Search Documents

By W. M. Weigel

"Sand is one of the commonest materials for industrial use, not only as a building material, but in many industrial processes. The general name applies to all grades, from the comparatively impure, unsorted product used in concrete, to especially sized products of extreme chemical purity. Various definitions have been proposed, all more or less open to objection, as they fail to cover special applications. One is: ""Sand - The fine granular material naturally or artificially produced by the disintegration or crushing of rock or slag"". This does not fit the definition of sand as understood by geologists, who consider sand only as a naturally formed product. Another is: ""Sand - The fine granular material naturally produced by the disintegration of rock"". This does not take the chemical com-position into account, and for practically all uses, except in concrete and plaster products, a material composed predominantly of silica or rather quarts is implied.Sand for special purposes usually requires different methods of preparation from those where the ordinary mixture of sizes as naturally occurring are suitable. One of the classes requiring the most uniformly sized grains is sand blast sand.Sand Blast SandThe use of the sand blast has increased rapidly during the past few years. It was formerly used almost entirely in the foundry to clean and remove inequalities from rough castings. This is still the most important application, but in addition, it is now employed for the removal of paint from old surfaces, carving and engraving on stone and marble, glass cutting, cleaning or renovating the rails of stone and brick buildings that have become discolored, preparing the surface of metals for the electrolytic bath, putting the final finish to metal surfaces, and has even been proposed as a means of channeling or cutting out blocks of stone in the quarry."

Jun 1, 1924

By C. J. Thompson

This Bureau of Mines study describes the preparation of sulfur compound concentrates boiling from 225° to 400° C, and reports the sulfur types detected in these concentrates by low-voltage mass spectrometry (LVMS). Existing LVMS methods were extended; the procedures described should be generally applicable to high-boiling petroleum distillates and concentrates as a preliminary means of narrowing the number of factions to be considered for more detailed separation and identification studies. The following major sulfur compound constituents of petroleum are indicated by the data: benzothiophenes, dibenzothiophenes, naphthanothiophenes, naphthenobenzothiophenes, and homologs and isomers of these. Cyclic and chain sulfides comprise a significant portion of the gas-oil range sulfur compound types. The presence of some classes of sulfur compounds containing two sulfur atoms per molecule was indicated.

Jan 1, 1966

By Hillary W. Clair

An equation is derived for the rate of reaction of a sphere of metal oxide in a restricted enclosure through which a reducing gas is flowing . The equation takes into consideration the reaction rate coefficient , transport through the gas and through the porous shell of reduced oxide , the rate of gas flow , and the volume of the enclosure . The equation serves as a model for predicting the course of reduction of a particle of metal oxide in a shaft furnace .

Jan 1, 1964

By H. C. Young

This paper deals with roof bolting in Alabama coal mines and iron-ore mines from the time it was introduced in early May 1948 to May 1, 1953, a 5-year period. The Tennessee Coal & Iron Division of the United States Steel Corp. began systematic roof bolting in early May 1948 in a coal mine and in an iron-ore mine, which had some of the poorest roof conditions in the Alabama mines. After the efficiency of roof bolting had been proved by the Tennessee Co. it was gradually adopted by other companies throughout the State, until in May 1953 approximately 53 percent of Alabama's total coal production and 100 percent of Alabama's total iron-ore production, mined underground, was being produced from roof-bolted areas. Statistics in this report will show the advancement made in roof bolting in the 5 years and also the amount of roof bolting that was being done as of May 1, 1953. Significant progress has been made in the coal and iron-ore mines of Alabama in reducing the roof-fall fatality rates during the past several years by adopting systematic roof bolting. The groundwork was laid through successful experiments early in 1948 by the Tennessee Coal & Iron Division of the United States Steel Corp. in cooperation with the Federal Bureau of Mines. This experimental work was based upon the previous experience of the St. Joseph Lead Co.2/ in its Southeastern Missouri mines.

Jan 1, 1954

By P. C. Good

Tungsten metal in fused form and of high purity was prepared by reducing tungstic oxide with redistilled calcium metal in a heavy-walled sealed reactor. Alloys of tungsten with vanadium, molybdenum) chromium, columbium, and tantalum were prepared by coreduction of mixed metal oxides in the same manner. This work was undertaken by the Bureau of Mines to investigate new approaches for preparing tungsten and its alloys in high-purity form. The standard method of producing tungsten metal has been the reduction of tungstic oxides by hydrogen. The resulting metal powder is compacted, sintered, and fabricated by powder metallurgy methods. Long experience in this field has resulted in the development of a technology that (by careful control of the variables such as metal composition, particle size, and sinterng technique) is well adapted to producing wire and the small shapes usually prepared from tungsten metal.

