Search Documents

By S. H. Ash

As part of the work done at the Washington coal mines during the year 1929 , a study was made of the safety practices in and about the mines . Inasmuch as electrical blasting has made considerable headway it is interesting to note the manner in which it is done and the reasons why it was discarded at some of the mines . Blasting is done at the mines in the State by means of capped fuse , electric blasting " caps , " and in some instances by electric delay detonators . Black blasting powder with fuse is used at most of the open- light mines . The use of squibs was discontinued several years ago because the coal operators , without exception , recognized the dangers incidental to their use . Permissible explosive and dynamite are also used at some of the open- light mines . With the exception of some rock work and the driving of level work in gangways and air courses the explosive is detonated by means of capped fuse .

Apr 1, 1930

Case studies from four western states are used to illustrate the impact of the environmental compliance process on the mining industry. The case studies were not chosen as a statistically significant sample of all mining operations in the western United States but were chosen as representative of operations on both public and private lands and in locations that exhibited varying degrees of involvement by governmental units, non-governmental organizations and the general public. Basically, each case study was chosen because some aspect of their environmental compliance process helped to illustrate an interesting point in the regulatory process. The criteria used to select the case studies were: mines located in different jurisdictional areas, mines located in varying geological areas~ mines located in areas having different historical relationships with mining: and operations that are in production as well as those seeking an operating permit. The variety of such projects should provide the necessary foundation to evaluate the impacts of the environmental compliance process in each location.

Jan 1, 1994

By Marcia L. Harris

The National Institute for Occupational Safety and Health (NIOSH), as part of its continuing research program for evaluating coal dust explosion hazards, has investigated several areas in which current practices may need to be updated in order to adequately protect mines against coal dust propagated explosions. In the United States, current rock dusting requirements remained largely unchanged since 1969. US Title 30 Code of Federal Regulations Section 75.403 is based on a coal dust particle size survey performed in the 1920s and later was supplemented by full-scale testing of the rock dust ability to inert a coal dust explosion. NIOSH recently conducted a comprehensive survey of US underground coal mines to determine the range of coal particle sizes found in dust samples collected from the mine entries. Due to advancements in technology and modern coal mining techniques, the current coal dust particles in intake airways are significantly finer than those found in the mines in the 1920s. According to past full-scale dust explosion test results, the current rock dusting practices used in today?s mines to inert a coal dust explosion may not be adequate. Other closely related issues such as rock dust testing methods and sampling procedures are discussed.

Jan 1, 2009

By R. Karl Zipf, Z. T. Bieniawski

"A set of fracture profile photomicrographs is presented for fractures generated under mixed mode loading of the Pittsburgh coal. The fractal dimension is used· to characterize the irregularity of these profiles and a tentative relationship is presented between the fractal dimension and the fracture toughness. Surface roughness appears to depend solely on the stress intensity and no other dependence was observed with fracture loading mode, loading rate· or specimen orientation. Observations of crack bifurcations.in fracture profiles can indicate crack growth direction whereas direct surface observations generally cannot in materials such as rock and coal.1 INTRODUCTIONThe production of fine fragments of material as a result of some loading event occurs in many industrial processes. In crushing and grinding, the efficient production of fine fragments is the desired end result; .however, in coal cutting, the production of fine fragments may lead to high levels of respirable dust in the immediate atmosphere with the danger of human lung diseases. Two of the most important sources of fragments in the 1 to 10 micron size range during a cutting process are 1) severe crushing in a zone near the loading tool and 2) subsequent shearing along major crack surfaces that form the larger fragments during material reduction. These and other sources of fine fragments generation are discussed by Roepke (1984) and Zipf and Bieniawski (1986). The physical character of the nearly created major crack surfaces is believed to have a strong influence on the amount of fine fragment generation that occurs during subsequent shearing movement. When the major large fragments initially form, they are ""locked"" in place by the irregular character of the new fracture surface. Only after some relative motion has occurred between fragments are they actually liberated, and the net result is the formation of additional fine fragments. The fine fragmentation is not necessarily limited to the shearing of high points from the macrocrack surf ace since material remaining in the wake of the crack tip is damaged to a substantial depth below the actual crack surface."

