Search Documents

By E. G. King

THIRD-LAW entropy data for zirconium-containing compounds are sparse. Kelley a lists entropies at 298° K. for the oxide, tetrachloride, nitride, and silicate, as well as for the metal. The present paper presents heat capacities between 51° and 298° K. and entropies at 298.15° K. for the zirconates of the alkaline-earth metals-calcium, strontium, and barium. The authors believe magnesium zirconate does not exist as a stable compound at room temperature. Entropies of formation from the constituent oxides also are given. MATERIALS The materials used in this investigation were synthesized and analyzed in the Berkeley Laboratory of the Bureau of Mines. Calcium zirconate was prepared by heating an intimate mixture of reagent-grade calcium carbonate and pure zirconia for 30 hours between 1,200° and 1,300° C. and for 32 hours between 1,400° and 1,500° C. As part of the heating schedule, the sample was ground and mixed seven times. Periodic analyses and minor adjustments of composition were made. Analysis of the final product gave 31.19 percent calcium oxide (theoretically 31.28 percent) and 68.67 percent zirconia (theoretically 68.72 percent). The X-ray diffraction pattern agreed with that in the ASTM catalog.

Jan 1, 1960

By Robert E. Barieau

General expressions for evaluating practically all the thermodynamic properties of a fluid from a single equation of state are derived. Most of the formulas are expressed in terms of the compressibility factor, with this factor being an explicit function of the temperature and the molal density. Similar expressions are given using reduced variables.

Jan 1, 1967

By Wallace W. Roepke, Jon I. Voltz

"The Bureau of Mines determined coal-cutting forces and primary dust generation of four styles of radial gage bits as used on end rings of continuous mining machines. Direct comparisons for reference were made with two widely used conical plumb-bob types having 60° and 90° (nominal) included tip angles. The cutting forces for all of the gage bits were similar to those of the 60°-tip plumb-bob bit. All bits except the RAD-3 gage bit generated similar amounts of primary total dust at shallow cutting, but during deeper cutting, the amounts varied and the gage bits produced as much as 2-1/2 times the dust produced by the 60° bit. This seems atypical since past experience has always shown differences in dust generation at shallow cutting. The specific energy was more like that found previously with other bits, since the values were spread at shallow cutting but became nearly similar at deeper cuts. The 90° bit and the RAD-3 gage bit are not recommended for use except in extremely difficult cutting conditions where dust and forces are of secondary importance. The choice among the remaining four bits can be made on the basis of dust, energy, forces, or cost, as circumstances dictate. INTRODUCTIONThe Federal Coal Mine Health and Safety Act of 1969, with revisions in 1977, was enacted to ensure more healthful and safer working conditions for miners. The Bureau of Mines coal-cutting research facility at Twin Cities (MN) is examining fundamental aspects of the cutting system, including generation of primary dust causing pneumoconiosis in miners and ignition of methane by the frictional impact of cutting bits used on continuous mining machines (CMM's). The cutting system is defined as the cutter-mineral interface area with all its variables, e.g., forces, speed, cutter geometry, bit-mounting geometry, and wear. It has become obvious over the past several years that the cutting system directly affects the economics and design of the ""total system,"" which is defined as all areas of the operation, from the mine face to the preparation plant, which support the mineral recovery by cutting tools to obtain a salable product."

Jan 1, 1983

By THOMAS SOULE, R. I. C. Manning

The Phelps Dodge Corporation considers safety a major operating problem , both from the humanitarian standpoint , for this company has a real interest in the welfare of its employees , and from the economic standpoint , for it has found the safe way to be the most economical . In turn , a feeling among employees that the company really has their interests at heart has a wonderful psychological effect . It is bound to bring forth more and better work and to attract and keep workmen of the better class . There is keen competition between the various branches of this corporation for a trophy that is awarded each year to the one having the best accident record . This trophy was won by the Nacożari branch of the Moctezuma Copper Co. in Mexico in 1926 and 1927 , and the Morenci branch won the trophy in 1928 and 1929 .

