Search Documents

By J. Bender

The objective of this research was to (1) Further develop cyanobacteria mats' for metal-tolerance and cold-tolerance, (2) test them for durability in the field environment and (3) assess them for metal sequestering potential with actual and simulated field samples. Results show that mats performed well In the field and effectively sequestered metals from actual and simulated field samples. Metal uptake from Iron Mountain Hine samples was for Ins 87%, Cu and Cd 99%, Initial concentrations (mg/L) were Zn = 3,250, Cu , 279, Cd = 28. In solutions simulating the Gulf Tunnel drainage, Zn and Mn were effectively removed by mats immobilized on glass wool. Effluent water, after treatment, generally had a Ph of 7 .5-8.5. Al though the final metal concentrations in the mats 'harvested from the decontaminated water were only 1% or less, the actual mechanism of metal deposit was probably a mat-mediated alteration of the environmental conditions causing the metals to deposit outside the mat as oxides or carbonates. Bioflocculents, released by the mats, were likely involved in the metal-removal process.

Jan 1, 1996

By Richard G. Burdick

The Bureau of Mines conducted this research to determine the feasibility of using soil redox measurements, a relatively new method in mining geophysics, to locate or define a variety of conditions that are hazardous or otherwise of interest to the mining industry. The method was used in three widely separated areas in an attempt to de- fine subsurface concentrations of methane, the edges of coal-burn areas, and a hydrothermal vein set. Both a description of the method used and test cases are given in this report.

Jan 1, 1982

By Jeffery M. Listak, Ernest A. Curth

"It took only 9 years from the first appearance of roof shields on the U.S. longwall mining scene to the present predominance of shield faces. An apparent consequence is the welcome downward trend in accidents related to failures in longwall ground control. The report addresses load prediction, the effects of shield geometry on support loads, factors contributing to ground control, and related techniques. The Bureau of Mines took an active part in the evolution of longwall mining, including developing one of the first shield faces in 1975, the first lemniscatetype shields in 1976, the Mine Roof Simulator completed in 1980, the first shields in steeply pitching coalbeds in 1981, and the first multilift working of a thick coalbed in 1982. The information offered in this state-of-the-art report will assist in establishing criteria for roof support selection. INTRODUCTIONIn terms of roof support technology, the introduction of shields in the seventies and eighties was a major step forward. Table 1 indicates the predominance of shield faces on the U.S. longwall mining scene and its apparent consequence, a welcome downward trend of ground-control related accidents.The rapid progress of longwall technology began in 1975 and is highlighted by a development leading from the caliper shield to the modern lemniscate type. Shields have been gaining preference over chocks since their advent to longwall mining in 1975. Safety and productivity factors favoring shields over chocks are--1. A sheltered working space requiring minimum cleanup work.2. Structural stability that allows advancing without delay even with brushing roof contact and, by controlling all lateral loads, removing the requirement for cumbersome leg restraint and restoration devices.3. Wide hydraulic range of mining height.The development of roof shields in the Federal Republic of Germany preceded and paralleled their rapid adoption by U.S. miners. In 1983, 87 pct of the total production in Germany came from shield faces (1).2 In Great Britain, the National Coal Board introduced the first shield support system in 1977 to initiate Advanced Mining Technology (ATM) and Heavy Duty Mechanization (HDM) programs; as of mid-1982, 44 shield faces were operating, or 7.5 pct of a total of 581 faces CJ_)."

Jan 1, 1985

By Harry R. Johnson

Laboratory experiments were conducted to study the carbon deposition characteristics of a high-gravity, paraffin-base crude oil. The results of these experiments indicate that a fuel supply adequate to initiate a combustion wave can be deposited in high-gravity-oil reservoirs. These results are significant because there has been considerable doubt whether oils over 35° API gravity are able to deposit sufficient fuel. Considered in these studies were the effects of air flux, temperature, initial oil saturation, and time on carbon deposition. Conditions that maximized carbon deposition in the laboratory and an understanding of the nature of carbon formation are shown by graphical interpretation of the data. Statistical techniques were used to design and analyze the results of the retort tests. For the same amount of laboratory work, this approach yields more information about the systems that were studied than the classical method of research presently used in many laboratories. In addition, the accuracy of calculating the effect of each variable on carbon deposition is twice that of the classical approach. This paper develops the statistical approach to research without complex mathematics, thus enabling the reader to grasp the concept of how statistics can be applied to study many complicated problems.