Jan 1, 1961

By Keith G. Wallace

Coal mine ventilation systems are often subject to high leakage rates. As a result, changes in airflow resistance will strongly affect the efficiency with which air is delivered to the working place. One major source of airflow resistance is the line brattice used to direct air from the last open crosscut to the working face. Because it is a great distance from the fan, the resistance of the line brattice can result in more overall leakage than an equivalent resistance closer to the fan. Substituting auxiliary fans for brattice eliminates this source of resistance, with improvements in system efficiency and cost. Also, in some mines, the leakage that leads to spontaneous combustion can be reduced. The benefits obtained by several different brattice and fan substitutions have been studied by Mine Ventilation Services, Inc., Lafayette, CA, under contract to the U.S. Bureau of Mines. Changes in main fan duty were compared with additional costs associated with auxiliary fans. Results indicate that in some circumstances, considerable leakage reductions and cost savings are possible.

Jan 1, 1990

By L. C. George, J. W. Jensen

A new system for precisely counterbalancing and measuring vapor pressure operates by servomechanical principles . It was developed with the objective of determining the vapor - pressure equations of metal halides . The system is isolated from the vapor - pressure bulb by a diaphragm transducer that signals a pressure regulator to null any pressure difference that is detected . Pressure measurement and readout are continuously performed by a servomanometer , accurate to ±0.003 cm Hg for the range of 0.1 to 200 cm Hg . High response rate and sensitivity are obtained . Methods of use are described , and results for CdC1 and PbC1 , in agreement with data of other investigators , are given as examples .

Jan 1, 1964

By Robert M. Doerr

The oxidation kinetics of Ni-Y alloys in the range 0.04 to 8 weight-percent Y, and of high-purity Ni, were compared by the use of a sensitive volumetric apparatus. The reactions followed approximately the parabolic rate law; for oxidations in 02 at 0.5 atm and 1,200° C, the parabolic rate constant was about 0.37 + (0.064) (Y-2.11) mg cm-2 min-1/2, where Y represents the weight-percent Y in the alloy. Internal oxidation of Y occurred in the alloy specimens and the resultant Y203 particles, which were in patterns related to the eutectic structure of the alloys, served as markers showing that the subsequent oxidation of the surrounding Ni was by inward diffusion of O. The scale consisted in each case of NiO, but the inner parts of the scale on the alloy specimens included the patterned Y203 particles. The thicknesses of the inner parts of the scale depended directly on the Y concentration, and the thicknesses of the Y2O3-free outer parts of the scale were inversely related to the Y content of the alloys. There is thus a relationship between the thickness of the outer part of the scale and the protectivity of the scale. Outward diffusion of Ni and inward movement of 0, from the inner boundary of the Y2O3-free part of the scale, is proposed as a mechanism for these results.

Jan 1, 1966

By G. W. Jones, F. E. Scott

"INTRODUCTION As a part of its program of promoting safety in mining and other industries, the Bureau of Mines investigates the explosion hazards of combustible Gases, vapors, and solids. It also investigates various means and methods of controlling and mitigating explosions.Dichlorodifluoromethane, CC12F2, has been found to be very efficient as a quenching agent for methane flames. 4/ This substance is a gas at ordinary temperatures and pressures and is relatively nontoxic and stable at mod rate temperatures.Tremendous quantities of dichlorodifluoromethane were used daring the late war as an expelling agent for aerosol mixtures in ""aerosol bombs."" At one time during the war the demand for Dichlorodifluoromethane became so gent that there was barely enough of it to supply the Army and Navy and virtually none for civilian needs. During this period of scarcity the Bureau of Mines, in cooperation with the Bureau of Entomology, Department of Agriculture, investigated the possibility of substituting other materials in part for the dichlorodifluoromethane. It was required that the resulting mixtures be satisfactory expellant and noninflammable under all normal conditions of use."

Jun 1, 1946

By G. G. Campbell

Bureau of Mines research to develop an in situ retorting recovery method for oil shale has involved field testing of fracturing techniques for creating fluid-flow paths in impermeable oil shale. Electrolinking, hydraulic fracturing without and with sand propping, and explosive fracturing with a liquid explosive were tested in a 25-ft-square, five-spot pattern. These wells were drilled into oil shale at 50-to 88-ft depths near Rock Springs, Wyo. Results of the fracturing tests were evaluated by injecting air into a test well and measuring flow rates and flow profiles in adjacent test wells before and after each test. To identify points of air entry (location of fractures) in wells, flow profiles were determined by use of inflatable packers and by continuous logging with an airflow probe developed during the fracturing program. Electrolinking and hydraulic fracturing without sand propping were relatively ineffective; hydraulic fracturing with sand propping created horizontal fractures with desirable flow capacity; and fracture flow capacity was significantly increased by detonation of nitro-glycerin displaced in the natural and hydraulically induced fracture systems.