Oct 1, 1930

By W. P. Yant

The hazard to health from contamination of air by a noxious gas depends not only on the potential harmful response attending exposure, but also on the warning properties, which in effect may be termed the "accompanying warning response," This warning may be manifested as an odor, taste, irritation of the eyes, nose, or throat, or perhaps headache, vertigo, or nausea. These manifestations may be painful and even slightly harmful, but to a much lesser degree than the primary injury of exposure. The warning response mitigates hazards directly in proportion to the degree of Intolerability which accompanies injurious exposure, and accordingly its absence augments hazards. This accounts for the fact that the actual health hazards from a non-odorous or non-irritating gas or vapor of comparatively low toxicity sometimes equal or exceed the hazard from a considerably more toxic substance, but one which possesses a marked odor or produces eye, nose, or throat irritation in advance of harmful exposure. When a substance lacks the properties for giving warning, it is often possible to impart them by the addition of a small amount of another substance which has an exceedingly high warning intensity. The vapors of this substance, commonly termed a "warning agent" or "tracer gas," escape and mingle with the gas or vapor which lacks warning properties and thereby apprises persons of the latter's presence. The amount of the warning agent added is that which will give adequate warning in advance of serious physiological harm from the dangerous gas or vapor.

Jan 1, 1930

By D. J. Parker

This report is based on data collected in and about the Liberty mine of the Liberty Fuel Co. by D. J. Parker and W. W. Kessler on December 13 and 14, 1933. An important phase of an examination to determine the general condition of a mine with respect to safety is the collection of dust samples from rock- dusted areas. Definite conclusions, based on intelligent interpretation of the analyses of such samples, can be reached only when the general condition of the mine is known. A similar examination and report were made on this property in January 1930 by D. J. Parker and R. I. C. Manning. Since that time much has been done by the management to improve safety conditions in this mine. The changes made will be noted in the course of this report. The mine is in Spring Canyon at Latuda, Carbon County, Utah, and is served by a branch line of the Denver & Rio Grande Western Railroad about 7 miles long and connecting to the main line near Helper, Utah. The writer desires to express his sincere appreciation for the many courtesies and helpful cooperation extended by Superintendent George Schultz and Mine Foreman F. W. Koelling.

Nov 1, 1934

By R. M. Gammell, S. H. Lorain

The Anderson prospect is one of a number of properties investigated by the Bureau of Mines during the course of preliminary studies of the lead-zinc districts of northern Stevens County, Washington. examined by W. R. Green, an engineer of the Bureau of Mines, in June 1944. This examination was supplemented in late 1944 and the spring of 1945 by pre- The property was first liminary angle-dozer trenching and core-drilling. A second examination of the property was made by the junior author in November 1945. The data obtained in the course of these studies is presented in the following report.

Mar 1, 1947

By E. G. King

The work described in this Bureau of Mines report was undertaken to fill a need of industry for high-temperature heat-content data for uranium tetrafluoride. Without such data, heat balance evaluations of processes involving this substance are seriously hampered. Measurements of the heat content of uranium tetrafluoride were conducted at temperatures from 298° to 1,350° K. The melting point and heat of fusion were determined. The results are presented in suitable tabular form, and representative heat-content equations are included.

Jan 1, 1961

By Steven J. Page, John A. Organiscak, Thomas Mal

Monitoring the miner respirable quartz dust exposure for compliance with U.S. federal regulations is mandatory to protect the health of coal miners. However, there is no technique available for the direct measurement of the respirable quartz dust concentration in the mining environment. The only means to estimate the respirable quartz dust concentration is to perform an analysis of the respirable dust sample collected, which contains both coal and quartz dust as well as other mineral constituents. For samples collected at coal mines, the U.S. Mine Safety and Health Administration (MSHA) utilizes the P7 method for respirable quartz analysis. The objectives of this work are to 1) evaluate the performance of the P7 method on field samples of low quartz mass loadings, 2) evaluate the magnitude of dust mass spatial variability within an enclosed cab environment, and 3) estimate the subsequent propagation of error in calculating the per. centage of quartz over a broad range of mass and quartz filter loadings at a surface coal mine. These objectives were achieved by obtaining surface coal mine dust samples over a 9-month time period in enclosed cabs of three drills and three bulldozers. By measuring weighing precision and using reasonable estimates for sampler variability, the dust mass spatial variability component was calculated by difference. The results show that 1) the P7 method can be precise and linear with quartz mass loadings as low as approximately 5 µmg of quartz, 2) the dust mass spatial variability, even within an enclosed cab environment, is the dominant factor of variability in propagation of error in estimating the quartz content of the obtained dust samples on a percentage basis, and 3) weighing precision is not a significant factor in error propagation. In addition to the enclosed cab samples, samples from eight surface coal mine drills were collected at various locations exterior to the drill cab. Significant data scatter at these outside locations strongly suggests that the ambient dust mass spatial variability has a significant effect on the propagation of error in estimating quartz content of the dust samples on a percentage basis.