Jan 1, 1966

By H. O. Poppleton

This Bureau of Mines study was made to investigate a possible method for selectively removing the Si02 component of silicate minerals and ores. Of specific interest were aluminum ores and zircon. Methods are described for removing Si02 from these ores as volatile silicon sulfides by treating the ore with sulfur and carbon; with sulfur, carbon, and a reducing gas; or with sulfur compounds and carbon. Comparative results are also given for the desilication of some of the ores with carbon alone to form volatile silicon monoxide. The silica component can be removed partially from bauxites at temperatures above the sublimation temperature of SiS (940° C) by treatment with carbon, sulfur, and methane; however, it is more difficult to remove the silicon from kyanite, manganese silicate, red muds from aluminum processing, kaolinite, lateritic nickel ores, and zircon. Complete desilication requires temperatures ranging from 1,100° C for bauxite to 1,450° C for zircon. Although the high temperatures required and the undesirable metal sulfides produced eliminate practical application of this method using present technology, the Bureau is reporting this data so that they will be available to future investigators.

Jan 1, 1974

By Guy A. Johnson

The Bureau of Mines, through research and development contracts with the FMC Corp., has developed and tested two automatic fire sensing and suppression systems for large haulage vehicles. This work was undertaken to enhance driver safety, to lessen substantial property damage from fires on large trucks, and to increase the vehicle operator's productivity. One automatic truck fire protection system protects both the engine compartment and brake rid areas, while the second system is used in the engine compartment and fuel tank area. Both systems have redundant fire-sensing capabilities and manual override controls. Upon sensing flames and/or heat, the systems suppress the fire with pressurized, E-C class dry chemical. Both fire protection systems are flexible in design and can be modified for use on other mobile minim' equipment. Prototypes of both systems have been subjected to long-term, in-mine validation testing and actual Eire tests on 100-ton-capacity trucks at the Puma mine near Tucson, Ariz., and the Erie mine at Hoyt Lakes, Minn. During the 4-month endurance test of the first system at Pima, an accidental flash fire occurred in the test truck while it was working in the pit. The system successfully sensed and automatically extinguished the fire with no injury to the driver and little damage to the truck.

Jan 1, 1975

By H. E. Powell

The smelting of brass and bronze generates a dust composed primarily of zinc oxide, with lesser amounts of other metal oxides, such as copper, lead, and tin. The small quantity of this waste generated by individual smelters and the relatively low unit value of the contained metals, suggests the desirability of reclaiming the metals onsite or at some nearby point. The Bureau of Mines has developed a process that fits these requirements. The technique consists of (1) dissolving zinc and copper from the dust with sulfuric acid, (2) recovery of copper by cementation, (3) recovery of zinc as zinc sulfate crystals, and (4) recovery of lead and tin as a salable residue. Alternatively, zinc may be recovered by electrodeposition. Free acid is recycled and no major pollution problems are generated by the process.

Jan 1, 1972

By D. Harrington

While apparently the hysteria with regard to silicosis and other occupational diseases has largely subsided and this subject is being more carefully considered and soberly judged, it would be poor policy for any employer to maintain that the storm has ended and that he can relax and revert to conditions as they were 5, 10, or more years ago. The fact is that the plan of paying occupational-disease compensation is now in its infancy and can be expected to grow rapidly. At present, while all of the States of the Union, including the District of Columbia and excepting only Arkansas and Mississippi, have compensation acts, only the following make provision for occupational diseases to some extent or in one way or another: California, Delaware, Connecticut, District of Columbia? Illinois, Indiana, Kentucky, Massachusetts, Michigan, Minnesota, Missouri, Nebraska, New Jersey, New York, North Carolina, North Dakota, Ohio, Pennsylvania, Rhode Island, Washington, West Virginia, and Wisconsin. Silicosis is compensable in one way or another in California, Connecticut, District of Columbia, Illinois, Kentucky, Massachusetts, Missouri, New York, North Carolina, North Dakota, Ohio, Pennsylvania, West Virginia, and Wisconsin, and possibly in other States. During the past few months, occupational-disease legislation (largely silicosis) has been considered in some form in Arkansas, California, Delaware, Idaho, Maryland, Kansas, Massachusetts, Michigan, Minnesota, Montana, Nebraska, New Jersey, Ohio, Pennsylvania, Tennessee, Utah and Washington. It will be surprising if comparatively comprehensive occupational-disease legislation is not on the statute books of nearly every State in the Union within the next 5 years. With this situation confronting him, the farsighted industrialist who has the interest of his organization at heart, if he has not already done so will immediately start to "put his house in order" by studying possible occupational disease hazards to his employees and promptly applying known remedial measures or attempting to devise such measures if none exist. Unquestionably, one of the most important of the surveys to be made relates to dust occurrence, as State laws on occupational disease are almost certain to contain provisions, on silicosis and, with almost equal certainty, the provisions of any State law are not likely to be particularly similar to those of other States.