Jan 1, 1970

By F. N. Kissell, C. D. Litton

This study ranks the factors impacting survival during a coal mine fire. It bas already been established that reducing time delays is the most important factor in saving lives. Consequently every event during afire is measured in terms d its duration, and the effectiveness d any action taken to improve survival is measured in terms d the time it saves. By ranking actions according to time saved these authors found that a comhination d actions was most effective. This combination was: • installing lifelines. • moderately decreasing air leakage and • decreasing the fire growth rate. Changing ventilation leakage alone was much less effective, as was altering the CO (carbon monoxide), sensor alarm threshold. These results confirm an earlier fault-tree study on escape from mine fires. The fault-tree study bad shown that, with the exception d delays, single factor changes have minimal impact. Significant reductions in fire fatalities only take place with multiple factor changes.

By H. G. Iverson

As a part of the program of investigation of domestic sources of manganese ore, mining engineers of the Bureau of Mines examined and sampled three properties in the vicinity of Winnemucca, Nev. As the ores were too low grade for direct production of ferromanganese, they were tested for their amenability to concentration by ore-dressing methods. Two samples of ore were procured by examining engineers of the Bureau of Mines from several outcrops in the Pollard Canyon area, Pershing County, about 30 miles southeast of Winnemucca. The manganese occurs in relatively small lenticular bodies as secondary replacement deposits in chert and quartzite. The first sample represented average run -of -mine ore as exposed in the Pollard Canyon deposits. Sample 2 was composed of hand-sorted, high-grade ore.

Jan 1, 1954

By L. G. Marshall

This report is one of a series published by the Federal Bureau of Mines describing mining methods and performance at individual operations throughout the United States. The objective of these papers is to promote development and conservation of our mineral resources by disseminating reliable technological information on mining methods, practices, and results that may be applied to the engineering analysis and solution of mining problems. SUMMARY Operation of a limestone quarry producing flux for the steel industry and crushed stone for production of concrete is described in this report. The deposit being mined is a flat-lying limestone formation under a thin overburden 2 to 25 feet thick. The height of the quarry face varies from 9 to 60 feet, averaging 40 feet. Production rate ranges from 4.5 to 5 million long tons per year.

Jan 1, 1959

By Ivette E. Torres

For a study such as this, which summarizes and amalgamates much information collected, compiled, and utilized by the numerous U.S. Bureau of Mines country specialists and branch chiefs for inclusion in their country and regional reports that comprise the five other sections of 1992 Minerals Yearbook-International Review, it is clearly impossible to cite all sources of information used in its presentation, but some recognition is due. Generally speaking, this study and its related detailed studies on countries and areas would be much more difficult, if not impossible to complete, without the efforts of the personnel of our counterpart national mining and geological agencies throughout the world. Information that they collect, compile, and then publish, either in their own volumes or those of central statistical agencies in their countries, are the foundations on which this work rests. Thus, our appreciation is expressed to the multitude of persons employed by these agencies for their contributions.

Jan 1, 1994

By Raja V. Rarnani, Robert L. Frantz

"Scientific, engineering, and biomedical research teams synergystically developed major topical research areas in the Respirable Dust Center. Descriptions of their interactions and resulting accomplishments demonstrate how cooperative research within and among these study groups benefits the overall respirable dust research and practical application needs of the mineral industries.The development of a state-of-the-art small animal inhalation exposure facility suitable for studies of fresh and aged coal mine dust, a major goal of this research group, will contribute toward the GTCRD goal of advancing the understanding of causative mechanisms for the occupation-related lung impairments and the airway diseases of mine and mill workers. Such understanding includes improved definition of the role of various aspects of the lung environment (e.g., surfactant and the mucociliary system) in the disposition and toxicity of respirable dust, comprehensive characterization of the role of the pulmonary alveolar macrophage (PAM) and its secretory products on the development of dust-related lung disorders, and an expanded search for methods to reduce the toxicity of respirable dust both before and after it enters the lung. The National Academy of Sciences has recommended, in Measurement and Control of Respirable Dust in Mines, that respirable dust research should include study of the behavioral and constitutional factors affecting individual susceptibility to workers' pneumoconiosis occupational disease and the development of methods for detecting the potential onset of pneumoconiosis earlier and more conclusively than can be done using X-ray methods. These recommendations have guided the research group in its goals of establishing and disseminating a scientific protocol for standardizing the inhalation testing for all research objectives within the Generic Center which involve small animal exposures and implementing the infrastructure necessary to make lung tissues obtained during inhalation studies available to all researchers within the Generic Center."