By Forrest T. Moyer, J. I. DAVIS, JOSEPH H. SCHUSTER, E. K. ELSNER

The National Safety Competition conducted by the Bureau of Mines, United States Department of the Interior, is held each year for the purpose of promoting safety in the mineral industries of the United States. Since the program was inaugurated in 1925, twenty-three safety competitions have been held. This publication is a report of the results of the contests held in 1944, 1945, 1946, and 1947. The names of plants that have been awarded "Sentinels of Safety" trophies and Certificates of Achievement in Safety dur- ing these years, together with a summary of their achievements in injury prevention, are listed. Statistical data covering the injury experience of all plants entered in the annual contests also are included in this publi- cation. The injury statistics of these plants, arranged in the six groups of the competition, are the only data on injury severity at mineral operations available to the Bureau of Mines. Interest in the National Safety Competition has increased steadily. The number of participating plants has increased from 210 in 1925, the first year of the competition, to the record number of 494 in 1946. The widening scope of the competition means that a steadily increasing number of the mines and quarries in the United States are participating in a program that will supplement their other activities in promoting safety. Safety competitions have long been recognized as instrumental in stimulating and holding the interest of employees and officials in accident-prevention work. During the years covered by this report, conditions in the mineral industries of the United States were hardly conducive to setting records in accident prevention. During the war years, handicaps were especially severe- loss of skilled employees to the armed forces or to higher-wage war industries, greater production by a smaller force of workers, relatively high rates of labor turn-over, the longer workday in effect through 1944 and 1945, and difficulties in obtaining repairs and replacement for badly worn machinery. Even the immediate postwar period has brought no abatement of the tremendous pressure upon the mineral industries for greater production. Although there was a decrease of 18 in 1947 from the record enrollment in 1946, these oper- ations worked 160,525,025 man-hours, the greatest number of man-hours of exposure to mining hazards in any year of the contest except 1942. Despite the accelerated pace at which the mineral industry worked during the 4 years covered by this report, participants in the National Safety Competition have achieved creditable performances in the promotion of safety. In fact, the injury-severity rate in the enrolled plants in the 1947 contest was 7.315 days for each thousand man-hours worked, the lowest by far in the history of the National Safety Competition. The injury-frequency rate of 42.155 for each million man-hours of exposure to mine hazards in 1947 marks a favorable trend downward from the rate of 50.577 in 1946, which was the

Dec 1, 1949

By J. B. Newson

This is one of a series of circulars dealing with mining methods, practices, and costs. It describes the method of sinking a shaft 60 inches in diameter with a shot drill, as employed at the Idaho Maryland mine, Grass Valley, Calif. The operation involved a great deal of experimentation in applying the shot-drill method to large bore drilling, overcoming mechanical and other difficulties which developed during sinking, and developing operating technique. Under such circumstances, costs are obviously higher than they would be after the pioneer work has been done, but even so, these actually obtained compare favorably with costs of sinking by more conventional methods. ACKNOWLEDGMENTS The authors are indebted to Mr. Errol McBoyle, president of the Idaho Maryland Mining Co., not only for his cooperation and advice during the sinking of this experimental shaft, but for permission to prepare this article for publication with the inclusion of cost data.

Jan 1, 1936

By C. W. Smith

Research was conducted to evaluate the effectiveness of a well-point dewatering system in conjunction with a french drain to intercept waste impoundment leakage while reducing the volume of waste water requiring treatment. A well-point dewatering system composed of 585 production wells was installed around the perimeter of a leaking impoundment that previously used only a french-drain system for leakage control. The placement of the well-point system was designed to intercept and remove the leakage from the groundwater before the contaminant reached the french drain. Groundwater monitoring at this site revealed that after a period of approximately 40 days the well-point dewatering system had stabilized and effectively prevented the further spread of contamination to the french drain.