Aug 31, 1989

By Jeanne A. Zimmer, Charles D. Taylor, Edward D. Thimons

On a continuous miner coal face methane concentrations are affected by the quantity of fresh intake air reaching the face. When mining the box cut on a 12.2-m (40-ft) two-pass extended cut face, the continuous miner is always at the point of deepest penetration, and operation of the machine-mounted dust scrubber and water spray system improve the flow of fresh air to the end of the box cut. However, when the continuous miner leaves the box cut to begin cutting the 40-ft slab, little is known about how much ventilation air reaches the end of the box cut. The Pittsburgh Research Laboratory (PRL) of the National Institute for Occupational Safety and Health conducted a full-scale study to answer this question. Tests were run to determine how much ventilation air reaches the end of the box cut with the continuous miner at three locations in the 40-fttwo-pass extended cut mining sequence; at the end of the 40-ft box cut, at the start of the 40-ft slab cut, and 6.1 m (20 ft) into the slab cut. During these tests, methane gas was uniformly released at the end of the 40-ft box cut. Methane concentrations measured0.3 m (1 ft) from the roof and face of the box cut were used to estimate face airflow quantities. Fresh air flow rates of 1.89and 4.72 m/sec (4,000 and 10.000 cfm), scrubber flow rates of 0, 4,000 and 10,000 cfm, water spray pressures of 0 and3827 kPa (0 and 120 psi), and a blowing curtain setback position of 15.2m (50 ft) were used during these tests. To improve ventilation to the end of the 40-ft box cut when the continuous miner was starting the 40-ft slab cut and 20 ft into the slab cut, the blowing curtain was advanced from its 50-ft setback to locations 40-ft and then 8.5 m (28 ft) from the face. KEYWORDS: Face ventilation, Extended cut, Methane, Box cut, Continuous miner, Scrubber

By Leroy Dockter

The grinding characteristics of lignite in a ball mill were investigated. The variables studied were initial lignite moisture content, degree of in-the-mill drying, and lignite source. The mill tested was a pilot-p1ant-size conical ball mill which had a maximum output of from 80 to 180 lb/hr pulverized product depending on the lignite and test conditions. The capacity of the test mill ranged from 82 to 103 lb/hr depending upon mine source, in pulverization of as-mined lignite with minimum drying, The capabilities of the ball mill could not be correlated to Hardgrove index of the individual lignites or other observed physical properties. Predrying lignite from its 35 to 40 percent raw moisture content to about 10 percent moisture before grinding improved the mill capacity 87 percent, compared to an increase in capacity of 74 percent with in-the-mi11 drying to the same product moisture.

Jan 1, 1967

By Garrett R. Hyde

Sintered yttria and sintered dysprosia can be used to make single-component thermistors having typical thermistor geometries and operable in the temperature range 500° to 1,200° C. However, at these temperatures, instability of platinum electrodes can contribute a slight aging effect if the thermistor is kept near 1,200° C for long periods. Typical characteristics at 500° C for an yttria disk thermistor 12 mm in diameter and 2 mm thick are a resistance of 12.4 megohms and a temperature coefficient of resistance of -3.8 percent per degree C. Typical characteristics at 500° C for a dysprosia thermistor of the same dimensions are a resistance of 1.84 kohms and a temperature coefficient of resistance of -1.6 percent per degree C.

Jan 1, 1970

By Scott Turner

We have gathered here in Pittsburgh, at the Nineteenth Annual Safety Congress, in order to advance the cause of safety. Although my personal inter- est in this movement alone would have been sufficient to insure my presence here, specific duties have brought me to this congress in an official capacity. My responsibilities as the head of the United States Bureau of Mines, which makes the promotion of safety in the mining and allied industries one of its major activities, necessitate my attendance. My obligations as president of the Joseph A. Holmes Safety Association, an organization closely allied to the bureau and which has for one of its objects the public recognition and reward of outstanding achievements in safety, require that I be present at this time. This morning, my job is to present the Holmes safety certificate to the Lehigh Portland Cement Co. First I will remind you of the nature of this safety association, named in honor of the first director of the Bureau of Mines. After Mr. Holmes' death, in 1915, a number of influential organizations banded together to commemorate the name of this leader in the conservation of human life. In order that you may appreciate the significance of an award by the Joseph A. Holmes Safety Association, I shall read you the list of 24 national organizations which comprise its membership:

Nov 1, 1930

By Fred C. Turin, Lisa J. Steiner, Kim M. Cornelius

Like many experienced workers, remote control continuous miner operators perform their everyday jobs making choices and decisions that they may not consciously think about. While performing tasks, they are continuously processing feedback and cues which guide them for the next move. Initial training teaches the operators the tasks necessary to operate the equipment and perform the job. However, with experience they are better able to deal with hazardous conditions and non routine situations. To better understand what potential cues and feedback help to guide the operators, a questionnaire was developed to learn what factors affect decisions. Operator responses address issues related to specific tasks, equipment operation, visibility, lighting, and communication issues. The information collected is useful to understand what cues experienced operators use to make task performance decisions. Results will be used to develop interventions and training for safe and effective operator performance.

By James S. Browning

Domestic production of lithium minerals, source of the lightest metallic element, has increased from an average of 1,327 short tons of concentrate in the 1935-39 period to approximately 37,830 short tons in 1954. This rather phenomenal growth in production and use reflects growing industrial interest in the metal and its salts. This information circular has been prepared to summarize for the casual technical reader the reserve, mining, processing, and consumption situation pertaining to the mineral spodumene - the principal source of lithium. A relatively complete bibliography is included for those who may need more detailed information.

Jan 1, 1958

By G. W. Jones

[A survey of the literature relating to ignition temperatures of acetylene-air and acetylene-oxygen mixtures reveals rather wide disagreement in the reported results. In some instances the ignition temperatures of acetylene-air mixtures were reported to be lower then those of acetylene-oxygen mixtures, which is contrary to experience with other combustibles. To clear up some of the reported discrepancies, the authors have investigated the ignition temperatures of acetylene both in air and oxygen, and their results are presented in this report.]

Jan 1, 1941

By George H. Schnakenberg

This Bureau of Mines publication describes a passive personal sampling device for N02 in air, developed by the New York University Medical Center under Bureau Grant G0133066. The sampler has been successfully demonstrated in the field and in the laboratory. In corroborative laboratory trials the agreement with reference method is excellent. The overall accuracy is approximately ±5 pct of reading to a precision of about ±l pct. All evidence indicates that these samplers should indicate the time-weighted-average N02 concentration to the above accuracy and precision equally well in the field since effects of wind velocity and relative humidity are negligible and the effects of temperature are about 0.1 pct per °F. The duration of exposure and the approximate temperature are the only data that need to be collected in the field. A two-step analysis procedure in field or service laboratory is then used to obtain the total cumulated exposure to N02 in parts per million-hours (ppm times hours), which can be converted to the time-weighted-average concentration of N02 in ppm by dividing cumulated exposure by the duration of the exposure.

Jan 1, 1976

By Robert K. Koch

The reactions of alumina and alumina monohydrate with wet hydrogen fluoride gas were studied by the Federal Bureau of Mines to determine the feasibility of producing commercial-grade aluminum fluoride from offgases generated by pyrohydrolysis of siliceous fluorspars. The test results showed than an aluminum fluoride reactor operating at maximum efficiency could retain 96 percent of the fluorine contained in off-gases generated by pyrohydrolysis of siliceous fluorspar. The requirements are a reactor temperature of 200° C. and a reactor entrance gas containing 5 mole-percent hydrogen fluoride. Partial pressure equilibrium constants were determined for the reaction of alumina monohydrate and wet hydrogen fluoride gas from 200° to 350° C. and for the reaction of alumina and wet hydrogen fluoride gas from 350° to 700° C. Both reactions are reversible, and they proceed in directions that are dependent upon the temperature and the relative HF:H2O concentration. Logarithms of the equilibrium constants were used to plot the reaction isobars; these can be used to calculate the theoretical maximum efficiency of a reactor processing wet hydrogen fluoride gas between 200° and 700° C. The theoretical maximum efficiency decreases with increasing temperature.