Jan 1, 1995

By C. E. Wethered

This paper describing the mining methods employed by the Federal Mining and Smelting Co., operating the Morning mine at Mullan, Idaho, is one of a series being prepared by the United States Bureau of Mines on mining practices, methods, and costs in the various mining districts of the United States. The daily tonnage produced at the Morning mine, including that mined by leasers, is 1,100 tons. Mine run of ore will average 9.1 per cent lead, 5.8 per cent zinc, and 4.4 ounces silver per ton. A stull set and fill method of mining is employed.

Jan 1, 1930

By Frank K. McIntosh

The Wood mine area was investigated by the Bureau of Mines in -1941 by a magnetic survey and a gravitational survey. Surface trenches were excavated, and diamond-drill holes were bored at the strongest anomalies developed in common by the two surveys. In the last century', several widely separated bodies of chromite with some magnetite had been exploited in a 'serpentine belt near its contact with schist. At one time this district held a virtual monopoly on the production of chromite. Known ore bodies now are exhausted. Owing to the relatively high specific gravity of chromate compared to normal rocks, a gravitational survey was run to determine which magnetic anomalies were worthy of diamond drilling. Linear feet of trenching totaled 1,710 feet. Ten holes were diamond drilled, which totaled 2,272 feet. The log of the drilling is shown in the text in a tabulation of drill-hole data.

Jan 1, 1948

By W. L. O'Brien, E. A. Rowe

Electrorefined vanadium with additions of up to 5 percent by weight of yttrium, cerium , lanthanum , praseodymium, neodymium, and samarium was melted to ingots in a nonconsumable electrode arc in a helium atmosphere . The ingots were rolled into strips and evaluated for the effect of the alloying elements on hardness , tensile strength , ductility , recrystallization temperature , and microstructure . Except for samarium , average additions of alloying elements of 1 to 2 weight - percent resulted in the retention of 0.12 to 1.05 weight - percent in the alloys and reduced the ultimate tensile strength from about 48,000 to approximately 30,600 psi . The corresponding yield stress (0.2 percent offset ) was reduced from about 40,700 to approximately 20 , 200 psi . Diamond pyramid hardness (DPH) was reduced from 117 to an average of 62 kg /mm² . Increased malleability at room temperature resulted with yttrium and all rare - earth- metal additions , except samarium , particularly with more than 0.25 weight - percent additions . Decreasing oxygen contents corresponded with the changes noted in the mechanical properties of the alloys . The recrystallization temperature of electrorefined vanadium was reduced from approximately 950 ° to 800 ° C. Yttrium or a rare- earth metal content , except samarium , in excess of 0.1 weight - percent in vanadium produced a second phase suggestive of an eutectic which indicated a possible maximum solubility of less than 0.1 weight - percent for both room and elevated temperatures .

Jan 1, 1964

By Robert M. Cox

The U. S. Bureau of Mines (USBM) MULSIM/NL modeling technique has been used to analyze anticipated stress distributions for a proposed alternative longwall gate road design for a western Colorado coal mine. The model analyses indicated that the alternative gate road design would reduce stresses in the tailgate entry without increasing stresses in the headgate entry. To test the validity of the alternative gate road design under actual mining conditions, a test section of the alternative system was incorporated into a subsequent set of gate roads developed at the mine. The alternative gate road test section was instrumented with borehole pressure cells, as part of an ongoing USBM research project, to monitor ground pressure changes as longwall mining progressed. During the excavation of the adjacent longwall panels, the behavior of the alternative gate road system was monitored continuously using the USBM computer-assisted Ground Control Management System. During these field tests, the alternative gate road system was first monitored and evaluated as a headgate, and later monitored and evaluated as a tailgate. The results of the field tests confirmed the validity of using the MULSIM/NL modeling technique to evaluate mine designs.

Jan 1, 2010

By F. M. Boler

The U.S. Bureau of Mines has configured a flexible data acquisition and analysis workstation, which incorporates control and analysis software written in-house for use in mining research experiments conducted in the laboratory and in operating underground mines. This data acquisition system combines computer-automated-measurement-and-control (CAMAC) modular instrumentation with a Unix-based graphics workstation. The data acquisition front-end hardware can be interfaced to almost any computer. CAMAC instrumentation modules adhere to mechanical, electrical, and digital interface standards and can be custom designed or purchased off the shelf. Communications along the CAMAC bus are regulated by the crate-controller module, which contains the only hardware link to the computer interface. Software support for the data acquisition and analysis workstation consists of a series of functions and programs written in the "C" programming language designed to provide flexible and fast data acquisition, processing, and analysis. The user can interactively control the digitizers and other CAMAC modules by sending standard CAMAC read, write, and command function codes from a menu-driven program. Automated data collection is achieved through software that responds to hardware interrupts triggered by acoustic emission or microseismic events. Graphics display routines are used to plot part or all of the data and provide the ability to process and store signal information selectively.

Jan 1, 1990