Jan 1, 1938

By D. A. Reynolds, L. P. Rockenbach

"The method of analyzing light oil for benzene is fully described by Fieldner and others 4/ and Kester and Kolmes 5/. In this procedure, benzene is determined by shaking 20 cc. of the 79º to 81º C. boiling point cut from the fractionation of the refined light oil with 3 volumes of 98—percent sulfuric acid in an A. S. T. M. separator funnel of the type used for determining water in bitumi¬nous materials. After the mixture has been shaken 5 minutes it is allowed to settle at least half an hour and the acid is drawn off; the residual oil is reported as paraffins and the decrease in volume as benzene. The method has been found satisfactory for light oils from coals carbonized at 5000, 600°, and 7000 C. but does not give accurate, reproducible results for oils from the 800° C. tests.The content of benzene of the 790 to 81° C. cut is high, 90 to 95 percent, for 800° C. light oils, whereas for lower—temperature light oils it is considerably less. Benzene is the most difficult of the aromatics to sulfonate, hence the acid concentration must be maintained above 95 percent to insure complete sulfonation. Sulfuric acid (98 percent) reacts with benzene, but its reaction with paraffins at ordinary temperatures is negligible; however, more concentrated acid will attack paraffins and give erroneous yields of benzene. The reaction between benzene and sulfuric acid forms water that will dilute the acid. The effect of this dilution may be overcome by increasing the acid-to-oil ratio or increasing the strength of the acid. The latter, however, must not be used, because the stronger acid reacts with paraffins."

Mar 1, 1942

By J. B. Littlefield

The Greenburg-Smith impinger was developed at the Bureau of Mines in cooperation with the United States Public Health Service in 1922 in the course of an investigation of dust-sampling instruments available at that time. Although it is not used extensively outside of the United States, it is now soused in this country to collect samples for the determination of any dustiness, and most of the information correlating degree of dustiness with physiological effect has been obtained by the impinger method. The chief disadvantages in the use of the regular impinger, especially in mines and other places accessible with difficulty, are its bulk, weight, and power requirements. It requires a source either of electricity or of compressed air, which necessitates connections and extension of existing supply lines to each sampling point; the only alternative is the use of a relatively large pump hand-operated with considerable effort.

Jan 1, 1937

By Harry W. Campbell

U.S. Bureau of Mines investigation; identified no mineral resources or evidence of mining activity in the Sheep Divide RARE II area. A deposit 10 mi (16 km) southwest of the area contains copper and silver minerals in the Triassic Wild Sheep Creek Formation which probably underlies basalt lava flows covering the study area. Abundant basalt in the area can be crushed and used as aggregate, but suitable deposits closer to markets are widely available No sand, gravel, coal, oil, gas, or geothermal resource, were Identified. INTRODUCTION Location and Access The Sheep Divide RARE II area [10 mi (16 km) west of the Snake River] encompasses 7,100 acres (2,800 ha) of the Hells Canyon National Recreation Area in the Wallowa-Whitman National Forest. Enterprise, Oregon, is located 23 air mi (37 (m) west of the area. Peripheral access is provided by the highway from Joseph to the community of Imnaha, Oregon, then south to the study area by the graveled Upper Imnaha Road (fig. 1).

Jan 1, 1983

By Walter R. Storms

This paper, which describes the mining methods of the Potash Co. of America in Eddy County, N. Mex., is one of a series being prepared by the Mining Branch, of the Bureau of Mines on mining practices and methods in various mining districts of the United States. 4, T. The mine and plant of Potash Co. of America are situated in sec. 20 S., R.. 30, E.,. N. M. P. M., about 22 miles by paved road northeast of Carlsbad (fig. 1). A spur line of the Atchison, Topeka & Santa Fe Railroad also connects the mine with Carlsbad.