Jan 1, 2010

By Oliver Bowles

Granites are classed as igneous rocks ; they have been formed by the solidification of rock magmas or solutions from deep within the earth . It is an almost invariable law of nature that magmas which cool quickly form fine- grained or glassy rocks , while those that cool slowly are completely crystallized and are coarser- grained . Granites , being of the latter class , are regarded as having attained their solid form at considerable depth below the surface under conditions of high temperature and pressure . The constituent minerals crystallized out slowly , the crystals interlocking with one another . The great depth of overlying rocks that must have been present when crystallization took place has been removed by erosion over large areas on the surface of the earth , in consequence of which granites appear at or near the surface in many localities . The chief minerals of which granites are formed are feldspars , quartz , and either mica or hornblende . All the essential constituents except mica are as hard as , or harder than steel , therefore granites are difficult rocks to cut and dress . Granites are usually red , pink , or gray , depending on the color of the feldspars . If hornblende or black mica is abundant the rock may be dark green or almost black . Granites are characterized by massive homogeneous texture . They are classified as fine- grained , medium- grained , or coarse - grained . Medium- grained granites are those in which the feldspar crystals average about one- fourth inch in diameter . If relatively coarsegrained crystals appear in a fine -grained ground mass the rock is designated a porphyritic granite . Uniformity in texture and grain size are desirable in building and ornamental stone , although occasionally rocks of variable texture , such as the porphyritic granites , are used . A rock may have the mineral constituents of a granite but show a banded or platy structure due to recrystallization , folding , or other changes while the rock was in a plastic or semimolten condition . Such metamorphic rocks are called granite gneisses . They are used occasionally for building purposes but not as commonly as the uniformly textured granites . - Granites are named from the most abundant mineral other than quartz and feldspar that they contain , being called , for example , biotite granite or hornblende granite . - Commercially other igneous rocks granitoid in texture but more properly classified as syenites , diorites , or gabbros may be classed as granites . Thus the " black granite " of Little Falls , Minn . , is a diorite , and the " black granite " of Eastern Pennsylvania consists of diabase or gabbro . The question is sometimes raised as to the depth to which a granite occurrence may extend . In this respect granites differ notably from limestones , sandstones , or other sedimentary rocks . The sediments were originally laid down in relatively thin beds , and individual formations providing rock of economic value may be quite limited in thickness . Usually the usable beds range between 40 and 200 feet in thickness . On the other hand , granite comes up from below . Its depth is unknown , but in general is very great . It may even be measurable in miles . The reserves of material at depth are to be measured , therefore , by the economic depth of working rather than by the vertical extent of the rock mass . Exceptionally , granites of commercial quality may occur in sills or sheets of limited thickness flanked on either side by rocks of different character , as , for example , at Westerly , R. I.

May 1, 1930

By James A. Powell

The theory of electromagnetic fields indicates such fields could be used to detect and locate trapped miners. To be useful, the hardware of the system must meet a number of requirements, including small size, intrinsic safety, and rugged construction. Such hardware has been built, and the system has been tested by the Bureau of Mines and its contractors. These tests indicate that the electromagnetic method provides a practical means to locate miners in emergencies.

Jan 1, 1976

Develop computer software that can aid in improving the visibility and illumination in underground mines by providing quick analysis of existing equipment and conditions and the effects of potential modifications. Background Poor visibility and illumination are common problems in underground mining. Mining equipment often restricts operators' fields of vision. Also, fighting systems are often positioned where they cause excessive glare, which restricts the visibility around the machines even further. To help address these problems, the U.S. Bureau of Mines (USBM) has developed a PC-based software package to analyze certain human engineering aspects (ergonomics) of mining equipment design. The software is available for use by equipment manufacturers and mining companies for design work on new machines, as well as for evaluating proposed modifications to existing machines. Approach The Crewstation Analysis Programs (CAP) package includes assessments of visibility, illumination, and glare in the surrounding work area. The advantage of using computers for these types of analyses is that numerous design iterations can be tested quickly and efficiently to determine the effects of changes on visibility. This cuts down the need for expensive testing using physical mockups. Another advantage is that design ideas can be tested in situations where testing would not normally be possible. For instance, the effects of modifications to a lighting system or canopy design could be tested while the machine remained in service.

