmonary surfactant and become active in such a phase.INTRODUCTIONThe Ames Salmonella/microsome assay (Ames et al., 1975) has been shown to be a useful test for detecting genotoxic properties of various agents. Hundreds of specific chemicals have been screened (McCann et al., 1975), and the test has been applied for many types of environmental samples. Airborne mutagenic agents, for example, have been found in urban air (Chrisp and Fisher, 1980; Hughes et al., 1980; Ro· senkranz et al., 1978), in diesel engine exhausts (Huisingh et al., 1978), and in the by-products of coal combustion processes (Chrisp et al., 1978).Samples of airborne particles are typically collected on membrane filters, and undergo a rigorous extraction procedure with organic solvents and/or ultrasonic agitation (Clark and Hobbs, 1980). Often extracts are transferred to another solvent that is compatible with the assay system. These extraction procedures, while efficient from an analytical perspective, are not physiologically plausible. The questions that present themselves are whether a demonstrated mutagen can be taken up in vivo and whether the process is quantitatively or qualitatively different from the above laboratory procedure (Wallace et al., 1984).When a particle of respirable size is inhaled to the alveolar region of the lung, its first physiological contact is with pulmonary surfactant that lines the inner surfaces of the alveoli. This surfactant is an aqueous fluid containing proteins, phospholipids, and other components (R. J. King, 1982). The principal phospholipid constituent is L·alpha-phosphatidylcholine, beta,gamma-dipalmitoyl, or dipalmitoyl lecithin (OPL) (l. C. King et al., 1981)."

Jan 1, 1989

By R. J. Leary

The natural gas-air burner described in this report was designed and constructed to meet the thermal requirements of a convective process for heating steel scrap. This process involved downward combustion of natural gas with air, blending the combustion products with diluent air, and then passing this tempered stream of gases downward through a porous bed of steel scrap contained in the furnace chamber. The scrap would be heated to a temperature limited by the adiabatic flame temperature of the gas stream in a period that depended on the rate at which heat was supplied per unit of bed cross section. The temperature of the gas stream would be limited to that beyond which an objectionable degree of oxidation would occur; for carbon steel this limit had been found to vary from 1,900° to 2,100° F. with the superficial velocity of the gas stream. The productivity of the process was dependent on the rate of heat input per unit of furnace cross section; for the 3-foot-diameter experimental furnace an input of 680,000 B.t.u. per hour was desired. The burner described was designed to meet these conditions of temperature and heat input. It provided for three streams of entering gases: (1) A primary air-fuel mixture too rich to be combustible, that is, above the upper flammable limit; (2) secondary air for combustion of the primary mixture; and (3) tertiary air, principally for cooling the combustion products to the temperatures desired for process operation. Downward combustion of the primary and secondary streams occurred in a flame stabilized on an annular port, while tertiary air flowed in an annular path surrounding the port and also through an axial channel whose wall formed the inner ring of the annular port. This burner performed beyond the designed heat-input rates while producing stable flames, which were adjusted readily to the temperatures desired. Gas-stream temperatures were easily controlled to within 15° F. of the desired value by simple manual adjustment of the flow valves.

Jan 1, 1959