Apr 1, 1948

By C. J. Walker

The Bureau of Mines undertook a theoretical and laboratory study to determine the feasibility of using ethylene as a tracer for natural gas in underground gas-storage reservoirs. The study indicated that ethylene was a useful gas tracer in underground gas storages. Tracer losses were not excessive. Laboratory tests were conducted at pressures as high as 500 psia in both wet and dry consolidated-sandstone cores, evaluating tracer loss with gas blends containing natural gas with different concentrations of ethylene tracer. Under certain conditions losses were less than 17 percent.

Jan 1, 1966

By W. D. Haselton

This paper dealing with the mining methods used in producing iron ore from an underground operation located in the central-western part of the Mesabi Range in Minnesota is one of a series being prepared by the Bureau of Mines on mining practices, methods, and costs in the various mining districts in the United States. The mine here discussed was laid out in accordance with a plan adapted to a rather unusual type of ore body, the nature of which is such that the mining method necessarily differs in certain respects from the method used at most of the mines in this district. A description of it may therefore be of interest.

Jan 1, 1930

By John R. Bartels

In laboratory testing, the Bureau of Mines established criteria by which common resin-grouted roof bolting systems can be evaluated and compared. Ultimate strength and stiffness were determined for nonten-sioned full-column, point-anchor, tensioned full-column, and debondable resin-grouted bolts, and for variations on full-column boltsn Bolt per-formances were compared using the performance of the 3/4-in full-column resin-grouted bolt as the standard. New and innovative systems can also be qualitatively compared against this standard. Since the medium into which a resin-grouted bolt is installed is one of the most important parameters affecting bolt performance, various host mediums were used in the testing: sandstone, concrete, simulated coal, simulated shale, and plaster. Bolt performances expected in other mediums can be inferred from the response patterns obtained in these mediums. Results indicate several functional differences among bolt types. Where resistance to shear is important, point-anchor bolts may outperform nontensioned full-column bolts at a lower cost. In medium-to soft-strength rock, tensioned full-column bolts perform best. Also, varying the resin-steel ratio seems to have little effect on the properties of a full-column bolt, when proper resin mixing is ensured.

Jan 1, 1985

By Thomas H. Dubaniewicz

The National Institute for Occupational Safety and Health, Pittsburgh Research Laboratory, conducted a study of past mine explosions to identify the ignition locations and ignition sources responsible for the most severe explosion events resulting in death. Since the Scotia disaster of 1976, many fatalities from underground coal mine explosions have been linked to nonpermissible electrical equipment ignition sources located in intake air courses. With few exceptions, explosion protected equipment is generally not required in intake air courses of gassy underground coal mines in the US. Cigarette lighters were another prevalent ignition source for fatal explosions ignited in intake air courses. Several mine rescue/ recovery teams have encountered electrical ignition hazards. The study provides evidence that intake air courses of gassy underground coal mines fit the description of certain Hazardous (classified) locations described in the US National Electrical Code®. Class I Division 2 or Zone 2 explosion protection tech¬niques may be used to design intake air equipment so that it does not present an ignition source under normal operation, before mine power is shut down in emergency situations. Nonpermissible circuits in intake air courses that are likely to remain energized during emergencies, e.g. battery powered equipment, should be protected by more stringent Class I Division 1, Zone 1, or Zone 0 techniques, to protect rescue/recovery personnel.

Jan 1, 2009

By Arnold F. Stalder

The measurement of various gas concentrations in the atmosphere at a particular location has become a problem of considerable importance. Levels that need to be monitored vary from the range of percent for constituents such as oxygen to parts per million levels for gases like nitrogen dioxide. In particular, mine air can become contaminated with noxious or toxic gases from several sources: fires within the mine, diesel-powered equipment, and explosive sources. The contaminants that result are carbon monoxide (CO), carbon dioxide (CO2), and oxides of nitrogen (NO and NO2). Additionally, oxygen (O2) may be depleted. Thus, the workman can be exposed to potentially toxic or asphyxiating atmospheres. A device was needed that will continuously monitor the mine air in working areas and provide warning of hazardous atmospheres. The Mine Air Monitor was conceived as being a portable, rugged instrument capable of measuring the concentration of the various atmospheric constituents in the mine environment. The unit was to provide both warning signals and quantitative measurements when hazardous contaminants existed at too high a level, or when the oxygen was being depleted. The initial concept involved optical sensors for all of the contaminating gases to be measured, namely CO, CO2, CH4, and NO2, and an electrochemical cell to monitor O2. When the explosion proof requirements of Schedule 2-G made the concept appear to be unfeasible from the standpoint of weight and portability, the program was redirected and a three channel monitor employing electrochemical sensors was adopted. In this case the gases to be monitored were O2, CO and NO2. The remainder of the program was oriented towards obtaining good, commercially available lectrochemical sensors for the above gases, testing them, reducing deficiencies noted during these tests, and making the necessary modifications to integrate the three sensors into a Mine Air Monitor suitable for the mine environment.