Jan 1, 1993

By W. P. Diamond, A. C. Smith, J. A. Organiscak, T. P. Mucho

The U.S. Bureau of Mines conducted a worldwide literature review of bleederless ventilation practices to evaluate their use as a spontaneous combustion control measure in U.S. coal mines. Factors that must be taken into account in the design and use of these systems include seal construction, the use of ventilation control devices, the use of methane-drainage systems in gassy mines, and the ground control plan. Monitoring for the detection of spontaneous combustion and the control of methane when methane-drainage techniques are employed is critical to the successful use of a bleederless ventilation system. This report describes the types of ventilation systems used throughout the world and the spontaneous combustion risks associated with these systems. Methane-drainage systems used in conjunction with bleederless ventilation systems are discussed. Ground control considerations such as pillar design, entry stability, and seal usage are reviewed. Monitoring systems for spontaneous combustion detection, methane-drainage control, and behind seals are examined. Finally, methods for evaluating the spontaneous combustion hazard of a mining operation to determine when the use of a bleederless ventilation system is warranted are reviewed.

Jan 1, 1994

This report summarizes the work performed by the Bureau of Mines on the development of analytical procedures for determining metallic and interstitial impurities in high-purity tungsten. Fourteen published methods and seven unpublished methods are briefly described. Carbon, hydrogen, nitrogen, and oxygen, in microgram to higher quantity levels, can be determined by several methods. Trace levels of 29 metallic impurity elements can be determined by optical spectrography, X-ray spectrography, and other instrumental methods.

Jan 1, 1968

By G. W. Grove

Coal-mine officials and those who are preparing to become officials should be familiar with the instruments and devices that are employed rather commonly in and around mines and should know how to use them with safety and efficiency. Among these axe instruments and devices used in determining the pressure, velocity, volume, and certain other conditions of ventilation and in detecting the more common mine gases, such as methane, carbon monoxide, and hydrogen sulphide, or a deficiency of that very important agent, oxygen. Water gages, anemometers, barometers, psychrometers, flame safety lamps, lamp-testing boxes, and methane, carbon monoxide, and hydrogen sulphide detectors are described and their use and operation discussed in this paper.

Jan 1, 1938

By Steven W. Schmauch

The Ruby Mountains study area encompasses 75,615 acres managed by the U.S. Bureau of Land Management in Madison County, MT. A mineral survey was conducted by the U.S. Bureau of Mines and U.S. Geological Survey in 1984. Bureau of Mines personnel reviewed literature and county mining records, and examined prospects or mineralized areas to determine mineral resources. Geological Survey personnel evaluated the area by geochemical sampling and geophysical surveys. There are no organized mining districts and no current claims in the study area. Significantly mineralized quartz veins, shear zones, or talc bodies apparently do not exist within the study area. A small part of the Kelly Iron Deposit is inside, but dips away from the study area; the main occurrence is estimated to have 32 million tons of subeconomic resources that average 21 percent iron.

Jan 1, 1985

By Richard A. Andre, R. Larry Grayson, Thomas Simonyi

"INTRODCICTIONThe search for the cause(s) of coal workers' Pneunoconiosis continues despite the vast amount of research that has been undertaken over the past forty to fifty years. Good correlation between the mass of dust inhaled over workers' lifetimes and the incidence of the disease has led to the development of effective environmental standards and implementation of good procedures for the control of dust generation and dispersion in the working place. Research has only begun, however, to uncover the biochemical mechanisms involved in initiating the disease.Correlation between the rank of the coal seam in which miners worked and disease incidence and severity is acknowledged worldwide, but the agents in the higher rank coal seams which cause CWP arc still not defined. The basic components of the coal seams, i.e., the elements and minerals, are generally known, but the way in which they interact with human pulmonary cells is largely still a mystery.The process of disease development is a biochemical one which depends on the characteristics of the pulmonary cells within their immediate biochemical environment and the characteristics of invading respirable coal mine dust particles, probably both chemical and physical ones. The cell-particle relationship, therefore, must be defined, and both cells and particles must be characterized according to properties which potentially are involved in the disease process.Following such characterization, specific respirable dusts from different coal seams, which appear to have different effects on coal workers, must be obtained or constructed and then used in experiments designed to determine dust toxicity or the response of animals exposed to the dusts.The results presented here focus on characterizing properties of respirable coal mine dust particles collected from operating longwalls in West Virginia and Virginia Longwall panels were selected for analysis because the respirable dust in the coal face areas is largely uncontaminated by rock dust and analysis of the dust yields results unconfounded by rock dust."

Jan 1, 1990