Jan 1, 1961

Objective To accurately measure very low air velocities (0-100 ft/min) in U.S. large-opening underground metal/nonmetal mines. Background Hundreds of metal/nonmetal underground mines operate throughout the United States. They extract commercial products from deposits such as limestone, salt, and gypsum. Mining generates a wide variety of gases and dusts, such as silica, diesel exhaust, radon, blasting byproducts, and perhaps even methane. If these substances become airborne, they can adversely affect the health and safety of underground workers. Many metal/nonmetal mines have large cross-sectional airways that could be 60 times larger than an average underground coal mine entry. These large airways require adequate volumes of fresh air to dilute, make harmless, and exhaust the toxic and, at times, explosive byproducts. However, in some underground mine sections, air movement is barely perceptible. The technology of measuring very low air velocities will become increasingly more important for operators of large-opening stone mines in order to monitor miner exposure to diesel particulate matter. Conventional anemometers (e.g., vane) are capable of accurately measuring air velocities only above 100 ft/min. Thus, it was necessary to investigate other anemometry technology to detect low air velocities in the range of 0-100 ft/min. Two different portable ultrasonic anemometers were tested. Actual testing was done in an underground limestone mine with openings about 51 ft wide by 29 ft high. Ultrasonic Anemometers Vane-type anemometers are commonly used by engineering personnel throughout the underground coal mine industry. They work well in measuring air velocities >100 ft/min. However, a separate technology, e.g., portable ultrasonics, is needed to measure air velocities much below 100 ft/min at various places within the large mine opening. Laser-doppler technology was also considered for this application, but was ruled out because of its high cost and other technical limitations. With no moving parts, the portable ultrasonic anemometers are claimed to be accurate down to about 1or 2 ft/min. The first type of ultrasonic anemometer that was examined underground is manufactured by Gill Instruments Ltd., Hampshire, U.K. The U.S. distributor is IN USA, Needham, MA. The Gill Instruments Solent Volometer (figure 1) is a battery-powered, single-axis anemometer meant for measuring low to medium air flows up to1,999 ft/min. It uses the ultrasonic "time of flight" principle where pulses of high-frequency sound are transmitted along the air flow path and the time taken to reach the receiver is measured. The faster the air speed, the quicker the pulses reach the receiver. The second ultrasonic anemometer that was examined under-ground is manufactured by Airflow Developments Ltd., Buckinghamshire, U.K. The U.S. distributor is Airflow Technical Products, Inc., Andover, NJ. The Anemosonic UA-6 (figure 2) is a battery-powered, handheld instrument with digital display. It measures air velocity (0 to 9,999 ft/min) or volume flow, flow turbulence intensity, and air temperature. Neither device is considered to be intrinsically safe for use in underground gassy coal mines. A comparison of salient specifications of both instruments is shown in table 1. The total suspended weight includes the instrument (Gill) or instrument probe (Airflow) plus about 35 ft of connecting cable attached to the pole. This combination of instrument plus cable length allows two operators to measure air velocities up to about 30 ft above the mine floor. Figures 1 and 2 show how each unit would be attached to an extensible, graduated fiberglass rod in order to position the sensor probe at a certain spatial point (centroid of the quadrate) within the underground large opening.

Jan 1, 2003

By Alla D. Mah

The heat of combustion of TaC0.996 was determined by oxygen bomb calorimetry to be -302.8 ±0.4 kcal/mole. The corresponding heat of formation of TaC0.996 is -35.4 ±0.5 kcal/mole, and the calculated heat of formation of TaC1.00 is -35.5 ±0.5 kcal/mole.

Jan 1, 1965

By R. D. Currie

The practicability and dependability of two permissible methane-indicat- in detectors recently developed were proved conclusively by extensive tests in the return airways of all mines operating in the anthracite region in most of which samples and readings were taken with one or the other of the two in- dicating detectors. These detectors roved dependable and accurate within practical limits, and their general use should be encouraged as an aid to bet ter ventilation, more accurate control of air currents, and greater safety in mines.