Jan 1, 1974

By Todd M. Ruff

Current methods of inspecting wire rope for broken wires or excessive wear include visual inspection, physical measurements of rope diameter, and electromagnetic nondestructive testing (NDT). Visual inspection and physical measurement arc the least comprehensive methods. Electromagnetic NDT enables a more thorough assessment of the condition of a wire rope, but the repeatability, accuracy, and objectivity of this method can be improved. One means of achieving this goal is to use a computer to analyze the test data and determine the condition of the wire rope, including the presence of broken wires and corrosion, and the amount of wear. An off-the-shelf data acquisition and analysis system was tested in a U.S. Bureau of Mines laboratory using a continuous loop of wire rope containing fabricated flaws. The test rope was run through a commercially available NDT instrument. The output of the instrument, normally connected to a paper strip chart recorder, was digitized and analyzed with a personal computer. These initial tests were successful in showing that the use of a computer can improve current methods of NDT waveform collection and analysis.

Jan 1, 2010

By D. Harrington

More or less unconsciously and from sheer force of habit human beings do many things they probably would not do if the possible consequences of their acts were fully recognized and appreciated. Such carelessness ordinarily could be condoned if human life were not at stake, but it is difficult to understand why intelligent men engaged in the hazardous occupation of mining indulge with the utmost indifference in some habit or continue some custom in violation of State leas and company regulations and under circumstances that may jeopardize not only their own lives but those of scores, even of hundreds, of their fellow workers as well. The old adage that stolen sweets are the best may or nay not have some foundation, but when applied to the practice of smoking surreptitiously in a coal mine, more especially a gassy mine, it is without even remote justification. Although a relatively harmless habit in the proper environment, smoking has been the cause or suspected cause of many gas explosions and black-powder ignitions and has resulted in numerous instances of bodily injury, loss of life, and destruction of property. Likewise, many fires in both coal and metal nines, causing loss of life, have been started by smoking.

Jan 1, 1941

By F. S. Crawford

Companies which have been engaged in safety work for a number of years are becoming increasingly aware of the fact that it is not enough to supply guards for various pieces of machinery and equipment and to supply safety inspection to see that rules are being carried out. Studies of many safety organizations have demonstrated that the accidents which could have been prevented by proper guards constitute only a small percentage of the total acci- dents, and amount to perhaps not more than 15 per cent. Evidently, if success is to be attained in preventing all accidents which it is humanly possible to prevent, a company must have the cooperation of every employee. Mining particularly presents probably the greatest hazards of any industry. Prevention of accidents. is made increasingly difficult because men often work alone, although generally in pairs, and only in the concentrated systems of mining do they usually work in groups of more than three or four. Supervision is difficult, therefore, and much reliance must be placed upon the individual workmen. In mining, as perhaps in no other occupation, it is of the greatest importance that individual workmen should receive continuous safety education. Within the last few years safety education has come to the front as one of the most important of accident-prevention measures, although it is true that its importance has been repeatedly stressed by the United States Bureau of Mines and other national safety organizations since the inception of the safety movement many years ago. A review of the safety educational methods of some companies in the Lake Superior district should be of interest. Perhaps better methods are in use in other parts of the country, but the methods shown have been instrumental in many cases in reducing the number of accidents. In one mine in the district whose methods are described the frequency of accidents has been reduced to zero within the last two years. A number of other mines in the district have recently gone into the class having no lost-time accidents for considerable periods of time. One company in the Lake Superior region, operating over 30 mines, succeeded during one month of 1930 in operating every mine without having a single accident which caused lost time beyond the day of the injury. Records like these are increasing in number, and while it is believed that they are the combined result of different means of safety activity, it is undoubtedly true that many of these results were obtained through safety educational methods.

Sep 1, 1931