Feb 1, 1936

By W. H. Ode, W. A. Selvig

In 1938 , the Bureau of Mines cooperated with Subcommittee XV on Plasticity and Swelling of Coal ( C. C. Russell , chairman ) , of Committee D-5 on Coal and Coke , A.S.T.M. , by testing various methods for determining expansion and plastic properties of a series of coals of widely different coking properties . One of the tests made by the Bureau was the British Standard Method for the Crucible Swelling Test for Coal.5/ Briefly , this swelling test consists in heating 1 gram of pulverized coal in a silica crucible over a gas flame under prescribed conditions to form a coke button which is compared in size and shape with a series of standard profiles numbered 1 to 9. These profiles are intended to cover the size and shape of buttons obtained from coals covering a wide range in plastic properties .. The number of the standard profile with which the maximum cross -sectional area of the button most nearly corresponds is recorded as the swelling index . Although the swelling test showed poor relationships with the various tests that were used for measuring expansion or contraction of coal during carbonization , it gave indications of having value in measuring free - swelling and caking properties of coals when burned on fuel beds . An opportunity to investigate this occurred when an engineer of an eastern public utility 'company reported pronounced differences in burning characteristics on grates of various shipments of Pocahontas coal . Some of these coals gave trouble by swelling 'excessively and clogging the grates . Samples were ob- · tained , and it was found that the troublesome coals gave decidedly higher free -swelling numbers than did the coals that performed satisfactorily . Also , it was found that the free - swelling index test gave better differentiation between coals than could be obtained from the coke buttons from the · ´`standard volatile -matter test or from agglutinating - value results . The results of the free - swelling tests were considered by the Subcommittee on Plasticity and Swelling , and a special group of the subcommittee , under the chairmanship of R. A. Sherman , was delegated to study the test method . Ostborg , Limbacher , and Sherman , ofthe Battelle Memorial Institute , ' investigated the various factors affecting the test and found that the swelling index was a good indication of the suitability of coal for performance on residential -type stokers from the standpoint of the coking characteristics of the coal . Data were presented also showing that the indexes wer helpful in the selection of coal for industrial underfeed stokers .

Oct 1, 1946

By L. C. IlsLey

"Nearly every piece of electrical equipment used in mines ""breathes."" In other words, motors, controllers, rheostats, switches, and other similar equipment, even though encased in seemingly tight compartments, breathe in the atmosphere that surrounds them.As the apparatus is used, the temperature of metallic parts is changed generally in positive direction through the heat by friction and the heat due to the electric current. When the apparatus is idle it gradually cools down to the temperature of the surrounding atmosphere.This increase of temperature during operation and return to normal temperature when operation stops alternately raises and lowers the temperature of the atmosphere within the compartments which, in strict accordance with Charles' law -will expand or contract in proportion to any given temperature change.As compartments are not gas-tight, such expansion and contraction will force the atmosphere out of the compartment =on expansion and suck the surround¬ing atmosphere into the compartment during contraction, hence the term ""breathing.""Investigators2 of explosion-proof equipment have recognized that such an interchange would take place and have designed their equipment to safeguard possible explosions within the compartments."

Jun 1, 1927

By R. R. Backer

The Bureau of Mines, in cooperation with Washington Irrigation and Development Co. (WIDCO), evaluated the dewatering of fine coal-refuse slurry using chemicals and various types and combinations of drains in natural earth impoundments. About 40 lb of lime and 2 lb of polymer per ton of dry solids were mixed with the underflow from the preparation-plant thickener. Clear, free water was immediately liberated from the slurry. The percent solids by weight of the slurry increased from about 17 to 30 immediately, and after 5 days increased to 45 wt-pct. This indicates a threefold reduction in total volume after 5 days from 172 cu ft/ton solids originally to 56 cu ft/ton solids.

Jan 1, 1981

By Russell C. Frith, David C. Oyler, Dolinar Dennis R., Christopher Mark

Unusual circumstances may require that a longwall retreat into or through a previously driven room. The operation can be completed successfully, but there have been a number of spectacular failures. To help determine what factors contribute to such failures, a comprehensive international database of 131 case histories has been compiled. The cases include six failures where major rock falls occurred in front of the shields, and seven even more serious failures involving major overburden weighting. The case studies suggest two types of room failure mechanism. The first is a roof fall type failure caused by loading of the immediate roof at the face as the fender or remnant longwall panel narrows. The second is an overburden weighting type failure caused by the inability of the roof to bridge the recovery room and face area, and affecting rockwell above the immediate roof. The data indicate that the roof fall type of failure is less likely when intensive roof reinforcement (bolts, cables and trusses) is employed together with higher-capacity shields. The overburden weighting failures, in contrast, occurred when the roof was weak and little standing support was used. Weighting failures were not greatly affected by the density of roof reinforcement. In one of the overburden weighting cases, in a Pittsburgh coal bed mine, stress cell, convergence, bolt load and extensometer data have been used to analyze the failure in detail. Key words: coal mining, ground control, longwall, recovery room.